Junlan Electronic CHT914N HOME THEATER SPEAKER SYSTEM WITH BLUETOOTH User Manual CHT910

Shenzhen Junlan Electronic Ltd HOME THEATER SPEAKER SYSTEM WITH BLUETOOTH CHT910

user manual

TOWER STEREO SYSTEMTOWER STEREO SYSTEMOwner's ManualPLEASE READ BEFORE OPERATING THIS EQUIPMENT.Model: CHT914n
IMPORTANT SAFETY INSTRUCTIONS
Insert the AC plug into a conveniently located AC outlet having AC 120V~60Hz.NOTE: The AC plug supplied with the unit is polarized to help minimize the obsolete outlet. possibility of electric shock. If the AC plug dose not fit into a non polarized AC outlet, do not file or cut the wide blade. It is the user's responsibility to have an electrician replacing the1. Plastic Holder2. Remote Sensor3. Speakers4. Speaker Net5. Wooden Base6. Washers12356737. Screws MAIN UNIT-- RIGHT CHANNEL SPEAKER1LEFT CHANNEL SPEAKER45311. Speakers2. Speaker Net3. Wooden Base4. Screws5. WashersNote:1. Assemble the wooden base to the main body with the supplied screws and washers as Fig. 2 & 4 above.2.The speaker net can be taken out and reassembled as Fig.1 & 3 above. Figure 324 Figure 4 Figure 2 Figure 1i Figure 53.Install the Plastic HolderiExternal Device Plastic Holder on the top of unit to hold the external device as Fig. 5 above.POWER SOURCEINSTALLATION
7. / (Play/Pause) button8. TUNE - button9. AUX IN 2 jack10. 11. SOURCE indicator1. USB Port (For recharge only)2. 3. STANDBY indicator4. SOURCE button5. / TUNE + button VOL- (Volume Down) button6. VOL+ (Volume Up) button 12. 13. AUX IN 1 jacks14. FM Antenna (Power) button1213141239456781011 MAIN UNITSpeaker Connector(For Left Channel Speaker)LOCATION OF CONTROLS
12345678REMOTE CONTROL1. POWER button2. /TUNE - button3. VOL (Volume)+/- buttons4. SOURCE button5. (Mute) button6. / TUNE+ button7 (Play/Pause) button8 EQ (Equalizer) button7LOCATION OF CONTROLS
Fig.1 Fig.2 Fig.3BATTERY PRECAUTIONSEFFECTIVE DISTANCE OF REMOTE TRANSMITTERApprox.15 feet-First Time UseRemove and discard the insulation tab as figure on the right-Replacing Batteries For Remote Control1. Push and slide out the battery holder as figure 1 below.2. Replace the battery with a new CR2025 button cell as the polarity markings on the rear of the Remote Control. 3. Close the battery holder..Remote Sensor, onthe front of main unitBATTERY INSTALLATION--- REMOTE CONTROL
7GENERAL OPERATIONSLEFT SPEAKER CONNECTIONBlack wireRed wireMain Unit Left Speaker Connect the connection wires (Red and Black) from Left Speaker to the Speaker Connectors on the rear of Main Unit as the figure above.1.Insert the AC Power Cord into conveniently located AC outlet having AC 120V~60Hz.The Red Standby Indicator will light.2.Press Power button on the Unit or Remote Control to power on the unit. The Red Standby Indicator will turn off and source Indicator will light.corresponding color as below:3.Press the SOURCE button repeatedly to switch to desired mode.The source Indicator will turn to ~ Green: Radio~ Blue: Bluetooth~ Purple: AUX IN 1~ Orange: AUX IN 24.During Playback:~ Press the VOL (Volume) buttons to adjust volume level as desired.~ Press EQ button repeatedly to select and set equalizer mode as desired.~ Press (Mute) button on the Remote Control to turn off the sound. Press again to resume.5.When finished listening, press Power button to power off the unit. The source Indicator will turn off and Red Standby Indicator will light.wall outlet if a long period of time will not use. NOTE: For saving energy, unplug the Power AC Cord from
FM AntennaLISTEN TO FM RADIO1.Power ON the unit as previous procedures.2.Press the SOURCE button repeatedly until the color of source Indicator turns Green.4.Repeat the same procedures until the desired radio station is received.NOTE: If the received FM station is in stereo mode, the unit will play it in stereo mode automatically.3.Press and hold the /TUNE - or /TUNE + buttons until the source Indicator start blinking. The unit will start to search next (or previous) available FM radio station then plays.The Antenna wire on the rear of Main Unit is for radio reception. If reception is weak, unwind and extend the wire or relocate the wire to improve the radio reception. MP3 Player; Discman ... etc.).WhiteRedLISTEN TO TV/DVD/VCR/DVRX IN 1Audio out jacks on TV/DVD/ VCR/DVRDVDR L AUX IN 1N 14. Press SOURCE button repeatedly until the indicator turns Purple.1. Connect one end of RCA audio connection cable (not supplied) to the AUX IN 1 jacks on the rear of the unit as the figure above.2. Connect the other end to the AUX out jacks on the external player (such as Television, VCR, DVD Player, DVR ... etc.).5. Play the music in the external player as usual. (Make sure the volume output level of the player is in high level. Otherwise, sound from this unit is weak).83. Power on the unit as previous procedures.
93. Power on the unit as previous procedures.4. Press the SOURCE button repeatedly until the color of source Indicator turns Orange.1. Connect one end of supplied audio connection cable to the AUX IN 2 jack on the top of the unit.2. Connect the other end to the AUX out/Line out/Phone jack on the external player (such like iPod, iPhone, iPad, MP3 Player, Discman... etc.).5. Play the music in the external player as usual. (Make sure the volume output level of the player is in high level. Otherwise, sound from this unit is weak). as the figure above.LISTEN TO EXTERNAL AUDIO DEVICESAUX IN 2 jack
10BLUETOOTH PARING AND PLAYBACK1. Power on the unit as previous procedures.2. Press the SOURCE button on the unit or remote control until the indicator turns blue.3. Turn on the BT function on the external BT device and play the music as usual. (Make sure the volume level of the external BT device is set to high level).4. During palyback: Press the VOL (Volume) +/- buttons to adjust volume level. Press the / TUNE- or / TUNE + button to skip track. Press the (Play/Pause) button to pause. Press again to to resume normal playback.NOTES:1. During the first time use, pair the external BT device as below: A. Power on the unit as previous procedures and press the SOURCE button repeatedly until the indicator turns blue and blinking. B. Power on the external BT device and enter searching mode. Start paring as the on screen instructions on the external BT player(For detailed paring procedures, please refer to the user's manual of your BT device.)C. When the external BT player searched the Speaker, our model number"CHT914n" will appear on the display of the external BT device. Paring code"0000" may need to enter.The USB port in this unit is for recharge only. Recharge the USB device as below:2. Insert the full size USB Plug from the USB connection cable to the USB port on the top of unit.3. Charging will start automatically.4. When finished, disconnect the full size USB Plug from the unit. You can also charge the connected device when the unit is in Standby mode.1. Connect the small plug from the USB connection cable to the device as usual. (Connection cable not supplied).NOTES:The maximum output from the USB port is DC 5V, 2.1A. You can change any rechargeable USB devices charging current less than it, such like IPod, IPhone, IPad, MP3 Player … etc.USB PORT
11Check the followings before requesting serviceSYMPTOM POSSIBLE CAUSE POSSIBLE SOULTIONNo power AC plug not connected to the Plug to the wall outlet.No soundVolume in minimum position Raise volume level by pressing the VOL (Volume) + buttonThe connected device is not in payback modePlay the music/movie in the connected device as usualInput source incorrectwall outletSound distortionVolume level too high VOL (Volume ) - buttonReduce the bass level of the connectedReduce the volume level by pressing the Bass level of the connected device too high deviceBluetooth reception failureThe external device is far fromthe unitHave not paired Pair both unit as BT pairing pageTROUBLESHOOTING GUIDERemote not The batteries are consumed Replace with new batteryworking desired mode.Press the SOURCE button repeatedly to set the input source to the desired modePut the external BT device close to the unitand make sure the volume level of it is in high level
12Power Source...........................................................................................................AC 120V~60HzRadio Coverage................................................................................................FM 87.5 -108.0 MHzRemote working distance.............................................................................................Up to 15 feetImpedance of : Loud .......................................................................................................8 Ohm, 10W x 2 Tweeters................................................................................................................... 8 Ohm, 5W x 2Bluetooth working distance......................................................................................... Up to 30 feet (Measured in open area. Wall and structures may affect the effective range.) 1 x User Manual1 x Remote Control, using CR 2025 button cell (Already installed in the remote control) 1 x Stereo Audio Connection Cable with 3.5mm stereo plug 4 x Assembly Screws / WashersAccessories 2 x Wooden Bases 1 x Plastic HolderPower Consumption...................................................................................................................45WUSB port output ..............................................................................................DC 5V, Max. 2.1ASpeakersSpeakersGENERAL SPECIFICATIONS
Craig warrants this product to be free from manufacturing defects in material andworkmanship under normal use for a period of 90 days from date of purchase. If serviceis required, please return the product to the store where it was purchased for exchange;or, pack the unit in the original packing material with all accessories if applicable, a copyof your sales receipt and a Cashier’s check or Money Order for $20.00 (to cover shippingand handling costs) payable to Craig Electronics Inc. For consumers in Canada, pleasemake sure that the cashier check or money order is redeemable through a U.S. bank.Ship your product freight pre-paid. Your unit will be repaired, replaced or if the unit cannot be repaired or replaced, a refund will be forwarded to you within four weeks of receiptof your unit. Please ship your unit to:Craig Electronics Inc.1160 NW 163 DriveMiami, Fl 33169This warranty is void if the product has been: a) Used in a commercial application orrental. b) Damaged through misuse, negligence, or abuse. c) Modified or repaired byanyone other than an authorized Craig service center. d) Damaged because it isimproperly connected to any other equipment.Note: This warranty does not cover: a) Ordinary adjustments as outlined in the Owner’sManual which can be performed by the customer. b) Damage to equipment not properlyconnected to the product. c) Any cost incurred in shipping the product for repair. d)Damage to the product not used in the USA.This warranty is not transferable and only applies to the original purchase. Any impliedwarranties, including the warranty of merchantability, are limited in duration to the periodof this expressed warranty and no warranty whether expressed or implied shall apply tothe product thereafter.Under no circumstance shall Craig be liable for any loss or consequential damage arisingout of the use of this product. This warranty gives specific legal rights. However, you mayhave other rights which may vary from state to state. Some states do not allow limitationson implied warranties or exclusion of consequential damage. Therefore, theserestrictions may not apply to you.To Obtain Service on your Productemail:service@craigelectronics.comLIMITED WARRANTYPrinted in China CHT910-IB-E0CL1-B0US

Navigation menu