Kaba Mas RINM RFID Reader User Manual InSync Wall Reader 10 17 indd

Kaba Mas LLC RFID Reader InSync Wall Reader 10 17 indd

User Manual

Installation GuideRFID Wall ReaderInstalled withInSync RACRev. A — 10/2017P/N 047 515909Cover
3InSync Wall ReaderInSync Wall Reader Instructions - (All Models)*CAUTION* Wear Safety Glasses While Preparing WallIntroductionThe RFID wall mounted reader provided by dormakaba is compact, lightweight, rugged and water resistant, able to withstand temperatures from -30°F to 150°F (-35°C to 66°C). It is made from durable materials and comes with at least 15 feet (4.6 m) of cable. The reader is capable of functioning up to distances of 500 feet (152.4 m) when powered from the RAC controller board.The reader has a blue LED that indicates that the unit is powered. The reader also provides visual feedback when access is grantedFlush MountSurface MountGang Box MountRegulatory Compliance:This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interf erence, and (2) this device must accept any interference received, including interference that may cause undesired operation.Any changes or modifications of this product, not approved by manufacturer will void the user’s authority to operate the equipment.“ This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.”Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. FCC-Q8SRINMIC-4652A-RINM
4 5InSync Wall Reader InSync Wall ReaderInsync Wall Reader Instructions - (All Models)Instructions1. Use drilling template provided to prepare surface for installation2. Route the wire to the Insync RAC enclosure and connect to the controller board as per the column “RAC Reader Connection” in table 1, or as per Figure B3. Route the other end of the wire through the hole in the mounting plate to the back of the reader and connect as per column “Reader Connection” in table 1 or as per Figure ARAC to Wall Reader ConnectionSignal Reader ConnectionTerminal BlockRAC Wire Color CommentsReader ConnectionGND JP1-2 J1, Pin 2 Black GND+12V JP1-1 J1, Pin3 Red +12VRS485+ JP3-2 J2, Pin 1 + J3, Pin 1* White See NoteRS485- JP3-1 J2, Pin 2 + J3, Pin 2* Green See NoteNote: Jumper cables as shown in Figure B must be connected for the reader to operate correctlyTable 1: Insync RAC and Wall Reader ConnectionsIMPORTANT: The jumper cables supplied with the reader must be connected as shown in Figure B and Table 1 for the contactless reader to operate properly..Figure B. Insync RAC Controller BoardFigure A. InSync Wall ReaderInSync Wall Reader Instructions - (Surface Mount) Mounting ScrewHoles33212Instructions1. Pull cable(s) for RAC through hole in the back plate and, if applicable, through the gasket then screw the mounting plate of the reader to the wall using the screws provided. Use the 1 ⁄" wood screws and inserts for drywall, or use the ⁄" steel screws for mounting on a metal frame2. Connect cables for Insync RAC as per page 4 of this document3. Hook the top of the reader enclosure (item #2) onto the top of the mounting plate (item #3) and secure together with the included screw (item #1), tightened at the bottom of the readerJP1-2 BlackJP1-1 RedJP3-1 GreenJP3-2 WhiteJP1 JP3
6 7InSync Wall Reader InSync Wall ReaderInSync Wall Reader Instructions - (Flush Mount)FIGURE 1132Instructions1. Remove screws (item #1) to remove reader assembly (item #2) from bracket2. Install the drywall bracket on the wall3. Connect cables for Insync RAC as per page 4 of this document4. Install reader (item #2) then faceplate (item #3) using screws (item #1)InSync Wall Reader Instructions - (Gang Box Mount) 12346523451Detail AFIGURE 3Instructions1. Remove screws (item #1) to gain access to reader assembly (item #4)2. Carefully remove reader assembly (item #4) (see warning above) remove protective film from reader face3. Install the gang box with proper screws, not provided4. Connect cables for Insync RAC as per page 4 of this document5. Reader assembly orientation to be as shown on page 3 in Figure A.6. Re-assemble items #1 through #5 in order as shown in detail A, then assemble to gang box (item #6) and tighten screws.
Customer Services & Support800 849 8324General Information:dormakaba.us

Navigation menu