LANKE XUNTONG TECHNOLOGY PTR5618PA Bletooth low energy 4.0 modules User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3214483
Application ID	jKVfzkjLpy59MD6uUh1fWA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	32.01kB (400184 bits)
Date Submitted	2016-12-01 00:00:00
Date Available	2016-12-01 00:00:00
Creation Date	2016-11-29 17:12:56
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2016-11-29 17:12:58
Document Title	Users Manual
Document Creator	Acrobat PDFMaker 11 Word 版
Document Author:	MCU

PTR5618PA
Coin-size Bluetooth Low Energy System on Module with PA
Embedded Cortex™ M4F 32 bit processor
The PTR5618PA ultra-low power Bluetooth Low Energy/2.4GHz Proprietary Multi-protocol
modules based on the nRF52832 from Nordic Semiconductor. The module with an ARM®
Cortex™ M4F 32 bit processor, embedded 2.4GHz transceiver, and integrated antenna,
provide a complete solution with no additional RF design, allowing faster time to market,
while simplifying designs, reducing BOM costs, also reduce the burden of Regulatory
approvals to enter the world market. Making you more quickly into the bluetooth smart
application and remove the worries.
Features

System on Module(SOM) base on Nordic nRF52832

Bluetooth Low Energy/2.4GHz Proprietary Multi-protocol support

Complete Bluetooth Low Energy stack/profiles solution (Bluetooth 4.x and Higher)

ARM® Cortex™-M4F 32 bit processor, 512 kB flash memory, 64 kB RAM

2.4 GHz transceiver, Max TX Power +15 dBm, -96 dBm sensitivity@BLE

11 General Purpose I/O, Configurable mapping Pins, Simple layout of external application

12-bit/200KSPS ADC, PWM, SPI Master/Slave (8 Mbps)

Low power comparator, Temperature sensor, Random Number Generator

Two 2-wire Master/Slave (I2C compatible)

I2S audio interface, PDM audio interface

UART (w/ CTS/RTS and DMA)

20 channel CPU independent Programmable Peripheral Interconnect (PPI)

Quadrature Demodulator (QDEC)

128-bit AES HW encryption

5 x 32bit Timers, 3 x 24bit Real Timer Counters (RTC), Watchdog Timer

Internal RC Oscillator 32.768 kHz(± 250 ppm).

No external components required

Over-the-Air (OTA) firmware updates available

Ultra small size(smaller than CR2032 coin battery), about 15mmx15mmx1.8mm.
COPYRIGHT ©2016 ALL RIGHTS RESERVED
XunTong Tech
TEL: +86 755 26675941
E-mail: nrf@freqchina.com
Typical Applications:
















- 2.4 GHz Bluetooth low energy systems
- Proprietary 2.4 GHz systems
- Sports and leisure equipment
- Mobile phone accessories
- Health Care and Medical
- Consumer Electronics, Game pads
- Human Interface Devices, Remote control
- Building environment control / monitoring
- RFID, Security Applications
- Bluetooth Low Energy GateWay
- iBeacons™, Eddystone™, Indoor navigation
- Low-Power Sensors
- Connected Appliances
- Lighting Products
- Fitness devices
- Wearables
Quick Specifications:
Multi-protocol
Version
Bluetooth 4.x and Higher/ANT/2.4GHz Proprietary
Security
AES-128
Radio
Frequency
2.402GHz to 2.480GHz
Modulations
GFSK at 1 Mbps, 2 Mbps data rates
Transmit power
Max +15dBm @setting nRF52832 0dBm output
Receiver sensitivity
-96dBm (BLE mode)
Antenna
IPX interface
Current Consumption
TX only @ +15 dBm
~100 mA
RX only @ 1 Mbps @ 3V, DC/DC enabled
~5.4 mA
RX only @ 1 Mbps
~11.7 mA
CPU @ 64MHz from flash
7.5 mA
CPU @ 64MHz from RAM
6.7 mA
CPU @ 64MHz from flash @ 3V, DC/DC
3.7 mA
CPU @ 64MHz from flash RAM @ 3V, DC/DC
3.3 mA
System On
1.2 μA
System Off
0.7μA
Operating conditions
Power supply
2.7~3.6V
Operating temperature
-25~+85 °C
COPYRIGHT ©2016 ALL RIGHTS RESERVED
XunTong Tech
TEL: +86 755 26675941
E-mail: nrf@freqchina.com
Block diagram:
Pin Description of Module（Top View）:
Pin No.
10
11
12
13
Name
P0.11
P0.12
P0.13
SWDIO
SWDCLK
P0.17
P0.18
P0.21
GND
VDD
P0.26
P0.27
P0.28
Description
Note
I/O
I/O
I/O
Debug and flash programming I/O
Debug and flash programming I/O
I/O
I/O
Reset/ IO
Power Ground
Power Supply
I/O
I/O
I/O
COPYRIGHT ©2016 ALL RIGHTS RESERVED
XunTong Tech
Configurable as pin reset.
ADC IN
TEL: +86 755 26675941
E-mail: nrf@freqchina.com
14
15
P0.29
P0.30
I/O
I/O
ADC IN
ADC IN
Note 1: P0.20 and P0.24 are reserved for PA control internal.
Note 2: An internal 4.7μF bulk capacitor has been included on the module. it is good design
practice to add additional bulk capacitance(e.g 10uF) as required for your application.
General Purpose I/O:
The general purpose I/O is organized as one port enabling access and control of the 32 available
GPIO pins through one port. Each GPIO can be accessed individually with the following user
configurable features:
 Input/output direction
 Output drive strength
 Internal pull-up and pull-down resistors
 Wake-up from high or low level triggers on all pins
 Trigger interrupt on all pins
 All pins can be used by the PPI task/event system; the maximum number of pins that can be
interfaced through the PPI at the same time is limited by the number of GPIOTE channels
 All pins can be individually configured to carry serial interface or quadrature demodulator
signals
PA control:
Additional logic signals are needed to control TX PA and RX LNA. On the nRF51 there was an
option to use the VDD_PA pin to detect when the radio was in TX mode, but this is not an option on
the nRF52, making the SoftDevice solution necessary. The S132 SoftDevice for the nRF52 has
support for enable/disable switching of external Power Amplifiers (PA) and LNA using GPIO pins.
On the module, P0.20 and P0.24 are reserved to control PA and LNA, so these two pins can Not
be allocated to other usage.
The truth table of PA/LNA control signals as bellow:
PIN24 PIN20 PA status
TXEN
RXEN
IDLE
INVALID
The following function can be used to enable PA/LNA signal with P0.20 and P0.24. Add this
function to your project and call it after ble_stack_init():
static void pa_assist(uint32_t gpio_pa_pin,uint32_t gpio_lna_pin)
ret_code_t err_code;
COPYRIGHT ©2016 ALL RIGHTS RESERVED
XunTong Tech
TEL: +86 755 26675941
E-mail: nrf@freqchina.com
static const uint32_t gpio_toggle_ch = 0;
static const uint32_t ppi_set_ch = 0;
static const uint32_t ppi_clr_ch = 1;
// Configure SoftDevice PA assist
ble_opt_t opt;
memset(&opt, 0, sizeof(ble_opt_t));
// Common PA config
opt.common_opt.pa_lna.gpiote_ch_id
= gpio_toggle_ch;
// GPIOTE channel
opt.common_opt.pa_lna.ppi_ch_id_clr = ppi_set_ch;
opt.common_opt.pa_lna.ppi_ch_id_set = ppi_clr_ch;
// PPI channel for pin clearing
// PPI channel for pin setting
// PA config
opt.common_opt.pa_lna.pa_cfg.active_high = 1;
// Set the pin to be active high
opt.common_opt.pa_lna.pa_cfg.enable
= 1;
// Enable toggling
opt.common_opt.pa_lna.pa_cfg.gpio_pin
= gpio_pa_pin;
// The GPIO pin to toggle
opt.common_opt.pa_lna.lna_cfg.active_high
= 1;
opt.common_opt.pa_lna.lna_cfg.enable
= 1;
opt.common_opt.pa_lna.lna_cfg.gpio_pin
= gpio_lna_pin;
err_code = sd_ble_opt_set(BLE_COMMON_OPT_PA_LNA, &opt);
APP_ERROR_CHECK(err_code);
COPYRIGHT ©2016 ALL RIGHTS RESERVED
XunTong Tech
TEL: +86 755 26675941
E-mail: nrf@freqchina.com
The following main function is an example that to show you how to enable PA/LNA signal in your
project:
int main(void)
uint32_t err_code;
// Initialize.
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_OP_QUEUE_SIZE, false);
ble_stack_init();
pa_assist(24,20);
gap_params_init();
services_init();
advertising_init();
conn_params_init();
err_code = ble_advertising_start(BLE_ADV_MODE_FAST);
APP_ERROR_CHECK(err_code);
// Enter main loop.
for (;;)
power_manage();
COPYRIGHT ©2016 ALL RIGHTS RESERVED
XunTong Tech
TEL: +86 755 26675941
E-mail: nrf@freqchina.com
Hardware RESET:
There is on-chip power-on reset circuitry, But can still be used in external reset mode, in this case,
GPIO pin P0.21 as an external hardware reset pin(Active Low). In order to utilize P0.21 as a hardware
reset, the UICR registers PSELRESET[0] and PSELRESET[1] must be set alike, to the value of
0x7FFFFF15. When P0.21 is programmed as RESET, the internal pull-up is automatically enabled.
HW debug and flash programming of Module:
The Module support the two pin Serial Wire Debug (SWD) interface and offers flexible and powerful
mechanism for non-intrusive debugging of program code. Breakpoints, single stepping, and
instruction trace capture of code execution flow are part of this support.
Pin
Flash Program interface
SWDIO
Debug and flash programming I/O
SWCLK
Debug and flash programming I/O
This is the hardware debug and flash programming of module, J-Link Lite support, please refer
www.segger.com.
COPYRIGHT ©2016 ALL RIGHTS RESERVED
XunTong Tech
TEL: +86 755 26675941
E-mail: nrf@freqchina.com
PCB Footprint （Top View）:
Ordering Information:
Part Number
Description
PTR5618PA
Bluetooth Low Energy System on Module with PA
PTR5618PA-EVB
Evaluation boards for module，with key, LED, I/O extend，sock
for coin cell battery.
Absolute Maximum Ratings:
Symbol
VCC_MAX
VIO_MAX
VIO_MAX
TS
Parameter
Voltage on supply pin
Voltage on GPIO pins (VCC > 3.6V)
Voltage on GPIO pins (VCC ≤ 3.6V)
Storage Temperature Range
Min.
Max.
Unit
-0.3
-0.3
-0.3
-40
3.9
3.9
VCC + 0.3V
125
°C
Important Notice:



Reserves the right to make corrections, modifications, and/or improvements to the product and/or
its specifications at any time without notice.
Assumes no liability for the user’s product and/or applications.
Products are not authorized for use in safety-critical applications, including but not limited to
life-support applications.
ATTENTION!
Electrostatic Sensitive Device
Observe Precaution for handling.
COPYRIGHT ©2016 ALL RIGHTS RESERVED
XunTong Tech
TEL: +86 755 26675941
E-mail: nrf@freqchina.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : MCU
Create Date                     : 2016:11:29 17:12:56+08:00
Modify Date                     : 2016:11:29 17:12:58+08:00
Subject                         : 
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2016:11:29 17:12:58+08:00
Creator Tool                    : Acrobat PDFMaker 11 Word 版
Document ID                     : uuid:d4dc9557-0d2f-45e1-9ae4-902f529106ba
Instance ID                     : uuid:d226d3d6-b61b-43bb-958e-3f8b935272f7
Format                          : application/pdf
Title                           : 内置协议及链路层、具有六路接收通道
Description                     : 
Creator                         : MCU
Producer                        : Adobe PDF Library 11.0
Keywords                        : 
Source Modified                 : D:20161129091253
Company                         : Microsoft China
Page Layout                     : OneColumn
Page Count                      : 8

EXIF Metadata provided by EXIF.tools