LG Electronics USA 42LP620HUH LED TV MONITOR User Manual MFL67694902 EN indd

LG Electronics USA LED TV MONITOR MFL67694902 EN indd

Contents

User Manual 2

ENGLISH13ASSEMBLING AND PREPARINGSetting up the TVYou can mount your TV to a wall or attach the stand if you wish to place the TV on an entertainment centeror other furniture.Attaching the standIf you are not mounting the TV to a wall, use the following instructions to attach the stand. When attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. Make sure that the screws are fastened tightly. (If they are not fastened securely enough, the TV may tilt forward after being installed.) Do not tighten the screws with too much force; otherwise they may be damaged and come loose later. CAUTION Remove the stand before installing the TV on a wall mount by performing the stand attachment in reverse. NOTE1 2FrontStand BodyStand BaseM4 x 204 EA3orTighten the two of these four screws and the two Torx plus star head screws (provided as parts of the TV) to secure the TV. Tighten the two Torx plus star head screws with a star head driver bit (not provided as parts of the TV).2 EAὤ㨴㥄 wyv{lj{pvuGjv}ly2 EAM4 x 164 EA
ENGLISH14 ASSEMBLING AND PREPARINGMounting on a table1 Lift and tilt the TV into its upright position on a table.- Leave a 10 cm (4 inch) (minimum) space from the wall for proper ventilation.10 cm10 cm10 cm10 cm(4 inches)2 Connect the power cord to a wall outlet. Do not place the TV near or on sources of heat, as this may result in fire or other damage. CAUTIONSecuring the TV to a tableFix the TV to a table to prevent from tilting forward, damage, and potential injury. Mount the TV on a table, and then insert and tighten the supplied screw on the rear of the stand. To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the TV may cause injury. WARNING Make sure that children do not climb on or hang on the TV. CAUTIONUsing the Kensington security system (optional)The Kensington security system connector is located at the rear of the TV. For more information of installation and using, refer to the manual provided with the Kensington security system or visit http://www.kensington.com.Connect the Kensington security system cable between the TV and a table. The Kensington security system is optional. You can obtain additional accessories from your local dealer. NOTE
ENGLISH15ASSEMBLING AND PREPARINGAttaching the TV to a deskThe TV should be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product.TYPE 14-Screws(Not provided as parts of the product)DeskStand NOTE Screw: M5 x L (*L: Table depth + 8~10 mm) ex) Table depth: 15mm, Screw: M5 x 25TYPE 22-Screws, 2-Washers, 2-Nuts, 4-Rubbers(provided as parts of the product)DeskStandAdjusting the angle of the TV to suit view(Depending on model)The swivel angle is adjustable. If no adjustment screw (M6 X 10) is used, the swivel angle is ±90°.Installing the adjustment screw in the B position will restrict the swivel angle to ±45°, and installing the adjustment screw in the A position will restrict the swivel angle to ±20°.Installing an adjustment screw in the A and B positions will restrict the swivel angle to ±20°.(Basically, only one screw (M6 X 10) is provided for fixing swivel.)90˚90˚BA When adjusting the angle of the TV, watch out for your fingers. - Personal injury may occur if hands or fingers are pinched. If the product is tilted too much, it may fall, causing damage or injury. CAUTION
ENGLISH16 ASSEMBLING AND PREPARINGMounting on a wallAn optional wall mount can be used with your LG Television. Consult with your local dealer for a wall mount that supports the VESA standard used by your TV model. Carefully attach the wall mount bracket at the rear of the TV. Install the wall mount bracket on a solid wall perpendicular to the floor. If you are attaching the TV to other building materials, please contact qualified personnel to install the wall mount. Detailed instructions will be included with the wall mount. We recommend that you use an LG brand wall mount.10 cm10 cm10 cm10 cm(4 inches)Make sure to use screws and wall mounts that meet the VESA standard. Standard dimensions for the wall mount kits are described in the following table.Model 32LP645H32LP620H32LP621H37LP645H37LP620H37LP621H39LP645H39LP620H42LP645H42LP620H42LP621HVESA (A x B) AB200 x 100 200 x 200Standard screw M4 M6Number of screws 4 4Wall mount bracket (optional)LSW130B LSW230B Model 47LP645H55LP645H60LP645HVESA (A x B) AB400 x 400Standard screw M6Number of screws 4Wall mount bracket (optional)LSW430B Securing the TV to a wall (optional)(Depending on model)1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. - If there are bolts inserted at the eye-bolts position, remove the bolts first.2 Mount the wall brackets with the bolts to the wall.Match the location of the wall bracket and the eye-bolts on the rear of the TV.3 Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface. Make sure that children do not climb on or hang on the TV. CAUTION Use a platform or cabinet that is strong and large enough to support the TV securely. Brackets, bolts and ropes are optional. You can obtain additional accessories from your local dealer. NOTE
ENGLISH17ASSEMBLING AND PREPARINGTidying cables1 Install the power cord holder and power cord. It will help prevent the power cable from being removed by accident.2 Gather and bind the cables with the cable holder.For 32/37/39/42LP645H, 32/37/39/42LP620H, 32/42LP621HPower Cord Holder and ScrewCable HolderFor 47/55/60LP645HPower Cord Holder and ScrewCable Holder Do not move the TV by holding the cable holder and power cord holder, as the cable holders may break, and injuries and damage to the TV may occur. CAUTION Disconnect the power before moving or installing the TV. Otherwise electric shock may occur. If you install the TV on a ceiling or slanted wall, it may fall and result in severe injury. Use an authorized LG wall mount and contact the local dealer or qualified personnel. Do not over tighten the screws as this may cause damage to the TV and void your warranty. Use the screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty. CAUTION The wall mount bracket is optional. You can obtain additional accessories from your local dealer. Use the screws that are listed in the VESA standard screw specifications. The wall mount kit includes an installation manual and necessary parts. The length of screws may differ depending on the wall mount. Make sure to use the proper length. For more information, refer to the manual supplied with the wall mount. NOTEExternal speaker outConnect the external speaker.GAME CONTROL21/ DVI INRS-232C IN(CONTROL & SERVICE)RGB IN (PC)SPEAKER OUTLINE OUTANTENNA/CABLE INOPTICALAUDIO OUTAV INVIDEOL/MONO-AUDIO-RLRAUDIO IN (RGB DVI)RESETUPDATERJPPTC SERVICE(SERVICE ONLY) TV-LINKCFG/ M.P.IGAME CONTROLGAME CONTROLGAME CONTROLRGNDLGND Make sure that the external speaker should be connected with TV under power-off state. Use external speaker with SE type (3 pin). NOTE
ENGLISH18 REMOTE CONTROLREMOTE CONTROLBelow is a description of the remote control. Your remote control may look slightly different.To install batteries, open the battery cover, insert batteries (1.5 V AAA) matching the and ends to the label inside the compartment, and close the battery cover. To remove the batteries, perform the installation actions in reverse.This remote uses infrared light. When in use, it should be pointed in the direction of the TV’s remote sensor.CH1 2 34 5 67 809PAGEQ.MENUINPUTCHAR/NUMFLASHBKEXITOKGUIDEPORTALTV DVDMARKCCTIMERMUTEINFOPIP PIPCH+ PIPCH-SWAPPIP INPUTSAPMENUSETTINGSabc defghi jkl mnopqrs tuv wxyz.,;@DELETEENTERVOL (POWER)Turns the TV on or off.Q. MENUNot functionalTVSelects the remote’s operating mode: TV.DVDSelects the remote’s operating mode: DVD. INPUTRotates through inputs. Also switches the TV on from standby.MARKNot functionalNumber buttonEnters channel numbers or other numbers required. Also supports characters.— (DASH) Selects a program number for multiple program channels such as 2-1, 2-2, etc.FLASHBKTunes to the last channel or input viewed. VOL Adjusts the volume level.CHAR/NUMSwitches between Letter and Number input modes.CCSelects a closed caption.TIMERTurns the TV off in a set amount of time.DELETEDeletes letters and numbers.MUTE Mutes all sounds.^ CH vScrolls through the saved channels. PAGE Moves to the previous or next screen. Do not mix old and new batteries, as this may damage the remote control. CAUTION
ENGLISH19REMOTE CONTROLCH1 2 34 5 67 809PAGEQ.MENUINPUTCHAR/NUMFLASHBKEXITOKGUIDEPORTALTV DVDMARKCCTIMERMUTEINFOPIP PIPCH+ PIPCH-SWAPPIP INPUTSAPMENUSETTINGSabc defghi jkl mnopqrs tuv wxyz.,;@DELETEENTERVOLColor buttons ( : Red, : Green, : Yellow, : Blue )These access special functions in some menus.VCR/DVD/USB control buttons ( , , , , )Controls video cassette recorders or DVD players or USB. Accesses the AV devices connected to the TV; Opens the SIMPLINK menu.PIPNot functionalPIP CH +/-Not functionalSWAPNot functionalPIP INPUTNot functionalSAPAnalog mode: Selects MTS sound (Mono, Stereo or SAP)DTV mode: Changes the audio language.PORTALDisplays and removes the interactive menu.INFO Views the information of the current program and screen.GUIDEDisplays and removes the electronic program guide.Navigation buttons (up/down/left/right) Scrolls through menus or options.OK/ENTER ꔉSelects menus or options and confirms your input.ꕣ (BACK)Returns to the previous level.MENU/SETTINGSAccesses the main menu.EXIT ꕯClears all on-screen displays and returns to TV viewing.
ENGLISH20 SPECIFICATIONSSPECIFICATIONSProduct specifications may be changed without prior notice due to upgrade of product functions.Power requirement AC 100 - 240 V ~ 50 / 60 HzTelevision System NTSC-M, ATSC, 64 & 256 QAMProgram Coverage VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135External Antenna Impedance 75 ΩEnvironment conditionOperating Temperature 0 - 40 °COperating Humidity Less than 80 %Storage Temperature -20 - 60 °CStorage Humidity Less than 85 %MODELS 32LP645H (32LP645H-UH)32LP620H (32LP620H-UH)32LP621H (32LP621H-UA)Dimensions (W x H x D)With stand 738 x 497 x 207 (mm)29.0 x 19.6 x 8.1 (inch)Without stand738 x 449 x 79 (mm)29.0 x 17.7 x 3.1 (inch)Weight With stand 7.0 kg (15.4 lbs)Without stand 6.4 kg (14.1 lbs)Current Value / Power consumption 1.3 A / 80 WMODELS 37LP645H (37LP645H-UH)37LP620H (37LP620H-UH)Dimensions (W x H x D)With stand 849 x 558 x 226 (mm)33.4 x 22.0 x 8.9 (inch)Without stand 849 x 500 x 79 (mm)33.4 x 19.7 x 3.1 (inch)Weight With stand 9.1 kg (20.1 lbs)Without stand 8 kg (17.6 lbs)Current Value / Power consumption 1.5 A / 150 WMODELS 39LP645H (39LP645H-UH)39LP620H (39LP620H-UH)Dimensions (W x H x D)With stand 894 x 583 x 283 (mm)35.2 x 23.0 x 11.1 (inch)Without stand 894 x 537 x 79 (mm)35.2 x 21.1 x 3.1 (inch)Weight With stand 9.7 kg (21.4 lbs)Without stand 8.6 kg (19.0 lbs)Current Value / Power consumption 1.5 A / 150 W
ENGLISH21SPECIFICATIONSMODELS 42LP645H (42LP645H-UH)42LP620H (42LP620H-UH)42LP621H (42LP621H-UA)Dimensions (W x H x D)With stand 968 x 625 x 283 (mm)38.1 x 24.6 x 11.1 (inch)Without stand968 x 579 x 79 (mm)38.1 x 22.8 x 3.1 (inch)Weight With stand 13.3 kg (29.3 lbs)Without stand 9.6 kg (21.2 lbs)Current Value / Power consumption 1.6 A / 160 WMODELS 47LP645H (47LP645H-UH)Dimensions (W x H x D)With stand 1,080 x 688 x 282.4 (mm)42.5 x 27.1 x 11.1 (inch)Without stand 1,080 x 642 x 80.5 (mm)42.5 x 25.3 x 3.2 (inch)Weight With stand 16.7 kg (36.8 lbs)Without stand 13.4 kg (29.5 lbs)Current Value / Power consumption 1.3 A / 130 WMODELS 55LP645H (55LP645H-UH)Dimensions (W x H x D)With standWithout standWeight With standWithout standCurrent Value / Power consumptionMODELS 60LP645H (60LP645H-UA)Dimensions (W x H x D)With standWithout standWeight With standWithout standCurrent Value / Power consumption
ENGLISH22 SPECIFICATIONSHDMI (DTV) supported modeResolution Horizontal Frequency (kHz)Vertical Frequency (Hz)720 x 480p 31.47 59.9431.50 60.001280 x 720p 44.96 59.9445.00 60.001920 x 1080i 33.72 59.9433.75 60.001920 x 1080p26.97 23.97627.00 24.0033.71 29.9733.75 30.0067.432 59.9467.50 60.00RGB (PC), HDMI (PC) supported modeResolution HorizontalFrequency (KHz)VerticalFrequency (Hz)720x400 31.46 70.08640x480 31.46 59.94800x600 37.87 60.311024x768 48.36 60.001360x768 47.71 60.011280x1024 63.98 60.021920x1080 67.50 60.00Except 32/37LP645H, 32/37LP620H, 32LP621H
ENGLISH23TROUBLESHOOTINGTROUBLESHOOTINGGeneralProblem SolutionCannot control the TV with the remote control. Check the remote control sensor on the product and try again. Check if there is any obstacle between the product and the remote control. Check if the batteries are still working and properly installed ( to , to ).No image display and no sound is produced. Check if the product is turned on. Check if the power cord is connected to a wall outlet. Check if there is a problem in the wall outlet by connecting other products.Image appears slowly when the TV turns on. The image is muted during the product startup process. This is normal. If the image does not appear in a few minutes, unplug the TV for 30 seconds and try again. If the image still does not appear, contact the authorized service center in your local area.Cannot connect external devices.  Refer to the “Connection Overview” and connect an external device.The TV turns off suddenly.  Check the power control settings. The power supply may be interrupted. Check if the Auto sleep feature is activated in the Time settings. Refer to the “Sleep Timer”.AudioProblem SolutionNo sound is produced while images are displaying. Press VOL + or - button. Check if the sound is muted by pressing MUTE. Scroll to other channels. There may a problem with the broadcast. Check if the TV Speaker feature is activated in the menu option.No output from one of the speakers  Adjust Balance in the menu option.Unusual sound from inside the TV is produced. A change in ambient humidity or temperature may result in an unusual noise when the product turns on or off. There is no problem with your product.VideoProblem SolutionAn image displays in black and white or the color quality is poor. Adjust the color setting in the menu option. Keep a sufficient distance between this product and other electronic products. Scroll to other channels. There may a problem with the broadcast.Horizontal or vertical bars appears or images blur Check if there are local interferences such as an electrical appliance or power tool.Lines or streaks appear on images  Check the antenna or aim the antenna to the proper direction.Afterimages (ghosts) appear when the product turns off Pixels may have been damaged from a fixed image displayed for a long time (image burn). Use a screen saver to prevent the pixel damage on the screen.The power is on but the screen appears extremely dark. Adjust the brightness and contrast in the menu option.“No Signal” appears on the screen.  Check if the signal cable is connected between the TV and products properly. Check the selected input source by pressing INPUT.Black spots appear on the screen.  Several pixels in red, green, white, or black may appear on the screen that can attribute to the characteristics of the panel.  This is normal.The display offset is wrong.  Adjust the position setting in the Picture menu. Check if the video card resolution and frequency are supported by the product. If the frequency is out of range, set to the recommended resolution using the display settings on the external device.Thin lines appear in the background of the screen. Check the video cable connections.The reception on some channels is poor Scroll to other channels. There may a problem with the broadcast. The station signal may be weak. Aim the antenna to the proper direction. Check if there is local interferences such as an electrical appliance or power tool.
The model and serial number of the TV is located on the back and one side of the TV. Record it below should you ever need service.MODELSERIALPro:Centric is a trademark of LG Electronics U.S.A., Inc. Pro:Idiom isa registered trademark of Zenith Electronics LLC. b-LAN is a trademark of LodgeNet Interactive Corporation. All other trademarks or registered trademarks are the property of their respective owners.LG Customer Information CenterFor inquires or comments, visit www.lg.com or call:1-888-865-30261-888-542-2623USA, Commercial UserCANADAThis product qualifies for ENERGY STAR in the “factory default (Home Use)” setting.Changing the factory default settings or enabling other features may increase power consumption that could exceed the limits necessary to quality for ENERGY STAR.

Navigation menu