Junlan Electronic CHT914N HOME THEATER SPEAKER SYSTEM WITH BLUETOOTH User Manual CHT910

Shenzhen Junlan Electronic Ltd HOME THEATER SPEAKER SYSTEM WITH BLUETOOTH CHT910

user manual

Download: Junlan Electronic CHT914N HOME THEATER SPEAKER SYSTEM WITH BLUETOOTH User Manual CHT910
Mirror Download [FCC.gov]Junlan Electronic CHT914N HOME THEATER SPEAKER SYSTEM WITH BLUETOOTH User Manual CHT910
Document ID1881732
Application IDwbpj4w3UL9xBiLHX7oSV3Q==
Document Descriptionuser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize236.69kB (2958664 bits)
Date Submitted2013-01-17 00:00:00
Date Available2013-01-17 00:00:00
Creation Date2011-12-24 06:20:44
Producing SoftwareCorel PDF Engine Version 14.0.0.653
Document Lastmod0000-00-00 00:00:00
Document TitleCHT910.cdr
Document CreatorCorelDRAW
Document Author: Administrator

TOWER
TOWER STEREO
STEREO SYSTEM
SYSTEM
Owner's Manual
PLEASE READ BEFORE OPERATING THIS EQUIPMENT.
Model: CHT914n
IMPORTANT SAFETY INSTRUCTIONS
POWER SOURCE
Insert the AC plug into a conveniently located AC outlet having AC 120V~60Hz.
NOTE: The AC plug supplied with the unit is polarized to help minimize the
possibility of electric shock. If the AC plug dose not fit into a non polarized
AC outlet, do not file or cut the wide blade. It is the user's responsibility to
have an electrician replacing the obsolete outlet.
INSTALLATION
MAIN UNIT-- RIGHT CHANNEL SPEAKER
LEFT CHANNEL SPEAKER
Figure 3
Figure 4
Figure 1
Figure 2
1. Plastic Holder
2. Remote Sensor
3. Speakers
4. Speaker Net
5. Wooden Base
6. Washers
7. Screws
External Device
Plastic Holder
1. Speakers
2. Speaker Net
3. Wooden Base
4. Screws
5. Washers
Figure 5
Note:
1. Assemble the wooden base to the main body with the supplied screws and washers as Fig. 2 & 4 above.
2.The speaker net can be taken out and reassembled as Fig.1 & 3 above.
3.Install the Plastic Holder on the top of unit to hold the external device as Fig. 5 above.
LOCATION OF CONTROLS
MAIN UNIT
8. VOL- (Volume Down) button
9. AUX IN 2 jack
10.
(Play/Pause) button
11. SOURCE indicator
12. Speaker Connector
(For Left Channel Speaker)
13. AUX IN 1 jacks
14. FM Antenna
1. USB Port (For recharge only)
2.
(Power) button
3. STANDBY indicator
4. SOURCE button
5.
/ TUNE + button
6. VOL+ (Volume Up) button
7.
/ TUNE - button
11
10
14
12
13
LOCATION OF CONTROLS
REMOTE CONTROL
1.
POWER button
2.
/TUNE - button
3. VOL (Volume)+/- buttons
4. SOURCE button
5.
(Mute) button
6.
/ TUNE+ button
(Play/Pause) button
8 EQ (Equalizer) button
BATTERY INSTALLATION--- REMOTE CONTROL
-First Time Use
Remove and discard the insulation tab as figure on the right
-Replacing Batteries For Remote Control
1. Push and slide out the battery holder as figure 1 below.
2. Replace the battery with a new CR2025 button cell as the
polarity markings on the rear of the Remote Control.
3. Close the battery holder.
Fig.1
Fig.2
Fig.3
BATTERY PRECAUTIONS
EFFECTIVE DISTANCE OF REMOTE TRANSMITTER
Remote Sensor, on
the front of main unit
Approx.15 feet
LEFT SPEAKER CONNECTION
Black wire
Main Unit
Red wire
Left Speaker
Connect the connection wires (Red and Black) from Left Speaker to the Speaker Connectors
on the rear of Main Unit as the figure above.
GENERAL OPERATIONS
1.Insert the AC Power Cord into conveniently located AC outlet having AC 120V~60Hz.The Red
Standby Indicator will light.
2.Press
Power button on the Unit or Remote Control to power on the unit. The Red Standby
Indicator will turn off and source Indicator will light.
3.Press the SOURCE button repeatedly to switch to desired mode.The source Indicator will turn
to corresponding color as below:
~ Green: Radio
~ Blue: Bluetooth
~ Purple: AUX IN 1
~ Orange: AUX IN 2
4.During Playback:
~ Press the VOL (Volume) buttons to adjust volume level as desired.
~ Press EQ button repeatedly to select and set equalizer mode as desired.
~ Press (Mute) button on the Remote Control to turn off the sound. Press again to resume.
5.When finished listening, press
Power button to power off the unit. The source Indicator will
turn off and Red Standby Indicator will light.
NOTE:
For saving energy, unplug the Power AC Cord from wall outlet if a long period of time will not use.
LISTEN TO FM RADIO
1.Power ON the unit as previous procedures.
2.Press the SOURCE button repeatedly until the color of source Indicator turns Green.
3.Press and hold the
/TUNE - or
/TUNE + buttons until the source Indicator start blinking.
The unit will start to search next (or previous) available FM radio station then plays.
4.Repeat the same procedures until the desired radio station is received.
NOTE: If the received FM station is in stereo mode, the unit will play it in stereo mode automatically.
FM Antenna
The Antenna wire on the rear of Main Unit is for radio reception. If reception is weak, unwind and
extend the wire or relocate the wire to improve the radio reception.
LISTEN TO TV/DVD/VCR/DVR
Red
N1
X IN 1
Audio out jacks on
TV/DVD/ VCR/DVR
AUX IN 1
White
DVD
1. Connect one end of RCA audio connection cable (not supplied) to the AUX IN 1 jacks on the rear
of the unit as the figure above.
2. Connect the other end to the AUX out jacks on the external player (such as Television, VCR, DVD
Player, DVR ... etc.).
3. Power on the unit as previous procedures.
4. Press SOURCE button repeatedly until the indicator turns Purple.
5. Play the music in the external player as usual. (Make sure the volume output level of the player is
in high level. Otherwise, sound from this unit is weak).
LISTEN TO EXTERNAL AUDIO DEVICES
AUX IN 2 jack
1. Connect one end of supplied audio connection cable to the AUX IN 2 jack on the top of the unit.
as the figure above.
2. Connect the other end to the AUX out/Line out/Phone jack on the external player (such like iPod,
iPhone, iPad, MP3 Player, Discman... etc.).
3. Power on the unit as previous procedures.
4. Press the SOURCE button repeatedly until the color of source Indicator turns Orange.
5. Play the music in the external player as usual. (Make sure the volume output level of the player
is in high level. Otherwise, sound from this unit is weak).
BLUETOOTH PARING AND PLAYBACK
1. Power on the unit as previous procedures.
2. Press the SOURCE button on the unit or remote control until the indicator turns blue.
3. Turn on the BT function on the external BT device and play the music as usual. (Make sure
the volume level of the external BT device is set to high level).
4. During palyback:
Press the VOL (Volume) +/- buttons to adjust volume level.
Press the
/ TUNE- or
/ TUNE + button to skip track.
Press the (Play/Pause) button to pause. Press again to to resume normal playback.
NOTES:
1. During the first time use, pair the external BT device as below:
A. Power on the unit as previous procedures and press the SOURCE button repeatedly until the
indicator turns blue and blinking.
B. Power on the external BT device and enter searching mode. Start paring as the on screen
instructions on the external BT player(For detailed paring procedures, please refer to
the user's manual of your BT device.)
C. When the external BT player searched the Speaker, our model number"CHT914n" will
appear on the display of the external BT device. Paring code"0000" may need to enter.
USB PORT
The USB port in this unit is for recharge only. Recharge the USB device as below:
1. Connect the small plug from the USB connection cable to the device as usual. (Connection cable
not supplied).
2. Insert the full size USB Plug from the USB connection cable to the USB port on the top of unit.
3. Charging will start automatically.
4. When finished, disconnect the full size USB Plug from the unit.
NOTES:
The maximum output from the USB port is DC 5V, 2.1A. You can change any rechargeable USB
devices charging current less than it, such like IPod, IPhone, IPad, MP3 Player … etc.
You can also charge the connected device when the unit is in Standby mode.
10
TROUBLESHOOTING GUIDE
Check the followings before requesting service
SYMPTOM
POSSIBLE CAUSE
POSSIBLE SOULTION
No power
AC plug not connected to the
wall outlet
Plug to the wall outlet.
Volume in minimum position
Raise volume level by pressing the VOL
(Volume) + button
No sound
Sound distortion
Remote not
working
Bluetooth
reception failure
The connected device is not
in payback mode
Play the music/movie in the connected
device as usual and make sure the
volume level of it is in high level
Input source incorrect
Press the SOURCE button repeatedly to
set the input source to the desired mode
Bass level of the connected
device too high
Reduce the bass level of the connected
device
Volume level too high
Reduce the volume level by pressing
the VOL (Volume ) - button
The batteries are consumed
Replace with new battery
The external device is far from
the unit
Put the external BT device close to the
unit
Have not paired
Pair both unit as BT pairing page
11
GENERAL SPECIFICATIONS
Power Source...........................................................................................................AC 120V~60Hz
Power Consumption...................................................................................................................45W
Radio Coverage................................................................................................FM 87.5 -108.0 MHz
Impedance of Speakers :
Loud Speakers ....................................................................................................... 8 Ohm, 10W x 2
Tweeters................................................................................................................... 8 Ohm, 5W x 2
Bluetooth working distance......................................................................................... Up to 30 feet
(Measured in open area. Wall and structures may affect the effective range.)
Remote working distance.............................................................................................Up to 15 feet
USB port output ..............................................................................................DC
5V, Max. 2.1A
Accessories
1 x User Manual
1 x Remote Control, using CR 2025 button cell (Already installed in the remote control)
1 x Stereo Audio Connection Cable with 3.5mm stereo plug
4 x Assembly Screws / Washers
2 x Wooden Bases
1 x Plastic Holder
12
LIMITED WARRANTY
Craig warrants this product to be free from manufacturing defects in material and
workmanship under normal use for a period of 90 days from date of purchase. If service
is required, please return the product to the store where it was purchased for exchange;
or, pack the unit in the original packing material with all accessories if applicable, a copy
of your sales receipt and a Cashier’s check or Money Order for $20.00 (to cover shipping
and handling costs) payable to Craig Electronics Inc. For consumers in Canada, please
make sure that the cashier check or money order is redeemable through a U.S. bank.
Ship your product freight pre-paid. Your unit will be repaired, replaced or if the unit can
not be repaired or replaced, a refund will be forwarded to you within four weeks of receipt
of your unit. Please ship your unit to:
Craig Electronics Inc.
1160 NW 163 Drive
Miami, Fl 33169
This warranty is void if the product has been: a) Used in a commercial application or
rental. b) Damaged through misuse, negligence, or abuse. c) Modified or repaired by
anyone other than an authorized Craig service center. d) Damaged because it is
improperly connected to any other equipment.
Note: This warranty does not cover: a) Ordinary adjustments as outlined in the Owner’s
Manual which can be performed by the customer. b) Damage to equipment not properly
connected to the product. c) Any cost incurred in shipping the product for repair. d)
Damage to the product not used in the USA.
This warranty is not transferable and only applies to the original purchase. Any implied
warranties, including the warranty of merchantability, are limited in duration to the period
of this expressed warranty and no warranty whether expressed or implied shall apply to
the product thereafter.
Under no circumstance shall Craig be liable for any loss or consequential damage arising
out of the use of this product. This warranty gives specific legal rights. However, you may
have other rights which may vary from state to state. Some states do not allow limitations
on implied warranties or exclusion of consequential damage. Therefore, these
restrictions may not apply to you.
To Obtain Service on your Product
email:service@craigelectronics.com
Printed in China
CHT910-IB-E0CL1-B0US

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Creation Date--Text             : 
Producer                        : Corel PDF Engine Version 14.0.0.653
Mod Date--Text                  : 
Format                          : application/pdf
Creator                         : Administrator
Title                           : CHT910.cdr
Creator Tool                    : CorelDRAW
Modify Date                     : 2012:12:04 14:20:04+08:00
Metadata Date                   : 2012:12:04 14:20:04+08:00
Document ID                     : uuid:cb39e346-47d6-479b-b32d-df1ba4edad9c
Instance ID                     : uuid:3340d24b-d14b-4906-9ba8-073e77f5ff7d
Has XFA                         : No
Page Count                      : 14
Create Date                     : D:20111224062044Z
Author                          : Administrator
EXIF Metadata provided by EXIF.tools
FCC ID Filing: OKUCHT914N

Navigation menu