KAPSCH TRAFFICCOM CANADA 801660 Transponder User Manual FPT Interior Transponder Mounting Instructions

KAPSCH TRAFFICCOM CANADA INC. Transponder FPT Interior Transponder Mounting Instructions

Contents

Mounting Instructions

Download: KAPSCH TRAFFICCOM CANADA 801660 Transponder User Manual FPT Interior Transponder Mounting Instructions
Mirror Download [FCC.gov]KAPSCH TRAFFICCOM CANADA 801660 Transponder User Manual FPT Interior Transponder Mounting Instructions
Document ID750753
Application IDn2UUxuPvTf7YkefFosnpUw==
Document DescriptionMounting Instructions
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize7.61kB (95123 bits)
Date Submitted2007-01-25 00:00:00
Date Available2007-01-25 00:00:00
Creation Date2006-12-07 10:07:50
Producing SoftwareAcrobat Distiller 6.0 (Windows)
Document Lastmod2006-12-07 10:07:58
Document TitleFPT Interior Transponder Mounting Instructions
Document CreatorAcrobat PDFMaker 6.0 for Word
Document Author: John Wolkowski

MARK IV Industries Corporate, I.V.H.S. Division
®
Short Range Vehicle-to-Roadside Communications Equipment for Automatic Vehicle Identification
G4 Interior Transponder Mounting Instructions
for car interior on windshield
For proper operation, make sure the transponder is mounted as follows:
1. Identify the front face of the transponder. It displays your agency label
and two upward-pointing arrows. (Fig.-1) This side faces the driver with
the arrows pointing toward the roof of your vehicle.
Fig.-1 Transponder Front Face
ARROWS POINT UP
2. Identify the position in your vehicle in which the transponder will be
mounted. The preferred location is between the exposed edge of the
windshield (roofline) and the rear view mirror post—as long as the clearances in Fig.-2 can be maintained. If there is insufficient room, the alternate location shown in Fig.-3 must be used.
3. Having determined the mounting position in your vehicle, clean the inside
surface of that section of the windshield if necessary. Now carefully remove the protective backing from the Dual LockTM mounting strips on the
rear of the transponder as shown in Fig. 4 and firmly press the rear of the transponder against the glass.
Maintain the pressure for about 15 seconds to achieve a good bond.
Fig.-2 Preferred Mounting Location
Fig.-3 Alternate Mounting Location
Fig.-4 Transponder Rear Face
DUAL LOCK STRIPS
PEEL OFF BACKING
MARK IV
FCC ID: JQU801630
This device complies with part 15 of the FCC rules.
Operation is subject to the condition that this device
does not cause harmful interference.
IC: 2665A-801630
UNITED STATES PATENT Nos.
4,870,419; 4,937,581; 5,132,687; 5,164,732
5,192,954; 5,196,846
CANADA PATENT Nos.
1,165,427; 1,248,613
The transponder may be removed by lifting any one corner with sufficient pressure to separate the Dual LockTM
strips. Do not remove the Dual LockTM from the windshield and reuse it; obtain new strips from your service center if necessary.
Rear view mirror
Rev A. 30-Nov-06
801850-001.doc
Transponder
Sh e e t 1 o f 1
© MARK IV INDUSTRIES Corp.
EXCEPT AS MAY BE OTHERW ISE PROVIDED BY CONTRACT, THESE DRAW INGS AND SPECIFICATIONS CONTAIN PROPRIETARY INFORMATION
AND ARE THE PROPERTY OF MARK IV INDUSTRIES LTD. AND ARE ISSUED IN STRICT CONFIDENCE AND SHALL NOT BE TRANSMITTED OR
REPRODUCED OR COPIED OR USED AS THE BASIS FOR MANUFACTURE OR SALE OF APPARATUS W ITHOUT PRIOR W RITTEN PERMISSION.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 1
Language                        : EN-US
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:d9d26143-4126-40fe-a591-c066ed2dee66
Producer                        : Acrobat Distiller 6.0 (Windows)
Comments                        : Revised by RJ Middlemiss June 1998
Company                         : MARK IV Ind., F-P Electronics
Source Modified                 : D:20061207150733
Headline                        : for car interior on windshield
Creator Tool                    : Acrobat PDFMaker 6.0 for Word
Modify Date                     : 2006:12:07 10:07:58-05:00
Create Date                     : 2006:12:07 10:07:50-05:00
Metadata Date                   : 2006:12:07 10:07:58-05:00
Document ID                     : uuid:a66b6d58-8adb-4513-906c-abdbc9ef21ea
Version ID                      : 6
Format                          : application/pdf
Title                           : FPT Interior Transponder Mounting Instructions
Creator                         : John Wolkowski
Description                     : for car interior on windshield
Subject                         : 
Tagged PDF                      : Yes
Author                          : John Wolkowski
EXIF Metadata provided by EXIF.tools
FCC ID Filing: JQU801660

Navigation menu