LG Electronics USA 42PC5DUC Plasma Monitor User Manual MFL34797004 Edit1

Download:
Mirror Download [FCC.gov]
Document ID	741908
Application ID	LP2exvZWzeJNuuoi5IA28g==
Document Description	Users Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	244.06kB (3050767 bits)
Date Submitted	2006-12-22 00:00:00
Date Available	2006-12-26 00:00:00
Creation Date	2006-12-29 16:19:16
Producing Software	Acrobat Distiller 4.0.5 for Macintosh
Document Lastmod	2006-12-29 16:23:19
Document Title	MFL34797004-Edit1
Document Creator	3.3: LaserWriter 8 8.7.1
Document Author:	sun

PREPARTION
■
To prevent the equipment damage, never plug in any power cords until
you have finished connecting all equipment.
1. Antenna (Analog or Digital)
PREPARATION
Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections.
For optimum picture quality, adjust antenna direction if needed.
Wall
Antenna
Socket
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
ANTENNA/
CABLE IN
Outdoor
Antenna
(VHF, UHF)
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Bronze Wire
Be careful not to bend the bronze
wire when connecting the antenna.
2. Cable
ANTENNA/
CABLE IN
Cable TV
Wall Jack
RF Coaxial Wire (75 ohm)
ANTENNA/
CABLE IN
UHF
Antenna
VHF
Signal
Amplifier
To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
■ If the antenna is not installed properly, contact your dealer for assistance.
■
■
! NOTE
14
The TV will let you know when the analog, cable, and digital channel scans are complete.
EXTERNAL EQUIPMENT SETUP
HD RECEIVER SETUP
This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you
do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown
below.
1. How to connect
OPTICAL
(MONO)
DIGITAL AUDIO
OUT
S-VIDEO
VIDEO
AUDIO
AV IN 1
Connect the audio output of the digital set-top box to
the C O M P O N E N T I N A U D I O 1 jacks on the set.
AV OUT
AUDIO
COMPONENT IN
VIDEO
Connect the video outputs (Y, PB, PR) of the digital set
top box to the C O M P O N E N T I N V I D E O 1 jacks on
the set. Match the jack colors
(Y = green, PB = blue, and PR = red).
EXTERNAL EQUIPMENT SETUP
When connecting Component cable
2. How to use
■
■
■
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
Select C o m p o n e n t 1 input source with using the
I N P U T button on the remote control.
PB
PR
If connected to C O M P O N E N T I N 2 input, select
C o m p o n e n t 2 input source.
Signal
Component 1/2
HDMI1/DVI,
HDMI2
480i
Yes
No
480p
Yes
Yes
720p
Yes
Yes
1080i
Yes
Yes
15
EXTERNAL EQUIPMENT SETUP
When connecting HDMI cable
1. How to connect
EXTERNAL EQUIPMENT SETUP
SERVICE
No separated audio connection is necessary.
RGB IN
(PC)
2. How to use
■
■
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
HDMI/DVI IN
RS-232C IN
(CONTROL & SERVICE)
If the digital set-top box supports Auto HDMI function, the
output resolution of the source device will be automatically
set to 1280x720p.
If the digital set-top box player does not support Auto HDMI,
you need to set the output resolution appropriately.
To get the best picture quality, adjust the output resolution of
the source device to 1280x720p.
REMOTE
AUDIO IN
(RGB/DVI) CONTROL IN
ANTENNA/
CABLE IN
Select H D M I 1 / D V I or H D M I 2 input source with using
the I N P U T button on the remote control.
! NOTE
16
Connect the digital set-top box to H D M I / D V I I N 1
or 2 jack on the set.
HDMI-DTV OUTPUT
When connecting HDMI to DVI cable
AUDIO
RGB IN
(PC)
ANTENNA/
CABLE IN
OPTICAL
RS-232C IN
(CONTROL & SERVICE)
DVI-DTV OUTPUT
DIGITAL AUDIO
OUT
(MONO)
S-VIDEO
VIDEO
AUDIO
AV IN 1
EXTERNAL EQUIPMENT SETUP
REMOTE
AUDIO IN
(RGB/DVI) CONTROL IN
AV OUT
HDMI/DVI IN
COMPONENT IN
VIDEO
SERVICE
1. How to connect
Connect the DVI output of the digital set-top box to the H D M I / D V I I N 1 or 2 jack on the set.
Connect the audio output of the digital set-top box to the A U D I O I N ( R G B / D V I) jack on the set.
2. How to use
■
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
■
Select H D M I 1 / D V I or H D M I 2 input source with using the I N P U T button on the remote control.
17
EXTERNAL EQUIPMENT SETUP
DVD SETUP
When connecting Component cable
1. How to connect
VIDEO
AUDIO
Connect the audio outputs of the DVD to the
C O M P O N E N T I N A U D I O 1 jacks on the set.
AV OUT
OPTICAL
2. How to use
■
■
■
■
(MONO)
DIGITAL AUDIO
OUT
S-VIDEO
VIDEO
AUDIO
Turn on the DVD player, insert a DVD.
Select C o m p o n e n t 1 input source with using the I N P U T
button on the remote control.
If connected to C O M P O N E N T I N 2 input, select
C o m p o n e n t 2 input source.
PB
PR
Refer to the DVD player's manual for operating instructions.
Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV
Video output ports
on DVD player
18
PB
PR
PB
PR
B-Y
R-Y
Cb
Cr
Pb
Pr
AV IN 1
EXTERNAL EQUIPMENT SETUP
Connect the video outputs (Y, PB, PR) of the DVD to
the C O M P O N E N T I N V I D E O 1 jacks on the set.
Match the jack colors
(Y = green, PB = blue, and PR = red).
COMPONENT IN
When connecting with an S-Video cable
AUDIO
1. How to connect
Connect the S-VIDEO output of the DVD to the
S - V I D E O input on the set.
Connect the audio outputs of the DVD to the A U D I O
input jacks on the set.
VIDEO
AUDIO
■
Select A V 1 input source with using the I N P U T button on
the remote control.
If connected to A V I N 2, select A V 2 input source.
■
Refer to the DVD player's manual for operating instructions.
■
OPTICAL
DIGITAL AUDIO
OUT
(MONO)
S-VIDEO
VIDEO
AUDIO
UDIO
AV IN 1
Turn on the DVD player, insert a DVD.
When connecting HDMI cable
EXTERNAL EQUIPMENT SETUP
AV OUT
2. How to use
■
COMPONENT IN
S-VIDEO
1. How to connect
Connect the HDMI output of the DVD to the
H D M I / D V I I N 1 or 2 jack on the set.
SERVICE
RGB IN
(PC)
No separated audio connection is necessary.
HDMI/DVI IN
REMOTE
AUDIO IN
(RGB/DVI) CONTROL IN
2. How to use
■
■
NTENNA/
CABLE IN
Select H D M I 1 / D V I or H D M I 2 input source with using
the I N P U T button on the remote control.
RS-232C IN
(CONTROL & SERVICE)
Refer to the DVD player's manual for operating instructions.
! NOTE
If the DVD supports Auto HDMI function, the DVD output
resolution will be automatically set to 1280x720p.
If the DVD does not support Auto HDMI, you need to set
the output resolution appropriately.
To get the best picture quality, adjust the output resolution
of the DVD to 1280x720p.
HDMI-DVD OUTPUT
19
EXTERNAL EQUIPMENT SETUP
VCR SETUP
VIDEO
AUDIO
To avoid picture noise (interference), leave an adequate distance between the VCR and TV
■ Use the ISM feature in the Option menu to avoid having a fixed image remain on the screen for a long period
of time. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on
the screen. This phenomenon is common to all manufactures and in consequence the manufactures warranty
does not cover the product bearing this phenomenon.
■
When connecting with an antenna
EXTERNAL EQUIPMENT SETUP
RGB IN
(PC)
HDMI/DVI IN
REMOTE
AUDIO IN
(RGB/DVI) CONTROL IN
ANTENNA/
CABLE IN
OPTICAL
S-VIDEO
VIDEO
ANT OUT
RS-232C IN
(CONTROL & SERVICE)
DIGITAL AUDIO
OUT
S-VIDEO
ANT IN
OUTPUT
SWITCH
Wall Jack
Antenna
1. How to connect
Connect the RF antenna out socket of the VCR to the A n t e n n a socket on the set.
Connect the antenna cable to the RF antenna in socket of the VCR.
2. How to use
■
Set VCR output switch to 3 or 4 and then tune TV to the same channel number.
■
Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)
AUDIO
20
VIDEO
(
VIDEO
When connecting with a RCA cable
1. How to connect
ANT IN
S-VIDEO
ANT OUT
OUTPUT
SWITCH
VIDEO
AUDIO
Select A V 1 input source with using the I N P U T button on
the remote control.
■ If connected to A V I N 2, select A V 2 input source.
■
OPTICAL
(MONO)
DIGITAL AUDIO
OUT
S-VIDEO
VIDEO
AUDIO
AV IN 1
Insert a video tape into the VCR and press PLAY on the
VCR. (Refer to the VCR owner’s manual.)
! NOTE
If you have a mono VCR, connect the audio cable from the
VCR to the A U D I O
L / M O N O jack of the set.
When connecting with an S-Video cable
1. How to connect
Connect the S-VIDEO output of the VCR to the
S - V I D E O input on the set.
Connect the audio outputs of the VCR to the A U D I O
input jacks on the set.
S-VIDEO
ANT OUT
OUTPUT
SWITCH
VIDEO
VIDEO
AUDIO
2. How to use
■
Select A V 1 input source with using the I N P U T button on
the remote control.
OPTICAL
DIGITAL AUDIO
OUT
If connected to A V I N 2, select A V 2 input source.
The picture quality is improved: compared to normal
composite (RCA cable) input.
VIDEO
AUDIO
CAUTION
! NOTE
(MONO)
S-VIDEO
AV IN 1
■
Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owner’s manual.)
AV OUT
■
COMPONENT IN
ANT IN
EXTERNAL EQUIPMENT SETUP
■
AV OUT
2. How to use
COMPONENT IN
V I D E O jacks between TV and
Connect the A U D I O/V
VCR. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red)
VIDEO
AUDIO
Do not connect to both Video
and S-Video at the same time. In
the event that you connect both
Video and the S-Video cables,
only the S-Video will work.
21
EXTERNAL EQUIPMENT SETUP
OTHER A/V SOURCE SETUP
Camcorder
1. How to connect
VIDEO
2. How to use
■
■
Select A V 2 input source with using the
I N P U T button on the remote control.
If connected to A V I N 1 input, select A V 1
input source.
Operate the corresponding external equipment.
This TV finds the connected input sources automatically for AV1, AV2, Component 1-2, RGB,
HDMI1/DVI and HDMI2 sources are connected.
AV IN 2
S-VIDEO
■
VIDEO L/MONO AUDIO R
EXTERNAL EQUIPMENT SETUP
V I D E O jacks
Connect the A U D I O/V
between TV and external equipment.
Match the jack colors.
(Video = yellow, Audio Left = white, and
Audio Right = red)
! NOTE
22
Video Game Set
PC SETUP
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
ERVICE
RGB IN
(PC)
When connecting D-sub 15pin cable
1. How to connect
HDMI/DVI IN
REMOTE
AUDIO IN
(RGB/DVI) CONTROL IN
Connect the PC audio output to the A U D I O I N
( R G B / D V I) jack on the set.
OPTICAL
RS-232C IN
(CONTROL & SERVICE)
2. How to use
■
■
Turn on the PC and the set.
Select R G B - P C input source in main input option of
SETUP menu. ( G p.67)
! NOTE
AUDIO
DIGITAL AUDIO
OUT
EXTERNAL EQUIPMENT SETUP
Connect the RGB output of the PC to the R G B I N
( P C) jack on the set.
RGB OUTPUT
Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or
brightness in PC mode. If noise is present, change the PC
output to another resolution, change the refresh rate to
another rate or adjust the brightness and contrast on the
VIDEO menu until the picture is clear. If the refresh rate
of the PC graphic card can not be changed, change the
PC graphic card or consult the manufacturer of the PC
graphic card.
23
EXTERNAL EQUIPMENT SETUP
When connecting HDMI to DVI cable
1. How to connect
EXTERNAL EQUIPMENT SETUP
Connect the DVI output of the PC to the H D M I / D V I
I N 1 or 2 jack on the set.
Connect the PC audio output to the A U D I O I N
( R G B / D V I ) jack on the set.
SERVICE
RGB IN
(PC)
HDMI/DVI IN
REMOTE
AUDIO IN
(RGB/DVI) CONTROL
ANTENNA/
CABLE IN
RS-232C IN
(CONTROL & SERVICE
2. How to use
■
■
Turn on the PC and the set
Select H D M I 1 / D V I or H D M I 2 input source with using
the I N P U T button on the remote control.
! NOTE
24
If the PC has a DVI output and no HDMI output, a separated audio connection is necessary.
If the PC does not support Auto DVI, you need to set the
output resolution appropriately. To get the best picture
quality, adjust the output resolution of PC graphics card's
output resolution to 1024x768, 60Hz.
DVI-PC OUTPUT
AUDIO
! NOTES
To get the the best picture quality, adjust the PC
graphics card to 1024x768, 60Hz.
Depending on the graphics card, DOS mode may
not work if a HDMI to DVI Cable is in use.
When Source Devices are connected with
HDMI/DVI Input, the output PC Resolution (VGA,
SVGA, XGA, WXGA), Position and Size may not fit
on the Screen. Press the ADJUST button to adjust
the screen Position of the TV SET and contact a
PC graphics card service center.
When Source Devices connected with HDMI/DVI
Input, output TV SET Resolution (480p, 720p,
1080i, 1080p) and TV SET Display fit EIA/CEA861-B Specification to Screen. If not, refer to the
Manual of HDMI/DVI Source Devices or contact
your service center.
If the HDMI/DVI Source Device is not connected
to the Cable or if there is a poor cable connection, "No signal" is displayed in the HDMI/DVI
Input. In this case, that Video Resolution is not
supported. If "Invalid Format" is displayed, refer to
the Source Device manual or contact your service
center.
Avoid keeping a fixed image on the screen for a
long period of time. The fixed image may become
permanently imprinted on the screen.
The synchronization input form for Horizontal
and Vertical frequencies is separate.
Supported Display Specifications
EXTERNAL EQUIPMENT SETUP
HDMI1/DVI-DTV, HDMI2-DTV mode
RGB-PC, HDMI1/DVI-PC mode
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
640x350
31.469
70.08
720x400
31.469
70.08
640x480
31.469
59.94
800x600
37.879
60.31
1024x768
48.363
60.00
1280x768
47.776
59.87
1360x768
47.720
59.799
1366x768
47.130
59.65
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
720x480
31.469
31.500
59.94
60.00
1280x720
44.960
45.000
59.94
60.00
1920x1080i
33.720
33.750
59.94
60.00
1920x1080p
27.000
33.750
24.00
30.00
* RGB-PC mode only: 640x350, 720X400
25
EXTERNAL EQUIPMENT SETUP
Screen Setup for PC mode
PICTURE
SOUND
CC
SAP
ADJUST
Overview
EXTERNAL EQUIPMENT SETUP
When RGB connect to PC output and select the RGB-PC in Input
source, this function is used.
When HDM/DVI connect to PC output and select HDMI/DVI input,
this function is used.
After connecting RGB-PC or HDMI/DVI to PC input and checking the
screen quality.
When you change the resolution, select the proper resolution in present input to see the best picture appearance.
Adjustment for screen Resolution, Position, Size,
and Phase
1024 x 768
1280 x 768
1360 x 768
1366 x 768
Press the A D J U S T button and then use D or E button to
select R e s o l u t i o n, P o s i t i o n, S i z e, or P h a s e.
Press the ENTER button and then use D E F G button to
make appropriate adjustments.
■ The P h a s e adjustment range is - 1 6 ~ + 1 6.
In HDMI/DVI-PC mode, Phase is not available.
■ The S i z e adjustment range is - 3 0 ~ + 3 0.
In HDMI/DVI-PC mode, S i z e is not available.
Press the ENTER button.
Initializing (Reset to original factory values)
Close
Resolution This function allows you select
resolution of XGA/WXGA.
Position This function is to adjust picture to
left/right and up/down as you prefer.
Size
This function is to minimize any vertical bars or stripes visible on the
screen background. And the horizontal screen size will also change.
Phase
This function allows you to
remove any horizontal noise and
clear or sharpen the image of characters.
To initialize the adjusted values
Press the A D J U S T button and then use D or E button to
select R e s e t.
Press the ENTER button and then use F or G button to
select Y e s.
26
Press the ENTER button.
Close
AV OUT SETUP
The TV has a special signal output capability which allows you to hook up the second TV or monitor.
NT IN
1. How to connect
ICAL
L AUDIO
UT
(MONO)
S-VIDEO
VIDEO
AUDIO
! NOTE
Component1-2, RGB-PC, HDMI1/DVI, HDMI2, DTV input
sources cannot be used for AV out.
We recommend to use the AV OUT jacks for VCR recording.
VIDEO
S-VIDEO
DIGITAL AUDIO OUTPUT
EXTERNAL EQUIPMENT SETUP
See the Operating Manual of the second TV or monitor
for further details regarding that device’s input settings.
AV IN 1
Connect the second TV or monitor to the TV’s AV OUT
jacks.
AV OUT
Send the TV’s audio to external audio equipment via the Digital Audio Output (Optical) port.
1. How to connect
Connect one end of an optical cable to the TV Digital
Audio (Optical) Output port.
Connect the other end of the optical cable to the
digital audio (optical) input on the audio equipment.
Set the “TV Speaker option - Off” in the AUDIO
menu. (G p . 8 4). See the external audio equipment
instruction manual for operation.
(PC)
REMOTE
AUDIO IN
(RGB/DVI) CONTROL IN
OPTICAL
RS-232C IN
(CONTROL & SERVICE)
DIGITAL AUDIO
OUT
S-VIDEO
VIDEO
! NOTE
When connecting with external audio equipments, such as amplifiers or speakers, please turn the TV speakers off. (G p . 8 4)
CAUTION
Do not look into the optical output port. Looking at the
laser beam may damage your vision.
27
WATCHING TV / CHANNEL CONTROL
REMOTE CONTROL FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
MODE Select the remote operating mode: TV, DVD, VCR,
AUDIO, CABLE or STB.
INPUT
TV INPUT
POWER
VCR/DVD Control video cassette recorders or DVD players.
control buttons
MENU Displays the main menu.
BRIGHT -/ +
AUDIO
Adjust the brightness on screen.
It turns to the default settings brightness by changing
mode source.
WATCHING TV / CHANNEL CONTROL
HT -
BRIG
MENU
VCR
STB
BRIG
HT +
THUMBSTICK Navigate the on-screen menus and adjust the system set(Up/Down/Left tings to your preference.
Right/ENTER)
ENTER
EXIT Clear all on-screen displays and return to TV viewing
from any menu.
TIMER Select the amount of time before your TV turns off automatically. G p . 9 0
EXIT
INK
TIMER
RATIO
SIMPL
RATIO Change the aspect ratio. G p.92-93
VOL
MUTE
FAV
CH
SIMPLINK C? G p.92-93
VOLUME UP Increase/decrease the sound level.
/DOWN
MUTE Switch the sound on or off. G p.38
FAV Scroll through the programmed Favorite channels.
CHANNEL Select available channels.
UP/DOWN
NUMBER button
— (DASH) Used to enter a program number for multiple program
channels such as 2-1, 2-2, etc.
BACK Tune to the last channel viewed.
Illuminates the remote control
LIGHT buttons of selected mode.
28
DVD
MODE
CABLE
TV
BACK

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 15
Has XFA                         : No
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:d700eec0-81b6-4160-84f4-8021bbdd94ac
Modify Date                     : 2006:12:29 16:23:19+09:00
Create Date                     : 2006:12:29 16:19:16+09:00
Metadata Date                   : 2006:12:29 16:23:19+09:00
Document ID                     : uuid:45e75b87-ebc8-4773-9c6c-47a84bcd36c3
Format                          : application/pdf
Title                           : MFL34797004-Edit1
Creator                         : 3.3: LaserWriter 8 8.7.1
Author                          : sun
Producer                        : Acrobat Distiller 4.0.5  for Macintosh

EXIF Metadata provided by EXIF.tools