LG Electronics USA 37LDBT LCD TV/Monitor User Manual MFL34797004 Edit1

Download:
Mirror Download [FCC.gov]
Document ID	748103
Application ID	HRN8j+e3wcD66w6mYAl9lg==
Document Description	Users Manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	223.01kB (2787656 bits)
Date Submitted	2007-01-17 00:00:00
Date Available	2007-01-17 00:00:00
Creation Date	2007-01-11 20:15:10
Producing Software	Acrobat Distiller 4.0.5 for Macintosh
Document Lastmod	2007-01-11 20:15:25
Document Title	MFL34797004-Edit1
Document Creator	3.3: LaserWriter 8 8.7.1
Document Author:	sun

LCD TV PLASMA TV
LCD TV MODELS
32LC7D
37LC7D
42LC7D
As an ENERGY STAR
Partner LGE U. S. A.,Inc.
has determined that this
product meets the ENERGY
STAR guidelines for
energy efficiency.
PLASMA TV MODELS
42PC5D
50PC5D
P/NO : MFL34797004 (0612-REV00)
WARNING / CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
FCC NOTICE
Class B digital device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not
occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
WARNING / CAUTION
To prevent fire or shock hazards, do not expose
this product to rain or moisture.
Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
CAUTION
Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product
SAFETY INSTRUCTION
IMPORTANT SAFETY INSTRUCTIONS
WARNING / CAUTION
Important safety instructions shall be provided with each apparatus. This information shall be given in a separate
booklet or sheet, or be located before any operating instructions in an instruction for installation for use and
supplied with the apparatus.
This information shall be given in a language acceptable to the country where the apparatus is intended to
be used.
The important safety instructions shall be entitled “Important Safety Instructions”. The following safety
instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety
information may be included by adding statements after the end of the following safety instruction list. At
the manufacturer’s option, a Opicture or drawing that illustrates the intent of a specific safety instruction may
wn
Ow er Mato that safety instruction :
be placed immediately adjacent
nu
ne
rM
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Ow
ner
Ow
ner
Ma
Ma
nu
anu l
al
nu
al
al
Ow
ner
Ma
nu
al
Do not use this apparatus near water
Clean only with dry cloth.
Ow
ner
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other.
A grounding type plug has two blades and a
third grounding prong, The wide blade or the
third prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
Ow
ner
Ma
nu
al
Ow
ner
Ma
Ma
nu
al
nu
al
Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
Ow
ner
Ma
nu
al
Ow
ner
nu
al
Ow
ner
Ma
nu
al
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Ma
Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers)that produce heat.
Only use attachments/accessories specified by
the manufacturer.
Ow
ner
anu
al
8
with an exact replacement part by an authorized servicer. Protect the power cord from
physical or mechanical abuse, such as being
twisted, kinked, pinched, closed in a door, or
walked upon. Pay particular attention to plugs,
wall outlets, and the point where the cord exits
the appliance.
Ow
ner
ner
ner
13
14
11
CAUTION concerning the Power Cord :
Most appliances recommend they be placed
upon a dedicated circuit; that is, a single outlet
circuit which powers only that appliance and
has no additional outlets or branch circuits.
Check the specification page of this owner's
manual to be certain.
Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets, extension
cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of
these conditions could result in electric shock
or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use
of the appliance, and have the cord replaced
Ma
Ma
nu
al
nu
al
Ow
Unplug this apparatus during lightning storms
or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as powersupply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has exposed to rain
or moisture, does not operate normally, or has
been dropped.
nu
al
Ow
ner
Ow
12
10
Ma
Ma
nu
al
Outdoor Use Marking :
WARNING - To Reduce The Risk Of Fire Or
Electric Shock, Do Not Expose This Appliance
To Rain Or Moisture
WARNING / CAUTION
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Wet Location Marking : Apparatus shall not be
exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall
be placed on or over apparatus.
GROUNDING
Ensure that you connect the earth ground wire
to prevent possible electric shock. If grounding methods are not possible, have a qualified
electrician install a separate circuit breaker.
Do not try to ground the unit by connecting it
to telephone wires, lightening rods, or gas pipes.
Power
Supply
Short-circuit
Breaker
15
DISCONNECTING DEVICE FROM MAINS
Mains plug is the disconnecting device. The
plug must remain readily operable.
CONTENTS
WARNING / CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . 2-3
CONTENTS
PREPARATION
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Front & Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front & Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . 8
Attaching the TV to a Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Stand Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Back Cover for Wire Arrangement . . . . . . . . . . . . . . . . . . . . . 12
Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 14
EXTERNAL EQUIPMENT SETUP
HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-26
AV Out Setup & Digital Audio Output . . . . . . . . . . . . . 27
WATCHING TV / CHANNEL CONTROL
Remote Control Key Functions . . . . . . . . . . . . . . . . . . . 28-29
Turning the TV On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Channel Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
- Auto Scan (EZ Scan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
- Add / Delete Channel (Manual Scan) . . . . . . . . . 33
- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
DTV Signal Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Input Source Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
SimpLink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
PICTURE CONTROL
Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 40
Preset Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
- EZ Picture Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
- Color Tone Preset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Manual Picture Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
- EZ Picture - User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
- Color Tone - User Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
XD - Picture Improvement Technology . . . . . . . . . . . . . 44
Advanced - Cinema 3:2 PulldownMode . . . . . . . . . . . . 45
Advanced - Black (Darkness) Level . . . . . . . . . . . . . . . . . . . 45
Picture Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Low - Power Picture Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Image Sticking Minimization (ISM) Method . . . . . . . 47
SOUND & LANGUAGE CONTROL
Preset Sound Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Sound Setting Adjustment - User Mode . . . . . . . . . . . 49
Stereo/SAP Broadcasts Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 50
TV Speakers On/Off Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
On-Screen Menus Language Selection . . . . . . . . . . . . . . 51
Caption/Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Caption Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
TIME SETTING
Clock Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
- Auto Color Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
- Manual Color Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Auto On/Off Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Auto Shut-off Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
PARENTAL CONTROL / RATINGS
Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Channel Blocking & External Input Blocking . . . . . . 61
External Input Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Movie & TV Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
APPENDIX
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Programming the Remote Control . . . . . . . . . . . . . . . . . . . 70
IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
External Control Through RS-232C . . . . . . . . . . . . . . . . .110
PREPARATION
ACCESSORIES
INPUT
TV INPUT
POWER
DVD
MODE
CABLE
TV
AUDIO
HT BRIG
MENU
VCR
STB
BRIG
HT +
ENTER
Manuel de l’Utilisateur
EXIT
TIMER
VOL
1.5V 1.5V
Owner’s Manual
Batteries
RATIO
MUTE
FAV
SIMPL
INK
CH
BACK
Remote Control
WARNING / CAUTION
Ensure that the following accessories are included with your product. If an accessory is missing, please contact the dealer where you purchased the product.
User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standard
compliance for the product.
Power Cord
Option Extras
75ohm Round Cable
D-sub 15 pin Cable
For Plasma TV models
2-eye-bolts
2-Wall brackets
For LCD TV models
26”, 32” only
2- TV Bracket Bolts
2- TV Brackets,
2- Wall Brackets
Cable Management
Twister Holder
Arrange the wires with
the twister holder.
4-Bolts for stand assembly
(Refer to p.15)
PREPARTION
FRONT PANEL INFORMATION
■
Here shown may be somewhat different from your TV.
Front Panel Controls
PREPARATION
Plasma TV Model
Remote Control Sensor
Power Standby Indicator
Illuminates red in standby mode.
When the TV is turned on, the indicator
blinks green and then illuminates green
before the picture is displayed.
INPUT
MENU
VOL
ENTER
INPUT
POWER
Button
INPUT
Button
CH
MENU
MENU
Button
ENTER
ENTER
Button
VOL
VOLUME
(F,G)Buttons
CH
CHANNEL
(E,D)Buttons
PREPARATION
LCD TV Model
CH
CHANNEL Buttons
VOL
VOLUME Buttons
ENTER
ENTER Button
MENU
MENU Button
INPUT
INPUT Button
ON/OFF Button
Remote Control Sensor
Power Standby Indicator
Illuminates red in standby mode.
When the TV is turned on, the indicator blinks green and
then illuminates green before the picture is displayed.
PREPARTION
BACK PANEL INFORMATION
Back Connection Panel
Plasma TV Model
S-VIDEO Input
Provides better picture quality than the
video input.
AV IN 2
S-VIDEO
PREPARATION
VIDEO L/MONO AUDIO R
AUDIO Input
Connections are available for listening to
stereo sound from an external device.
11
VIDEO Input
Connects the video signal from a video
device.
10
SERVICE
ANTENNA/
CABLE IN
HDMI/DVI IN
REMOTE
AUDIO IN
(RGB/DVI) CONTROL IN
OPTICAL
RS-232C IN
(CONTROL & SERVICE)
DIGITAL AUDIO
OUT
COMPONENT IN
Connect a component video/audio device to these
jacks.
AV OUT
Connect a second TV or monitor.
AV (Audio/Video) IN 1
Connect audio/video output from an external
device to these jacks.
S-VIDEO
Connect S-Video out from an S-VIDEO device.
ANTENNA/CABLE IN
Connect over-the air signals to this jack.
Connect cable signals to this jack.
DIGITAL AUDIO OUT
Connect digital audio from various types of equipment.
Note: In standby mode, these ports do not work.
(MONO)
S-VIDEO
VIDEO
AUDIO
COMPONENT IN AV OUT AV IN 1
AUDIO
VIDEO
RGB IN
(PC)
HDMI/DVI IN
Connect a HDMI signal to 1 or 2.
RGB IN (PC)
Connect the monitor output from a PC to the
appropriate input port.
AUDIO IN (RGB/DVI)
Connect the monitor output from a PC to the
appropriate input port.
Remote Control Port
Connect your wired remote control.
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
10
SERVICE
11
Power Cord Socket
For operation with AC power.
Caution: Never attempt to operate the TV on DC
power.
R
LCD TV Model
VIDEO L/MONO AUDIO R
AUDIO Input
Connections are available for listening to
stereo sound from an external device.
VIDEO Input
Connects the video signal from a video
device.
11
AV IN 2
PREPARATION
S-VIDEO Input
Provides better picture quality than the
video input.
S-VIDEO
10
SERVICE
HDMI IN
ANTENNA/
CABLE IN
REMOTE
AUDIO IN
(RGB/DVI) CONTROL IN
OPTICAL
HDMI/DVI IN
RS-232C IN
(CONTROL & SERVICE)
DIGITAL
AUDIO
OUT
COMPONENT IN
Connect a component video/audio device to these
jacks.
AV OUT
Connect a second TV or monitor.
AV (Audio/Video) IN 1
Connect audio/video output from an external
device to these jacks.
S-VIDEO
Connect S-Video out from an S-VIDEO device.
ANTENNA/CABLE IN
Connect over-the air signals to this jack.
Connect cable signals to this jack.
DIGITAL AUDIO OUT
Connect digital audio from various types of equipment.
Note: In standby mode, these ports do not work.
(MONO)
S-VIDEO
VIDEO
AUDIO
COMPONENT IN AV OUT AV IN 1
AUDIO
VIDEO
RGB IN
(PC)
HDMI/DVI IN
Connect a HDMI signal to 1 or 2.
RGB IN (PC)
Connect the monitor output from a PC to the
appropriate input port.
AUDIO IN (RGB/DVI)
Connect the monitor output from a PC to the
appropriate input port.
Remote Control Port
Connect your wired remote control.
RS-232C IN (CONTROL & SERVICE) PORT
Connect to the RS-232C port on a PC.
10
SERVICE
11
Power Cord Socket
For operation with AC power.
Caution: Never attempt to operate the TV on DC
power.
PREPARTION
ATTACHING THE TV TO A WALL
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,
potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.
PREPARATION
Plasma TV Model
■
LCD TV Model
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) on
the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
■
10
Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it
becomes horizontal between the wall and the product.
STAND INSTALLATION (Only 32 inch LCD TV models)
Carefully place the product screen side down on
a cushioned surface that will protect product and
screen from damage.
Assemble the product stand with the product as
shown.
Install the 4 bolts securely, in the back of the
product in the holes provided.
PREPARATION
DESKTOP PEDESTAL INSTALLATION
For proper ventilation, allow a clearance of 4inches on each side from the wall.
Plasma TV
LCD TV
4 inches
4 inches
4 inches
4 inches
4 inches
4 inches
4 inches
4 inches
CAUTION
Ensure adequate ventilation by following the clearance recommendations.
11
PREPARTION
BACK COVER FOR WIRE ARRANGEMENT
Plasma TV
Hold the CABLE MANAGEMENT with both hands and pull it backward as shown.
PREPARATION
CABLE MANAGEMENT
12
Connect the cables as necessary.
To connect an additional equipment, see the External equipment Connections section.
Install the CABLE MANAGEMENT as shown.
LCD TV
Connect the cables as necessary.
To connect an additional equipment, see the External
equipment Connections section.
Install the CABLE MANAGEMENT as shown.
PREPARATION
CABLE MANAGEMENT
Bundle the cables using the supplied twister holder.
! NOTE
Do not hold the CABLE MANAGEMENT when moving
the product.
- If the product is dropped, you may be injured or the
product may be broken.
TWISTER HOLDER
How to remove the CABLE MANAGEMENT
Hold the CABLE MANAGEMENT with both hands and
pull it backward.
13
PREPARTION
■
To prevent the equipment damage, never plug in any power cords until
you have finished connecting all equipment.
1. Antenna (Analog or Digital)
PREPARATION
Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections.
For optimum picture quality, adjust antenna direction if needed.
Wall
Antenna
Socket
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
ANTENNA/
CABLE IN
Outdoor
Antenna
(VHF, UHF)
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Bronze Wire
Be careful not to bend the bronze
wire when connecting the antenna.
2. Cable
ANTENNA/
CABLE IN
Cable TV
Wall Jack
RF Coaxial Wire (75 ohm)
ANTENNA/
CABLE IN
UHF
Antenna
VHF
Signal
Amplifier
To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
■ If the antenna is not installed properly, contact your dealer for assistance.
■
■
! NOTE
14
The TV will let you know when the analog, cable, and digital channel scans are complete.
EXTERNAL EQUIPMENT SETUP
HD RECEIVER SETUP
This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you
do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown
below.
1. How to connect
OPTICAL
(MONO)
DIGITAL AUDIO
OUT
S-VIDEO
VIDEO
AUDIO
AV IN 1
Connect the audio output of the digital set-top box to
the C O M P O N E N T I N A U D I O 1 jacks on the set.
AV OUT
AUDIO
COMPONENT IN
VIDEO
Connect the video outputs (Y, PB, PR) of the digital set
top box to the C O M P O N E N T I N V I D E O 1 jacks on
the set. Match the jack colors
(Y = green, PB = blue, and PR = red).
EXTERNAL EQUIPMENT SETUP
When connecting Component cable
2. How to use
■
■
■
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
Select C o m p o n e n t 1 input source with using the
I N P U T button on the remote control.
PB
PR
If connected to C O M P O N E N T I N 2 input, select
C o m p o n e n t 2 input source.
Signal
Component 1/2
HDMI1/DVI,
HDMI2
480i
Yes
No
480p
Yes
Yes
720p
Yes
Yes
1080i
Yes
Yes
15
EXTERNAL EQUIPMENT SETUP
When connecting HDMI cable
1. How to connect
EXTERNAL EQUIPMENT SETUP
SERVICE
No separated audio connection is necessary.
RGB IN
(PC)
2. How to use
■
■
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
HDMI/DVI IN
RS-232C IN
(CONTROL & SERVICE)
If the digital set-top box supports Auto HDMI function, the
output resolution of the source device will be automatically
set to 1280x720p.
If the digital set-top box player does not support Auto HDMI,
you need to set the output resolution appropriately.
To get the best picture quality, adjust the output resolution of
the source device to 1280x720p.
REMOTE
AUDIO IN
(RGB/DVI) CONTROL IN
ANTENNA/
CABLE IN
Select H D M I 1 / D V I or H D M I 2 input source with using
the I N P U T button on the remote control.
! NOTE
16
Connect the digital set-top box to H D M I / D V I I N 1
or 2 jack on the set.
HDMI-DTV OUTPUT
When connecting HDMI to DVI cable
AUDIO
RGB IN
(PC)
ANTENNA/
CABLE IN
OPTICAL
RS-232C IN
(CONTROL & SERVICE)
DVI-DTV OUTPUT
DIGITAL AUDIO
OUT
(MONO)
S-VIDEO
VIDEO
AUDIO
AV IN 1
EXTERNAL EQUIPMENT SETUP
REMOTE
AUDIO IN
(RGB/DVI) CONTROL IN
AV OUT
HDMI/DVI IN
COMPONENT IN
VIDEO
SERVICE
1. How to connect
Connect the DVI output of the digital set-top box to the H D M I / D V I I N 1 or 2 jack on the set.
Connect the audio output of the digital set-top box to the A U D I O I N ( R G B / D V I) jack on the set.
2. How to use
■
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
■
Select H D M I 1 / D V I or H D M I 2 input source with using the I N P U T button on the remote control.
17
EXTERNAL EQUIPMENT SETUP
DVD SETUP
When connecting Component cable
1. How to connect
VIDEO
AUDIO
Connect the audio outputs of the DVD to the
C O M P O N E N T I N A U D I O 1 jacks on the set.
AV OUT
OPTICAL
2. How to use
■
■
■
■
(MONO)
DIGITAL AUDIO
OUT
S-VIDEO
VIDEO
AUDIO
Turn on the DVD player, insert a DVD.
Select C o m p o n e n t 1 input source with using the I N P U T
button on the remote control.
If connected to C O M P O N E N T I N 2 input, select
C o m p o n e n t 2 input source.
PB
PR
Refer to the DVD player's manual for operating instructions.
Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV
Video output ports
on DVD player
18
PB
PR
PB
PR
B-Y
R-Y
Cb
Cr
Pb
Pr
AV IN 1
EXTERNAL EQUIPMENT SETUP
Connect the video outputs (Y, PB, PR) of the DVD to
the C O M P O N E N T I N V I D E O 1 jacks on the set.
Match the jack colors
(Y = green, PB = blue, and PR = red).
COMPONENT IN
When connecting with an S-Video cable
AUDIO
1. How to connect
Connect the S-VIDEO output of the DVD to the
S - V I D E O input on the set.
Connect the audio outputs of the DVD to the A U D I O
input jacks on the set.
VIDEO
AUDIO
■
Select A V 1 input source with using the I N P U T button on
the remote control.
If connected to A V I N 2, select A V 2 input source.
■
Refer to the DVD player's manual for operating instructions.
■
OPTICAL
DIGITAL AUDIO
OUT
(MONO)
S-VIDEO
VIDEO
AUDIO
UDIO
AV IN 1
Turn on the DVD player, insert a DVD.
When connecting HDMI cable
EXTERNAL EQUIPMENT SETUP
AV OUT
2. How to use
■
COMPONENT IN
S-VIDEO
1. How to connect
Connect the HDMI output of the DVD to the
H D M I / D V I I N 1 or 2 jack on the set.
SERVICE
RGB IN
(PC)
No separated audio connection is necessary.
HDMI/DVI IN
REMOTE
AUDIO IN
(RGB/DVI) CONTROL IN
2. How to use
■
■
NTENNA/
CABLE IN
Select H D M I 1 / D V I or H D M I 2 input source with using
the I N P U T button on the remote control.
RS-232C IN
(CONTROL & SERVICE)
Refer to the DVD player's manual for operating instructions.
! NOTE
If the DVD supports Auto HDMI function, the DVD output
resolution will be automatically set to 1280x720p.
If the DVD does not support Auto HDMI, you need to set
the output resolution appropriately.
To get the best picture quality, adjust the output resolution
of the DVD to 1280x720p.
HDMI-DVD OUTPUT
19

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
Linearized                      : No
Page Count                      : 20
PDF Version                     : 1.6
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:f7006746-b6e2-41b4-8fb8-e9a4ddd37dd6
Modify Date                     : 2007:01:11 20:15:25+09:00
Create Date                     : 2007:01:11 20:15:10+09:00
Metadata Date                   : 2007:01:11 20:15:25+09:00
Document ID                     : uuid:e10bc8d2-17c2-4290-979c-a5928ac75b7a
Format                          : application/pdf
Title                           : MFL34797004-Edit1
Creator                         : 3.3: LaserWriter 8 8.7.1
Author                          : sun
Producer                        : Acrobat Distiller 4.0.5  for Macintosh

EXIF Metadata provided by EXIF.tools