Kaba Mas RINM RFID Reader User Manual InSync Wall Reader 10 17 indd

Download:
Mirror Download [FCC.gov]
Document ID	3789827
Application ID	V1cCoLZRkhjEeWtCmXMxfQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	73.92kB (923947 bits)
Date Submitted	2018-03-21 00:00:00
Date Available	2018-09-15 00:00:00
Creation Date	2017-10-30 09:23:23
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2017-10-30 09:23:26
Document Title	InSync-Wall-Reader_10-17.indd
Document Creator	Adobe InDesign CC 2017 (Macintosh)

Cover
Installation Guide
RFID Wall Reader
Installed with
InSync RAC
Rev. A — 10/2017
P/N 047 515909
InSync Wall Reader Instructions - (All Models)
*CAUTION* Wear Safety Glasses While Preparing Wall
Introduction
The RFID wall mounted reader provided by dormakaba is compact, lightweight, rugged and water resistant, able to
withstand temperatures from -30°F to 150°F (-35°C to 66°C). It is made from durable materials and comes with at
least 15 feet (4.6 m) of cable. The reader is capable of functioning up to distances of 500 feet (152.4 m) when
powered from the RAC controller board.
The reader has a blue LED that indicates that the unit is powered. The reader also provides visual feedback when
access is granted
Surface Mount
Gang Box Mount
Flush Mount
Regulatory Compliance:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interf erence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications of this product, not approved by manufacturer will void the user’s authority to operate
the equipment.
“This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.”
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
FCC-Q8SRINM
IC-4652A-RINM
InSync Wall Reader
Insync Wall Reader Instructions - (All Models)
JP1
InSync Wall Reader Instructions - (Surface Mount)
JP3
JP1-2 Black
JP3-1 Green
JP1-1 Red
JP3-2 White
Mounting Screw
Holes
Figure A. InSync Wall Reader
Figure B. Insync RAC Controller Board
Instructions
1.	Use drilling template provided to prepare surface for installation
2.	Route the wire to the Insync RAC enclosure and connect to the controller board as per the column “RAC Reader
Connection” in table 1, or as per Figure B
3.	Route the other end of the wire through the hole in the mounting plate to the back of the reader and connect as
per column “Reader Connection” in table 1 or as per Figure A
RAC to Wall Reader Connection
Signal
Reader Connection
Terminal Block
Reader Connection
JP1-2
J1, Pin 2
GND
RAC
Wire Color
Comments
Black
GND
+12V
JP1-1
J1, Pin3
Red
+12V
RS485+
JP3-2
J2, Pin 1 + J3, Pin 1*
White
See Note
RS485-
JP3-1
J2, Pin 2 + J3, Pin 2*
Green
See Note
Instructions
1.	Pull cable(s) for RAC through hole in the back plate and, if applicable, through the gasket then screw the mounting
plate of the reader to the wall using the screws provided. Use the 1 1/4" wood screws and inserts for drywall, or use
the 1/2" steel screws for mounting on a metal frame
2. Connect cables for Insync RAC as per page 4 of this document
3.	Hook the top of the reader enclosure (item #2) onto the top of the mounting plate (item #3) and secure together
with the included screw (item #1), tightened at the bottom of the reader
Note: Jumper cables as shown in Figure B must be connected for the reader to operate correctly
Table 1: Insync RAC and Wall Reader Connections
IMPORTANT: The jumper cables supplied with the reader must be connected as shown in Figure B and Table 1 for the
contactless reader to operate properly.
InSync Wall Reader
InSync Wall Reader
InSync Wall Reader Instructions - (Gang Box Mount)
InSync Wall Reader Instructions - (Flush Mount)
FIGURE 1
Instructions
Detail A
1. Remove screws (item #1) to remove reader assembly (item #2) from bracket
2. Install the drywall bracket on the wall
3. Connect cables for Insync RAC as per page 4 of this document
4. Install reader (item #2) then faceplate (item #3) using screws (item #1)
FIGURE 3
Instructions
1. Remove screws (item #1) to gain access to reader assembly (item #4)
2. Carefully remove reader assembly (item #4) (see warning above) remove protective film from reader face
3. Install the gang box with proper screws, not provided
4. Connect cables for Insync RAC as per page 4 of this document
5. Reader assembly orientation to be as shown on page 3 in Figure A.
6.	Re-assemble items #1 through #5 in order as shown in detail A, then assemble to gang box (item #6) and
tighten screws.
InSync Wall Reader
InSync Wall Reader
Customer Services & Support
800 849 8324
General Information:
dormakaba.us

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Language                        : en-US
XMP Toolkit                     : Adobe XMP Core 5.6-c138 79.159824, 2016/09/14-01:09:01
Instance ID                     : uuid:682ead4f-61ee-074d-9e73-441e512a184b
Original Document ID            : adobe:docid:indd:cac64b0d-03ba-11dd-bc21-86ed3a77e383
Document ID                     : xmp.id:29f72d3b-f985-4c02-9efb-3721eec1a3cd
Rendition Class                 : proof:pdf
Version ID                      : 1
Derived From Instance ID        : xmp.iid:eceb032d-9dca-4134-80e2-38b5c0a87c69
Derived From Document ID        : xmp.did:51b5409c-88f2-43ff-a8bd-54c76899aca6
Derived From Original Document ID: adobe:docid:indd:cac64b0d-03ba-11dd-bc21-86ed3a77e383
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2017 (Macintosh)
History Changed                 : /
History When                    : 2017:10:30 09:23:23-04:00
Create Date                     : 2017:10:30 09:23:23-04:00
Modify Date                     : 2017:10:30 09:23:26-04:00
Metadata Date                   : 2017:10:30 09:23:26-04:00
Creator Tool                    : Adobe InDesign CC 2017 (Macintosh)
Format                          : application/pdf
Title                           : InSync-Wall-Reader_10-17.indd
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
GTS PDFX Version                : PDF/X-1:2001
GTS PDFX Conformance            : PDF/X-1a:2001
Slug Family                     : Morebi Rounded
Slug Version                    : 1.000
Slug Outline File Size          : 0
Slug Kerning Checksum           : 0
Slug Foundry                    : --
Slug Font Kind                  : OpenType - PS
Slug Checksum                   : 1709607009
Slug Post Script Name           : MorebiRounded-Black
Slug Font Sense 12 Checksum     : 1709607009
Page Count                      : 5
Creator                         : Adobe InDesign CC 2017 (Macintosh)

EXIF Metadata provided by EXIF.tools