Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 743323 |
| Application ID | 0vGYo9aU45Hx19xzLTv4bg== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 39.62kB (495195 bits) |
| Date Submitted | 2007-01-02 00:00:00 |
| Date Available | 2007-01-02 00:00:00 |
| Creation Date | 2007-01-02 13:58:22 |
| Producing Software | Acrobat Distiller 7.0 (Windows) |
| Document Lastmod | 2007-01-02 13:58:52 |
| Document Title | Microsoft Word - 1883user manual.doc |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | celia.tseng |
USER MANUAL Bluetooth Module / APM1883 TABLE OF CONTENTS 1. FCC Statement ………………………………………………………………….…….2 2. Description…………………………………………………………….……………….3 3. Set Steps……………………………………………………………………………….6 4. PIN ASSIGNMENT.…………………………………………………….……………..7 4.1 PIN DEFINITION………………………………………………………………….7 4.2 MAJOR COMPONENT LIST……………………………………………………10 5. SYSTEM SPECIFICATION………………………………………………………….12 5.1 ABSOLUTE MAXIMUM RATING……………………………………………….12 5.2 RECOMMENDED OPERATING CONDITION………………………………..13. 6. ELECTRICAL CHARACTERISTICS……………………………………………….13 6.1 I/O SPECIFICATION…………………………………………………………….13 6.2RF SPECIFICATION TEST SUMMARY……………………………………………..14 6.3 CURRENT CONSUMPTION TEST…………………………………………………..15 6.4 AUDIO SPECIFICATION………………….……………………………………16 7. LED STATUS…………………………………………………………………………16 8. CONNECTION (INQUIRY/PAIRING) TIME…………………………….…………16 9. ORDERING INFORMATION……………………………………………….………16 10. OUTLINE DRAWING………………………………………………………..………17 10.1 MAIN BOARD (FRONT SIDE)…………………………………..……………18 10.2 MAIN BOARD(BACKSIDE)…………………………………………………...18 10.3 CONNECTIOR DRAWING……………………………………………………19 11. FCC TO OEM installer…………………….………………….……………………..22 12. Label………………………..…………………………………………………………23 FCC Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Notice: Any changes or modification not expressly approved by the party responsible could void the user’s authority to operate the device. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undersired operation. The Bluetooth Module allows a speakers with a communicate with other Bluetooth-enabled devices. When used with the Bluetooth application software, it can perform wireless network application such as information exchange, file transfer, network access, dial-up networking, headset audio gateway, and so on. General Description The apm1883 Bluetooth audio transceiver provides off-the-shelf wireless function for class1 and class2 stereo audio application. It consists of apm1882 Bluetooth audio module, PA/LNA, RF switch and LPF with a compact size of 45mm by 26mm for class1 solution. The apm1882 integrates Broadcom’s ZV4301 Bluetooth chip, Wolfson’s WM8731 CODEC, crystal and Flash memory on a single module. It could be easily embedded into audio system for Bluetooth wireless communication. The specified profiles and firmware are pre-loaded into the built-in flash memory of apm1882 module for Bluetooth audio transmission and receiving. The user could update the firmware version by using the UART interface test point connect to host PC. Features �Compact size class1 and class2 Bluetooth audio transceiver: 45×26mm. �Integrate apm1882 Bluetooth audio module, PA/LNA, RF switch and LPF into one board for class1 solution. �Compliant with Bluetooth specification V1.2. �Low power modes available �Easy to embed in Bluetooth audio System �Class1 performance (with PA/LNA) RF output power: < +20 dBm Receiver sensitivity: 85dBm @0.1%BER �Class2 performance (without PA/LNA) RF output power: < +4 dBm Receiver sensitivity: 80dBm @0.1%BER Applications � AV equipments � Bluetooth stereo headphone or speaker which supports audio source switch between stereo music and cellular phone call � Bluetooth audio adaptor to transmit music from an analog source Functional Block Diagram Revision History Date Release Author 29Jun06 1.0 Yushin/Baron Description Initial release 3. Setup Steps Providing 5V to DC power J5 For LED indication please connect to J3 For remote control please using J6 For microphone input please connecting J4 For speaker use please connecting audio out to J1(BDB88312A1RX, BDB88322A1RX only) For audio transmit please connecting audio in to J2 (BDB88312A1TX, BDB88322A1TX only) IPEX1 is RF cable connector and is used for BDB88312A1TX, BDB88312A1RX IPEX2 is RF cable connector and is used for BDB88322A1TX, BDB88322A1RX 4. Pin Assignment (Top View) (Bottom View) IPEX 1 For Class 1 3.6mm U9 For Class 1 J5 DC Power Input DC Test Point IPEX 2 For Class 2 J3 VCC 5V RF Test Point For Class 1 GND RF Test Point For Class 2 LED UART Test Point U10 J6 UCTS URTS UTXD URXD GPIO Pin J4 MIC Input For Receiver J1: Headphone Output For Receiver J2: Audio Line In For Transmitter : Connector & Device Pin 1 mark 4.1 Pin Definition (J1): Headphone Output Connector Pin # Pin Name LHPOUT AGND Type Analogue Output Ground Description Left Channel Headphone Output Analogue GND Pin # Pin Name Type Description Right Channel Headphoe Output RHPOUT Analogue Output (J2): Audio Line IN Connector Pin # Pin Name LLINEIN AGND RLINEIN Type Analogue Output Ground Analogue Output Description Left Channel Line Input Analogue GND Right Channel Line Input (J3):LED Connector Pin # Pin Name Type Description LED- Supply LED cathode LED+ Supply LED anode (J4):Microphone Connector Pin # Pin Name Type GND Ground MIC Analogue Input Description Analogue GND Microphone input (J5):VCC5V Connector Pin # Pin Name Type Description VCC5 Supply +5V input power GND Ground Analogue GND (J6):GPIO Pin Pin # Pin Name Type Description Pin # Pin Name Type BACK(GPIO9) Digital I/O FORWARD(GPIO10) Digital I/O PLAY/PAUSE(GPIO6) Digital I/O ACC/REJ(GPIO14) Digital I/O GPIO15 Digital I/O GND Ground Description Internal pull-high to 3.3V through 10K resistor, active low Internal pull-high to 3.3V through 10K resistor, active low Need to external pull-high to 3.3V through 10K resistor, active low Internal pull-high to 3.3V through 10K resistor, active low. For other application, need to external pull-high to 3.3V through 10K resistor.. Digital GND (J2): Audio Line IN Connector Pin Pin Name LLINEIN AGND RLINEIN Type Analogue Output Ground Analogue Output Description Left Channel Line Input Analogue GND Right Channel Line Input (J3): LED Connector Pin Pin Name Type Description LED Supply LED cathode LED+ Supply LED anode (J4): Microphone Connector Pin Pin Name Type GND Ground MIC Analogue Input Description Analogue GND Microphone input (J5): VCC5V Connector Pin Pin Name Type Description VCC5 Supply +5V input power GND Ground Analogue GND (J6): GPIO Pin Pin Pin Name Type BACK(GPIO9) Digital I/O FORWARD(GPIO10) Digital I/O PLAY/PAUSE(GPIO6) Digital I/O ACC/REJ(GPIO14) Digital I/O GPIO15 Digital I/O GND Ground Description Internal pullhigh to 3.3V through 10K resistor, active low Internal pullhigh to 3.3V through 10K resistor, active low Need to external pullhigh to 3.3V through 10K resistor, active low Internal pullhigh to 3.3V through 10K resistor, active low. For other application, need to external pullhigh to 3.3V through 10K resistor.. Digital GND *Based on customer’s different demand, the GPIO could be modified for different function. 4.2 Major Component List (U9): Atmel Front End IC Pin # Pin Name Type Description 10 1 LNA_OUT Analogue Output RX_ON I/O RX active high PU I/O Powerup active high R_SWITCH I/O Resistor to GND sets the PIN diode SWITCH_OUT GND LNA_IN GND Ground Digital GND VS_LNA Supply Supply voltage for LNA 10 GND Ground Analogue ground 11 V3_PA_OUT 12 V3_PA_OUT 13 V3_PA_OUT 14 GND 15 RAMP I/O 16 V2_PA Supply Inductor to power supply for power amplifier 17 V2_PA Supply Inductor to power supply for power amplifier 18 GND Ground Analogue ground 19 V1_PA Supply Supply voltage for power amplifier 20 PA_IN Analogue input Analogue Output Ground Analogue Input Analogue output Low noise amplifier output Switched current output for PIN diode Analogue ground Low noise amplifier input Inductor to power supply for power amplifier output Analogue output Inductor to power supply for power amplifier output Analogue output Ground Inductor to power supply for power amplifier output Analogue Ground Power ramping control input Power amplifier input (U10): apm1882 Audio Module Pin # Pin Name Type Description GPIO10 Digital I/O General Purpose I/O GPIO9 Digital I/O General Purpose I/O UART_RTS Digital Output UART_CTS Digital Input PA_CTRL Digital Output PA Control for Class1 Application UART_TXD Digital Output Transmit Data UART_RXD Digital Input Receive Data GND Ground Request to Send (active low) Clear to Send (active low) Digital GND 11 9 ANT RF I/O 50 Ohm Rx/Tx Connection to Antenna 10 GND Ground Digital GND Pin # Pin Name Type Description 11 GPIO11 Digital I/O General Purpose I/O 12 GPIO12 Digital I/O General Purpose I/O 13 INT_0 Digital Input External interrupt [0] 14 VDD_USB Supply USB VDD 15 VDD_ DIG Supply Bluetooth Digital VDD 16 GPIO13 Digital I/O General Purpose I/O 17 GPIO14 Digital I/O General Purpose I/O 18 GPIO15 Digital I/O General Purpose I/O 19 GND Ground Digital GND 20 GND Ground Digital GND 21 GND Ground Digital GND 22 MODE 23 GND Ground Digital GND 24 VCC Supply Flash Memory VCC 25 GPIO0 Digital I/O 26 DVDD Supply CODEC Digital Core VDD 27 AVDD Supply CODEC Analogue VDD 28 LHPOUT Analogue Output Left Channel Headphone Output 29 RHPOUT Analogue Output Right Channel Headphone Output 30 MICBIAS Analogue Output Electric Microphone Bias 31 AGND Ground 32 MICIN Analogue Input Microphone Input (AC Coupled) 33 RLINEIN Analogue Input Right Channel Line Input (AC Coupled) 34 LLINEIN Analogue Input Left Channel Line Input (AC Coupled) 35 VDD_ANG Supply Bluetooth Analog VDD 36 VDD_VCO Supply Bluetooth VCO VDD 37 VDD_RF Supply Bluetooth RF VDD 38 RESET Digital Input Digital Input Mode Selection (16Mbit Flash Memory A19 Selection) General Purpose I/O (12MHz test point) Analogue GND Reset Input (Active Low for 5 ms); Schmitt Triggered 12 39 GPIO6 40 GND Digital I/O General Purpose I/O Ground Digital GND 5 System Specification 5.1 Absolute Maximum Rating Symbol Description Min. Typ. Max. Units Storage temperature 40 +105 °C VCC5 apm1883 DC Power Input 3.6 8.0 Volts AVDD CODEC analogue VDD 0.3 3.63 Volts *Absolute maximum ratings indicate limits beyond which damage to the device may occur. 5.2 Recommended Operating Condition Symbol VCC5 Description Min. Operating temperature 25 apm1883 DC Power Input 3.6 Typ. Max. Units +85 °C 8.0 Volts Max. Units 0.8 Volts 5.5 Volts 0.4 Volts 6 Electrical Characteristics 6.1 I/O Specification (Operation Temp.=25°C, VCC=3.3V ) Symbol Description/ Test Conditions VIL Input low voltage VIH Input high voltage VOL Output low voltage IOL =2mA VOH Output high voltage IOH =2mA Min. 2.0 2.4 Typ. Volts 13 IOL Output low current VOL =0.4V 2.2 mA IOH Output high current VOH =2.4V 3.1 mA +1 Volts II Input leakage current RINLINE Line in input resistance CINLINE Line in input capacitance RINMIC CINMIC PO VI=3.3V or 0V 0dB gain 20k 30k Ohms 12dB gain 10k 15k Ohms 10 pF 10k Ohms 10 pF RL=32 Ohms 30 mW RL=16 Ohms 50 mW Microphone input resistance Microphone input capacitance Headphone output power 62 RF Specification Test Summary (Operation Temp.=25°C, VCC=3.3V) Parameter Min Class Maximum RF transmit power Class Typ Max Bluetooth Spec. Unit Results +18 0 to +20 dBm Pass +2 6 to +4 dBm Pass kHz Pass 140 165 Modulation index: �f2max 115 172 > 115 kHz Pass Modulation index: �f2avg / �f1avg 0.8 1.04 > 0.8 NA Pass Initial carrier frequency accuracy 20 + 75 kHz Pass Carrier frequency drift rate 11 20 < 20 kHz/50us Pass 16 21 + 25 kHz Pass 11 25 + 40 kHz Pass 18 25 + 40 kHz Pass Carrier frequency drift: one slot packet Carrier frequency drift: three slot packet Carrier frequency drift: five slot packet 175 140 < �f1avg < Modulation index: �f1avg 175 14 Class Sensitivity – single slot packets Class Class Sensitivity – multi slot packets Class Maximum usable signal 20 85 < 70 dBm Pass 80 < 70 dBm Pass 85 < 70 dBm Pass 80 < 70 dBm Pass > 20 dBm Pass 6.3 Current Consumption test (Operation Temp.=25°C, VCC=3.3V) Transmitter Application Mode Average Maximum Units Class 1 105 mA Class 2 17 mA Transmit DH(1,3,5) packets with PRBS9 Class 1 220 300 mA payload (Transmitter) Class 2 86 120 mA Average Maximum Units Inquiry state Headphone Application Mode Class 1 17 mA Class 2 17 mA Tester sends DH1 packets with PRBS9 Class 1 98 150 mA payload to EUT Class 2 90 120 mA Inquiry scan 6.4 Audio specification Parameter Min Typ Max Unit 15 Sample rate 48 kHz Noise level 60 dBA DC input level 3.3 Input signal level Frequency 20 response Vrms 1k 20k Hz S/N ratio 90 dB Separation 90 dB 0.8 mV Hum & Noise level 7 LED Status Operating State Inquiry scan Data throughput LED Blink Frequency Fast mode 10 Hz Slow mode 1.5 Hz 8. Connection (Inquiry/Pairing) Time Operating State Typical Maximum Units To connect a headset in first time 120 Sec. To connect original headset after disconnection Sec. To connect different headset after disconnection 120 Sec. 16 9 Ordering Information Part Number Description BDB88312A1TX Transmitter for class 1 application BDB88312A1RX Receiver for class 1 application BDB88322A1TX Transmitter for class 2 application BDB88322A1RX Receiver for class 2 application 10 Outline Drawing 10.1 Main Board (Front Side) 17 *Physical dimension unit in mm 10.2 Main Board (Backside) 18 *Physical dimension unit in mm 10.3 Connector Drawing 19 20 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the distance between the equipment and the receiver. Connect the equipment to outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Information for OEM integrator The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user manual of the end product. The user manual which is provided by OEM integrators for end users must include the following information in a prominent location. “To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” Label for end product must include “ Contains FCC ID: SETAPM1883 ” or “ A RF transmitter inside, FCC ID: SETAPM1883 ”. TO OEM installer: 1. FCC ID label on the final system must be labeled with “Contains FCC ID: 21 SETAPM1883” 2. In the user manual, final system integrator must be ensure that there is no instruction provided in the user manual to install or remove the speakers. 3. Audio module must be installed and used in strict accordance with the manufacturer’s instruction as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards. The user manual of the final host system must contain the following statements: USA-Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the distance between the equipment and the receiver. Connect the equipment to outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 22 Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Caution: Exposure to Radio Frequency Radiation. This device must not be co-located or operating in conjunction with any other antenna or transmitter. 12. Label FCC IDENTIFIER： SETAPM1883 Name of Grantee： Juster Co., Ltd. Equipment Class： Part 15 Bluetooth Module 23
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 (Windows) Create Date : 2007:01:02 13:58:22+08:00 Creator Tool : PScript5.dll Version 5.2 Modify Date : 2007:01:02 13:58:52+08:00 Metadata Date : 2007:01:02 13:58:52+08:00 Format : application/pdf Title : Microsoft Word - 1883user manual.doc Creator : celia.tseng Document ID : uuid:fa1c5d4e-f0df-4705-a5c2-5bd05c56a6b5 Instance ID : uuid:32ae2ad7-2954-4115-9d78-8ab07311abe1 Page Count : 23 Author : celia.tsengEXIF Metadata provided by EXIF.tools