LG Electronics USA 42PC5DUC Plasma Monitor User Manual MFL34797004 Edit1

LG Electronics USA Plasma Monitor MFL34797004 Edit1

Contents

Users Manual 2

PREPARATION14PREPARTION■To prevent the equipment damage, never plug in any power cords untilyou have finished connecting all equipment.1. Antenna (Analog or Digital)Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections. For optimum picture quality, adjust antenna direction if needed.2. CableR( )WallAntennaSocketOutdoorAntenna(VHF, UHF)Cable TVWall JackMulti-family Dwellings/Apartments(Connect to wall antenna socket)RF Coaxial Wire (75 ohm)RF Coaxial Wire (75 ohm)Single-family Dwellings /Houses(Connect to wall jack for outdoor antenna) Be careful not to bend the bronzewire when connecting the antenna.Bronze WireR( )ANTENNA/CABLE INR( )ANTENNA/CABLE INR( )ANTENNA/CABLE INGGThe TV will let you know when the analog, cable, and digital channel scans are complete.NOTE!■To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly. ■If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.■If the antenna is not installed properly, contact your dealer for assistance.AntennaUHFSignalAmplifierVHF
EXTERNAL EQUIPMENT SETUP15HD RECEIVER SETUPEXTERNAL EQUIPMENT SETUPThis TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if youdo receive digital signals from a digital set-top box or other digital external device, refer to the figure as shownbelow.DIGITAL AUDIO OUTOPTICALAV OUTAV IN 1VIDEOAUDIOMONO( )S-VIDEOCOMPONENT INVIDEOAUDIOY L RPBPRWhen connecting Component cable1 21. How to connectConnect the video outputs (Y, PB, PR)of the digital set top box to the CCOOMMPPOONNEENNTT IINN VVIIDDEEOO 11jacks onthe set. Match the jack colors (Y = green, PB= blue, and PR= red).Connect the audio output of the digital set-top box to the CCOOMMPPOONNEENNTT IINN AAUUDDIIOO 11jacks on the set.212. How to use■Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)■Select CCoommppoonneenntt 11 input source with using theIINNPPUUTT button on the remote control.■If connected to CCOOMMPPOONNEENNTT IINN22 input, selectCCoommppoonneenntt 22 input source.Signal480i480p720p1080 iComponent 1/2YesYesYesYesHDMI1/DVI, HDMI2NoYesYesYes
EXTERNAL EQUIPMENT SETUP16EXTERNAL EQUIPMENT SETUPWhen connecting HDMI cableConnect the digital set-top box to HHDDMMII//DDVVII IINN 11or 22 jack on the set.No separated audio connection is necessary.1. How to connect2. How to use■Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)■Select HHDDMMII11//DDVVIIor HHDDMMII22 input source with usingthe IINNPPUUTTbutton on the remote control.21HDMI/DVI IN ANTENNA/CABLE INREMOTECONTROL INRS-232C IN(CONTROL & SERVICE)RGB IN(PC)AUDIO IN(RGB/DVI)12SERVICEHDMI-DTV OUTPUT1GGIf the digital set-top box supports Auto HDMI function, theoutput resolution of the source device will be automaticallyset to 1280x720p.GGIf the digital set-top box player does not support Auto HDMI,you need to set the output resolution appropriately.To get the best picture quality, adjust the output resolution ofthe source device to 1280x720p.NOTE!
EXTERNAL EQUIPMENT SETUP17HDMI/DVI IN ANTENNA/CABLE INREMOTECONTROL INRS-232C IN(CONTROL & SERVICE)RGB IN(PC)AUDIO IN(RGB/DVI)DIGITAL AUDIO OUTOPTICAL12SERVICECOMPONENT IN AV OUTAV IN 1VIDEOAUDIOMONO( )S-VIDEOVIDEOAUDIOL RDVI-DTV OUTPUTConnect the DVI output of the digital set-top box to the HHDDMMII//DDVVII IINN 11or 22 jack on the set.Connect the audio output of the digital set-top box to the AAUUDDIIOO IINN ((RRGGBB//DDVVII))jack on the set.1. How to connect■Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)■Select HHDDMMII11//DDVVIIor HHDDMMII22input source with using the IINNPPUUTTbutton on the remote control.2. How to use2112When connecting HDMI to DVI cable
EXTERNAL EQUIPMENT SETUP18DVD SETUPEXTERNAL EQUIPMENT SETUPWhen connecting Component cableDIGITAL AUDIO OUTOPTICALAV OUTAV IN 1VIDEOAUDIOMONO( )S-VIDEOCOMPONENT INVIDEOAUDIOY L RPBPRAUDIO( )Component Input portsTo get better picture quality, connect a DVD player to the component input ports as shown below.Component ports on the TVYPBPRVideo output ports on DVD playerYYYYPBB-YCbPbPRR-YCrPrConnect the video outputs (Y, PB, PR)of the DVD tothe CCOOMMPPOONNEENNTT IINN VVIIDDEEOO11jacks on the set.Match the jack colors (Y = green, PB= blue, and PR= red).Connect the audio outputs of the DVD to the CCOOMMPPOONNEENNTT IINN AAUUDDIIOO11jacks on the set.1. How to connect2. How to use■Turn on the DVD player, insert a DVD.■Select CCoommppoonneenntt 11 input source with using the IINNPPUUTTbutton on the remote control.■If connected to CCOOMMPPOONNEENNTT IINN 22 input, selectCCoommppoonneenntt 22 input source.■Refer to the DVD player's manual for operating instructions.211 2
EXTERNAL EQUIPMENT SETUP19When connecting with an S-Video cableDIGITAL AUDIO OUTOPTICALCOMPONENT IN AV OUTAV IN 1VIDEOS-VIDEOVIDEOAUDIOAUDIOUDIOMONO( )L RS-VIDEOAUDIO12HDMI/DVI IN NTENNA/CABLE INREMOTECONTROL INRS-232C IN(CONTROL & SERVICE)RGB IN(PC)AUDIO IN(RGB/DVI)12SERVICEHDMI-DVD OUTPUTAUDIO( )1Connect the S-VIDEO output of the DVD to theSS--VVIIDDEEOOinput on the set.Connect the audio outputs of the DVD to the AAUUDDIIOOinput jacks on the set.1. How to connect2. How to use■Turn on the DVD player, insert a DVD.■Select AAVV11input source with using the IINNPPUUTTbutton onthe remote control.■If connected to AAVV IINN22, select AAVV22 input source.■Refer to the DVD player's manual for operating instructions.When connecting HDMI cableConnect the HDMI output of the DVD to theHHDDMMII//DDVVII IINN 11or 22jack on the set.No separated audio connection is necessary.1. How to connect2. How to use■Select HHDDMMII11//DDVVIIor HHDDMMII22input source with usingthe IINNPPUUTTbutton on the remote control.■Refer to the DVD player's manual for operating instructions.2121GGIf the DVD supports Auto HDMI function, the DVD outputresolution will be automatically set to 1280x720p.GGIf the DVD does not support Auto HDMI, you need to setthe output resolution appropriately. To get the best picture quality, adjust the output resolutionof the DVD to 1280x720p.NOTE!
EXTERNAL EQUIPMENT SETUP20VCR SETUPEXTERNAL EQUIPMENT SETUPWhen connecting with an antenna■To avoid picture noise (interference), leave an adequate distance between the VCR and TV■Use the ISM feature in the Option menu to avoid having a fixed image remain on the screen for a long periodof time. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible onthe screen. This phenomenon is common to all manufactures and in consequence the manufactures warrantydoes not cover the product bearing this phenomenon.HDMI/DVI IN ANTENNA/CABLE INREMOTECONTROL INRS-232C IN(CONTROL & SERVICE)RGB IN(PC)AUDIO IN(RGB/DVI)DIGITAL AUDIO OUTOPTICAL12VIDEOS-VIDEOL RS-VIDEO VIDEOOUTPUTSWITCHANT INANT OUTVIDEOAUDIO( )AUDIO( )Wall JackAntenna12Connect the RF antenna out socket of the VCR to the AAnntteennnnaasocket on the set.Connect the antenna cable to the RF antenna in socket of the VCR.1. How to connect■Set VCR output switch to 3 or 4 and then tune TV to the same channel number.■Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)2. How to use21
EXTERNAL EQUIPMENT SETUP21GGDo not connect to both Videoand S-Video at the same time. Inthe event that you connect bothVideo and the S-Video cables,only the S-Video will work.CAUTIONWhen connecting with a RCA cableGGThe picture quality is improved: compared to normalcomposite (RCA cable) input.NOTE!NDIGITAL AUDIO OUTOPTICALCOMPONENT IN AV OUTAV IN 1S-VIDEOVIDEOAUDIOVIDEOAUDIOMONO( )L RS-VIDEO VIDEOOUTPUTSWITCHANT INANT OUTAUDIO( )VIDEOAUDIO( )L RS-VIDEO VIDEOOUTPUTSWITCHANT INANT OUTDIGITAL AUDIO OUTOPTICALCOMPONENT IN AV OUTVIDEOAUDIOAV IN 1VIDEOS-VIDEO AUDIOMONO( )Connect the AAUUDDIIOO/VVIIDDEEOOjacks between TV andVCR. Match the jack colors (Video = yellow, Audio Left= white, and Audio Right = red)1. How to connect2. How to use■Insert a video tape into the VCR and press PLAY on theVCR. (Refer to the VCR owner’s manual.)■Select AAVV11input source with using the IINNPPUUTTbutton onthe remote control.■If connected to AAVV IINN22, select AAVV22 input source.When connecting with an S-Video cableConnect the S-VIDEO output of the VCR to theSS--VVIIDDEEOO input on the set.Connect the audio outputs of the VCR to the AAUUDDIIOOinput jacks on the set.1. How to connect2. How to use■Insert a video tape into the VCR and press PLAY on the VCR.(Refer to the VCR owner’s manual.)■Select AAVV11input source with using the IINNPPUUTTbutton onthe remote control.■If connected to AAVV IINN22, select AAVV22 input source.121GGIf you have a mono VCR, con-nect the audio cable from theVCR to the AAUUDDIIOOLL//MMOONNOOjack of the set.NOTE!112
EXTERNAL EQUIPMENT SETUP22OTHER A/V SOURCE SETUPEXTERNAL EQUIPMENT SETUPAV IN 2L/MONORAUDIOVIDEOS-VIDEOL RVIDEOCamcorderVideo Game SetConnect the AAUUDDIIOO/VVIIDDEEOOjacksbetween TV and external equipment.Match the jack colors.(Video = yellow, Audio Left = white, andAudio Right = red)1. How to connect2. How to use■Select AAVV22 input source with using theIINNPPUUTTbutton on the remote control.■If connected to AAVV IINN11input, select AAVV11input source.■Operate the corresponding external equipment.11GGThis TV finds the connected input sources automati-cally for AV1, AV2, Component 1-2, RGB,HDMI1/DVI and HDMI2 sources are connected.NOTE!
EXTERNAL EQUIPMENT SETUP23PC SETUPThis TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. When connecting D-sub 15pin cableGGCheck the image on your TV. There may be noise associ-ated with the resolution, vertical pattern, contrast orbrightness in PC mode. If noise is present, change the PCoutput to another resolution, change the refresh rate toanother rate or adjust the brightness and contrast on theVIDEO menu until the picture is clear. If the refresh rateof the PC graphic card can not be changed, change thePC graphic card or consult the manufacturer of the PCgraphic card.NOTE!RGB OUTPUTAUDIOHDMI/DVI IN REMOTECONTROL INRS-232C IN(CONTROL & SERVICE)RGB IN(PC)AUDIO IN(RGB/DVI)DIGITAL AUDIOOUTOPTICAL12ERVICEConnect the RGB output of the PC to the RRGGBB IINN((PPCC)) jack on the set.Connect the PC audio output to the AAUUDDIIOO IINN((RRGGBB//DDVVII))jack on the set.1. How to connect2. How to use■Turn on the PC and the set.■Select RRGGBB--PPCCinput source in main input option ofSETUP menu. ((GG pp..6677))2112
EXTERNAL EQUIPMENT SETUP24EXTERNAL EQUIPMENT SETUPWhen connecting HDMI to DVI cableANTENNA/CABLE INREMOTECONTROL RS-232C IN(CONTROL & SERVICERGB IN(PC)AUDIO IN(RGB/DVI)SERVICEHDMI/DVI IN 12DVI-PC OUTPUT AUDIO12GGIf the PC has a DVI output and no HDMI output, a sepa-rated audio connection is necessary.GGIf the PC does not support Auto DVI, you need to set theoutput resolution appropriately. To get the best picturequality, adjust the output resolution of PC graphics card'soutput resolution to 1024x768, 60Hz.NOTE!Connect the DVI output of the PC to the HHDDMMII//DDVVIIIINN 11or 22 jack on the set.Connect the PC audio output to the AAUUDDIIOO IINN((RRGGBB//DDVVII))jack on the set.1. How to connect2. How to use■Turn on the PC and the set■Select HHDDMMII11//DDVVIIor HHDDMMII22 input source with usingthe IINNPPUUTTbutton on the remote control.21
EXTERNAL EQUIPMENT SETUP25GGTo get the the best picture quality, adjust the PCgraphics card to 1024x768, 60Hz.GGDepending on the graphics card, DOS mode maynot work if a HDMI to DVI Cable is in use.GGWhen Source Devices are connected withHDMI/DVI Input, the output PC Resolution (VGA,SVGA, XGA, WXGA), Position and Size may not fiton the Screen. Press the ADJUST button to adjustthe screen Position of the TV SET and contact aPC graphics card service center.GGWhen Source Devices connected with HDMI/DVIInput, output TV SET Resolution (480p, 720p,1080i, 1080p) and TV SET Display fit EIA/CEA-861-B Specification to Screen. If not, refer to theManual of HDMI/DVI Source Devices or contactyour service center.GGIf the HDMI/DVI Source Device is not connectedto the Cable or if there is a poor cable connec-tion, "No signal" is displayed in the HDMI/DVIInput. In this case, that Video Resolution is notsupported. If "Invalid Format" is displayed, refer tothe Source Device manual or contact your servicecenter.GGAvoid keeping a fixed image on the screen for along period of time. The fixed image may becomepermanently imprinted on the screen.GGThe synchronization input form for Horizontaland Vertical frequencies is separate.NOTES!RGB-PC, HDMI1/DVI-PC mode Horizontal Vertical Frequency(KHz)Frequency(Hz)31.469 70.0831.469 70.0831.469 59.9437.879 60.3148.363 60.0047.776 59.8747.720 59.79947.130 59.65Resolution 720x4001360x768640x350* RGB-PC mode only: 640x350, 720X400640x480800x6001024x768HDMI1/DVI-DTV, HDMI2-DTV modeHorizontal Vertical Frequency(KHz)Frequency(Hz)31.469 59.9431.500 60.0044.960 59.9445.000 60.0033.720 59.9433.750 60.0027.000 24.0033.750 30.00Resolution 720x4801280x7201920x1080i1920x1080p1280x7681366x768Supported Display Specifications
EXTERNAL EQUIPMENT SETUP26EXTERNAL EQUIPMENT SETUPScreen Setup for PC modeOverviewWhen RGB connect to PC output and select the RGB-PC in Inputsource, this function is used.When HDM/DVI connect to PC output and select HDMI/DVI input,this function is used.After connecting RGB-PC or HDMI/DVI to PC input and checking thescreen quality.When you change the resolution, select the proper resolution in pre-sent input to see the best picture appearance.Adjustment for screen Resolution, Position, Size,and PhasePress the AADDJJUUSSTTbutton and then use DD or EEbutton toselect RReessoolluuttiioonn, PPoossiittiioonn, SSiizzee, or PPhhaassee.Press the EENNTTEERRbutton and then use DD EE FFGG button tomake appropriate adjustments.■The PPhhaasseeadjustment range is --1166 ~++1166.In HDMI/DVI-PC mode, PPhhaassee is not available.■The SSiizzeeadjustment range is --3300 ~++3300.In HDMI/DVI-PC mode, SSiizzeeis not available.Press the EENNTTEERRbutton.Initializing (Reset to original factory values)Press the AADDJJUUSSTTbutton and then use DD or EEbutton toselect RReesseett.Press the EENNTTEERR button and then use FFor GG button toselect YYeess.Press the EENNTTEERRbutton.To initialize the adjusted valuesADJUSTSAPSOUNDPICTURECC123123RReessoolluuttiioonnThis function allows you selectresolution of XGA/WXGA.PPoossiittiioonnThis function is to adjust picture toleft/right and up/down as you prefer.SSiizzeeThis function is to minimize any ver-tical bars or stripes visible on thescreen background. And the hori-zontal screen size will also change. PPhhaasseeThis function allows you toremove any horizontal noise andclear or sharpen the image of char-acters.1231231024 x 7681280 x 7681360 x 7681366 x 768CloseClose
EXTERNAL EQUIPMENT SETUP27AV OUT SETUPThe TV has a special signal output capability which allows you to hook up the second TV or monitor.L R S-VIDEOVIDEOL AUDIO UTICALNT IN AV OUTAV IN 1VIDEOAUDIOMONO( )S-VIDEOConnect the second TV or monitor to the TV’s AAVV OOUUTTjacks. See the Operating Manual of the second TV or monitorfor further details regarding that device’s input settings.1. How to connectGGComponent1-2, RGB-PC, HDMI1/DVI, HDMI2, DTV inputsources cannot be used for AV out.GGWe recommend to use the AV OUT jacks for VCR recording.NOTE!211Send the TV’s audio to external audio equipment via the Digital Audio Output (Optical)port.REMOTECONTROL INRS-232C IN(CONTROL & SERVICE)(PC)AUDIO IN(RGB/DVI)VIDEOS-VIDEODIGITAL AUDIO OUTOPTICALGGWhen connecting with external audio equipments, such as ampli-fiers or speakers, please turn the TV speakers off. (GG pp..8844)NOTE!GGDo not look into the optical output port. Looking at thelaser beam may damage your vision.CAUTIONConnect one end of an optical cable to the TV DigitalAudio (Optical)Output port.Connect the other end of the optical cable to thedigital audio (optical)input on the audio equipment.Set the “TV Speaker option - Off” in the AUDIOmenu. (GGpp..8844). See the external audio equipmentinstruction manual for operation.1. How to connect23112DIGITAL AUDIO OUTPUT
WATCHING TV / CHANNEL CONTROL28REMOTE CONTROL FUNCTIONSWATCHING TV / CHANNEL CONTROL1 2 3 4 5 6 7809 BACKVOL CHMUTEFAVBRIGHT -MENUBRIGHT +ENTEREXITTIMERRATIOSIMPLINKPOWERVCRTVDVDAUDIOCABLESTBMODETV INPUTINPUTMODEMENUBRIGHT -/ +THUMBSTICK(Up/Down/LeftRight/ENTER)EXITTIMERRATIOSIMPLINK VOLUME UP/DOWNMUTEFAVCHANNELUP/DOWN— (DASH)BACKSelect the remote operating mode: TV, DVD, VCR,AUDIO, CABLE or STB. Control video cassette recorders or DVD players.Displays the main menu. Adjust the brightness on screen.It turns to the default settings brightness by changingmode source.Navigate the on-screen menus and adjust the system set-tings to your preference.Clear all on-screen displays and return to TV viewingfrom any menu.Select the amount of time before your TV turns off auto-matically. GGpp..9900Change the aspect ratio. GGpp..9922--9933C? GGpp..9922--9933Increase/decrease the sound level.Switch the sound on or off. GGpp..3388Scroll through the programmed Favorite channels.Select available channels.Used to enter a program number for multiple programchannels such as 2-1, 2-2, etc.Tune to the last channel viewed.VCR/DVD control buttonsNUMBER buttonWhen using the remote control, aim it at the remote control sensor on the TV.Illuminates the remote controlbuttons of selected mode.LIGHT

Navigation menu