Junlan Electronic CAB0111 Bluetooth Speaker User Manual BT111GB English manual
Shenzhen Junlan Electronic Ltd Bluetooth Speaker BT111GB English manual
User manual
BLUETOOTH
SPEAKER SYSTEM
Instruction Manual
Model: BT111GB
Read these instructions carefully before use
Safety instructions
Please avoid placing the unit in places with high humidity, high temperature,
grease, contamination, etc. Please do not place the unit in direct sunlight or rain.
Avoid dropping the unit.
When the unit gets dirty on the surface, please clean with damp cloth. Do not use
any organic solvents, paint thinner or abrasive cleaners.
Never privately dissemble, repair or modify unit. Contact our service center for
repair information
1
LOCATION OF CONTROLS
2
12
1. Indicators
2. Speakers
3. Power ON/OFF switch
4. USB Charger: USB cable only for charging
5. Line in jack
6. Hands-off/Power button
7. Volume+- button
8. / Previous/Next button
3 4 5
6
7
8
USB CHARGER
Bluetooth Connection
3
Line in connection
1. Connect an audio connection cable with 3.5mm stereo plug (not included)
to the line in jack on the rear of the unit.
2. Connect the other end to the audio out jack/ phone jack on the MP3 or other
external device.
3. Turn on the external device and press Play button to start playing the music.
4. Press + button to increase the volume. Press- button to decrease the volume.
1.Connect the Bluetooth speaker via USB cord (included).
2.Move the Power On/Off button on the rear of the unit to On position. The
red indicator light will come on.
3.Press the Power Button on the right side of the unit to turn on the unit. The
blue indicator light will turn on and flash. Press and hold Power Button to
turn the unit to Standby mode. During playback, press Power Button to
pause and press again to resume the playback.
When the unit is powered on the Bluetooth indicator blue light will turn on
and flash and the unit will enter Bluetooth mode.
4.Allow your cell phone to enter the Bluetooth connection mode. During
searching, the blue Bluetooth indicator will keep flashing. When searching
is completed, select BT111 as the target equipment.
When connected, the Bluetooth indicator blue light will stay lit.
5. Press. to skip to the previous track. Press to skip to the next track.
6. Press + button to increase the volume. Press- button to decrease the volume.
7. The built-in Mic of this unit enables hands-free function in Bluetooth mode.
When the call comes in press Hands-free button to answer the call.
Press Hands-free button again to hang up.
Press Hands-free button to redial the last outgoing call.
Battery Charging
The unit provides a built-in 3.7V 1000mAh Lithium battery. The standard
voltage is 3.7V. The maximum voltage is 4.2V.
1. The minimum working voltage of the unit is 3.5V.When the battery voltage
is under 3.5V, the red indicator will stay lit to indicate the low voltage status
and the battery needs to be recharged.
2. Connect one end of the USB charging cable (included) to the DC in jack on
the rear of the unit. Connect the other end to your PC. Or you can connect
the other end to a 5V AC/DC adapter (not included) to power and charge the
unit. Then the green indicator will stay lit to indicate that the battery is in
charging status.
3. When the voltage reaches the Maximum voltage 4.2V, the green indicator
will turn off to indicate that the charging process is completed.
4
SPECIFICATIONS
Bluetooth technology 2.0+EDR
RMS Output 2x 2W
Effective distance of Bluetooth approximately 33 feet
Speaker impedance 4 Ohm 3Wx2
Playback time
ACCESSORIES
User Manual 1PC
USB charging cable 1PC
5
approximately 3 hours
(With volume set to ½ of Maximum volume)
TROUBLE SHOOTING GUIDE
Check the followings before requesting service:
SYMPTOM POSSIBLE CAUSE POSSIBLE SOLUTION
No power
No sound
Bluetooth
reception failure
Hands free
not working
The built-in battery runs
out
Power switch is in OFF
position
Power button on the
unit not pressed
Recharge the battery
Move the power switch on the rear
of the unit to ON position
Press the POWER button on
the right side of the unit to turn
on the unit
Volume in minimum
position of the unit
The connected device is
not in playback mode
Sound output of the
connected device weak
Input source incorrect
Raise volume by pressing the
VOL+ button
Play the music in the
connected device
Raise the volume level of the
connected device
Set input source as Line-in or
Bluetooth mode
Not in Bluetooth mode
Line in cable in the
Line in jack
Set to Bluetooth mode and the
blue indicator will turn on
Disconnect the line in cable
Not in Bluetooth mode
Set as Bluetooth mode(Hands
free function is only available in
Bluetooth mode)
6
7
LIMITED WARRANTY
FCC Statement
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.