Keeson Technology MC121 CONTROL BOX User Manual MC121

Download:
Mirror Download [FCC.gov]
Document ID	4080255
Application ID	wqwy6eauVJ3wgIMn3tpfVw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	30.23kB (377813 bits)
Date Submitted	2018-11-21 00:00:00
Date Available	2018-11-21 00:00:00
Creation Date	2018-10-20 17:57:34
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2018-11-21 10:46:34
Document Title	Microsoft Word - MC121_User Manual
Document Creator	PScript5.dll Version 5.2.2
Document Author:	baclsh51

Issue department：Bedding Division
ProductFunction
instruction
Date：
Author：
No：
Version：
1.1
Page 1 of 3
MC121
MC121Function instruction
1. Electrical configuration diagram：
FCC ID:PCU-RF258GA
IC:21319-RF258GA
2. Function Picture
1.
2018-03-26
Kyle
Process of test
1.1. HEAD port
Connect to head actuator,control by remote single:
Click head up button on the remote, head actuator moves out, stop when released；
Click headdown button，head actuator moves in, stop when released；
This function takes effect only by pressing the corresponding button on the remote.
Issue department：Bedding Division
ProductFunction
instruction
Date：
Author：
2018-03-26
Kyle
No：
Version：
1.1
Page 2 of 3
MC121
1.2. FOOTport
Connect to foot actuator,control by remote single:
Click foot up button，foot actuator moves out，stop when released；
Click foot down button，foot actuator moves in，stop when released；
This function takes effect only by pressing the corresponding button on the remote.
1.3. Massage
Connect to headmassage,control by remote:
Click head massage + button,head massage strengthens by one level;
Click head massage ‐ button,head massage weakenby one level;
This function takes effect only by pressing the corresponding button on the remote.
1.4. MULTIFUNCTION port
Connect with the same Other accessories;
1.5. Power LED& PAIRING LED
Power supply for control box, PAIRINGLED of control box flashes for 4 times,and then turns off, POWER LED turns
on。
1.6. Power
Connect to the 29V DC;
1.7. Pair Function
Power up control box，pairing LED will be flash，the control box enters into mode of code paring；
Press and hold the paring LED of Remote, the backlight of paring LED flashes, the backlight of remote flashes, the
remote enters into mode of code paring;
The backlight of paring LED of remote stops flashing, and the paring led of control box stop flash, it indicates that
the code paring is successful;
If fails, repeat all the processes above;
1.8. FLAT function
Press and release the FLAT buttonon remote，the head and foot actuators moves to lower position(when the
actuator is free, can turn off the vibration motor and turn off the indicator light when press once )，stop when
press any buton；
This function takes effect only by pressing the corresponding button on the remote.
1.9. ZERO G position function
Press and release ZERO G button on remote，the head and foot actuator moves to preset memory position，stop
when press any button；
Issue department：Bedding Division
ProductFunction
instruction
Date：
Author：
2018-03-26
Kyle
No：
Version：
1.1
Page 3 of 3
MC121
This function takes effect only by pressing the corresponding button on the remote.
FCC：
Any Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
ISED RSS Warning:
This device complies with Innovation,Science and Economic Development Canada
licenceexempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this devicemay not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio
exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm
between the radiator& your body.This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. Le rayonnement de la classe b
repecte ISED fixaient un environnement non contrôlés.Installation et mise en œuvre de
ce matériel devrait avec échangeur distance minimale entre 20 cm ton corps.Lanceurs
ou ne peuvent pas coexister cette antenne ou capteurs avec d’autres.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : baclsh51
Create Date                     : 2018:10:20 17:57:34+08:00
Modify Date                     : 2018:11:21 10:46:34-08:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Creator                         : baclsh51
Title                           : Microsoft Word - MC121_User Manual
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2018:11:21 10:46:34-08:00
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:25604734-163c-45ee-b981-921e76e7fba5
Instance ID                     : uuid:0120dab7-184f-4ff1-9a33-f9eaeb12749d
Page Count                      : 3

EXIF Metadata provided by EXIF.tools