KMW INTNODEHPV03 Zigbee Module User Manual

KMW INC. Zigbee Module

User Manual

Download: KMW INTNODEHPV03 Zigbee Module User Manual
Mirror Download [FCC.gov]KMW INTNODEHPV03 Zigbee Module User Manual
Document ID3402641
Application IDZAQxcDcuHhev0Jzht0DPfQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize139.09kB (1738564 bits)
Date Submitted2017-05-25 00:00:00
Date Available2017-11-21 00:00:00
Creation Date2017-05-23 20:10:38
Producing SoftwareMicrosoft® Office Word 2007
Document Lastmod2017-05-23 20:12:14
Document TitleUser Manual
Document CreatorMicrosoft® Office Word 2007
Document Author: kmwm71

Document NO.
Project Code
Project Name
Subject
KMWI-A61-E210
L15LT044Z
INNER ANTENNA NODE
Revision NO.
Revised Date
A1
2017.05.02
INNER ANTENNA NODE Manual
Page
Written by
Checked by
Approved by
1 / 14
BJ KIM
INNER ANTENNA NODE
Test Manual
2017. 05. 02.
KN-연-062 (15.12.21)-0
Company Confidential
Document NO.
Project Code
Project Name
Subject
KMWI-A61-E210
L15LT044Z
INNER ANTENNA NODE
Revision NO.
Revised Date
A1
2017.05.02
INNER ANTENNA NODE Manual
Page
Written by
Checked by
Approved by
2 / 14
BJ KIM
 Document Revision History
No
Description
-. initial
KN-연-062 (15.12.21)-0
Author
BJ KIM
Page
REV. NO
A0
Revised
Date
2017. 05. 02
Company Confidential
Document NO.
Project Code
Project Name
Subject
KMWI-A61-E210
L15LT044Z
INNER ANTENNA NODE
Revision NO.
Revised Date
INNER ANTENNA NODE Manual
A1
2017.05.02
Page
Written by
Checked by
Approved by
3 / 14
BJ KIM
INDEX

DOCUMENT REVISION HISTORY ........................................................................................................................ 2
1.
INT NODE TEST AND TEST PROGRAM D/L USING THE POWER SUPPLY 오류! 책갈피가 정의되어 있
지 않습니다.
2.
IQ NXN SETTING.................................................................................................................................................. 6
3.
TX TEST ................................................................................................................................................................. 7
4.
RX TEST ................................................................................................................................................................ 10
KN-연-062 (15.12.21)-0
Company Confidential
Document NO.
Project Code
Project Name
Subject
1.
KMWI-A61-E210
L15LT044Z
INNER ANTENNA NODE
Revision NO.
Revised Date
A1
2017.05.02
INNER ANTENNA NODE Manual
Page
Written by
Checked by
Approved by
4 / 14
BJ KIM
INT NODE TEST AND Test Program D/L Using the Power Supply
INPUT Power
1-1.
INT NODE is powered by a Power Supply. current consumption check using the Power
Supply
Power Supply settings DC15V, 0.5A
INT NODE’s average power consumption is under 0.45W. Current consumption 3mA±1mA
@ 15V
1-2. Change into ISP mode.
1-3. Connect Debug Cable to Z_Deg port(J2). (Use Pogo Pin)
1-4. Execute Device-Programmer MD 2.60 Program.
< Device-Programmer MD 2.60 Execution screen >
1-5.
Select the MG2450/2455.
< Device-Programmer의 Device Setting>
KN-연-062 (15.12.21)-0
Company Confidential
Document NO.
Project Code
Project Name
Subject
KMWI-A61-E210
L15LT044Z
INNER ANTENNA NODE
Revision NO.
Revised Date
A1
2017.05.02
INNER ANTENNA NODE Manual
Page
Written by
Checked by
Approved by
5 / 14
BJ KIM
Open the RF Test Program to download INT
1-6.
MG245X-KMW_IQVIEWER_V22_PA_Rev02.H00
MG245X-KMW_IQVIEWER_V22_PA_Rev02.H01
1-7.
Download only choose H00 file extension.
Download
< Download complete message >
1-8.
Change into Operating Mode
KN-연-062 (15.12.21)-0
Company Confidential
Document NO.
Project Code
Project Name
Subject
KMWI-A61-E210
L15LT044Z
INNER ANTENNA NODE
Revision NO.
Revised Date
A1
2017.05.02
INNER ANTENNA NODE Manual
Page
Written by
Checked by
Approved by
6 / 14
BJ KIM
2. IQ NxN Test Setting
Setting test environment as under figure
PC
TEM CELL
RF
IN/OUT
USB
USB
LAN PORT
IQ nxn
RF CABLE
LAN PORT
RF1
RF2
LAN CABLE
USB CABLE
Block
Diagram
< Test environment image>
2-1. Connect Ethernet cable to Ethernet socket at IQ NXN device rear. Then Check
communication to PC to IQ NXN
< IQ NXN rear >
KN-연-062 (15.12.21)-0
Company Confidential
Document NO.
Project Code
Project Name
Subject
KMWI-A61-E210
L15LT044Z
INNER ANTENNA NODE
Revision NO.
Revised Date
A1
2017.05.02
INNER ANTENNA NODE Manual
Page
Written by
Checked by
Approved by
7 / 14
BJ KIM
2-1. Setting PC's IP as under figure.
< PC의 IP Setting >
2-2.
Execute IQ signal for Zigbee. And Setting Parameter as under figure.
< IQsignal for Zigbee Program Parameter Setting >
A.
3.
Connect USB to Serial Cable to Z_Deg port(J2).
TX Test
3-1.
Connect IQ NXN's RF1 channel to RF output(TEM CELL) using the RF Cable.

KN-연-062 (15.12.21)-0
Company Confidential
Document NO.
Project Code
Project Name
Subject
KMWI-A61-E210
L15LT044Z
INNER ANTENNA NODE
Revision NO.
Revised Date
A1
2017.05.02
INNER ANTENNA NODE Manual
Page
Written by
Checked by
Approved by
8 / 14
BJ KIM
3-2. Execute Tera Term
serial port as under figure.
: The Top bar ‘Setup’ -> ‘Serial Port ...’ selection
< Tera Term’s Serial Port Setting>
Press 'H' key on the keyboard to display the test menu as below..
< KMW TEST MENU >
Press 'C' key on the keyboard and select channel.
< For example selected 11 channel.>
If press 'M' on the keyboard, Tx will be sent Modulation with IFS.
KN-연-062 (15.12.21)-0
Company Confidential
Document NO.
Project Code
Project Name
Subject
KMWI-A61-E210
L15LT044Z
INNER ANTENNA NODE
Revision NO.
Revised Date
A1
2017.05.02
INNER ANTENNA NODE Manual
Page
Written by
Checked by
Approved by
9 / 14
BJ KIM

3-3. Execute Tx test using the ‘IQ signal for Zigbee’ PC Program
Setting Input Parameters as under figure.
RF Input : Left RF PORT
RF Channel : 20/2450MHz (@ Test Ch. 20CH)
- Max Signal Level : 10dBm
- Trigger type : signal trigger
-.Trigger level : -25dBm
- External Atten : 16dB
Measurement Antenna : Flat Type Antenna Coupler (TC-93026A, Maker : TESCOM)
DUT position
Antenna Coupler
TEST FIXTURE
Ant. Coupler 위에 TEST FIXTURE 장착하고
측정할 W-NODE Module올려진 모습
Whistle NODE Module Case와 Ant Coupler 이격거리
< 1.0mm
TEM CELL
KN-연-062 (15.12.21)-0
Air
DUT
Company Confidential
Document NO.
Project Code
Project Name
Subject
KMWI-A61-E210
L15LT044Z
INNER ANTENNA NODE
Revision NO.
Revised Date
A1
2017.05.02
INNER ANTENNA NODE Manual
Page
Written by
Checked by
Approved by
10 / 14
BJ KIM
< Tx test measure >
Compare with the following items to check for defects
Items
Req'd Spec
Remark
Transmit Power (Peak Power)
≥5dBm
[6.9.5]IEEE802.15.4-2006
Spectrum PSD mask
Check
[6.5.3.1]IEEE802.15.4-2006
Transmit Center Frequency Tolerance
±40ppm
[6.9.4]IEEE802.15.4-2006
Error Vector Magnitude
≤35%
[6.9.3]IEEE802.15.4-2006
< Zigbee Rx Test ChecK List>
- RX Test
4-1. Execute 'vector signal analyzer' as under figure.
< Execute
KN-연-062 (15.12.21)-0
Vector signal analyzer >
Company Confidential
Document NO.
Project Code
Project Name
Subject
KMWI-A61-E210
L15LT044Z
INNER ANTENNA NODE
Revision NO.
Revised Date
A1
2017.05.02
INNER ANTENNA NODE Manual
Page
Written by
Checked by
Approved by
11 / 14
BJ KIM
4-2. Connect IQnxn's RF2 Channel to device's output.
Or Change input parameters(Left RF Port-> Right RF Port)
4-3. Open the ‘zigbee_psdu20.mod’ file
Setting
‘A’ section as under figure.
(IEEE802.15.4-2006
≥-85dBm reference : test environment condiction, External Atten 16dB(Loss
offset) -70dBm
4-4. Execute ‘Tera Term’ And then Setting port. ( 3-2. Reference setting Teraterm)
KN-연-062 (15.12.21)-0
Company Confidential
Document NO.
Project Code
Project Name
Subject
4-5.
KMWI-A61-E210
L15LT044Z
INNER ANTENNA NODE
Revision NO.
Revised Date
A1
2017.05.02
INNER ANTENNA NODE Manual
Page
Written by
Checked by
Approved by
12 / 14
BJ KIM
Select RF ON/OFF button as under figure, select 'Start' button. then number 1000's Tx data
is transmitted to the INT NODE Board..

4-2. If press '2' on the keyboard, can be check transmitted result.
< Tera Term Rx count Output Screen >
Compare with the following items to check for defects
Items
Req'd Spec
Receiver Sensitivity
≥-70dBm
Remark
[6.5.3.3]IEEE802.15.4-2006
(≥-85dBm)
Packet Error Rate(1000)
≤1%
Receiver maximum input level
-20dBm
[6.5.3.3]IEEE802.15.4-2006
[6.9.6]IEEE802.15.4-2006

 Specified as ≥-85dBm on IEEE802.15.4-2006, Changed to ≥-75dBm considering that the test environment is
wireless.
KN-연-062 (15.12.21)-0
Company Confidential
Document NO.
Project Code
Project Name
Subject
KMWI-A61-E210
L15LT044Z
INNER ANTENNA NODE
Revision NO.
Revised Date
A1
2017.05.02
INNER ANTENNA NODE Manual
Page
Written by
Checked by
Approved by
13 / 14
BJ KIM
FCC compliance Information
FCC Information to User
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution
Modifications not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
FCC Compliance Information : This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation
Including interference that may cause undesired operation. Modifications not expressly approved by the
manufacturer could void the user’s authority To operated the equipment under FCC rules. To satisfy FCC
exterior labeling requirements, the following text must be placed on the exterior of the end product.
Contains Transmitter Module FCC ID : ORIINTNODEHPV03
CAUTION : This device and its antenna(s) must not be co-located or operated in conjunction with any other
antenna or transmitter. End users cannot modify this transmitter device. Any unauthorized modification could
void the user’s authority to operate this device.
This module is limited to installation in fixed applications, and only installed Lighting Fixture. This module can
not be attached to other device without Lighting device.
IMPORTANT NOTE:
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the
radiator and your body.This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
KN-연-062 (15.12.21)-0
Company Confidential
Document NO.
Project Code
Project Name
Subject
KMWI-A61-E210
L15LT044Z
INNER ANTENNA NODE
INNER ANTENNA NODE Manual
Revision NO.
Revised Date
A1
2017.05.02
Page
Written by
Checked by
Approved by
14 / 14
BJ KIM
This device is intended only for OEM integrators under the following conditions:
1)The transmitter module may not be co-located with any other transmitter or antenna,
2)OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end-product for any additional compliance requirements
required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no longer considered
valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will
be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the
end user regarding how to install or remove this RF module in the user’s manual of the end product which
integrates this module. The end user manual shall include all required regulatory information/warning as
show in this manual.
KN-연-062 (15.12.21)-0
Company Confidential
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Author                          : kmwm71
Create Date                     : 2017:05:23 20:10:38+09:00
Modify Date                     : 2017:05:23 20:12:14+09:00
Language                        : ko-KR
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Microsoft® Office Word 2007
Format                          : application/pdf
Creator                         : kmwm71
Creator Tool                    : Microsoft® Office Word 2007
Metadata Date                   : 2017:05:23 20:12:14+09:00
Document ID                     : uuid:8C3B4BEC-F288-4769-96A3-714C2895B41A
Instance ID                     : uuid:f49ec0a6-0de8-474c-a4e2-c6072b537797
Part                            : 1
Conformance                     : B
Page Count                      : 14
EXIF Metadata provided by EXIF.tools
FCC ID Filing: ORIINTNODEHPV03

Navigation menu