LG Electronics USA 9SD751TVDA WIRELESS MOTION SENSOR User Manual

LG Electronics USA WIRELESS MOTION SENSOR

Contents

User Manual

MFL68488801Please read this manualcarefully before using the product.1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.2. All electrical and electronic products shall be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.※ Check out below address for more information.9SD751TVDAWIRELESS HIGHBAY SENSOROWNER’S MANUALSpecificationsDisposal of your old applianceModel 9SD751TVDASensorFrequencyWireless rangeOperating conditionsTemperatureHumidity WeightDimensions (WHD)installation height Operating voltageCurrent consumptionFCC IDPassive Infrared(PIR) Sensor2405~2480 MHz, 16 chLine of sight 98 ft (30 m)For Indoor use onlyOperating : -4 to 122℉ (-20 to 50℃)Storage : -22 to 185℉ (-30 to 80℃)0 to 85 % Rh1.1 oz (30 g)2.6” x 2.1” x 1.0” (75 mm x 54 mm x 25 mm)Typical 20 ft (6 m), up to 40 ft (13 m)3.3 V DC (from LG LED lighting) Max.80 mA BEJ9SD751TVDAhttp://www.lg.com/global/sustainability/environment/Dimensions Safety PrecautionsFeatures- 1 - - 2 -54 mm17 mm54mm75 mm25mm11 mm- Wireless Highbay sensor detects motion and control LG LED Highbay efficiently. Simple installation just by pluging a sensor Easy adjustment usinga rotary dial and a switch Wireless communication at 2.4 GHz Possibleto be used for LG Lighting control system.ApplicationsHigh ceiling spaces Like Warehouse, Storage areas, etc.WARNINGViolation of warnings may lead to serious injury or death.CAUTIONViolation of precautions may lead to light injury or product damage.• Turn power offbefore install theproduct.• Do not wipe the surfacewith inflammables suchas alcohol, benzene and acetone.• Do notdisassemblethe product.• Turn power off before installthe product.• Do not installnearby inflammablematerial• Do not install in areasthat have risks offlooding Do not storein a humid area.• Do not install nearby air conditioners andheaters.
- 5 - - 6 -Installation LED operationAdjustment• Delay time :occupancy• initializedbutton• Dimming level :non-occupancyIt is possible to changea delay time from 30 secto 20 min with the rotarydial. (default : 10 min)Press the buttonover 5 seconds. IfRED LED flashesrapidly for 3 seconds,it is initializedIt is possible to choose non-occupancy dimming level,OFF or DIM (default : OFFstate) If you choose DIM,LG LED Lighting is dim whenthere is nobody. If you want to use it for larger areas than one detect area, installmultiple sensors and set wireless connection. For further details,see xx page and contact the dealer that you purchased this product.Avoid metal andreinforced concretewalls etc, amongsensors if you wantto use it for LGLighting controlsystem.You haveto plug thesensorcompletely.WARNING- 3 - - 4 -Plug the sensor to interface port on compatible LG LED lighting.Flashes once : occupancy detectionFlashes twice : occupancy detection while Lighting System interworking ModeFlashes four times : setting completion by wireless setting tool On for 30 seconds after power-up : stability time Rapid flashes for 3 seconds : initializedRapid flashes continuously : It is connected to non-compatible LG LEDLighting so it cannot work normally Very rapid flashed for 2 seconds : it is hold state about manual setting andnetwork connection state.TroubleshootingIt is probably not detect motion. It is not flashes RED LED.• Check the settings by wireless setting tool. It is possible to select RED LED OFF.• Check the detection area. • Make sure installation state. you have to plug the sensor completely. • On specific operating temperature from 90℉(32℃) to 104℉(40℃), It may not detect motion.Lighting is not OFF although nobody is occupancy. • Make sure installation state. you have to plug the sensor completely.• Check the delay time and dimming level non-occupancy. If delay times is too long or diming level is DIM state, lighting may be not OFF. Motion detection is strange. It detects motion abnormally.• Check the installation environment. If there are air conditioner or heater, it should works abnormally.• Check the installation state. LED lighting plugged with sensor have to fix on ceiling and not shake. Detection Areainstallation height : typical 20 ft (6 m), up to 40 ft (13 m)• Side view• Federal Communications Commission (FCC) Statementdiameter 40 ft (12.2 m)diameter 20 ft (6.1 m)0m36.19.112.26.1200m0ft6.1200ft10203040You are cautioned that changes or modifications not expressly approvedby the part responsible for compliance could void the user’s authority tooperate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interferencethat may cause undesired operation of the device of the device.• FCC CautionAny changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment and For indoor use only, use outdoors or in other modes not covered by this manual may violate the FCC regulation and violate the user authority to use the product.• FCC WARNINGThis equipment may generate or use radio frequency energy.Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual.The user could lose the authority to operate this equipment if an nauthorized change or modification is made• FCC RF Radiation Exposure StatementThis equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. LG Electronics hereby declares declares that this product is incompliance with the following Directives.R&TTE Directive 1999/5/EC EMC Directive 2004/108/ECLOW VOLTAGE Directive 2006/95/ECThe products described above comply with the essential requirements of the directives specified. This device is a 2.4GHz wideband transmission system, intended for use in all EU member states and EFTA countries. Contact office for compliance of this product:LG Electronics IncEU Representative, Krijgsman 1,1186 DM Amstelveen, The NetherlandsPlease note that this is NOT a Customer Servicecontact point. For Customer Service Information,see Warranty Card or contact the dealer that youpurchased this product.Indoor use only.CE Notified Body statement.This is a class B product. In a domestic environment,this product may causes radio interference,in which case the user may be required to take adequate measures.

Navigation menu