LG Electronics USA 37LDB 37" LCD TV MONITOR User Manual User s Manual H ok
LG Electronics USA 37" LCD TV MONITOR User s Manual H ok
USERS MANUAL
Test Report No.: GETEC-E3-06-004 FCC Class B Certification APPENDIX H : USER’S MANUAL EUT Type: 37” LCD TV/Monitor FCC ID: BEJ37LDB 37LB1DA P/NO : 38289U0512F (0601-REV00) WARNING / CAUTION WARNING / CAUTION To prevent fire or shock hazards, do not expose this product to rain or moisture. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. WARNING / CAUTION FCC NOTICE TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. WARNING/CAUTION TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CAUTION Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product SAFETY INSTRUCTION IMPORTANT SAFETY INSTRUCTIONS SAFETY INSTRUCTION Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the apparatus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled “Important Safety Instructions”. The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction : Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Ow Do not use this apparatus near water Clean only with dry cloth. ne r's Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. an ua Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat. Only use attachments/accessories specified by the manufacturer. 8 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. 10 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped. 11 12 13 Outdoor Use Marking : WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Appliance To Rain Or Moisture SAFETY INSTRUCTION authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Wet Location Marking : Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on or over apparatus. CAUTION concerning the Power Cord : Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an ACCESSORIES Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product. INPUT TV INPUT TV AUDIO DVD MODE CABLE DAY MENU VCR STB DAY+ INFO i TV GUI DE ENTER EXIT SAP CC RATIO Owner’s Manual Batteries Remote Control D-sub 15 pin Cable 75ohm Round Cable 2-TV Bracket Bolts Twister Holder Arrange the wires with the twister holder. Power Cord INTRODUCTION POWER Owner's Manual 2-TV Brackets, 2-Wall Brackets Cable Management (Refer to p.15) INTRODUCTION CONTROLS This is a representation of the front panel of models 37LB1DA TVs. ■ Here shown may be somewhat different from your TV. INTRODUCTION Front Panel Controls TV GUIDE TV POWER TV GUIDE GUIDE INPUT Button Button Remote Control Sensor INPUT INPUT MENU Button VOL MENU MENU VOL Button VOLUME CH (F,G)Buttons CH CHANNEL (E,D)Buttons Power Standby Indicator Illuminates red in standby mode. When the TV is turned on, the indicator blinks white and then illuminates white before the picture is displayed. INDEX 10 Inserting the CableCARDs. Component mode HDTV mode RGB-PC mode AV mode HDMI1/DVI or HDMI2 mode CONNECTION OPTION This is a back panel of 37LB1DA. Back Connection Panel AUDIO R S-VIDEO VIDEO L/MONO Cable CARD ™ CableCARD Used for CableCARD™ Cable Service Provider. 10 S-VIDEO Input Provides better picture quality than the video input. AUDIO Input Connections are available for listening to stereo sound from an external device. VIDEO Input Connects the video signal from a video device. INTRODUCTION AV IN 2 AV OUTAV OUT VIDEO (MONO) VIDEO S-VIDEO AUDIO AUDIOAV IN 1 S-VIDEO AV IN 1 VIDEO AUDIO VIDEO COMPONENT IN AUDIO COMPONENT IN ANTENNA IN ANTENNA IN HDMI IN HDMI IN DIGITAL AUDIO OUT DIGITAL AUDIO OUT CABLE IN RS-232C IN (CONTROL & SERVICE) OPTICAL RS-232C IN (CONTROL & SERVICE) CABLE IN AUDIO IN (RGB/DVI) AUDIO IN (RGB/DVI) REMOTE CONTROL REMOTE CONTROL RGB IN (PC/DTV) OPTICAL PTICAL RGB IN (PC/DTV) AV OUT Connect a second TV or monitor. RS-232C IN (CONTROL & SERVICE) PORT Connect to the RS-232C port on a PC. AV (Audio/Video) IN 1 Connect audio/video output from an external device to these jacks. S-VIDEO Connect S-Video out from an S-VIDEO device. ANTENNA IN Connect over-the air signals to this jack. CABLE IN Connect cable signals to this jack. COMPONENT IN Connect a component video/audio device to these jacks. RGB/AUDIO IN Connect the monitor output from a PC to the appropriate input port. HDMI IN Connect a HDMI signal to 1(DVI) or 2. Or DVI(VIDEO)signal to the 1(DVI) port with a DVI to HDMI cable. Remote Control Port Connect your wired remote control. 10 Power Cord Socket For operation with AC power. Caution: Never attempt to operate the TV on DC power. DIGITAL AUDIO OUT Connect digital audio from various types of equipment. Note: In standby mode, these ports do not work. 11 INSTALLATION TO ATTACH THE TV TO A WALL We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV. INSTALLATION ■ Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture. *If your TV have bolts in the upper holes, loosen the bolts. Insert the eye-bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately ) on the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely. ■ 14 Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product. WIRE ARRANGEMENT This function explains the features available on the 37LB1DA. Connect the cables as necessary. After connecting the cables neatly, arrange the cables to the Cable Holder. To connect an additional equipment, see the External equipment Connections section. INSTALLATION CABLE HOLDER Install the CABLE MANAGEMENT as shown. CABLE MANAGEMENT How to remove the CABLE MANAGEMENT Hold the CABLE MANAGEMENT with both hands and pull it backward. Bundle the cables using the supplied twister holder. ! NOTE Do not hold the CABLE MANAGEMENT when moving the product. - If the product is dropped, you may be injured or the product may be broken. TWISTER HOLDER 15 INSTALLATION DESKTOP PEDESTAL INSTALLATION For proper ventilation, allow a clearance of 4inches on each side from the wall. 4 inches 4 inches 4 inches INSTALLATION 4 inches 4 inches CAUTION 16 Ensure adequate ventilation by following the clearance recommendations. AUTO LINK AV 2 Press the INPUT button and then displays the connected external equipment list on the screen. Press the ENTER button to change the main input to the active external equipment. Use the D or E button to select the main input source. Auto Link Antenna Cable AV 1 AV 2 Component1 When every external equipment is connected: Antenna HDMI2 Cable HDMI1/DVI RGB-DTV (or RGB-PC) Component1 Component2 Cable When some External Equipment is connected: (ex: When connected to AV 2) Antenna ■ AV2 When any external equipment is not connected: Antenna AV1 INSTALLATION Cable AV2 You can also select M a i n I n p u t in the S e t u p menu. EZ Scan Manual Scan Channel Edit DTV Signal Main Input Sub Input Input Label Set ID Antenna Cable AV 1 AV 2 Component1 Component2 RGB-PC HDMI1/DVI HDMI2 A n t e n n a: Select it when watching the TV/DTV. ■ C a b l e: Select it when watching the CATV/CADTV. ■ A V 1 - 2: Select it when watching the VCR or external equipment. ■ C o m p o n e n t 1 - 2: Select it when using the DVD or the Digital set-top box depend on connector. ■ R G B - P C / R G B - D T V: Select it when using PC or Digital set-top box depend on connector. ■ H D M I 1 / D V I , H D M I 2 : Select it when using DVD, PC or Digital set-top box depend on connector. ■ 17 CONNECTIONS & SETUP ANTENNA OR CABLE CONNECTION 1. Antenna (analog or digital) Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections. For optimum picture quality, adjust antenna direction if needed. INSTALLATION Wall Antenna Socket Multi-family Dwellings/Apartments (Connect to wall antenna socket) AV OUT CABLE CABLE IN IN ANTENNA IN VIDEO S-VIDEO AUDIO AV IN 1 VIDEO AUDIO COMPONENT IN ANTENNA IN CABLE IN Outdoor Antenna (VHF, UHF) RF Coaxial Wire (75 ohm) HDMI IN DIGITAL AUDIO OUT RS-232C IN (CONTROL & SERVICE) AUDIO IN (RGB/DVI) OPTICAL RGB IN (PC/DTV) Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) Bronze Wire Be careful not to bend the bronze wire when connecting the antenna. 2. Cable box Cable TV Wall Jack CABLE IN ANTENNA IN RF Coaxial Wire (75 ohm) CABLE IN 3. Using both cable and antenna ANTENNA IN Antenna RF Coaxial Wire (75 ohm) CABLE IN Cable TV Wall Jack RF Coaxial Wire (75 ohm) 18 CABLE CABLE IN IN CABLE IN REMOTE CONTROL UHF Antenna VHF Signal Amplifier ANTENNA IN To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly. ■ If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter. ■ If the antenna is not installed properly, contact your dealer for assistance. ■ ! NOTE The TV will let you know when the analog, cable, and digital channel scans are complete. CONNECTIONS & SETUP CABLE IN 19 CONNECTIONS & SETUP CABLECARDTM SETUP 1. How to use Insert the CableCARDTM from your cable service provider into the CableCARDTM slot on the back of your TV. If pairing information about this TV and the CableCARD is displayed on the screen, contact your cable service provider. CONNECTIONS & SETUP 20 ! NOTE This TV supports CableCARDTM technology from Motorola, Scientific Atlanta, and SCM. CAUTION When removing, do not drop it as this may cause damage to the CableCARDTM. Cable CARD Cable CARD HDSTB SETUP This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i). When connecting Component cable 1. How to connect PB PR Connect the audio output of the digital set-top box to the C O M P O N E N T I N V I D E O 1 jacks on the set. 2. How to use ■ Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) S-VIDEO VIDEO CONNECTIONS & SETUP Connect the video outputs (Y, PB, PR) of the digital set top box to the C O M P O N E N T I N V I D E O 1 jacks onthe set. Match the jack colors (Y = green, PB = blue, and PR = red). AUDIO UDIO COMPONENT IN ■ Select C O M P O N E N T 1 input source with using the I N P U T button on the remote control. ■ If connected to C O M P O N E N T 2 input, select C O M P O N E N T 2 input source. Signal Component 1/2 RGB-DTV, HDMI /DVI, HDMI2 480i Yes No 480p Yes Yes 720p Yes Yes 1080i Yes Yes ANTENNA IN CABLE IN 21 CONNECTIONS & SETUP When connecting D-sub 15pin cable ANTENNA IN 1. How to connect Connect the RGB output of the digital set-top box to the R G B ( P C / D T V) jack on the set. RGB IN CABLE IN REMOTE CONTROL IN AUDIO (RGB/DVI) RGB (PC/DTV) Connect the audio outputs of the set-top box to the A U D I O ( R G B / D V I) jack on the set. 2. How to use CONNECTIONS & SETUP ■ ■ Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) Select R G B - D T V input source with using the I N P U T button on the remote control. When connecting HDMI cable RGB INPUT 1. How to connect VIDEO Connect the digital set-top box to H D M I I N 1 ( D V I ) or 2 jack on the set. AUDIO COMPONENTNo IN separated audio connection is necessary. HDMI IN RS-2 DIGITAL AUDIO (CONTRO OUT OPTICAL ANTENNA IN 2. How to use ■ Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) ■ Select H D M I 1 / D V I or H D M I 2 input source with using the I N P U T button on the remote control. ■ If the digital set-top box supports Auto HDMI function, the output resolution of the source device will be automatically set to 1280x720p. ■ If the digital set-top box player does not support Auto HDMI, you need to set the output resolution appropriate ly. To get the best picture quality, adjust the output resolution of the source device to 1280x720p. 1(DVI) CABLE IN 22 HDMI-DTV OUTPUT When connecting HDMI to DVI cable ANTENNA IN RGB IN HDMI IN CABLE IN RS-232C IN DIGITAL AUDIO (CONTROL & SERVICE) OUT REMOTE CONTROL IN AUDIO (RGB/DVI) OPTICAL RGB (PC/DTV) 1(DVI) CONNECTIONS & SETUP DVI-DTV OUTPUT 1. How to connect Connect the DVI output of the digital set-top box to the H D M I I N 1 ( D V I ) jack on the set. Connect the audio output of the digital set-top box to the A U D I O ( R G B / D V I ) jack on the set. 2. How to use ■ Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) ■ Select H D M I 1 / D V I input source with using the I N P U T button on the remote control. 23 PC SETUP This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. If necessary, change the screen scanning rate for the graphic card accordingly. When connecting D-sub 15pin cable ANTENNA IN 1. How to connect Connect the RGB output of the PC to the R G B ( P C / D T V) jack on the set. RGB IN CABLE BLE IN Connect the PC audio output to the A U D I O ( R G B / D V I) jack on the set. RGB (PC/DTV) 2. How to use ■ Turn on the PC and the set. ■ Select R G B - P C input source in main input option of SETUP menu. (G p . 6 7) ■ Once you select R G B - P C in main input option of S E T U P menu, I N P U T button is also available for this purpose. CONNECTIONS & SETUP AUDIO (RGB/DVI) REMOTE CONTROL IN ! NOTE Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. AUDIO RGB OUTPUT 31 CONNECTIONS & SETUP When connecting HDMI to DVI cable ANTENNA IN RGB IN HDMI IN CABLE IN RS-232C IN DIGITAL AUDIO (CONTROL & SERVICE) OUT REMOTE CONTROL IN AUDIO (RGB/DVI) OPTICAL RGB (PC/DTV) 1(DVI) VI) CONNECTIONS & SETUP DVI-PC OUTPUT AUDIO 1. How to connect Connect the DVI output of the PC to the H D M I I N 1 ( D V I ) jack on the set. Connect the PC audio output to the A U D I O ( R G B / D V I ) jack on the set. 2. How to use ■ Turn on the PC and the set ■ Select H D M I 1 / D V I input source with using the I N P U T button on the remote control. ! NOTE 32 HDMI2 source does not support DVI source. If the PC has a DVI output and no HDMI output, a separated audio connection is necessary. If the PC does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of PC graphics card's output resolution to 1024x768, 60Hz. ! NOTES To get the the best picture quality, adjust the PC graphics card to 1024x768, 60Hz. Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use. When Source Devices are connected with HDMI/DVI Input, the output PC Resolution(VGA, SVGA, XGA), Position and Size may not fit on the Screen. As shown in the picture, press the ADJUST button to adjust the screen Position of the TV SET and contact a PC graphics card service center. When Source Devices connected with HDMI/DVI Input, output TV SET Resolution (480p, 720p, 1080i) and TV SET Display fit EIA/CEA-861-B Specification to Screen. If not, refer to the Manual Surpported Display Specifications (RGB/HDMI-PC) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 640x350 31.468 70.09 720x400 31.469 70.08 640x480 31.469 37.861 37.500 59.94 72.80 75.00 800x600 35.156 37.879 48.077 46.875 56.25 60.31 72.18 75.00 1024x768 48.363 56.476 60.023 60.00 70.06 75.02 1280x768 47.776 59.870 1360x768 47.720 59.799 If the HDMI/DVI Source Device is not connected to the Cable or if there is a poor cable connection, "No signal" is displayed in the HDMI/DVI Input. In this case, that Video Resolution is not supported. If "Invalid Format" is displayed, refer to the Source Device manual or contact your service center. Avoid keeping a fixed image on the screen for a long period of time. The fixed image may become permanently imprinted on the screen. The synchronization input form for Horizontal and Vertical frequencies is separate. Surpported Display Specifications (RGB/HDMI-DTV) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 720x480 31.47 31.47 60 59.94 1280x720 45.00 44.96 60.00 59.94 1920x1080 33.75 33.72 60.00 59.94 CONNECTIONS & SETUP of HDMI/DVI Source Devices or contact your service center. * RGB-PC mode only: 640x350, 720X400 * HDMI-PC mode only: 1280x768 33 Screen Setup for PC mode Overview When RGB connect to PC output and select the RGB-PC in Main Input, this function is used. When HDMI/DVI connect to PC output and select HDMI/DVI input, this function is used. In RGB-DTV mode, SIZE and PHASE is not available. FLASHBK PIP PIP CH - TIMER APM EZ PIC EZ SOUND PIP CH + PIP INPUT ADJUST SWAP Adjustment for screen Position, Size, Phase, Reset Position G Press the A D J U S T button and then use D or E button to select P o s i t i o n, S i z e, or P h a s e. Size BASIC OPERATION Phase Press the ENTER button and then use D E F make appropriate adjustments. ■ The P h a s e adjustment range is - 1 6 ~ + 1 6. ■ The S i z e adjustment range is - 3 0 ~ + 3 0. Press the ENTER button. Initializing (Reset to original factory values) To initialize the adjusted values Reset button to Adjust Close Position This function is to adjust picture to left/right and up/down as you prefer. Size This function is to minimize any vertical bars or stripes visible on the screen background. And the horizontal screen size will also change. Phase This function allows you to remove any horizontal noise and clear or sharpen the image of characters. In HDMI/DVI-PC mode, PHASE is not available. Press the A D J U S T button and then use D or E button to select R e s e t. Position Size Phase Press the ENTER button and then use F or G button to select Y e s. 34 Press the ENTER button. Yes No Reset G Adjust Initialize Settings Previous Move Select APPENDIX EXTERNAL CONTROL DEVICE SETUP Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Connect the serial port of the control device to the RS-232C jack on the product back panel. Note: RS-232C connection cables are not supplied with the product. RS-232C Setup HDMI/DVI IN RS-232C IN DIGITAL AUDIO (CONTROL & SERVICE) OUT OPTICAL 1(DVI) Type of Connector; D-Sub 9-Pin Male APPENDIX 108 No. Pin Name No connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection PROGRAMMING THE REMOTE CONTROL The provided universal remote control can be programmed to operate most remote-controllable devices. Note that the remote may not control all models of other brands. Programming a code into a remote mode To find out whether your remote control can operate each device without programming, turn on the device (such as a VCR) and press the corresponding mode button on the remote. After that, press the POWER button. If the device is turned off and it responds properly the remote control need not be programmed. If not, the remote should be programmed to operate the device. The programming procedures are explained below. Press the M E N U and M U T E button continuously at the same time for two seconds; the currently selected device button is illuminated. If you don't press any button for 20 seconds, the light on the mode button will be turned off. In that case, you have to repeat from step 2. Enter the appropriate code from the code table on the following pages. When pressing the button, the light blinks at a time. If the device turned off, the programming is successful. Press the M E N U button to store the code. After blinking twice, this code is stored. Test the remote control functions to see if the device responds properly. If not, steps 2-5. APPENDIX 117 PRODUCT SPECIFICATIONS 37LB1DA (37LB1DA-UB) MODELS including stand Dimensions (Width x Height x Depth) 41.2 x 27.3 x 10.3 inches 1045.8 x 693.8 x 260.4 mm excluding stand 41.2 x 23.4 x 5.2 inches 1045.8 x 594.4 x 133.0 mm Weight including stand 69.7 pounds / 31.6 kg excluding stand 55.8 pounds / 25.3 kg AC100-240V ~ 50/60Hz Power requirement Television System NTSC-M, ATSC, 64 & 256 QAM Program Coverage VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135 75 ohm External Antenna Impedance Operating Temperature 32 ~ 104°F (0 ~ 40°C) Operating Humidity Less than 80% Storage Temperature -4 ~ 140°F (-20 ~ 60°C) Environment condition Storage Humidity ■ 0 ~ 85% The specifications shown above may be changed without prior notice for quality improvement. APPENDIX 125
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 26 Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:a08bed2a-0311-4791-8eb7-415747fa675b Producer : Acrobat Distiller 6.0 (Windows) Create Date : 2006:02:02 18:54:46+09:00 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2006:02:04 10:56:27+09:00 Metadata Date : 2006:02:04 10:56:27+09:00 Document ID : uuid:912c7631-b216-4b2a-b1a4-fdb90bd7a64c Format : application/pdf Creator : choi Title : Microsoft Word - User_s Manual_H_ok.doc Author : choiEXIF Metadata provided by EXIF.tools