Kyocera IUU19AB USB User Terminal of Wireless Internet System User Manual 1 of 2

Kyocera Corporation USB User Terminal of Wireless Internet System 1 of 2

Contents

User Manual 1 of 2

Download: Kyocera IUU19AB USB User Terminal of Wireless Internet System User Manual 1 of 2
Mirror Download [FCC.gov]Kyocera IUU19AB USB User Terminal of Wireless Internet System User Manual 1 of 2
Document ID706679
Application IDMhwy9jP88ln9+nn7/JJghA==
Document DescriptionUser Manual 1 of 2
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize182.45kB (2280617 bits)
Date Submitted2006-09-19 00:00:00
Date Available2006-09-19 00:00:00
Creation Date2006-08-21 20:12:24
Producing SoftwareAFPL Ghostscript 8.13
Document Lastmod2006-08-21 20:18:31
Document TitleMicrosoft Word - Q38T-EE-001_UTdUsersManualR101 for FCC.doc
Document CreatorPrimoPDF http://www.primopdf.com
Document Author: yamamoto

iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
Approved
Checked
Designed
Koyama
Yamamoto
Hirao
Reference:
Revision:
Date:
Kyocera Corporation
-1-
Q38T-EE-001
1.01
June.08.2006
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
Revision Record
Revision
1.00
1.01
Author
Hirao
Miyasaka
Kyocera Corporation
Date
May.10.2006
June.08.2006
Detail
First Release
Correct some writings
-2-
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
CONTENTS
Safety Precautions on iBurst Terminal................................
Terminal ................................................................
..........................................................................
.......................................... 4
Chapter 1 Introduction ................................................................
................................................................................................
..................................................................
.................................. 8
Components List ................................................................
................................................................................................
................................................................................................
................................................................................
................................................ 9
Pictures of Accessories ................................................................
................................................................................................
................................................................................................
.......................................................................
....................................... 9
Outlook of iBurst Terminal ................................................................
................................................................................................
..............................................................................................
.............................................................. 10
Indicators ................................................................
................................................................................................
................................................................................................
..........................................................................................
..........................................................11
.......................... 11
Requirements on your PC ................................................................
................................................................................................
................................................................................................
................................................................ 12
Outlook to use the iBurst Terminal................................
Terminal ................................................................
................................................................................................
..................................................................................
.................................................. 12
Chapter 2 Setup Procedure ................................................................
..........................................................................................
.......................................................... 13
iBurst Software Installation .............................................................................................................. 14
Installation for Windows XP ................................................................
................................................................................................
............................................................................................
............................................................ 14
Installation for Windows 2000 ................................................................
................................................................................................
.........................................................................................
......................................................... 17
Installation for Windows Me ................................................................
................................................................................................
............................................................................................
............................................................ 20
Installation for Windows 98SE................................
98SE ................................................................
................................................................................................
.........................................................................................
......................................................... 39
Installation for Mac OS X................................
X................................................................
................................................................................................
................................................................................................
.................................................................
................................. 59
Connection Establishment ................................................................................................................. 63
Connection Establishment for Windows XP ................................................................
................................................................................................
.....................................................................
..................................... 63
Connection Establishment for Windows 2000/Me/98SE ................................................................
...................................................................................
................................................... 68
Connection Establishment for Mac OS X ................................................................
................................................................................................
.........................................................................
......................................... 70
Chapter 3 Utility Software ................................................................
..........................................................................................
.......................................................... 74
Using Utility Software........................................................................................................................
75
Software
Using Utility Software for Windows................................
Windows ................................................................
................................................................................................
.................................................................................
................................................. 75
Using Utility Software for Mac OS X ................................................................
................................................................................................
...............................................................................
............................................... 81
Status Indication over Ethernet ........................................................................................................ 88
Chapter 4 MTU Optimizer Software & Network Property ..........................................
.......................................... 93
MTU Optimizer Software & Network Property................................................................................
94
Property
Chapter 5 Uninstallation
Uninstallation ................................................................
.............................................................................................
............................................................. 97
iBusrt Software Uninstallation..........................................................................................................
98
Uninstallation
Uninstallation for Windows XP/2000 ................................................................
................................................................................................
...............................................................................
............................................... 98
Uninstallation for Windows Me/98SE ................................................................
................................................................................................
.............................................................................
.............................................101
............. 101
Uninstallation for Mac OS X ................................................................
................................................................................................
...........................................................................................
...........................................................108
........................... 108
Chapter 6 Trouble shooting................................
shooting................................................................
.........................................................................................
.........................................................110
.........................110
Windows..............................................................................................................................................111
Windows
USB connection with Windows Me/98SE ................................................................
................................................................................................
........................................................................
........................................ 111
Illegal hanghang-up when install iBurst Terminal. ................................................................
................................................................................................
................................................................ 114
Illegal hanghang-up when set up dialer................................
dialer ................................................................
................................................................................................
..................................................................................
.................................................. 116
PC hanghang-up when eject iBurst Terminal from Win98 USB port. ................................................................
.....................................................................
..................................... 118
Mac ..................................................................................................................................................... 119
Data rate ................................................................
................................................................................................
................................................................................................
.........................................................................................
......................................................... 119
Chapter 7 Information ................................................................
...............................................................................................
............................................................... 120
FCC Compliance Statement.............................................................................................................
121
Statement
FCC RF Radiation Exposure Statement ......................................................................................... 121
Kyocera Corporation
-3-
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
Safety Precautions on iBurst Terminal
• Things you must know
•
•
•
When using the product, use it correctly according to the safety precautions.
The product uses particular radio frequency band tuned for the network operator.
The safety precautions, hardware, software, and the design of the product may be changed
in the future without any announcement to the customers.
• About use restriction
•
•
The product is designed as an OA apparatus for home use. Please use it neither in the
medical apparatus directly to affect a human life, nor the system of which very high
reliability is required.
Do not use the product in the zone where the wireless machines are forbidden, such as an
airplane and a hospital. An electric device and medical apparatus are affected and it
becomes the cause of the accident.
• About Qualification
•
•
•
•
•
•
•
•
Our company does not take any responsibility about the damage produced by use under
the conditions such as natural disasters, earthquake, flood, fires, misuse by intent or
carelessness or other than the responsibility of our company.
Our company does not take any responsibility about the damage produced by external
factor, failure, malfunction, and fault of product, such as loss of enterprise profits,
enterprise discontinuation, change and disappearance of the contents of memory etc.
Our company takes no responsibility about the damage produced by not keeping the
written contents of an owner's manual.
Our company takes no responsibility about the damage produced from incorrect operation
in combination with the connection apparatus and software in which our company is not
participating etc.
iBurst ™ is a registered trademark of ArrayComm, Inc.
Mac OS X is a registered trademark of Apple Computer, Inc.
Windows is a registered trademark of Microsoft Corporation.
In addition, the name of the software carried in this document and peripheral equipment is
each company’s trademark, or a registered trademark.
Kyocera Corporation
-4-
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
• For your safety
-------- Danger -------( If used improperly, may cause death or serious injury. )
•
•
•
•
•
•
•
•
•
•
•
•
Do not use with an abnormal condition, such as with emission of smoke or odor. It may
cause fire or electric shock.
Do not insert metal or flammable materials into the product interior through the air vents.
Pull out power plug from the outlet in case that foreign material into the product interior.
It may cause fire or electric shock.
Do not disassemble or remodel the product. It may cause fire or electrical shock.
Do not use or place the product at places with high humidity such as in the bath room or
near the humidifier. It may cause fire or electric shock. And do not touch the product with
wet hands.
Do not use the product with power supply other than AC100 to 240V. It may cause fire or
electric shock.
Do not plug too many leads into a single socket with extensions such as table taps, divided
outlets, and divided sockets. It may cause fire or electric shock. Moreover, make sure that
the total current does not exceed the capacity of the power supply. Otherwise, may cause
fire or electrical shock.
Do not damage, break, modify, bend, pull, twist, or bundle the AC cord. In addition, if a
heavy material is placed onto the cord or it is heated, the cord may break and cause fire or
electric shock.
Securely insert the plug into the outlet. If a metal object edges the teeth of the plug, it may
cause fire or electric shock. When pulling out the plug from the outlet, be sure to hold onto
its head. Pulling the cord can damage itself.
When you change the installation place of the product, pull out the plug from the outlet
and confirm that PC is completely separated from it. Otherwise, the cord may be damaged
and cause electric shock or fire.
Before inserting the plug into the outlet, check that there is no dust on its edge and head.
As dusts can easily enter between the plug and the outlet, they may cause fire or electric
shock. Pull out the plug from the outlet, at least once in a half year or a year, and
clean/maintenance.
Use the AC/DC adapter enclosed with the product. Usage of other AC/DC adapters may
cause fire or electric shock.
Do not place things or put cloth on the top of the plug. It may heat and break the plastic
and/or the rubber, causing fire or electric shock.
Kyocera Corporation
-5-
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
------- Warning -------( If used improperly, may cause disability or physical damage. )
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not give a shock strong against the product, such as dropping and throwing. It becomes
the cause of failure. Moreover, do not ride on the product. It may become the cause of an
injury.
Do not put the product under direct sunshine or near equipment with high temperature
such as a stove and a heater. It may raise the temperature of the interior and cause fire.
Do not put the product at places with an extreme fluctuation of temperature, such as near
the air conditioner or a heater. The dew condensation may occur in the interior and cause
fire, electrical shock, and malfunction.
Do not put the product at places with oil and steams such as in the kitchen. In addition, do
not put it at dusty places and places where metal powder and toxic gas occur. It may cause
fire or electric shock.
Do not place the product on unstable places such as on an unsteady desk or slanted
surfaces. In addition, do not put any object on the product. It may loose balance and
tumble, or fall and cause injury.
When the thunder occurs in near, do not use the product and its peripheral equipment. It
may become the cause of an electric shock.
If the air vents are blocked, the interior may be heated and cause malfunction. Please do
not use the products in the following manners;
Put on carpet or bedclothes.
Cover with tablecloths.
Put at places with bad ventilation, such as on a book shelf, in the drawer, or in the
closet.
If suspending the use for a long time, pull out the plug from the outlet.
Do not use the AC cord with an extension cord. It may cause fire.
For maintenance, pull out the AC plug from the outlet for safety. Do not wipe the product
with benzene, thinner, or alcohol. It may cause the product to decolorize or deform. If the
product be stained, put some neutral detergent on a dry cloth and wipe gently.
Do not connect electricity supplied LAN cable to the product. It may cause smoke or fire.
Do not touch the connector pins directly with your hands. Static electricity may affect the
components. As static electricity is created from both the cloth and the human body, before
putting or removing the product, release static electricity by touching a metal object such
as a small cabinet.
Do not use it in the intense place of vibration. It becomes the cause of failure.
Kyocera Corporation
-6-
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
-------- Caution -------( If treated improperly, the equipment may not perform or work properly. )
•
•
•
•
•
•
•
•
Do not put the product at low temperature. The product may not function properly.
Do not put the product on the top of magnetic objects and places where electromagnetic
waves occur. This includes electrical appliances, AV, and OA (microwave oven, speaker, TV,
radio, fluorescent light, inverter air conditioner, and electric kitchen appliances). The
product will not be able to make communication properly if effected by magnetism or
electronic noise. Putting the product near TV or radio may cause RF receive error.
The product lifetime may shorten if used at places with hydrogen sulfide such as at a hot
spring.
Data communication will be disabled or a data file may corrupt if the PC is turned off or
the product is separated from the PC during the communication. Important data must be
verified against the original data.
For fixing the product, use the enclosed fixture.
When connecting the product onto PC, use the enclosed USB cable or LAN cable.
Both a USB and an Ethernet interface cannot be used simultaneously in case a UTD
model.
When using UTD model, Please put the antenna at vertical position as shown in the below
diagrams so that the unit could acquire proper antenna characteristics.
Kyocera Corporation
-7-
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
Chapter 1 Introduction
This chapter describes what should
should be confirmed before
using iBurst Terminal.
Terminal.
Kyocera Corporation
-8-
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
Components List
The table below shows the list of components. Please confirm items in the package.
UTD model
Component
iBurst Terminal
AC/DC Adapter
Power Cable
USB Cable
10-Base-T Ethernet Cable
Notes
Q’ty
Q’ty
Unit of UTD model
Refer to the pictures shown in next page.
Input: 100 - 240V AC/ 50 - 60Hz/ 300mA
Output: 9V DC/ 1.2A
Cable Length of output side: 2m
Length: 2m
Type: USB1.1
Length: 1m
Type: Straight through/ Category 5
Length: 2m
UTU model
Component
iBurst Terminal
USB Cable
Notes
Q’ty
Q’ty
Unit of UTU model
Refer to the pictures shown in next page.
Type: USB1.1 (Mini B for UTU side)
Length: 1m
Pictures of Accessories
AC/DC Adapter
Kyocera Corporation
-9-
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
Outlook of iBurst Terminal
UTD model
Antenna
Power switch
Back side view
Power Indicator
Link/Communication Indicator
USB port
PC Connection Indicator
10Base-T port
only on UTD model
DC Power Input
Kyocera Corporation
- 10 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
UTU model
Link/Communication Indicator
Power Indicator
External antenna port
USB port
Indicators
Indicators
The table below describes meaning of each indicator.
Indicator
Power Indicator
Link/Communication Indicator
State
OFF
Blue
Blinking
OFF
Amber
Yellow
Green
PC Connection Indicator
(Only on UTD model)
Kyocera Corporation
OFF
Amber
Green
Meaning
Turned OFF
Turned ON
Fault
Turned OFF
No signal receiving
Weak signal receiving
Blinking when communicating.
Strong signal receiving
Blinking when communicating.
Any port not active
USB port
10Base-T port
- 11 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
Requirements on your PC
•
PC/AT Compatible PC with WindowsXP/2000/Me/98SE; or
version 10.1.5 or later version of Mac OS X except Mac Intel model.
•
1 USB1.1 port or a later version of USB port.
NOTE:
•
In case of using USB connection.
1 10Base-T Ethernet port or compatible.
NOTE:
In case of using 10Base-T Ethernet connection with a UTD model.
Outlook to use the iBurst Terminal
A UTD model has 1 USB port and 1 10Base-T Ethernet port and a UTU model has only 1 USB port.
The USB port, or 10Base-T Ethernet port, shall be connected with your PC. Before connecting the
USB interface, you have to install iBurst software which includes device drivers. If you want to
utilize 10Base-T connection, you don’t have to install the software in case Windows XP or Mac OS
X. Please read through every sections related with the operating system for details.
USB Connection
Back side of UTD
UTU
USB port
USB Cable
10Base-T Ethernet Connection
10Base-T port
Category 5 Cable
(Straight cable)
Kyocera Corporation
- 12 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
Chapter 2 Setup Procedure
This
This chapter describes how to install iBurst software, then
guides you how to make a network connection so as to use
data communication service.
Kyocera Corporation
- 13 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
iBurst Software Installation
Installation
This section shows the procedure to install iBurst software on your PC for utilizing iBurst
Terminal. The procedure shall be done once before using it.
Installation
Installation for Windows XP
NOTE:
If you are going to connect the iBurst Terminal with your PC only through an Ethernet cable, not
through a USB cable, you don’t need to install/uninstall any iBurst software. In such case, you
can skip this section and you need only to create a dial-up connection setting described at from
page 62. You can see indications of the iBurst Terminal over Ethernet. See page 87 for the
method.
1. Make sure to disconnect the iBurst Terminal with your PC.
ATTENTION:
Don’
Don’t connect the iBurst Terminal with your PC through a USB cable until completion of
installation.
2. Turn your PC on.
3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or
execute the appropriate installation software.
4. iBurst Terminal Setup starts. Click the [Next >] button.
Kyocera Corporation
- 14 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
5. Select [I accept the terms the license agreement], click the [Next >] button.
6. Click the [Next >] button after appearing dialog window as shown below.
NOTE:
To install to a different folder, click [Browse…] and specify another folder.
7. Click the [Next >] button.
Kyocera Corporation
- 15 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
8. The following dialog window will appear, and installation of software begins.
9. When the installing process finishes, the dialog window shown below will appear. Select “Yes, I
want to restart my computer now” and click the [Finish] button in the dialog window.
10. After finish of restarting, connect the iBurst Terminal with your PC’s USB port.
The iBurst Terminal will be recognized and will be ready to use automatically.
NOTE:
If the PC request to restart again, click [Yes] to restart the PC.
NOTE:
To connect to the Internet, refer to page 62.
Kyocera Corporation
- 16 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
Installation for Windows 2000
1. Make sure to disconnect the iBurst Terminal with your PC.
ATTENTION:
Don’
Don’t connect the iBurst Terminal with your PC through a USB cable until completion of
installation.
2. Turn your PC on.
3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or
execute the appropriate installation software.
4. iBurst Terminal Setup starts. Click the [Next >] button.
5. Select [I accept the terms the license agreement], click the [Next >] button.
Kyocera Corporation
- 17 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
6. Click the [Next >] button after appearing dialog window as shown below.
NOTE:
To install to a different folder, click [Browse…] and specify another folder.
7. Click the [Next >] button.
8. The following dialog window will appear, and installation of software begins.
Kyocera Corporation
- 18 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
9. When the installing process finishes, the dialog window shown below will appear. Select [Yes, I
want to restart my computer now] and click the [Finish] button in the dialog window.
10. After finish of restarting, connect the iBurst Terminal with your PC’s USB port.
The iBurst Terminal will be recognized and will be ready to use automatically.
NOTE:
If the PC request to restart again, click [Yes] to restart the PC.
NOTE:
To connect to the Internet, refer to page 67.
Kyocera Corporation
- 19 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
Installation for Windows Me
Me
Since the
the installation disk of Windows Me may be
be required while driver installation, please
prepare the CD or copy the CD into a hard disk in your PC for it.
1. Make sure to disconnect the iBurst Terminal with your PC.
ATTENTION:
Don’
Don’t connect the iBurst
iBurst Terminal with your PC through a USB cable until completion of
installation.
2. Turn your PC on.
3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or
execute the appropriate installation software.
4. iBurst Terminal Setup starts. Click the [Next >] button.
5. Select [I accept the terms the license agreement], click the [Next >] button.
Kyocera Corporation
- 20 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
6. Click the [Next >] button after appearing dialog window as shown below.
NOTE:
To install to a different folder, click [Browse…] and specify another folder.
7. Click the [Next >] button.
8. The following dialog window will appear, and installation of software begins.
Kyocera Corporation
- 21 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
9. Click the [Finish] button.
10. Click the [OK] button.
NOTE:
Refer to the 1st article in chapter 6, if you face such symptom described in the
attention message.
NOTE:
If you are going to connect the iBurst Terminal with your PC only through an Ethernet cable, not
through a USB cable, you can skip from hear to step 18 and continue from step 19 in this section.
You can see indications of the iBurst Terminal over Ethernet. See page 87 for the method.
11. Connect the iBurst Terminal with your PC through a USB cable.
Windows will detect the iBurst Terminal as a new hardware so that [Add New Hardware
Wizard] will begin.
Kyocera Corporation
- 22 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
12. Select [Specify the location of the driver (Advanced)] and click the [Next >] button in the dialog
window.
13. Select [Search for the best driver for your device.(Recommended)], then check [Specify a
location] and click the [Browse] button.
14. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button.
Kyocera Corporation
- 23 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
15. Click the [Next >] button.
16. Confirm that the device name [iBurst Terminal] is displayed in the dialog window, then click
the [Next >] button.
17. Click the [Finish] button.
Kyocera Corporation
- 24 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
18. The dialog window shown below will appear, click the [Yes] button, and restart your PC.
NOTE: If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times.
19. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and
then double click [Add New Hardware].
20. Click the [Next >] button.
Kyocera Corporation
- 25 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
21. Click the [Next >] button.
NOTE:
If the dialog window shown below appears, select [No, the device isn’t in the list]
and click the [Next >] button.
22. Select [No, I want to select the hardware from a list], and click the [Next >] button.
Kyocera Corporation
- 26 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
23. Select [Ports (COM & LPT)], and click the [Next >] button.
24. Click the [Have Disk..] button.
25. Click the [Browse...] button.
Kyocera Corporation
- 27 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
26. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button.
NOTE:
You don’t have to select a file name.
Windows will find an appropriate file
automatically.
27. Click the [OK] button.
28. Select [iBurst Terminal Virtual COM Port], and click the [Next >] button.
Kyocera Corporation
- 28 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
29. Click the [Next >] button.
30. Click the [Finish] button.
31. The dialog window shown below will appear, click the [Yes] button to SHUTDOWN your PC.
NOTE: If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times.
32. Turn your PC on again.
Kyocera Corporation
- 29 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
33. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and
then double click [Modems].
NOTE:
If the dialog window as shown below appears, click the [Add] button.
Kyocera Corporation
- 30 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
34. Check [Don’t detect my modem; I will select it from a list], and click the [Next >] button.
35. Click the [Have Disk..] button.
36. Click the [Browse…] button.
Kyocera Corporation
- 31 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
37. Select [C:\Program Files\iBurst Terminal\bin],and click the [OK] button.
NOTE:
You don’t have to select a file name.
Windows will find an appropriate file
automatically.
38. Click the [OK] button.
39. Select [iBurst Terminal Virtual MODEM], and click the [Next >] button.
Kyocera Corporation
- 32 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
40. Select [iBurst Terminal Virtual COM Port (COM X)], and click the [Next >] button.
NOTE:
The ‘X’ in “COM X” above is a COM port number assigned automatically.
NOTE:
If the dialog window as shown below appears, type a dummy number in “What
are (or city) code are you in now ?” and then click the [Next >] button.
41. Click the [Finish] button.
Kyocera Corporation
- 33 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
42. Click the [OK] button.
43. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and
then double click [Network].
Kyocera Corporation
- 34 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
44. Click the [Add…] button on [Configuration] tab.
45. Select [Protocol] and click the [Add…] button.
46. Click the [Have Disk…] button.
Kyocera Corporation
- 35 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
47. Click the [Browse…] button.
48. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button.
NOTE:
You don’t have to select a file name.
Windows will find an appropriate file
automatically.
49. Click the [OK] button.
Kyocera Corporation
- 36 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
50. Select [NDIS(PPPoE) Usermode I/O Protocol for iBurst Terminal], click the [OK] button.
NOTE:
If the same dialog at step 46 is popped up again, cancel once and repeat from step
44.
51. Click the [OK] button.
NOTE:
For USB connection with iBurst Terminal, “NDIS(PPPoE) User mode I/O Protocol
for iBurst Terminal -> iBurst Terminal” must be added automatically.
For Ethernet connection with iBurst Terminal, “NDIS(PPPoE) User mode I/O
Protocol for iBurst Terminal -> The name of the Ethernet Network Interface Card
or Port” shall be added automatically.
Kyocera Corporation
- 37 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
52. The dialog window shown below will appear, click the [Yes] button, and restart your PC.
NOTE:
If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times.
NOTE:
To connect to the Internet, refer to page 67.
Kyocera Corporation
- 38 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
Installation for Windows 98SE
Since the
the installation disk of WINDOWS 98SE may be required while driver installation, please
prepare the CD or copy the CD into a hard disk in your PC for it.
1. Make sure to disconnect the iBurst Terminal with your PC.
ATTENTION:
Don’
Don’t connect the iBurst Terminal with your PC through a USB cable until completion of
installation.
2. Turn your PC on.
3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or
execute the appropriate installation software.
4. iBurst Terminal Setup starts. Click the [Next >] button.
5. Select [I accept the terms the license agreement], click the [Next >] button.
Kyocera Corporation
- 39 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
6. Click the [Next >] button after appearing dialog window as shown below.
NOTE:
To install to a different folder, click [Browse…] and specify another folder.
7. Click the [Next >] button.
8. The following dialog window will appear, and installation of software begins.
Kyocera Corporation
- 40 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
9. Click the [Finish] button.
10. Click the [OK] button.
NOTE:
Refer to the 1st article in chapter 6, if you face such symptom described in the
attention message.
NOTE:
If you are going to connect the iBurst Terminal with your PC only through an Ethernet cable, not
through a USB cable, you can skip from hear to step 19 and continue from step 20 in this section.
You can see indications of the iBurst Terminal over Ethernet. See page 87 for the method.
11. Connect the iBurst Terminal with your PC through a USB cable.
Windows will detect the iBurst Terminal as a new hardware so that [Add New Hardware
Wizard] will begin.
Kyocera Corporation
- 41 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
12. Click the [Next >] button in the dialog window.
13. Select [Search for the best driver for your device.(Recommended)], and then check the [Next >]
button.
14. Check [Specify a location] and click the [Browse] button.
Kyocera Corporation
- 42 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
15. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button.
16. Click the [Next >] button.
17. Confirm that the device name [iBurst Terminal] is displayed in the dialog window, then click
the [Next >] button.
Kyocera Corporation
- 43 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
NOTE:
If the dialog window as shown below appears, insert [Windows 98SE CD-ROM]
into the CD-ROM drive and click the [OK] button.
NOTE:
If the dialog window as shown below appears, insert [Windows 98SE CD-ROM]
into your PC and enter the directory of your [Windows 98SE CD-ROM], click the
[OK] button. “xxxxxxxx“ in the picture below is a file name that can not be
found.
18. Click the [Finish] button.
19. The dialog window shown below will appear, click the [Yes] button, and restart your PC.
NOTE: If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times.
Kyocera Corporation
- 44 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
20. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and
then double click [Add New Hardware].
21. Click the [Next >] button.
22. Click the [Next >] button.
Kyocera Corporation
- 45 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
NOTE: If the dialog window as shown below appears, select [No, the device isn’t in the
list] and click the [Next >] button.
23. Select [No, I want to select the hardware from a list.], and click the [Next >] button.
24. Select [Ports (COM & LPT]], and click the [Next >] button.
Kyocera Corporation
- 46 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
25. Click the [Have Disk..] button.
26. Click the [Browse…] button.
27. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button.
NOTE:
You don’t have to select a file name.
Windows will find an appropriate file
automatically.
Kyocera Corporation
- 47 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
28. Click the [OK] button.
29. Select [iBurst Terminal Virtual COM Port], and click the [Next >] button.
30. Click the [Next >] button.
Kyocera Corporation
- 48 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
NOTE:
If the dialog window as shown below appears, insert [Windows 98SE CD-ROM]
into the CD-ROM drive and click the [OK] button.
NOTE:
If the dialog window as shown below appears, insert [Windows 98SE CD-ROM]
into your PC and enter the directory of your [Windows 98SE CD-ROM],click the
[OK] button. “xxxxxxxx“ in the picture below is a file name that can not be
found.
31. Click the [Finish] button.
32. The dialog window shown below will appear, click the [Yes] button to SHUTDOWN your PC.
NOTE: If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times.
Kyocera Corporation
- 49 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
33. Turn your PC on again.
34. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and
then double click [Modems].
NOTE:
If the dialog window as shown below appears, click the [Add] button.
Kyocera Corporation
- 50 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
35. Select [Other], and click the [Next >] button.
36. Check [Don’t detect my modem, I will select it from a list] and click the [Next >] button.
37. Click the [Have Disk…] button.
Kyocera Corporation
- 51 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
38. Click the [Browse…] button.
39. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button.
NOTE:
You don’t have to select a file name.
Windows will find an appropriate file
automatically.
40. Click the [OK] button.
41. Select [iBurst Terminal Virtual MODEM], and click the [Next >] button.
Kyocera Corporation
- 52 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
42. Select [iBurst Terminal Virtual COM Port (COM X)], and click the [Next >] button.
NOTE:
The ‘X’ in “COM X” above is a COM port number assigned automatically.
NOTE:
If the dialog window as shown below appears, type a dummy number in “What
are (or city) code are you in now ?” and then click the [Next >] button.
43. Click the [Finish] button.
Kyocera Corporation
- 53 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
44. Click the [OK] button.
45. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and
then double click [Network].
Kyocera Corporation
- 54 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
46. Click the [Add] button on [Configuration] tab.
47. Select [Protocol] and click the [Add…] button.
48. Click the [Have Disk…] button.
Kyocera Corporation
- 55 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
49. Click the [Browse…] button.
50. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button.
NOTE:
You don’t have to select a file name.
Windows will find an appropriate file
automatically.
51. Click the [OK] button.
Kyocera Corporation
- 56 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
52. Select [NDIS(PPPoE) Usermode I/O Protocol for iBurst Terminal], click the [OK] button.
NOTE:
If the same dialog at step 47 is popped up again, cancel once and repeat from step
45.
53. Click the [OK] button.
NOTE:
For USB connection with iBurst Terminal, “NDIS(PPPoE) User mode I/O Protocol
for iBurst Terminal -> iBurst Terminal” must be added in this stage.
For Ethernet connection with iBurst Terminal, “NDIS(PPPoE) User mode I/O
Protocol for iBurst Terminal -> The name of the Ethernet Network Interface Card
or Port” shall be added in this stage.
Kyocera Corporation
- 57 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
NOTE:
If the dialog window as shown below appears, insert [Windows 98SE CD-ROM]
into the CD-ROM drive and click the [OK] button.
NOTE:
If the dialog window as shown below appears, insert [Windows 98SE CD-ROM]
into your PC and enter the directory of your [Windows 98SE CD-ROM],click the
[OK] button. “xxxxxxxx“ in the picture below is a file name that can not be
found.
54. The dialog window shown below will appear, click the [Yes] button, and shut down your PC,
then turn on your PC again.
NOTE:
If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times.
NOTE:
To connect to the Internet, refer to page 67.
Kyocera Corporation
- 58 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
Installation for Mac OS X
NOTE:
If you are going to connect the iBurst Terminal with your PC only through an Ethernet cable, not
through a USB cable, you don’t need to install/uninstall any iBurst software. In such case, you
can skip this section and you need only to create a dial-up connection setting described at from
page 69. Please note that you cannot utilize the iBurst utility software described in chapter 3.
NOTE:
The installation software are applied to Mac OS X 10.1.5/10.2/10.3/10.4 except Mac Intel models.
Make sure OS version on your PC and a corresponding installation software package for iBurst
Terminal.
NOTE:
All screen copies in this section are based on Mac OS X 10.1.5.
1. Make sure to disconnect the iBurst Terminal with your PC.
ATTENTION:
Don’
Don’t connect the iBurst Terminal with your PC through a USB cable until completion of
installation.
2. Turn your PC on and login as an administrative user.
3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or
execute the appropriate installation software.
NOTE: If the window shown below appears, click “Click the lock to make changes”.
Kyocera Corporation
- 59 -
Revision 1.01 --- June.08.2006
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual
4. In case of version 10.3 or later, the confirmation message shown below will appear.
Click [Continue] button.
5. In case of version 10.2 or older, “Authenticate” dialog will appear.
Enter an administrator name and password, and then click the [OK] button.
6. Click the [Continue] button.
Kyocera Corporation
- 60 -
Revision 1.01 --- June.08.2006

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 60
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-14, framework 1.6
About                           : uuid:f93ef4c3-84cc-43a0-b501-fcf4d70fcbfb
Producer                        : AFPL Ghostscript 8.13
Modify Date                     : 2006:08:21 20:18:31+09:00
Create Date                     : 2006:08:21 20:12:24Z
Creator Tool                    : PrimoPDF http://www.primopdf.com
Metadata Date                   : 2006:08:21 20:18:31+09:00
Document ID                     : uuid:b91ac915-9cf0-4c26-9a3a-64985a994bf5
Format                          : application/pdf
Title                           : Microsoft Word - Q38T-EE-001_UTdUsersManualR101 for FCC.doc
Creator                         : yamamoto
Author                          : yamamoto
EXIF Metadata provided by EXIF.tools
FCC ID Filing: JOYIUU19AB

Navigation menu