Junlan Electronic CHT914N HOME THEATER SPEAKER SYSTEM WITH BLUETOOTH User Manual CHT910
Shenzhen Junlan Electronic Ltd HOME THEATER SPEAKER SYSTEM WITH BLUETOOTH CHT910
user manual
TOWER STEREO SYSTEM
TOWER STEREO SYSTEM
Owner's Manual
PLEASE READ BEFORE OPERATING THIS EQUIPMENT.
Model: CHT914n
IMPORTANT SAFETY INSTRUCTIONS
Insert the AC plug into a conveniently located AC outlet having AC 120V~60Hz.
NOTE: The AC plug supplied with the unit is polarized to help minimize the
obsolete outlet.
possibility of electric shock. If the AC plug dose not fit into a non polarized
AC outlet, do not file or cut the wide blade. It is the user's responsibility to
have an electrician replacing the
1. Plastic Holder
2. Remote Sensor
3. Speakers
4. Speaker Net
5. Wooden Base
6. Washers
1
2
3
5
6
7
3
7. Screws
MAIN UNIT-- RIGHT CHANNEL SPEAKER
1
LEFT CHANNEL SPEAKER
4
5
3
1
1. Speakers
2. Speaker Net
3. Wooden Base
4. Screws
5. Washers
Note:
1. Assemble the wooden base to the main body with the supplied screws and washers as Fig. 2 & 4 above.
2.The speaker net can be taken out and reassembled as Fig.1 & 3 above.
Figure 3
2
4 Figure 4
Figure 2
Figure 1
i
Figure 5
3.Install the
Plastic Holder
i
External Device
Plastic Holder on the top of unit to hold the external device as Fig. 5 above.
POWER SOURCE
INSTALLATION
7. /
(Play/Pause) button
8.
TUNE - button
9. AUX IN 2 jack
10.
11. SOURCE indicator
1. USB Port (For recharge only)
2.
3. STANDBY indicator
4. SOURCE button
5.
/ TUNE + button
VOL- (Volume Down) button
6. VOL+ (Volume Up) button 12.
13. AUX IN 1 jacks
14. FM Antenna
(Power) button
12
13
14
1
2
3
9
4
5
6
7
8
10
11
MAIN UNIT
Speaker Connector
(For Left Channel Speaker)
LOCATION OF CONTROLS
1
2
3
4
5
6
7
8
REMOTE CONTROL
1. POWER button
2. /TUNE - button
3. VOL (Volume)+/- buttons
4. SOURCE button
5. (Mute) button
6. / TUNE+ button
7 (Play/Pause) button
8 EQ (Equalizer) button
7
LOCATION OF CONTROLS
Fig.1 Fig.2 Fig.3
BATTERY PRECAUTIONS
EFFECTIVE DISTANCE OF REMOTE TRANSMITTER
Approx.15 feet
-First Time Use
Remove and discard the insulation tab as figure on the right
-Replacing Batteries For Remote Control
1. Push and slide out the battery holder as figure 1 below.
2. Replace the battery with a new CR2025 button cell as the
polarity markings on the rear of the Remote Control.
3. Close the battery holder.
.
Remote Sensor, on
the front of main unit
BATTERY INSTALLATION--- REMOTE CONTROL
7
GENERAL OPERATIONS
LEFT SPEAKER CONNECTION
Black wire
Red wire
Main Unit Left Speaker
Connect the connection wires (Red and Black) from Left Speaker to the Speaker Connectors
on the rear of Main Unit as the figure above.
1.Insert the AC Power Cord into conveniently located AC outlet having AC 120V~60Hz.The Red
Standby Indicator will light.
2.Press Power button on the Unit or Remote Control to power on the unit. The Red Standby
Indicator will turn off and source Indicator will light.
corresponding color as below:
3.Press the SOURCE button repeatedly to switch to desired mode.The source Indicator will turn
to
~ Green: Radio
~ Blue: Bluetooth
~ Purple: AUX IN 1
~ Orange: AUX IN 2
4.During Playback:
~ Press the VOL (Volume) buttons to adjust volume level as desired.
~ Press EQ button repeatedly to select and set equalizer mode as desired.
~ Press (Mute) button on the Remote Control to turn off the sound. Press again to resume.
5.When finished listening, press Power button to power off the unit. The source Indicator will
turn off and Red Standby Indicator will light.
wall outlet if a long period of time will not use.
NOTE:
For saving energy, unplug the Power AC Cord from
FM Antenna
LISTEN TO FM RADIO
1.Power ON the unit as previous procedures.
2.Press the SOURCE button repeatedly until the color of source Indicator turns Green.
4.Repeat the same procedures until the desired radio station is received.
NOTE: If the received FM station is in stereo mode, the unit will play it in stereo mode automatically.
3.Press and hold the /TUNE - or /TUNE + buttons until the source Indicator start blinking.
The unit will start to search next (or previous) available FM radio station then plays.
The Antenna wire on the rear of Main Unit is for radio reception. If reception is weak, unwind and
extend the wire or relocate the wire to improve the radio reception.
MP3 Player; Discman ... etc.).
White
Red
LISTEN TO TV/DVD/VCR/DVR
X IN 1
Audio out jacks on
TV/DVD/ VCR/DVR
DVD
R
L
AUX IN 1
N 1
4. Press SOURCE button repeatedly until the indicator turns Purple.
1. Connect one end of RCA audio connection cable (not supplied) to the AUX IN 1 jacks on the rear
of the unit as the figure above.
2. Connect the other end to the AUX out jacks on the external player (such as Television, VCR, DVD
Player, DVR ... etc.).
5. Play the music in the external player as usual. (Make sure the volume output level of the player is
in high level. Otherwise, sound from this unit is weak).
8
3. Power on the unit as previous procedures.
9
3. Power on the unit as previous procedures.
4. Press the SOURCE button repeatedly until the color of source Indicator turns Orange.
1. Connect one end of supplied audio connection cable to the AUX IN 2 jack on the top of the unit.
2. Connect the other end to the AUX out/Line out/Phone jack on the external player (such like iPod,
iPhone, iPad, MP3 Player, Discman... etc.).
5. Play the music in the external player as usual. (Make sure the volume output level of the player
is in high level. Otherwise, sound from this unit is weak).
as the figure above.
LISTEN TO EXTERNAL AUDIO DEVICES
AUX IN 2 jack
10
BLUETOOTH PARING AND PLAYBACK
1. Power on the unit as previous procedures.
2. Press the SOURCE button on the unit or remote control until the indicator turns blue.
3. Turn on the BT function on the external BT device and play the music as usual. (Make sure
the volume level of the external BT device is set to high level).
4. During palyback:
Press the VOL (Volume) +/- buttons to adjust volume level.
Press the / TUNE- or / TUNE + button to skip track.
Press the (Play/Pause) button to pause. Press again to to resume normal playback.
NOTES:
1. During the first time use, pair the external BT device as below:
A. Power on the unit as previous procedures and press the SOURCE button repeatedly until the
indicator turns blue and blinking.
B. Power on the external BT device and enter searching mode. Start paring as the on screen
instructions on the external BT player(For detailed paring procedures, please refer to
the user's manual of your BT device.)
C. When the external BT player searched the Speaker, our model number"CHT914n" will
appear on the display of the external BT device. Paring code"0000" may need to enter.
The USB port in this unit is for recharge only. Recharge the USB device as below:
2. Insert the full size USB Plug from the USB connection cable to the USB port on the top of unit.
3. Charging will start automatically.
4. When finished, disconnect the full size USB Plug from the unit.
You can also charge the connected device when the unit is in Standby mode.
1. Connect the small plug from the USB connection cable to the device as usual. (Connection cable
not supplied).
NOTES:
The maximum output from the USB port is DC 5V, 2.1A. You can change any rechargeable USB
devices charging current less than it, such like IPod, IPhone, IPad, MP3 Player … etc.
USB PORT
11
Check the followings before requesting service
SYMPTOM POSSIBLE CAUSE POSSIBLE SOULTION
No power AC plug not connected to the
Plug to the wall outlet.
No sound
Volume in minimum position Raise volume level by pressing the VOL
(Volume) + button
The connected device is not
in payback mode
Play the music/movie in the connected
device as usual
Input source incorrect
wall outlet
Sound distortion
Volume level too high VOL (Volume ) - button
Reduce the bass level of the connected
Reduce the volume level by pressing
the
Bass level of the connected
device too high device
Bluetooth
reception failure
The external device is far from
the unit
Have not paired Pair both unit as BT pairing page
TROUBLESHOOTING GUIDE
Remote not The batteries
are consumed Replace with new battery
working
desired mode.
Press the SOURCE button repeatedly to
set the input source to the desired mode
Put the external BT device close to the
unit
and make sure the
volume level of it is in high level
12
Power Source...........................................................................................................AC 120V~60Hz
Radio Coverage................................................................................................FM 87.5 -108.0 MHz
Remote working distance.............................................................................................Up to 15 feet
Impedance of :
Loud .......................................................................................................8 Ohm, 10W x 2
Tweeters................................................................................................................... 8 Ohm, 5W x 2
Bluetooth working distance......................................................................................... Up to 30 feet
(Measured in open area. Wall
and structures may affect the effective range.)
1 x User Manual
1 x Remote Control, using CR 2025 button cell (Already installed in the remote control)
1 x Stereo Audio Connection Cable with 3.5mm stereo plug
4 x Assembly Screws / Washers
Accessories
2 x Wooden Bases
1 x Plastic Holder
Power Consumption...................................................................................................................45W
USB port output ..............................................................................................DC 5V, Max. 2.1A
Speakers
Speakers
GENERAL SPECIFICATIONS
Craig warrants this product to be free from manufacturing defects in material and
workmanship under normal use for a period of 90 days from date of purchase. If service
is required, please return the product to the store where it was purchased for exchange;
or, pack the unit in the original packing material with all accessories if applicable, a copy
of your sales receipt and a Cashier’s check or Money Order for $20.00 (to cover shipping
and handling costs) payable to Craig Electronics Inc. For consumers in Canada, please
make sure that the cashier check or money order is redeemable through a U.S. bank.
Ship your product freight pre-paid. Your unit will be repaired, replaced or if the unit can
not be repaired or replaced, a refund will be forwarded to you within four weeks of receipt
of your unit. Please ship your unit to:
Craig Electronics Inc.
1160 NW 163 Drive
Miami, Fl 33169
This warranty is void if the product has been: a) Used in a commercial application or
rental. b) Damaged through misuse, negligence, or abuse. c) Modified or repaired by
anyone other than an authorized Craig service center. d) Damaged because it is
improperly connected to any other equipment.
Note: This warranty does not cover: a) Ordinary adjustments as outlined in the Owner’s
Manual which can be performed by the customer. b) Damage to equipment not properly
connected to the product. c) Any cost incurred in shipping the product for repair. d)
Damage to the product not used in the USA.
This warranty is not transferable and only applies to the original purchase. Any implied
warranties, including the warranty of merchantability, are limited in duration to the period
of this expressed warranty and no warranty whether expressed or implied shall apply to
the product thereafter.
Under no circumstance shall Craig be liable for any loss or consequential damage arising
out of the use of this product. This warranty gives specific legal rights. However, you may
have other rights which may vary from state to state. Some states do not allow limitations
on implied warranties or exclusion of consequential damage. Therefore, these
restrictions may not apply to you.
To Obtain Service on your Product
email:service@craigelectronics.com
LIMITED WARRANTY
Printed in China CHT910-IB-E0CL1-B0US