Koden Electronics RB718A Marine Radar RA54 User Manual OME RA5354 1of4
Koden Electronics Co., Ltd Marine Radar RA54 OME RA5354 1of4
Contents
- 1. Manual1of4
- 2. Manual2of4
- 3. Manual3of4
- 4. Manual4of4
Manual1of4
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 166979 |
| Application ID | J39wGaKd4nGEpEnO+OAq6Q== |
| Document Description | Manual1of4 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 93.38kB (1167204 bits) |
| Date Submitted | 2001-08-31 00:00:00 |
| Date Available | 2001-10-03 00:00:00 |
| Creation Date | 2001-08-29 15:33:30 |
| Producing Software | Acrobat PDFWriter 4.0 Windows NT |
| Document Lastmod | 0000-00-00 00:00:00 |
| Document Title | OME_RA5354_1of4.PDF |
| Document Creator | OME_RA5354_1of4.rtf - Microsoft Word |
| Document Author: | 109983 |
Safety Symbols To prevent the risk of personal injury or damage to the equipment, the following safety symbols are used to indicate safety-related information. Insure that you clearly understand the meanings of the symbols BEFORE using the equipment. Symbols Used in Manual DANGER This indicates a very dangerous procedure that could result in serious injury or death if not performed properly. WARNING This indicates a hazardous procedure that could result in serious injury or death if not performed properly. CAUTION This indicates a hazardous procedure or danger that could result in light-to-severe injury, or that might damage the equipment, if proper precautions are not taken. Safety Symbols Used on Equipment The following safety symbols are used inside or on the equipment near operation locations to provide information about safety items and operation precautions. Insure that you clearly understand the meanings of the symbols and take the necessary precautions BEFORE using the equipment. This indicates high voltages with a risk of serious electric shock if the part is touched. NEVER touch the part with bare hands, etc. The symbol prohibits the operation shown inside the symbol. (The example in the left prohibits disassembly.) The symbol indicates that the operation inside the symbol is potentially hazardous. (The example on the left indicates that the plug should be held when disconnecting it from the AC outlet.) This indicates the ground (earth) terminal. If the equipment cannot be grounded via the power cord, connect this terminal to ground. There is a risk of serious electric shock if the equipment is not grounded. RA53/RA54 Marine Radar Instruction Manual 1st Jun. 2001 (1st Edition) Document: E-A53/54-1 For Safety WARNING and CAUTION for Scanner Unit and Antenna ; 1. Do not approach the antenna while it is transmitting. In addition, at inspection never look into the wave guide during transmission. Distance at which RF power density level to become 100 W/m2: Distance at which RF power density level to become 10 W/m2: 2m 6m 2. There is a risk of receiving electric shock if these parts are touched by accident. Only qualified personnel should remove covers on these parts. 1. 2. WARNING for Display Unit ; There is a risk of receiving electric shock if these parts are touched by accident. Only qualified personnel should remove covers on these parts. Installation Only qualified personnel should install the radar system in order to make sure proper radar performance and operation. To Customers * To always use this equipment at its best condition, we recommend observing the operation and maintenance procedures in this manual from time to time. Further, try to operate the radar in good visibility condition to make comparison between visual impression and the radar picture presentation of the situation you are in. By doing this, you will be able to gain practical knowledge in interpreting the radar picture as well as the false echoes and blind sectors caused by the masts or funnel of the ship. Note that this equipment should only be used as a navigational aid and ship’s crew must make final decision on ship’s maneuvering. * In case of functional failure, immediately turn off the radar and switch off the ship’s main power supply at the distribution switchboard. Inform your local service agent of the faulty situation to detail, where possible. * This instrument uses crystal oscillators and a LCD backlight lamp, which are vulnerable to mechanical shock. Take utmost care when handling these items * The mercury (Hg) is used in the LCD backlight lamp. When you attempt to discard your radar, observe the local code of practice for deposit. Contents For safety CHAPTER 1 OVERVIEW......................................................................... 8 1.1 Introduction............................................................................................................8 1.2 Organization of This Manual ................................................................................8 CHAPTER 2 USING RADAR FOR THE FIRST TIME .......................... 9 2.1 What is a radar ?....................................................................................................9 2.2 Characteristics of Radar Wave .............................................................................10 2.3 Terms Specific to Radars.......................................................................................13 CHAPTER 3 INSTALLATION................................................................. 16 3.1 Checking Contents of Your Package.....................................................................16 3.2 Checking Power Supply Voltage ...........................................................................17 3.2.1 Power Supply Requirement .............................................................................17 3.2.2 Fuse Replacement.............................................................................................17 3.3 Determining Place of Installation.........................................................................18 3.3.1 Scanner unit......................................................................................................18 3.3.2 Display unit.......................................................................................................18 3.3.3 Shifting away from obstacles ...........................................................................19 3.4 Installing Scanner Unit.........................................................................................20 3.5 Installing Antenna Unit ........................................................................................21 3.6 Installing Display Unit..........................................................................................22 3.7 Connecting Cables .................................................................................................22 3.7.1 Interconnecting cable........................................................................................22 3.7.2 Grounding wire .................................................................................................24 3.7.3 Power supply cable ...........................................................................................25 3.8 Adjustment.............................................................................................................25 3.9 Connecting External Equipment to Display Unit ...............................................26 3.10 Countermeasure for Electromagnetic Interference...........................................26 3.11 When Discarding Your Radar .............................................................................27 CHAPTER 4 FUNCTIONS AND NAMES............................................... 28 4.1 Key layout ..............................................................................................................28 4.2 Rear panel ..............................................................................................................29 4.3 Radar screen (Single screen).................................................................................29 4.4 Radar screen (Dual screen) ...................................................................................30 4.5 Radar screen (All PPI screen) ...............................................................................30 4.6 Radar screen (All PPI/PPI screen) ........................................................................31 4.7 Navigation screen ..................................................................................................31 CHAPTER 5 OPERATION....................................................................... 32 Basic operation of Radar .............................................................................................32 5.1 Turning ON and OFF the radar ...........................................................................32 5.2 Adjusting brilliance of screen and key-backlight.................................................32 5.3 Basic Operations ....................................................................................................33 5.3.1 Powering On and Off ........................................................................................33 5.3.2 Transmitting .....................................................................................................33 5.3.3 Adjusting the brilliance of the screen and key-backlight...............................34 5.3.4 Changing the range scale (RANGE UP, RANGE DOWN).............................34 5.3.5 Automatic adjustment (AUTO)........................................................................34 5.3.6 Sensitivity adjustment (GAIN) ........................................................................ 35 5.3.7 Removing the sea clutter (STC) ....................................................................... 35 5.3.8 Removing the rain and snow clutter (FTC)..................................................... 36 5.3.9 Man Over Board (MOB).................................................................................... 36 5.3.10 Acquisition of a target (ACQ)............................................................................... 36 5.3.11 Select target number (TGT NUM) ...................................................................... . 36 5.4 Functions of Soft Keys........................................................................................... 37 5.4.1 Bearing measurement (EBL1) ......................................................................... 37 5.4.2 Bearing measurement (EBL2) ......................................................................... 37 5.4.3 Distance measurement (VRM1)....................................................................... 37 5.4.4 Distance measurement (VRM2)....................................................................... 38 5.4.5 Measuring the angle between two points (FL EBL2) ..................................... 38 5.4.6 Measuring the distance between two points (FL VRM2) ............................... 38 5.4.7 Changing the group of Soft Keys(NEXT) ........................................................ 38 5.4.8 Erasing the heading marker temporarily (HDG OFF)................................... 39 5.4.9 Using the parallel cursor (///CSR).................................................................... 39 5.4.10 Establishment of the indication of the RANGE RINGS (RINGS) ............... 39 5.4.11 ON/OFF of variable range function (VAR RNG) .......................................... 39 5.4.12 Changing the display modes (MODE) ........................................................... 39 5.4.13 Guard Zone (GZ) ............................................................................................. 40 5.4.14 Off Center (OFF-C) ......................................................................................... 40 5.4.15 Setting up the SLEEP function(SLEEP)....................................................... 41 5.4.16 Tuning adjustment (TUNE) ........................................................................... 41 5.4.17 Echo expansion (ST) ....................................................................................... 41 5.4.18 Displaying the target track (TRACK)............................................................ 41 5.4.19 Enlarging the selected areas (ZOOM) ........................................................... 42 5.4.20 Increasing the sensitivity (S/L) ...................................................................... 42 5.4.21 Switching the screen (SEL WIN) ................................................................... 42 5.4.22 Changing the screen color (PICTURE).......................................................... 43 5.4.23 Change to PPI screen (PPI)............................................................................ 43 5.4.24 Change to SEMI3D/PPI screen (SEMI3D) .................................................... 43 5.4.25 Change to PPI/PPI screen (PPI/PPI) ............................................................. 43 5.4.26 Change to PPI/NAV screen (PPI/NAV) ......................................................... 44 5.4.27 Change to ALL PPI screen (ALL PPI) ........................................................... 44 5.4.28 Change to ALL PPI/PPI screen (ALL PPI2).................................................. 44 5.4.29 Canceling target tracking (DEL)................................................................... 44 5.4.30 Canceling all target tracking (ALL DEL) ..................................................... 44 5.4.31 Data display (DATA)...................................................................................... 44 5.5 MENU Operation .................................................................................................. 46 - List of MENU ......................................................................................................... 46 5.5.1 Mark Menu........................................................................................................ 47 5.5.1.1 Bearing measurement (EBL1) ..................................................................... 47 5.5.1.2 Determining the distance (VRM1)............................................................... 48 5.5.1.3 Bearing measurement (EBL2) ..................................................................... 48 5.5.1.4 Determining the distance (VRM2)............................................................... 48 5.5.1.5 Measuring the distance or angle between two points ( FL EBL2, FL VRM2 ) ...................................... 48 5.5.1.6 Measuring the angle between two points (FL EBL2)................................. 49 5.5.1.7 Erasing the heading marker temporarily (HDG OFF) .............................. 50 5.5.1.8 Using the parallel cursors (///CSR) .............................................................. 50 5.5.1.9 Displaying the RANGE RINGS (RINGS) ................................................... 51 5.5.1.10 Variable range function ( VAR RNG ) ....................................................... 51 5.5.1.11 To output the Cursor (TARGET) position data to external equipment .. 52 5.5.1.12 Setting the Distance and Bearing marker to follow the cross cursor (+MK LINE) ........................................ 52 5.5.2 Nav (Navigation) Menu..................................................................................... 52 5.5.2.1 Changing the display mode (MODE) ......................................................... 53 5.5.2.2 Setting the Guard Zone (GZ) ....................................................................... 53 5.5.2.3 Shifting the display to a specific direction (OFF-C) ................................... 54 5.5.2.4 Setting up the SLEEP function(SLEEP)..................................................... 55 5.5.3 Echo Menu .......................................................................................................... 56 5.5.3.1 Sensitivity adjustment (GAIN).................................................................... 56 5.5.3.2 Removing the sea clutter (STC)................................................................... 57 5.5.3.3 Removing the rain and snow clutter (FTC) ................................................ 57 5.5.3.4 Adjusting the receiver tuning (TUNE)........................................................ 57 5.5.3.5 Echo expansion (ST) ..................................................................................... 58 5.5.3.6 Displaying the target track (TRACK)..........................................................58 5.5.3.7 Enlarging the selected areas (ZOOM) .........................................................59 5.5.3.8 Increasing the sensitivity (S/L) ....................................................................59 5.5.4 SETUP Menu ....................................................................................................60 5.5.4.1 Selecting and setting up the screen mode (WINDOW) ..............................60 - Available funtions on each screen mode ...............................................................61 - Screen modes and Operations................................................................................62 (a) PPI Screen..................................................................................................62 (b) PPI/SEMI3D Screen ..................................................................................62 (c) PPI/PPI Screen ...........................................................................................62 - Operation.......................................................................................................63 (d) PPI/NAV Screen.........................................................................................64 (e) ALL PPI Screen..........................................................................................64 (f) ALL PPI/PPI Screen ...................................................................................64 (g) MOB Screen ...............................................................................................64 5.5.4.2 Switching screens on PPI/PPI screen (SEL WIN) ......................................65 5.5.4.3 Changing the screen color (PICTURE)........................................................65 5.5.4.4 Fault Diagnosis by Self Check (SYSTEM CHECK)....................................66 5.5.4.5 Changing the content of the setting (CUSTOM) ........................................68 5.5.4.5.1 Changing the settings of the soft keys (KEY ASSIGN)..........................69 5.5.4.5.2 Changing the content of settings 1(PRESET1).......................................71 5.5.4.5.3 Changing the content of settings 2 (PRESET2)......................................73 5.5.4.5.4 Changing the content of priority for NMEA input(NMEA PRESET) ...75 5.5.4.5.5 Changing the content of settings (ADJUSTMENT) ............................... 75 (1) Adjusting the distance (TIMING ADJ).................................................. 75 (2) Adjusting the angle (HEAD ADJ) .......................................................... 76 (3) Adjusting the receiver tuning (TUNING CAL) ..................................... 76 (4) Adjusting the antenna height (ANTENNA) .......................................... 77 (5) Setting the receiver GAIN (GAIN)......................................................... 77 (6) Setting the STC level (STC) ................................................................... 78 5.5.4.5.6 ATA preset (ATA PRESET)...................................................................... 78 5.6 ATA Operation ....................................................................................................... 79 5.6.1 ATA Board Specifications.................................................................................. 79 5.6.2 Operating Instructions ...................................................................................... 79 5.6.2.1 Outline........................................................................................................ 79 5.6.2.2 Setting ........................................................................................................ 79 5.6.2.3 Operation.................................................................................................... 80 (1) Acquisition of a target..................................................................................... 80 (2) Tracking the target ......................................................................................... 80 (3) Canceling target tracking............................................................................... 80 (4) Data display .................................................................................................... 80 (5) ATA indications..................................................................................................... 81 5.6.2.4 Interface ..................................................................................................... 81 (1) Data output ..................................................................................................... 81 (2) Log signal input .............................................................................................. 81 CHAPTER 6 MAINTENANCE AND INSPECTION .............................. 82 CHAPTER 7 TROUBLESHOOTING....................................................... 84 7.1 Fault Diagnosis by Self-check ...............................................................................84 7.2 Inspecting Each Part .............................................................................................85 CHAPTER 8 PRODUCT SPECIFICATIONS.......................................... 86 8.1 General ................................................................................................................... 86 8.2 Scanner Unit .......................................................................................................... 87 8.3 Display Unit ........................................................................................................... 87 8.4 ATA Unit ................................................................................................................ 88 8.5 External Interface.................................................................................................. 89 8.6 Standard set ........................................................................................................... 89 8.7 Options.................................................................................................................... 89 8.8 External dimensions and weight ...........................................................................89 8.9 External connection and function..........................................................................90 APPENDIX 1. 2. 3. 4. 5. 6. 7. RA53 GENERAL SYSTEM DIAGRAM RA54 GENERAL SYSTEM DIAGRAM INTERCONNECTION DIAGRAM OUTLINE DRAWING DISPLAY UNIT RA53/54 OUTLINE DRAWING SCANNER UNIT FLUSH MOUNT PROCEDURE INDEX 24W159631 E43BG11000 E38BG62000 E43BG11020 CHAPTER 1 OVERVIEW 1.1 Introduction The RA53/54 represents a compact, high-performance color marine radar that delivers a peak power output of 6 kW(RA53) or 12 kW(RA54) from the antenna and uses a 15-inch color liquid crystal display. In addition to a microcomputer, it incorporates a video signal processing LSI and a newly developed LSI chip exclusively designed for radars, thus providing versatile functionality and high performance. Features 1. A thin display unit incorporating a liquid crystal display. 2. Easy operation using only a few keys and menu screens. 3. A position of key and its function can be set in position ( Selectable soft function key). 4. Easy operation by the rotary knob. Gain, STC, FTC, EBLs, VRMs etc. can be controlled by the rotary knob. 5. A short and a long range echo can be seen at the same time ( Dual range radar). 6. Semi-3D screen display for easy identification of targets in noise. 7. Capable of continuous distance range changes (Continual variable range). 8. Waterproof construction of display allows installation at any desired location. 1.2 Organization of This Manual This manual provides a wide range of information necessary to operate the RA53/54 radar ranging from the basic knowledge on radars to the methods of operating, installing, and maintaining the radar. The manual also provides rather detailed technical information on how to adjust video display to obtain clear images. You are requested to read this manual thoroughly from beginning to end in order to understand the various functions of the radar so you can take full advantage of its advanced functions. If you are using a radar for the first time, refer to the basic data on radars in CHAPTER 2. This manual consists of the following chapters: USING RADAR FOR THE FIRST TIME INSTALLATION FUNCTIONS AND NAMES OPERATION INSPECTION AND MAINTENANCE TROUBLESHOOTING PRODUCT SPECIFICATIONS ...................... ...................... ...................... ...................... ...................... ...................... ...................... CHAPTER 2 CHAPTER 3 CHAPTER 4 CHAPTER 5 CHAPTER 6 CHAPTER 7 CHAPTER 8 If you are an experienced user of radars, skip CHAPTER 2 and begin from CHAPTER 3. CHAPTER 2. USING RADAR FOR THE FIRST TIME This chapter describes basic information on radars and explains technical terms used in radar operation for those who are using a radar for the first time. 2.1 What is a radar ? A marine radar is one of the navigation equipment installed on a ship. It emits a radio wave in very high frequency called a microwave from its antenna and receives the reflected radio wave from objects on the sea (e.g., other ships, buoys, and lands). The received radio wave is converted into an electric signal which is displayed on a display screen to indicate the presence of such objects. Although it is very difficult to find other ships or the destination coast with human eyes at night or in thick fog, a radar can detect objects on the sea helping you avoid danger when sailing. The antenna turns 360 degrees as it radiates waves, allowing you to grasp ambient conditions around your ship at a glance. The radio wave radiated from the antenna is called a pulse wave and the radar performs transmission and reception alternately. Several hundred to several thousand pulse waves generally are transmitted while the antenna rotates one turn. Buoy Other ship Radar wave Your ship Radar display Antenna (Rotating) Fig.2-1 What is a radar? Antenna There are many types of antennas generally used for a radar. For example, these include a parabolic antenna and a slotted-array antenna. The performance of the antenna determines that of the radar. The dominant factors are the antenna's beam width and side lobe level. The narrower the beam width, the higher the resolution of the angle direction. The lower the side lobe level, the fewer the effect of a false echo. Side lobe A beam in one direction in which the strongest radio wave is radiated from the antenna is called the main lobe and beams in other directions are called "side lobes". The side lobe level refers to the difference in level between the largest side lobe and the main lobe. Beam width A beam width is defined as the width of the main lobe at an angle where the radiated power is halved as measured from the position from which the strongest radio wave is radiated. Side lobe level Beam width Main beam Side lobe Antenna Fig.2-2 Antenna pattern 2.2 Characteristics of Radar Wave Radio waves from the radar propagate while bending slightly along the terrestrial surface. This characteristic varies dependent on the density of the atmospheric air. The sight distance D of a radar generally is said to be approximately 6% longer than the optical sight distance and is calculated using the equation below : D (NM) = 2.22 ( h1 + h2 ) where, h1= antenna height in meters h2= target height in meters Line of sight Radar Radio Wave h1 h2 Earth Fig.2-3 Radar wave Targets difficult to display on screen The intensity of the reflected wave from a target depends on the distance, height, and size of the target, as well as its material and shape. Targets constructed with FRP, wood, or other low-reflectance materials or those that have a small incident angle are difficult to display on a screen. Therefore, FRP and wooden ships, sandy beaches, and sandy or muddy shallows all are difficult to catch and require attention when monitoring on the screen. Especially, coast lines on the radar image appear to be present further from the ship than they are actually located. Therefore, it is important not to misinterpret the available data. Invisible Apparent coastline Visible HU Actual(invisible) coastline Fig.2-4 Targets difficult to display on screen Shadow zones of radar Radar waves are characteristic in that they propagate straight ahead. Therefore, if the ship's smokestack or mast is located near the antenna or there is a tall ship or mountain at the side of the ship, such an object generates a shadow behind it. In this case, some objects produce a complete shadow and some produce a partial shadow. In an extreme case, the shadow of an object may extend to a position far away and cannot be displayed on the screen at all. Since these shadows can be discovered when installing an antenna, the problem can be avoided by changing the place of antenna installation to minimize the shadow. Targets in shadow zones are difficult to display on the screen. False echoes A false echo of an actually nonexistent object may sometimes appear on the screen when sailing. The following explains the cause of each such phenomena. 10 A. Ghost echoes It sometimes happens that one large object near the ship appears at two different bearings. One is the actual echo and other is a ghost echo generated as the wave is re-reflected from the ship's own smokestack or mast. The former appears at the correct distance and bearing on the screen and the latter appears behind the smokestack or mast. This type of false echo is also generated by re-reflection of waves from bridges and quay walls other than the ship itself. Target Direct reflection path Real echo HU Secondary reflection path Ghost echo Mast etc. Direction of ghost echo Fig.2-5 False echoes of radar (Ghost echoes) B. Multiple echoes If there is a large vertical reflecting plane near the ship as in the case when your ship passes alongside a large ship, the wave is repeatedly reflected back and forth between your ship and the other object. For this reason, two to four images appear on the screen at equal intervals in the same bearing. A false echo that is generated by such multiple reflections is called multiple echoes. In this case, an image appearing at the nearest position is the real echo. Multiple echoes disappear as the ship moves away from the reflecting object or its bearing changes. Therefore, it is not difficult to determine the correct image. HU Real echo Multiple echoes Fig.2-6 False echoes of radar (Multiple echoes) C. False echoes caused by side lobe The radiant beam emitted from an antenna contains side lobes in directions other than that of the main beam. Since the side lobe level is low, it in no way affects distant targets. However, if there is a strong reflecting target near the ship, it sometimes appears as a circular-arc false echo on the screen. CAUTION When located near large targets such as land, the ship's mast, etc. sometimes appears as a false echo of circular-arc shape. 11 Main beam False sidelobe echoes HU Real echo Side lobes Antenna Fig.2-7 False echoes of radar (Caused by side lobe) D. Distant false echoes caused by duct phenomenon Depending on meteorological conditions, duct phenomenon sometimes occurs in temperature inverting layers of air. In such a case, the wave propagates erratically reaching a location surprisingly far away from the ship. In this case, a target present at a distant location more than the radar's maximum distance range appears on the screen presenting a false echo that can be misunderstood to be present nearer than the actual position. This phenomenon is attributed to the fact that since echo from the distant target arrives late, it gets out of the pulse repetition frequency and is displayed on the screen as an echo in the next frequency. If the target distance changes as you switch over the distance range, you can determine that it is a false echo. Radar inrterference Radar interference If a radar operating in the same frequency exists near your ship, interference noise may appear on the screen that is caused by transmitted waves from that radar. This interference appears in various ways. In most cases, however, it appears as spiral or radial patterns. The RA53/54 radar has a function to eliminate interference. Use of this function helps you minimize interference. HU Fig.2-8 Radar interference 12 2.3 Terms Specific to Radar HM(Heading Marker) HM (Heading Marker) This is a line-shaped marker used to indicate the advancing direction of your ship. 0.75 0.25 HU North Mark This marker indicates the north direction. It is a short line approximately 1/6 of the screen size. North Mark Fig.2-9 Heading Marker and North Mark Display modes This refers to a radar's display modes. There are four display modes depending on the direction in which the top of the screen faces with respect to the ship. Ship's Heading HM Ship's locus (not displayed on screen) Scheduled course Scheduled course North North 0.75 0.75 0.75 0.75 0.25 HU 0.25 NU 0.25 CU 0.25 TM North mark North EBL HU NU CU TM Fig.2-10 Display modes Head Up (HU) In this mode, the ship's heading always indicates the upward direction of the screen. This mode lets you know the relative positions of your ship and other ships or land. North Up (NU) In this mode, the north direction always indicates the upward direction of the screen, allowing you to compare your ship’s position with a marine chart as you navigate. Course Up (CU) The ship's heading in a course-up mode always indicates the upward direction of the screen as the bearing toward the destination. In this mode, the ship can be maneuvered to sail the shortest distance to the destination by steering it in such a way that its heading marker always directs to the upward direction of the screen. If the ship drifts due to tidal current, care must be taken because the fixed targets move to other positions. True Motion (TM) In this mode, the ship is displayed as if it is moving on a marine chart while the fixed targets such as islands and seashores are fixed in position. When the ship reaches a certain position on the screen (approx. 2/3 of screen size), the ship is placed back to the opposite side on the screen. (The top of the screen faces north.) 13 Note: Navigation equipment such as a gyrocompass or magnet compass must be connected to your radar system before it can be operated in NU, CU, and TM modes. (Refer to Section 3.9 for details on how to connect your radar to navigation equipment.) VRM (Variable Range Marker) This is a circular-shaped marker whose size can be changed as desired. You can use this marker when you want to examine the distance of an echo from your ship. When measuring the distance of an echo from your ship, be sure to measure at a point close to the center of the echo image on the screen. 0.75 0.25 HU Echo EBL VRM VRM Fig.2-11 VRM EBL (Electronic Bearing Line) This is a marker shaped like a straight line segment that can be changed to any direction centering around the ship’s position. Use this marker to examine the advancing direction of your ship and its relative angle with an echo. When measuring the angle of an echo, position the marker at the center of the echo. 0.75 0.25 HU EBL Echo EBL VRM Fig.2-12 EBL 14 STC (Sensitivity Time Control) Since echo signals received by the radar are strong when they are coming from a short distance, it is difficult to compare signal strength between each reflected signal. To overcome this difficulty, signal strength is adjusted in such a way that the received signal levels coming from a short distance are lowered and those from a long distance are raised. This function should prove useful when there are large reflected waves from sea surfaces during rough weather. STC OFF STC ON 0.75 0.75 0.25 HU 0.25 HU Echo is suppressed around center Fig.2-13 STC FTC (Fast Time Constant) When it rains or snows, fine noise may appear over the entire screen, making it difficult to identify echoes. In such a case, echo images on the screen can be made easily distinguishable by adjusting FTC. FTC OFF FTC ON 0.75 0.75 0.25 HU 0.25 HU Small noises are reduced. Fig.2-14 FTC 15 CHAPTER 3. INSTALLATION This chapter describes procedures for installing the RA53/54 radar in your ship and precautions to be observed during installation. Follow the procedure below to install the radar. Checking contents of your package Checking power supply voltage Determining place of installation Installing scanner unit Installing display unit Connecting cables Adjustment Connecting external equipment When discarding Your radar 3.1 Checking Contents of Your Package First, unpack your package and see if all of the following items are included. Item Display unit Scanner unit Display cover Fuse Interconnecting cable Power supply cable M12 hexagonal bolt Carbon brush RA53 Q'TY 1 (RF720A) 1 (RB717A) 1 (10 m) 1 (2 m) 4 sets RA54 Q'TY 1 (RF720A) 1 (RB718A) 1 (10 m) 1 (2 m) 4 sets The package contains a 10m interconnecting cable as an accessory. Longer cable is also available as an option as listed in Tab.3-1. 16 Tab.3-1 Optional Interconnecting Cable Cable length 15m 20m 30m RA53/RA54 Product No. 242J159098B 242J159098C 242J159098D In addition to the above components included with your package, the following items are also required. Please prepare them separately. Item Tapping screw or M5 bolt and nut Grounding wire Grounding wire and crimp terminal QTY 6 sets 1 set Remarks To install display unit Earth line for display unit Earth line for scanner unit 3.2 Checking Power Supply Voltage 3.2.1 Power Supply Requirements For the RA53/54 radar to be operated normally, the power supply (battery) detailed in Tab.3-2 is required. Note also that if the battery is discharged, its voltage may fluctuate greatly, causing the radar to malfunction. When to starting up the radar system or starting transmitting, an additional rush current is required on the power supply line. Carefully check the power supply system including wiring by using a circuit tester. Tab.3-2 Power Supply Requirements Supply voltage used DC12V DC24V Maximum current 14A 6A Allowable range of voltage 10.2-41.6V 10.2-41.6V *A.C. power cannot be used 3.2.2 Fuse Replacement For the RA53/54 radar to be operated safely, proper rated fuses must always be used. Tab.3.3 is fuse rating table. All these fuses are provided as spares. Tab.3-3 Supply Voltage vs Fuse Ratings Main Fuse 15A/250V or 125V * (6.3 dia. x 32mm) Motor Fuse T3.15A/250V or 125V (5 dia. x 20mm) 17 3.3 Determining Place of Installation 3.3.1 Scanner unit A radar's target detection capacity varies greatly depending on the position of the scanner. An ideal position is a location high above the ship's keel line where there is no obstacle all around the scanner. In an actual ship, such an ideal location is limited by various factors. To comply with FCC RF exposure requirements, the radar antenna for this scanner must be installed to provide a separation distance of 80 cm or more from all persons. Therefore, consider the following suggestions when you determine the place to install the scanner: (a) Install scanner at a position as high as possible. The higher the installation position, the longer the radio ranging distance. Install the scanner at a position as high as possible after considering the ship's hull structure and radar maintainability. (b) Install scanner away from smoke-stack and mast If the scanner is installed at the same height as the smoke-stack or mast, radar waves may be blocked, creating shadow zones or generating false echoes. Therefore, do not install the scanner at such a position. (c) Install scanner forward away from obstacle. To avoid creating shadow zones or generating false echoes, install the scanner at a position nearer to the ship's bow away from obstacles. When installing the scanner on a mast, position it in front of the mast. (If obstacles cannot be avoided for the ship's structural reasons, refer to "Shifting away from obstacles" described Page 13.) (d) Do not install the scanner near hot or heat-generating items. Do not install the scanner at a position where it may be subjected to smoke or hot air from smokestacks or heat from lamps. (e) Install the scanner away from antennas of other equipment. Install the scanner as much away from the antennas of a direction finder, radio transceiver, etc. as possible. CAUTION To eliminate the interference, install the scanner away from the antenna of radio transceivers. (f) Make the cable length as short as possible. Keep the distance from the scanner to the display unit within the standard cable length of 10 m. If you use longer cable for unavoidable reasons, limit the cable length to a maximum of 100 m for RA53/54. 3.3.2 Display unit The display unit can be installed on desktop, wall surface, or ceiling. Determine the place to install the display unit that is convenient for navigation and radar operation after considering the following suggestions: (a) A place where you can see the ship's bow when you raise your face from the radar screen. (b) A place where there is no direct sun-light to avoid display temperature up. (c) A place where there is good ventilation and minimum vibration. (d) A place where the display unit is further away than the minimum safe distance from a magnet compass as listed in Tab.3-4 below. Tab.3-4 Minimum Safe Distance from Magnetic Compass Scanner unit Display unit Master compass 2.0m 2.0m 18 Steering compass 1.4m 1.4m 3.3.3 Shifting away from obstacles 1. Shifting from keel line By shifting the scanner position from the keel line to the starboard side of the ship, it is possible to move shadow zones to the port side which makes it possible to keep vision clear in the bow direction. The distance to be shifted can be obtained by calculation depending on the distance from the scanner to obstacles using the following equation: Ls=0.4R+D/2 [m] (when R<15m) Ls=0.025R+D/2 [m] (when R>=15m) where Ls = distance to be shifted from keel line D = diameter of obstacle on keel line R = distance from scanner to obstacle Scanner Unit Obstacle Ls Keel line Fig.3-1 Shifting from keel line 2. Obtaining sufficient dip angle Raise the scanner position so that there is a sufficient dip angle θ available between the line of sight from the scanner to the obstacle and the horizontal line. By raising the dip angle above 5°, it is possible to prevent mid- and long-distance shadow zones. The radar cannot detect objects below the line of sight. Horizontal line θ Line of sight Fig.3-2 Obtaining sufficient dip angle 19 3.4 Installing Scanner Unit When you have decided the place of installation, install the scanner unit. If a mount base like the one shown below is available, it may be easier to install the scanner. If such a mount base is not available in your ship, you may install the scanner directly to the roof, etc. In such a case, pay attention to the water drain tube located at the bottom of the scanner unit during installation. Note : When the radar mast or mounting bracket has a curvature of more than 2mm, repair it or use spacers. Do not use an edge that might trap water. Fig.3-3 Mount base Referring to Fig.3-4, open holes in diameter of 12 mm (0.47 in.) at five locations in the mount base and use these holes to fix the scanner unit to the mount base with hexagonal bolts. (Use the template included with this manual.) The bolts included with your radar equipment will suffice for mount base thickness of 9 to 14 mm (0.35 to 0.55 in.). If the mount base is thicker or thinner than this, prepare bolts listed in Tab.3-6. Forward 199 (7.83 in.) Rotation Radius R550 (3 ft antenna) R700 (4 ft antenna) R1000 (6 ft antenna) 185 (7.28 in.) 14 dia.× 4 Cable inlet (0.55 in.) 100 dia.(3.97 in.) RA53/54 Scanner Fig.3-4 Hole positions for mounting scanner 20 Unit:mm Double nuts Spring washer Washer Scanner base Mount base M12 Hexagonal bolt Fix four screws Fig.3-5 Fixing Scanner Unit Tab.3-5 Bolts for Mounting Scanner Unit Thickness of mount base 1-4mm(0.04-0.16 in.) 4-9mm(0.16-0.35 in.) 9-14mm(0.35-0.55 in.) 14-19mm(0.55-0.75 in.) Bolts necessary to fix scanner M12 x 45 (1.5mm pitch) M12 x 50 (1.5mm pitch) M12 x 55 (1.5mm pitch) M12 x 60 (1.5mm pitch) Material Stainless Stainless Stainless Stainless Remarks Included with radar 3.5 Installing Antenna Unit Remove the protective cap covering the rotary coupler on the top of the scanner. Match the antenna radiation direction to direction of the arrow markings on the rotation base and fix the antenna in position using the four M8 accessory bolts. Antenna radiation surface Arrow 21 3.6 Installing Display Unit After you have finished installing the scanner unit, install the display unit in the same way. Choose the proper bolt length according to the thickness of the surface on which you are going to install the display unit. Hole diameter is different using bolts from using tapping screw. When using tapping screw, open holes in adequate holes. When using bolts and nuts, open holes in diameter of 6 mm (0.24 in.). When you have opened holes, install the pedestal part first and then the display unit. Fitting hole 360 (14.17 in.) Hole diameter 6mm 47 (1.85 in.) Adequate 84 (3.31 in.) : Bolts and Nuts : Tapping screws 37 (1.46 in.) Recommended screw 60 240 60 (2.36 in.) (9.45 in.) (2.36 in.) M5 or equivalent Unit : mm Forward Fig.3-6 Hole positions for display unit Note : When you install the display by flush mount, refer to appendix "OUTLINE DRAWING". Slide off four triangle corner covers, and fix the display unit to the panel with screws. After fixing the display unit, put on corner covers to the corner of the display unit. See APPENDIX. WARNING Avoid operating display in direct sunlight. The temperature inside becomes high and display may be broken. 3.7 Connecting Cables Lay cables firmly in place by following the instructions below. Note1: Do not bind the cable for the radar collectively with cables of other equipment (especially power supply cable). Note2: Leave clearance near the inlet of the display so you can remove the display unit easily. This facilitates installation and maintenance of the display unit. (Refer to Appendix.) Note3: Because the cable has a connector fitted on the display and scanner side, if it is necessary to pass cable through a narrow path, fix the scanner-side connector vertically using vinyl tape before passing cable through the path. Note4: Lay cable along the ship's hull or wall surface and attach it in place at intervals of about 40 cm. 3.7.1 Interconnecting cable (See Fig.3-9) • Ensure that the radar is off. Connect the cable to the socket labeled "SCANNER" on the rear panel of the display unit. ‚ Use a T-wrench to remove the back covers of scanner unit. 22 ƒ Remove the two bolts securing the transceiver; pull out the transceiver after removing two connectors.(to Motor(J5), to Heading switch (J3) ) „ Remove the four bolts securing the fixing plate at the cable entrance. … Remove the metal fixing plate, rubber seal and washer that secure the cable. Pass the cable through as shown in the diagram below; replace the above items and tighten the bolts. † Return the transceiver to its original position and secure it with the removed bolts. ‡ Connect 7-pin connector to J2 and 9-pin connector to J1 of PCB. And connect two connectors that were removed at ƒ. ˆ Refit the scanner covers. Take care not to pinch the cable when refitting the cover. Fig.3-9 Interconnecting cable 23 3.7.2 Grounding wire WARNING Connect grounding wire before connecting power supply cable. Leakage current is too high. Connect grounding wire from the grounding terminal on the rear panel of the display unit to the ship's hull as shown below. Fig.3-10 Grounding display unit to earth Connect grounding wire from one of the bolts you have attached when installing the scanner unit to the ship's hull as shown in Fig.3-11. (The crimp terminal and grounding wire are not included with the radar equipment.) Scanner cover Grounding wire →To ship’s hull Fig.3-11 Grounding scanner unit to earth 24 3.7.3 Power supply cable Power is fed through a knife switch ( or circuit breaker) and protective fuses, as shown in below. Main switch panel (Knife Switch with Fuses) WARNING: Do not apply over 41.6V to Radar or Radar may be broken. Generator Switchboard Charger Storage Battery 12/24V Radar Display Unit DC voltage reference points Fit the power supply cable (included with your radar) to the receptacle labeled "POWER" on the rear panel of the display unit. And connect to power supply as follows. (When you do not connect external equipment, put tape on red and green wire.) Place the Fuse and connection part where there is no water splashes and the area is dry. If you extend the power supply cable, use a suitable cable as below. Ship's Power Voltage 12Vdc 24Vdc Cable conductor cross section 3.5 mm2 6.0 mm2 2.0 mm2 3.5 mm2 Cable max. length 3m 5m 6m 10 m Red Green Power supply cable To display unit Gray Black White NMEA+ NMEA- To external equipment Ground DCDC+ To power supply Fig.3-12 Power supply cable 3.8 Adjustment CAUTION Be sure to operate the following adjustment. If this is not adjusted properly, the radar picture does not display true image. When you have finished installing the scanner and display units and connecting cables, turn on the power to the display and scanner units and check to see if they operate normally without problem. Then make adjustments as detailed below and check to see if the units operate normally again. 1. TUNING 2. HEADING DIRECTION 3. DISTANCE Refer to Adjusting tuning circuit in 5.5.4.5.5 Refer to Adjusting angle in 5.5.4.5.5 Refer to Adjusting distance in 5.5.4.5.5 25 3.9 Connecting External Equipment to Display Unit The display unit has two channels of NMEA input. One is standard in power cable. The other is necessary to connect optional parts (Junction box with OPTION cable). OPTION connector is located at display’s rear panel for connecting external equipment such as a GPS, LORAN, or gyro compass. You must have a Junction box with OPTION cable. (Refer to CHAPTER 8 (4) External interface.) Note: SIN/COS and MOB signals cannot be used on Junction Box. POWER cable Junction box* (RZ704A) note To power supply OPTION cable Other radar, slave monitor, External buzzer, Gyro I/F External NMEA equipment (GPS,LORAN,etc.) Other radar, slave monitor, External buzzer, Gyro I/F, SIN/COS. MOB(NMEA out) Green Red :NMEA:NMEA+ External NMEA equipment (GPS,LORAN,etc.) * Junction box with OPTION cable (Order No. RZ704A) Fig.3-13 Connecting external equipment to display unit 3.10 Countermeasure for Electromagnetic Interference RA53/54 radar provides shields in the units and the inter-unit connection cable. When the radar, however, is closely installed to radio equipment such as VHF transceiver, UHF transceiver, etc., or the radar and/or radio equipment are not sufficiently grounded to the hull or ship's earth, the radar may happen to cause EMI trouble. Followings are general procedures for reducing EMI due to radars. When installing radars, refer to them, and also check the radio equipment EMI trouble with operating the radar and radio equipment. 26 (1) Installation Place of Radar The display unit, scanner unit and inter-unit connection cable should be located apart from the main unit, feeder, antenna coupler and antenna of radio equipment as far as possible. Especially, proper installation of the feeder, antenna coupler and antenna of radio equipment is very important to improve EMI trouble. (2) Laying Power Supply Cables Following connections A and B are recommended to reduce conduction noise generated from radar. Connection C should not be used. Connection A (Very Good) Connection B (Good) Connection C (Bad) RADAR SHIP'S SUPPLY RADIO EQUIPMENT SHIP'S SUPPLY RADAR SHIP'S SUPPLY RADIO EQUIPMENT SHIP'S SUPPLY RADAR RADIO EQUIPMENT (3) Grounding All equipment should be firmly grounded at the earth nearest hull with copper plates or braided wires. Improvement Procedure for EMI (1) Confirm grounding on the radar and radio equipment. However, some equipment, on which grounding is not always necessary, have a possibility of EMI improving when taking off their grounding. Try to take off grounding. (2) Confirm power supply cable connections and modify to the connection A or B above. (3) Try to shift the display unit and inter-unit connection cable of radar to be apart from radio equipment. (4) Try to shift the feeder of radio equipment to be apart from each units and the inter-unit connection cable of radar. (5) Try to shift the antenna coupler and antenna of radio equipment to be apart from the scanner unit and inter-unit connection cable of radar. 3.11 When Discarding Your Radar When discarding your RA53/54 radar, consult the distributor to get information on precautions to be followed. Tab.3-6 below lists the primary component materials of the RA53/54 radar for your reference. Tab.3-6 Component Materials Scanner unit Radome Chassis Base Antenna Display unit Front panel Rear panel Pedestal Material AES A5052P ADC12 A5052P 27 Material ABS ADC12 ABS+PC
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 27 Creator : OME_RA5354_1of4.rtf - Microsoft Word Create Date : 2001:08:29 15:33:30 Title : OME_RA5354_1of4.PDF Author : 109983 Producer : Acrobat PDFWriter 4.0 Windows NTEXIF Metadata provided by EXIF.tools