KAB Enterprise TR-022 Remote Controller User Manual RC 019 TR 022 20150819

Kab Enterprise Co., Ltd. Remote Controller RC 019 TR 022 20150819

User Manual

Indoor Wireless Remote ControlOperating InstructionsWhen using electrical products, always follow basic safety precautions including the following:IMPORTANT SAFEGUARDS Signal Word Definitions NOTE: These are general definitions only; all may not pertain to the actual product purchased. DANGER – Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. Usage of this signal word is limited to themost extreme situations. WARNING – Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION – Indicates a potentially hazardous situation, which, if not avoided, may result in minor/moderate injury or product/property damage. It also alerts against unsafe practices.READ ALL INSTRUCTIONS BEFORE USE. WARNING:To reduce the risk of fire, electric shock, or serious personal injury • Do not immerse the product in liquids• This product is not intended for use by children and contains small parts that may pose a choking hazard to children under the age of three. Keep the product out of the reach of children and pets.• Do not use an electrical device or appliance with this product whose electrical specifications exceed those specified in the “Electrical Specifications” section of this manual.CAUTION:To reduce the risk of personal injury or product/ property damage:• This product is intended for non-commercial, non-industrial use in the remote control of single electrical outlet. Do not use this product for any other purpose.Set Up1. Plug the receiver into a standard 125-volt AC electrical outlet.2. Confirm that the electrical specifications of an item you wish to use with this product do not exceed those specified in the "Electrical Ratings" section. Plug the item into an outlet of the receiver.3. Remove the plastic battery tab from the battery compartment in the back of the remote control to activate the 3V lithium pre-installed battery.Item: RC-019/TR-022ELECTRICAL RATINGS Range Up to 120ft.125Vac 60Hz 15 A General Purpose 125Vac 60Hz 15 A Resistive1,000 W Tungsten 500 VA Electronic Ballast120Vac 60Hz 8.3A Ballast.1/2 HP 1. To set up the receiver (outlet) with connecting device.2. To activate the Receiver, press the ‘ON’ Button of the Remote Control. The red LED of the Remote Control will illuminate momentarily and the LED of the Receiver will remain illuminated.3. To turn the Receiver OFF, press the ‘OFF’ Button of the Remote Control. The LED on the receiver will shut off.TO USEBattery Handling and UsageWARNING: Keep batteries away from children and pets. • Follow the battery manufacturer’s safety and usage instructions. • Insert the battery observing the proper polarity (+/−) as indicated inside the Battery Compartment. CAUTION: Failure to properly align the battery polarity can cause personal injury and /or property damage. • Remove a spent or discharged battery from the product. Remove the battery when not using the product for an extended period. • Never throw batteries into a fire. Do not expose batteries to fire or other heat sources.• Dispose or recycle spent/discharged batteries in compliance with all applicable laws. For detailed information, contact your local solid waste authority. • Battery contains mercury. Do not put in trash. Recycle or manage as hazardous waste.This equipment has been tested and found to comply with the limits for Class B digital device, harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Federal Communication Commission Interference StatementSAVE THESE INSTRUCTIONS! Made in ChinaThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device.FCC Caution: Any changes or modifications not expressly approved by the partyresponsible for compliance could void the user's authority to operate this equipment.Battery Replacement: 1. Remove the Battery Compartment Cover from the back of the Remote Control by sliding the Cover in the direction that its treads curve. 2. Remove the spent battery and place a new 3V lithium battery into the Battery Compartment, correctly observing the polarity indications (+/−) inside the Battery Compartment.3. Replace the Battery Compartment Cover. 3V Lithium BatteryRemoteControlReceiversONOFFONOFF3V3V210x220MM

Navigation menu