KAB Enterprise TR-022 Remote Controller User Manual RC 019 TR 022 20150819
Kab Enterprise Co., Ltd. Remote Controller RC 019 TR 022 20150819
User Manual
![](/img.php?id=2779227&img=bg1.png)
Indoor Wireless Remote Control
Operating Instructions
When using electrical products, always follow basic safety precautions including
the following:
IMPORTANT SAFEGUARDS
Signal Word Definitions
NOTE: These are general definitions only; all may not pertain to the actual
product purchased.
DANGER – Indicates an imminently hazardous situation, which, if not avoided,
will result in death or serious injury. Usage of this signal word is limited to the
most extreme situations.
WARNING – Indicates a potentially hazardous situation, which, if not avoided,
could result in death or serious injury.
CAUTION – Indicates a potentially hazardous situation, which, if not avoided,
may result in minor/moderate injury or product/property damage. It also alerts
against unsafe practices.
READ ALL INSTRUCTIONS BEFORE USE.
WARNING:
To reduce the risk of fire, electric shock, or serious personal injury
• Do not immerse the product in liquids
• This product is not intended for use by children and contains small parts that
may pose a choking hazard to children under the age of three. Keep the product
out of the reach of children and pets.
• Do not use an electrical device or appliance with this product whose electrical
specifications exceed those specified in the “Electrical Specifications” section of
this manual.
CAUTION:
To reduce the risk of personal injury or product/ property damage:
• This product is intended for non-commercial, non-industrial use in the remote
control of single electrical outlet. Do not use this product for any other purpose.
Set Up
1. Plug the receiver into a standard 125-volt AC electrical outlet.
2. Confirm that the electrical specifications of an item you wish to use with this
product do not exceed those specified in the "Electrical Ratings" section. Plug
the item into an outlet of the receiver.
3. Remove the plastic battery tab from the battery compartment in the back of the
remote control to activate the 3V lithium pre-installed battery.
Item: RC-019/TR-022
ELECTRICAL RATINGS
Range Up to 120ft.
125Vac 60Hz 15 A General Purpose
125Vac 60Hz 15 A Resistive
1,000 W Tungsten
500 VA Electronic Ballast
120Vac 60Hz 8.3A Ballast.
1/2 HP
1. To set up the receiver (outlet) with connecting device.
2. To activate the Receiver, press the ‘ON’ Button of the Remote Control. The red
LED of the Remote Control will illuminate momentarily and the LED of the
Receiver will remain illuminated.
3. To turn the Receiver OFF, press the ‘OFF’ Button of the Remote Control. The LED
on the receiver will shut off.
TO USE
Battery Handling and Usage
WARNING: Keep batteries away from children and pets.
• Follow the battery manufacturer’s safety and usage instructions.
• Insert the battery observing the proper polarity (+/−) as indicated inside the
Battery Compartment.
CAUTION: Failure to properly align the battery polarity can cause personal injury
and /or property damage.
• Remove a spent or discharged battery from the product. Remove the battery
when not using the product for an extended period.
• Never throw batteries into a fire. Do not expose batteries to fire or other heat
sources.
• Dispose or recycle spent/discharged batteries in compliance with all applicable
laws. For detailed information, contact your local solid
waste authority.
• Battery contains mercury. Do not put in trash. Recycle or manage as hazardous
waste.
This equipment has been tested and found to comply with the limits for Class B digital
device, harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Federal Communication Commission Interference Statement
SAVE THESE INSTRUCTIONS! Made in China
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation of the device.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
Battery Replacement:
1. Remove the Battery Compartment Cover from the
back of the Remote Control by sliding the Cover in
the direction that its treads curve.
2. Remove the spent battery and place a new 3V lithium
battery into the Battery Compartment, correctly
observing the polarity indications (+/−) inside the
Battery Compartment.
3. Replace the Battery Compartment Cover.
3V Lithium Battery
Remote
Control
Receivers
ON
OFF
ON
OFF
3V
3V
210x220MM