Kustom Signals CCBAS 900MHz Spread Spectrum Transceiver User Manual Manual Rev1
Kustom Signals Inc 900MHz Spread Spectrum Transceiver Manual Rev1
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 760523 |
| Application ID | TuKwX4Uydwqvs45plJx0Yw== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 5.04kB (62952 bits) |
| Date Submitted | 2007-02-19 00:00:00 |
| Date Available | 2007-02-19 00:00:00 |
| Creation Date | 2007-02-15 17:23:49 |
| Producing Software | Acrobat Distiller 6.0 (Windows) |
| Document Lastmod | 2007-02-15 17:24:24 |
| Document Title | Microsoft Word - Manual Rev1.doc |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | douglas |
006-0799-00 Rev 1 Digital Wireless Audio DSS Operating Instructions The Digital Wireless Audio DSS system is a digital frequency-agile radio designed to achieve excellent audio recording for the various Eyewitness Video systems. Transceiver Setup The Digital Wireless Audio DSS transceiver can be worn on a duty belt using the supplied pouch, or without the pouch, it can be worn/attached to an epaulet using the integrated clip. The epaulet clip remains on the transceiver even if the pouch is used – it will fit easily within the pouch. The transceiver can be used with or without the supplied mic cord. There is an internal mic on the transceiver that will be used if you do not use the cord, or if the cord becomes damaged. For best results, we recommend you use the cord. When you plug it in, route the cord downward as shown, so the strap will hold the plug securely in place. Base Station Setup The base station should be mounted according to the installation instructions (007-0798-00) found in the base station installation kit. You will need to attach the two antennas, then mount and connect the cable. For best reception, the antennas should be perpendicular to the ground. Operation Place the Transceiver (Mic) unit in the Base Unit (Base). This will “sync” the two devices. This sync will remain until the Mic is placed in a different Base or until a new Mic is placed in the Base. The last synchronization performed will override all earlier syncs. Under normal conditions, leaving the Mic in the Base will also charge the Mic, but there is no other need to place the Mic into the Base. After “syncing” is complete, the operation is very simple. The Mic has a blue slide switch that is used to either 1) activate the audio system and start the video recording, or 2) to mute the audio while in the record mode. When audio is activated, you will feel a short “buzz” from the internal vibrator motor, and the LED’s will change to indicate the active mode (see LED legend below). To mute the audio, slide the switch again – this will result in two short buzzes from the internal vibrator. When you stop a Recording by pressing the Stop button on the Control Center, the Digital Wireless Audio will automatically return to the standby mode. REMOTE TRANSCEIVER LED INDICATORS LED 1 (closest to switch) OFF LED 2 (middle) OFF LED 3 (closest to logo) OFF Vibrator N/A RED GREEN BLUE N/A GREEN GREEN BLUE 1 Long RED GREEN BLUE 2 Short RED RED BLUE N/A OFF OFF BLUE N/A Normal State Normal State Slow Blink BLUE N/A Blink GREEN GREEN Flashing RED OFF OFF OFF OFF OFF OFF N/A N/A N/A Status Power Switch OFF Pwr on, unit in Standby System active, Audio recording Standby or Muted No Comm with Base Station Battery Saver Mode** Battery is low recharging required. Charging Battery Charge Complete Charge Fault ** Battery Saver Mode is entered when the Remote has lost communication with the Base for 10 or more minutes. This is to conserve battery life when an Officer is out of range for an extended amount of time. Pressing the slide switch will exit this mode or the remote will exit it automatically when the Base Station signal is received. BASE STATION LED INDICATORS LED 1 LED 2 LED 3 Status N/A N/A BLUE Power is supplied to Base unit RED GREEN BLUE Remote is in Standby or Mute GREEN GREEN BLUE Remote Active and Audio is being recorded N/A Red then Flash GREEN then Solid GREEN BLUE Remote is in Base Station and “Association” is Complete Kustom Signals Inc. FCC ID: IVQCCRMT Model No. CCDSS-REM Tested To Comply with FCC Standards This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Kustom Signals Inc. FCC ID: IVQCCBAS Model No. CCDSS-BAS Tested To Comply with FCC Standards This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes not expressly approved by Kustom Signals voids the user's authority to operate the equipment. This product complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res Page Count : 3 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:ddc9da03-f2ff-4e7d-85b4-37ce7508cf5e Producer : Acrobat Distiller 6.0 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2007:02:15 17:24:24-08:00 Create Date : 2007:02:15 17:23:49-08:00 Metadata Date : 2007:02:15 17:24:24-08:00 Document ID : uuid:32148dd4-e920-4feb-9819-e2495647020e Format : application/pdf Title : Microsoft Word - Manual Rev1.doc Creator : douglas Author : douglasEXIF Metadata provided by EXIF.tools