LG Electronics USA JS750 Cellular/PCS GSM/WCDMA/EDGE Phone with WLAN and Bluetooth User Manual Layout 1

Download:
Mirror Download [FCC.gov]
Document ID	1297318
Application ID	GajPuYhWuZYVlQ1TiQV7UQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	72.36kB (904548 bits)
Date Submitted	2010-06-16 00:00:00
Date Available	2010-12-13 00:00:00
Creation Date	2017-11-09 04:26:40
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-11-09 04:26:40
Document Title	Layout 1
Document Creator	QuarkXPress(tm) 6.52

Technical Details
FCC RF Exposure Information
WARNING! Read this information
before operating the phone.
In August 1996, the Federal
Communications Commission (FCC)
of the United States, with its action
in Report and Order FCC 96-326,
adopted an updated safety standard
for human exposure to Radio
Frequency (RF) electromagnetic
energy emitted by FCC regulated
transmitters. Those guidelines are
consistent with the safety standard
previously set by both U.S. and
international standards bodies. The
design of this phone complies with
the FCC guidelines and these
international standards.
Bodily Contact During Operation
This device was tested for typical
use with the back of the phone
kept 0.79 inches (2.0 cm) from
the body. To comply with FCC RF
exposure requirements, a minimum
separation distance of 0.79 inches
(2.0 cm) must be maintained
between the user’s body and the
back of the phone, including the
antenna. Third-party belt-clips,
holsters, and similar accessories
containing metallic components
should not be used. Avoid the use
14 JS750
of accessories that cannot maintain
0.79 inches (2.0 cm) distance
between the user’s body and the
back of the phone and have not
been tested for compliance with
FCC RF exposure limits.
Vehicle-Mounted External Antenna
(Optional, if available.)
To satisfy FCC RF exposure
requirements, keep 8 inches (20
cm) between the user / bystander
and vehicle-mounted external
antenna. For more information
about RF exposure, visit the FCC
website at www.fcc.gov.
FCC Notice and Cautions
This device and its accessories
comply with part 15 of FCC rules.
Operation is subject to the
following two conditions: (1) This
device and its accessories may not
cause harmful interference, and (2)
this device and its accessories must
accept any interference received,
including interference that causes
undesired operation.
Any changes or modifications not
expressly approved in this user
guide could void your warranty for
this equipment. Use only the
supplied antenna. Use of
unauthorized antennas (or
modifications to the antenna)
could impair call quality, damage
the phone, void your warranty
and/or violate FCC regulations.
Don't use the phone with a
damaged antenna. A damaged
antenna could cause a minor skin
burn. Contact your local dealer for
a replacement antenna.
Part 15.21 statement
Changes or modifications that are
not expressly approved by the
manufacturer could void the user's
authority to operate the
equipment.
Part 15.19 statement
This device and its accessories
comply with part15 of FCC rules.
Operation is subject to the
following two conditions:
(1) This device & its accessories
may not cause harmful
interference.
(2) This device & its accessories
must accept any interference
received, including interference
that may cause undesired
operation.
Part 15.105 statement
This equipment has been tested
and found to comply with the limits
for a class B digital device, pursuant
to Part 15 of the FCC Rules. These
limits are designed to provide
reasonable protection against
harmful interference in a residential
installation. This equipment
generates, uses, and can radiate
radio frequency energy and, if not
installed and used in accordance
with the instructions, may cause
harmful interference to radio
communications. However, there is
no guarantee that interference will
not occur in a particular installation.
if this equipment does cause
harmful interference or television
reception, which can be determined
by turning the equipment off and
on, the user is encouraged to try to
correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving
antenna.
- Increase the separation between
the equipment and receiver.
- Connect the equipment into an
outlet on a circuit different from
that to which the receiver is
connected.
- Consult the dealer or an experienced
radio/TV technician for help.
JS750 15
Chapter 1 Getting Started
1.1 About Your Phone
Your JS750 phone allows you to keep in touch with friends and family back
home when traveling to another country or outside your network carrier
service area.
1.2 Getting to Know Your Touch Phone
Front panel
1. Notification LED LED lights blue when there are pending
notifications, lights red when charging, and lights green when fully
charged.
2. Earpiece Allows you to hear the caller.
3. Light and Proximity Sensor Senses the ambient light and adjusts the
screen backlight accordingly. Will also lock the screen during a call, so
that keys are not accidentally pressed.
4. LCD Screen Allows you to view incoming calls, messages and icon
indicators as well as a wide variety of content you select for viewing.
5. End Key Use to end a call. Also returns to the Today Screen.
6. Start Key Press to open the Start menu.
7. SEND Key Use to make and answer calls. Press and hold to activate
voice commands.
16 JS750
Top panel
8. Power/Lock(Unlock) Key Press and hold to turn the power on/off.
Press to lock and unlock the phone.
Back panel
9. Speaker Lets you hear the caller's voice in speakerphone mode. Also
lets you hear music and video sounds.
10. Camera Lens Use to take pictures and record video. Keep it clean
for optimal image quality.
11. Stylus Use to activate the Touch screen commands with ease. The
slot allows for convenient storage so your stylus is always at hand.
Left panel
Right panel
12. Headset Jack Allows you to plug in an optional 3.5mm headset for
convenient, hands-free conversations.
13 . Volume Keys Use to adjust the Master Volume in standby mode
and the Earpiece Volume during a call.
14 . Accessory/Charger Port Cover
15 . Reset Key Resets your phone (will end all applications currently
running).
16 . Accessory/ Charger Port Connects the phone to the battery
charger, or other compatible accessories.
17 . microSD™ Slot Accommodates an optional microSD™ card.
18 . Task Manager Key Allows you to view all programs currently
running on the device and corresponding memory usage. Also
allows you to end or go to those tasks.
19. Camera/Video Key Press for quick access to the Camera function.
Press and hold this key to record a video.
JS750 17
Getting Started
1.3 Qwerty Keyboard
The Qwerty keyboard allows you to quickly and easily enter any kind of
data, whether it's a message (Text, Picture or Video), an Office file (Word,
Excel, Powerpoint or OneNote), or when using the Internet.
1. QWERTY Keypad Use to enter numbers and characters and select menu items.
2. Email Tab Key Use to access E-mail account(s) to send/receive email messages.
3. Sym Key Use to insert symbols when entering text. Press the key, then touch the symbol on screen or press the
Qwerty key that corresponds with the onscreen symbol. Press the Sym Key again to exit from symbol mode.
4. Caps/ Shift Key Use to change letter case when typing.
5. Fn Key Use to insert symbols (at the top of each Qwerty key) into text or change input function from abc to
XT9.
6. Vibrate Key Use to turn Vibrate mode on/off (From the Today Screen, press and hold for about 3 seconds).
7. Space/Voice Command Key Use to enter a space while entering text. From the Today Screen, press to access
the call history or hold down for 3 seconds to access Voice Commands.
8. International Dial Key Press and hold the International Dial Key to display the + symbol. The symbol
automatically inserts the exit code for the country from which you are calling.
9. Speakerphone Key Use to activate Speakerphone during a call.
10. Back Key Press to return to back out of menus.
11. OK Key Use to activate a selected screen item.
12. Directional Key Use for quick, convenient navigation. In menus use to scroll to choices and settings.
13. Clear Key Press to delete a single space or character, or press and hold to delete a specific word plus its space.
14. Return Key Moves cursor to the next line.
18 JS750
1.4 Menus and Applications Overview
Today Screen Menu
picture
pictures
music
Start Menu
Inicio
Teléfono
phone
fav
favorite
orite contact
contactss
Texto
xto
voicemail
E-mail
clock
Contact
os
ontactos
get
getting star
star ted
Visual Voice
Voice Mail
message
message
e-mail
Mobile Email
calendar
Mobile IM
fav
favorite
orites
City
City ID
Interne
Internett Explorer
Explorer
JS750 19
Getting Started
Configuración
onfiguración
Reloj y alarmas
Inicio
Bloquear
Sonidos y notificaciones
Conexiones
Administrador de conexiones ina
Cambiar USB
Conexiones
Conexión del navegador
Configuración GPRS
Insctipción en dominio
USB a PC
WI-Fi
Información del sisterma
Informe de errores
Limpiar Almacen.
Luz de fondo
Memoria
Pantalla
Programas administrados
Qualcomm Control Panel
Quitar programas Sensor
Microsoft My Phone
Bluetooth
Bloquear tecla
RSSVie
wer
SSView
Personal
Cotones
Datos propietario
Teléfono
Voice Commands
Sistema
Acerca de
Administrador de tareas
Cerrificados
Cifrado
Comentarios del cliente
Configuración regional
Energía
GPS externo
20 JS750
Alarmas
Alarmas
Calendario
Tarea
areass
Not
Notas
Explorador
os
Explorador de archiv
archivos
Office Mobile
Microsoft
Microsoft My Phone
Imágenes
Imágenes y vídeos
MSN Money
Money
Window
indows Media
MSN El Tiempo
Tiempo
World Clock
Cámera
Cámera
Buscar Teléfono
Teléfono
Introducción
Introducción
Calculadora
Calculadora
Active
ctive Sync
Sync
Adobe Reader
Reader LE
Window
indows Live
Live
Voice Commands
Commands
Juegos
Solitario
Administrador
dministrador de
tarea
areass
Marke
Marketplace
NOTES :
●
All screen shots in this guide are
simulated. Actual displays may vary.
●
Instructions to perform tasks in this
guide may change depending on the
software version of your phone.
●
Unless specified otherwise, all
instructions to perform tasks in this
guide assume that you are starting
from the Today screen.
JS750 21
Getting Started
1.5 Installing the Battery
and Storage Card
The Battery
NOTE It is important to fully charge the
battery before initial use of the phone.
The phone comes with a
rechargeable battery. Keep the
battery charged while not in use in
order to maximize talk and standby
time. The battery charge level is
shown at the top of the LCD screen.
Removing the Battery
Turn power off. Apply steady
downward pressure to the center of
the battery cover release it. Remove
the cover, then use the fingertip
cutout to lift the bottom edge of
the battery out.
Installing the Battery
To install the battery, insert the top
edge (aligning the battery
terminals) of the battery into the
opening on the back of the phone.
Push the battery down until it clicks
into place. Place the top edge of
battery cover with the tabs and
slots aligned, then apply steady
upward pressure until it clicks into
place.
Installing the microSD
1. Remove the microSD card slot
cover.
2. Push the microSD card into the
slot with its gold contacts facing
down until it clicks into place
and then replace the slot cover.
22 JS750
1.6 Charging the Battery
Your JS750 phone device comes
with a cableless wall adapter and a
USB data cable which connect
together to charge your phone. To
charge your phone:
NOTICE
Please use only an approved charging
accessory to charge your LG phone.
Improper handling of the charging port, as
well as the use of an incompatible charger,
may cause damage to your phone and
void the warranty.
NOTICE
Please make sure that the side with the
USB symbol faces up before inserting a
charger or data cable into the charger
port of your phone.
Battery Charge Level
You can find the battery charge
level at the top right of the LCD
screen. When the charge level
becomes low, the phone blinks the
battery icon, and displays a warning
message. As the charge level
approaches empty, the phone will
turn off. Unsaved items may be lost.
JS750 23
Getting Started
Charging with USB
You can use your computer to
charge your phone. Connect one
end of the USB cable to the
charging accessory port on your
phone and the other end to a
highpower USB port on your PC
(commonly located on the front
panel of the computer). It is best to
use the rear USB port when
connecting to a desktop PC. A USB
Hub should be powered by an
external power source (see Note
below).
NOTES ● Low-power USB ports are not
supported, such as the USB
port on your keyboard or buspowered USB hub.
●
When the device needs to
charge from USB port of the
computer, the necessary USB
driver should be first installed
on the computer.
- When the device is in, LG
USB Modem Driver should be
installed in advance for USB
charging.
- When the device is in
ActiveSync mode as a default
setting, the computer needs
ActiveSync program including
USB driver to be installed for
USB charging.
24 JS750
- On the other hand, you do not
need to install the specific
driver for USB charging when
the device is in USB Mass
Storage, because OS like
Windows has the driver.
●
Another way for USB charging
with ActiveSync mode
1 Press the Start Key
, tap
Settings
, tap Connections
, and then tap USB to PC.
2. Unchecked "Enable advanced
network functionality.
1.7 Starting Up
Turning the power on and off
Turning the Phone On
1. Press and hold the Power/Lock
Key
for a couple of
seconds.
NOTE When you turn on your phone
for the first time, follow the
instructions on the screen to
activate your device.
Turning the Phone Off
1. Press and hold the Power/Lock
Key
for a few seconds.
2. Tap Yes to confirm that you want
to shut down the device.
1.8 Today Screen
The Today Screen provides quick access to various frequently used device
programs and applications. It also displays the Notification and Status Icon
taskbar and the Options taskbar for additional quick and easy access options.
Notification and Status
Icon taskbar
See "Notification and Status
Icon Taskbar" below for details.
Today Screen
See "Today Screen"
on page 50 for
details.
Current selection
Start icon
Tap to open the
Start menu.
Options taskbar
Contacts Icon
Tap to open Contacts panel.
See "Options Taskbar" on page
28 for details.
Options Icon
Options will depend on the selected menus.
1.9 Notification and Status Icon Taskbar
The Icon taskbar displays a variety of icons to let you know device status
and notification of events. Status icons can include connectivity, network,
signal strength, volume, battery and time. Notifications can include missed
calls, new SMS/MMS messages, and more. The following is an example of
the icons you may see on the Icon taskbar.
JS750 25
Getting Started
Tap the Icon taskbar to display a drop-down menu that allows you to zoom,
access the wireless manager for network connection status, change volume,
see remaining battery power, set the Clock/Alarm, and more.
Notification and Status
Icon taskbar
Drop-down taskbar
1.10 Options Taskbar
The Options Taskbar displays options that are dependent on the current
menu or function.
Today Screen Options Taskbar
The Today Screen Options taskbar includes access icons for the Start
screen
, and Contacts list Contacts .
NOTE If you have new notifications waiting, the Notifications icon
displayed instead.
26 JS750
Notifications
will be
1.11 Start Menu
The Start menu is home to all the programs, applications and settings of
your Windows Phone-powered device, giving you complete access at the tip
of your finger.
To open the Start screen press the Start Key
at the bottom center of
the phone or tap the Start icon
in the Options taskbar on the lower left
corner of the LCD.
Tap to return to the
Today Screen.
Notification and Status
Icon taskbar
Flick up or down to scroll the screen.
Tap an icon to launch it.
Options taskbar
Lock icon
Tap to temporarily lock.
See page 30 for details.
Close icon
Tap to close the Start menu.
To launch a program application or open a panel, simply tap the
program icon.
JS750 27
Getting Started
1.12 Lock
Locking the Phone
You can lock your phone to guard
against accidental or intentional
use. Press the Power/Lock Key
to lock your phone.
Unlocking the Phone
To unlock your phone, press the
Power/Lock Key
to turn the
screen on. Then, touch and slide
the Lock icon
to either left or
right. If you wish, you can set the
phone to require a password before
it is unlocked. To set up a password
requirement, go to the Lock menu
(Start
> Settings
> Lock
).
Unlocking with Gestures
Another option to unlock your
phone is available that allows you to
Locked Screen
28 JS750
go to a specific function. Gestures
allows you to perform the gesture
on the lock screen. For Gestures
information, go to the Gesture
Unlock page on the Lock menu
(Start
> Settings
> Lock
scroll to Gesture Unlock page).
To go to the Calendar from the
Lock screen, follow the images
below:
Sleep Mode
Sleep mode automatically locks the
phone against accidental actions
and conserves battery power. While
in Sleep mode, only the Power/Lock
Key
at the top edge of the
phone will wake up your phone.
The phone automatically enters
Sleep mode after a period of
inactivity.
Gesture Entered on
Locked Screen
Activated Gesture
NOTE If a phone password is required to
unlock, you will be prompted for
the password when you unlock
the phone.
Unlocking the Phone
The steps and instructions in this
guide begin with the screen already
unlocked. If your phone screen is in
sleep mode, press the Power/Lock
button on the top side of the
phone. Then, slide the Unlock icon
to the left, or right, to unlock the
screen.
could be accidental. To unlock the
screen, touch and slide a displayed
icon. For instance, to answer an
incoming call, touch and slide the
Answer icon
to the right.
Tracking notifications on the Lock
panel
Your phone keeps track of
notifications not responded to on
the lock screen. When the screen is
locked, the Lock icon shows the
number of pending notifications,
including missed calls, new
messages and upcoming
appointments.
To view notifications on the Lock
panel
1. On the Lock screen, tap the Lock
icon (
). Notification icons
representing each type of
notification are then displayed
below the Lock icon.
Notifications on the Lock
panel
Your phone still alerts you to
incoming calls and alarms even if the
screen is locked. The device only
responds to a deliberate touch and
slide action, not to simple taps which
2. Slide a notification icon right or
left to view the respective
information. For instance, slide
the Missed Call icon to view your
list of missed calls.
JS750 29
Getting Started
1.13 Adjusting the Volume
A single Volume Control panel
adjusts both the system volume
(notifications and audio/video
playback volume) and the phone
ring volume of your phone.
Accessing the Volume Control panel
To open the Volume Control panel:
●
●
Press the Volume Keys
left side of the phone.
To change volume settings using
the Volume Keys
1. Press the side volume keys
2. Tap the volume bar you want to
adjust, then press the Volume
Up/ Down Key
to adjust the
volume level. You can also:
●
Tap Vibrate to switch to vibrate
mode.
●
Tap Off to mute the volume.
on the
Tap the Volume Control icon in
the Status Icon taskbar.
NOTE The Volume Control panel
automatically closes after a few
seconds if accessed by pressing
the Volume Keys. If accessed from
the Status Icon taskbar, tap OK
to close the panel.
NOTE If you press the Volume Down Key
repeatedly, both volumes are
silenced.
To change volume settings using
the volume bars
1. Open the Volume Control panel.
2. Tap or drag your finger up/down
either of the volume bars. You
can also:
●
Tap Vibrate to switch to vibrate
mode.
●
Tap Off to mute the volume.
NOTE Use the Volume Up / Down Key
on the left side of your phone
to adjust the conversation phone
volume during an ongoing call.
30 JS750
1.14 Finger Movement
Gestures
●
To scroll up, drag your finger
downward on the touch screen.
The touch screen is sensitive to
fingertip movements allowing you to
scroll and pan with ease.
●
To auto-scroll, flick your finger
upward or downward on the
touch screen. Tap the screen to
stop scrolling.
Finger scrolling
Finger scrolling is available in all
directions (up and down or left and
right) and can be used to move
through web pages, documents, and
lists (like the Contacts, file,
message, calendar, and
appointments lists).
To scroll up and down
●
To scroll left and right
●
To scroll towards the right, drag
your finger to the left.
●
To scroll towards the left, drag
your finger to the right.
●
To auto-scroll, flick your finger
left or right. Tap the screen to
stop scrolling.
To scroll down, drag your finger
upward on the touch screen.
When finger
scrolling, drag or
flick your finger
on the touch
screen.
JS750 31
Finger panning
1.15 Using the Zoom Bar
Finger panning doesn't limit you to
opposite 90 degree directions. You
can use finger panning to move to
and view other parts of a zoomed-in
photo, web page, document, or an
email. To pan, touch and keep your
finger on the touch screen, then
drag your finger in any direction.
Your JS750 phone has a handy and
unique zoom control tool right on
the touch screen. When viewing a
Web page in the Web browser,
touch the Menu icon
to display
the Zoom bar. Simply slide your
finger across the Zoom bar to easily
set the zoom to the level that's best
for you.
32 JS750
Changing Networks with Your
JS750
Network
tab
You can change network modes
manually in phone settings.
To change networks manually
1. From the Today Screen, tap the
Notification and Status Icon
taskbar.
2. Tap the connections indicator
to access the following
menu.
5. Tap
under Mode of
operation, then tap the network
you want to set.
●
GSM/UMTS Mode: access GSM
networks only.
6. Tap
OK
to save settings.
Settings
3. Tap Settings.
4. Scroll horizontally (at the top of
the screen) to the Network tab.
JS750 33
Chapter 2 Using Phone Features
2.1 Making Calls with the
Phone Dialpad
The phone's dialpad allows you to
manually dial a number, or select a
number stored in the phone's
memory.
To open the phone's dialpad, press
the SEND Key
To call a phone number or contact
1. Press the SEND Key
, then
begin entering the first few
numbers or characters by tapping
the keys. If you tap a wrong
number or character, tap Delete
to erase each mistake. Touch
and hold Delete
to erase the
entire entry.
Smart Dial
Your JS750 phone has a Smart Dial
feature that makes it quick and easy
to call any number stored in your
phone's memory. As you start
entering either numbers or letters
on the Phone panel, Smart Dial
automatically searches for matches
in Contacts and call history and lists
them. Just tap an entry on the list,
then press the SEND Key
to
call it.
34 JS750
NOTE By default, a numeric touch
keypad is displayed for you to
enter numbers. If you want to
enter letters instead, in the
Options taskbar, tap Hide Keypad
, then tap Show Keyboard
2. The list of matching entries is
displayed above the touch keys.
Tap Hide
to view the list
only. Slide (or flick) your finger
up or down to scroll through the
list.
3. To call from the list, tap the
desired entry, then tap the
phone number to call.
TIPS
●
Depending on the information
saved on each contact, Smart
Dial will make it easy to place a
call, send a text or email to that
contact.
Making a call from a text
message
While you are viewing a text
message, you can directly call the
sender of the message.
1. While viewing the text message,
press the SEND Key
2. A verification message appears
with the phone number from the
text message. To call the
displayed number, press the
SEND Key
Tapping a phone number that is
displayed in the body of the text
message also allows you to call that
number.
JS750 35
Using Phone Features
Making a call from an email
message
While viewing a received email
message, you can directly place a
call to the sender of the message.
Tap a phone number that is
displayed in the body of the email
message to call that number.
Making a call from a meeting
request or reminder
When you receive a calendar
reminder or meeting request email
that contains a phone number, you
can tap the number to directly
place the call.
For example, if you are traveling and
need to join a conference bridge
call back in the home office, rest
assured that you can join the call
without delay. Appointment
reminders you receive on your
phone will conveniently display the
phone number and PIN, ready for
you to dial.
If you made a call from a meeting
request email, you can view the
meeting details in the email directly
on the Phone panel while the call is
in progress. An email indicator is
shown on the Keypad key. Tap this
icon to view the meeting details.
36 JS750
Making an emergency call
Even if the phone is locked, slide
the slider to unlock the screen, then
tap 911 (where you would enter
your lock code). Then press the
SEND Key
to place the call.
Making an international call
To make an international call, you
need to press and hold the
International Dial Key
to replace
the international prefix of the
country that you are calling. After
the plus sign, enter the full phone
number which includes the country
code, area code (without the leading
zero, if any), and phone number.
1. Press the SEND Key
, then
tap and hold the number 0 key
on the dialpad until the plus (+)
sign appears.
2. Enter the full phone number you
want to dial, then press the
SEND Key
on your phone.
Assisted Dialing
Assisted Dialing allows you to easily
dial international calls while roaming
in another country. When enabled,
Assisted Dialing On appears in the
Phone panel.
To turn Assisted Dialing on
1. Press the SEND Key
to
display the Phone panel.
4. Use the Keypad
to make the
changes you want.
5. Tap
Done
2. Tap Options
in the Options
taskbar, then tap Assisted
Dialing.
To reset Assisted Dialing to the
default
3. Tap the check box next to Enable
Assisted Dialing.
1. Press the SEND Key
to
display the Phone panel.
4. Tap Change
next to
Reference Country / Region.
2. Tap Options
in the Options
taskbar, then tap Assisted
Dialing.
5. Tap the country you want to call,
then tap Save .
6. Tap
Done
To edit a country’s international
call settings
1. Press the SEND Key
to
display the Phone panel.
2. Tap Options
in the Options
taskbar, then tap Assisted
Dialing.
3. Tap any of the call settings,
including Country code, IDD
Prefix (International Direct Dial),
NDD Prefix (National Direct
Dial), Area/City Code and
National Number Length (length
of phone number).
3. Tap Menu
taskbar.
Menu
in the Options
4. Tap Restore Default, then tap
Done .
Calling voice mail
Speed Dial Number 1 is generally
reserved for your voice mail. Touch
and hold this key on the phone's
dialpad to call voice mail and
retrieve your voice mail messages.
You can also double-tap (visual*)
voicemail from the Today Screen.
*After subscribing to Visual
Voicemail, the option name on the
Today Screen will change to Visual
Voicemail.
JS750 37
Using Phone Features
2.2 Answering and Ending
Calls
To reject a call
When you receive a phone call, the
Incoming message will appear,
allowing you to either answer or
ignore the call.
●
Tap Menu in the Options
taskbar, then tap Ignore.
●
Press the End Key
If you can't take a call, you can
reject it and automatically reply to
the caller with a text message
instead. When the phone alerts you
to a call:
To answer a call
Do either of the following:
Tap
●
Press the SEND Key
Answer
To reject a call and send a text
message
Accepting or rejecting an
incoming voice call
●
Do either of the following:
1. Tap Menu in the Options
taskbar, then tap Respond with
text message.
2. Tap the text message you want
to respond with, such as I'm in a
meeting; I'll call you later.
3. Tap Send
taskbar.
Send
in the Options
To accept a phone call when the
phone is locked
You can receive an incoming call
when the phone is locked. When
the phone is locked, the following
screen is shown when you accept
the call:
38 JS750
Call Waiting
Your phone notifies you when you
have another incoming call, and
gives you the option of rejecting or
accepting the call. If you are already
on a call and accept the new call,
you can choose to start a three-way
call for all participants.
To use the speakerphone
Touch and slide the onscreen touch
key (Answer or Ignore).
Using the call functions
When a call is in progress, use the call
function buttons to put a call on
hold, dial another contact for a threeway phone, enter notes about the
conversation, and more.
During a call, do one of the
following to turn the speakerphone
on or off:
●
Tap Speakerphone On
to turn the speakerphone on. Tap
Speakerphone Off
to
turn the speakerphone off.
●
Tap Options
in the Options
taskbar, then tap Turn
Speakerphone On or Turn
Speakerphone Off.
NOTE The speakerphone icon
appears in the Notifications and
Status Icon taskbar when the
speakerphone is on.
WARNING! To avoid damage to your
hearing, do not hold the
phone against your ear when
the speakerphone is on.
JS750 39
Using Phone Features
To mute the microphone during a
call
View Call history from the
Notifications and Status Icon taskbar
Tap Mute
to turn the
microphone off and tap Unmute
to turn on.
1. Tap the Notifications taskbar,
then tap the missed call icon
in the drop-down taskbar to
display all missed calls.
To create Notes while in a call
Tap Note
2. Tap Options
in the Options
taskbar, then tap Filter.
To end a call
3. Tap All Calls.
When a call is in progress, tap End
or press the End Key
4. Swipe or flick to scroll through
the list, then tap an entry to view
call details.
2.3 Using Call History
Received call
View call history in the Phone panel.
1. Press the SEND Key
tap Call History
, then
Dialed call
NOTE You can also tap Options
in the Options taskbar, tap View,
then tap All Calls to view your
recent call history.
2. Swipe or flick to scroll through
the list, then tap an entry to view
call details.
3. Tap the entry to call it, or press
the End Key
to exit.
40 JS750
Missed call
5. Tap the entry to call it, or press
the End Key
to exit.
2.4 Speed Dial
NOTES • Number “0” and “1” keys are
reserved and cannot be
assigned as speed dial keys. The
number “1” key is reserved for
voicemail. You can set any
number between “2” and “99”
as a speed dial key.
• If you attempt to assign a speed
dial that is already assigned, you
will be asked if you want to
replace the existing one.
Use Speed Dial to call frequentlyused numbers with a single touch.
For example, if you assign a contact
to location 2 in Speed Dial, you can
touch and hold the number 2 key
on the Phone panel keypad to dial
the contact’s number.
To create a Speed Dial entry
1. Open your Contacts list.
2. Find and tap the desired Contact.
3. Tap Options
in the Options
taskbar, then tap Add to Speed
Dial.
4. Tap the Location field and tap
the Speed Dial location.
5. To save, tap
OK
To delete a Speed Dial
1. Open your Contacts list.
To make a call using Speed Dial
To call any assigned speed dial key,
press the SEND Key
to display
the Phone panel, then
●
Touch and hold the assigned key,
to automatically dial a singledigit speed dial number.
●
To dial a two-digit Speed Dial,
tap the first number key, then
touch and hold the second
number key.
2. Find and tap the desired Contact.
2.5 Making Three-way
Calls
3. Tap Options
in the Options
taskbar, then tap Edit Speed
Dial.
To set up a three-way call, directly
dial the participants and add each
connected call to the three-way call.
4. Tap Trash
and tap Yes.
JS750 41
Using Phone Features
Starting a three-way call
1. Press the SEND Key
open the Phone panel.
to
2. Make the call to the first person.
3. After the first call is connected,
tap Dialpad
, dial the other
number and press the SEND Key
2.6 Using the JS750 as a
GSM Phone
Your wireless phone is set to Global
Mode by default enabling you to
roam internationally on GSM
networks.
You can manually change the phone
to GSM/UMTS Mode.
GSM international roaming
Your phone can operate in a
number of countries on GSM
(Global Systems for Mobile)
networks. Use your phone in
GSM/UMTS Mode or Global Mode
while in countries serviced by GSM
networks.
Ending the three-way call
Tap End
Key
42 JS750
or press the End
Using the GSM SIM card
Your wireless phone comes with a
SIM card preinstalled which, along
with a Global feature on your
account, enables you to make calls
and access email in GSM networks
while traveling overseas. Should
your SIM card be lost or damaged,
please follow these instructions for
the installation of your new SIM.
To remove the SIM card
1. Remove the back cover and the
battery if it is installed. See
Chapter 1 for details.
2. Locate the SIM card slot.
3. Slide the SIM card out from the
slot with your finger.
To install the SIM card
1. Remove the back cover and the
battery if it is installed. See
Chapter 1 for details.
2. Locate the SIM card slot, then
insert the SIM card with its gold
contacts facing down and its
angled corner facing out the card
slot.
3. Slide the SIM card completely
into the slot.
TIP
Any contacts on the SIM card are
automatically added to Contacts.
JS750 43
If you do not want to enter the PIN
to turn on the phone, you can
disable it.
1. Press the Start Key
tap Settings
2. Tap Personal
Phone
2.7 GSM settings
To protect your SIM card with a
PIN code
The preinstalled SIM card may be
locked with a PIN. If you choose to
protect your SIM card with a PIN
code, the PIN will be required each
time the phone is powered on.
When prompted, enter the PIN,
then tap Enter.
, then
, then tap
3. In the banner at the top of the
screen, flick horizontally to
display the Security tab.
NOTE You must be in GSM/UMTS
Mode to access GSM/UMTS
services.
4. Tap the checkbox Require PIN
when phone is used to clear it.
TIPS
• To change the PIN, tap Change
PIN, then enter the PIN you
want to use. Tap Change PIN 2,
then re-enter your PIN to verify
it.
• Emergency calls can be placed
at any time, without requiring a
PIN.
44 JS750
2.8 Turning the Phone
Function On and Off
In many countries, you are required
by law to turn off the phone while
on board an aircraft, or in areas
sensitive to RF transmissions.
To enable or disable the phone
function
1. Press the Start Key
tap Settings
, then
2. Tap Connections
Wireless Manager
, then tap
3. Tap the item(s) to enable or
disable.
●
Tap All
disable all wireless functions.
to
●
Tap Wi-Fi, Bluetooth, or Phone
to disable individually.
JS750 45
Chapter 3 Using the Today Screen
3.1 What’s on the Today
Screen
The Today Screen of your phone
allows quick access to your most
frequently used information and
functions you want to keep at hand.
The Today Screen is organized into
three sections: Notifications and
Status Icons taskbar, Today Screen,
and Options taskbar.
Notifications and Status Icons taskbar
(see page 27 for details)
Today
Screen
3.2 Today Screen
The Today Screen portion of the
screen is organized as panels of
information and programs. It
provides you with current
information, easy swipe viewing, and
quick tap access. Some of the
panels provide at-a-glance
notification by displaying indicators
to alert you to pending information
(e.g., message2 alerts you that two
new messages are pending).
Default Today Screen
The default for Today Screen
includes: pictures, music, phone,
favorite contacts, (visual*)voicemail,
clock, getting started, message, email, calendar and favorites. You can
disable the Windows Default setting
and choose from selected panels to
display instead.
*After subscribing to Visual
Voicemail, the option name on the
Today Screen will change to Visual
Voicemail.
Options taskbar
(see page 28 for details)
46 JS750
Using the Today Screen
Changing Screen background
Tap a Today Screen panel to select
it. The select bar surrounds it and
displays current detail information.
For panels with multiple items (e.g.,
multiple calendar events), swipe
horizontally to scroll through them,
then tap again to open the item.
Set the Today Screen and Start
screen background to suit your
personality.
TIP
Double-tap a Today Screen panel
to open it directly.
1. Press the Start Key
tap Settings
2. Tap Home
, then
3. In the Appearance tab, choose
the background:
Changing the Today Screen
●
Tap a theme from the list, or
Panel items from the Today Screen
are set by default, but you can
choose to display other selected
items instead, then set their order
and set customized options.
●
Tap the Use this picture as
the background checkbox,
then tap Browse to set a
Background image from your
Pictures.
1. Press the Start Key
tap Settings
, then
, then tap Items in
2. Tap Home
the Home Settings tabs at the
top of the screen.
3. Tap the checkbox next to the
item(s) you want as your Today
Screen (all Windows Default
items will be deactivated).
JS750 47
Using the Today Screen
3.3 Teléfono
Your JS750 phone has many calling
capabilities, including Speed Dialing,
emergency calls, international calls
(see page 38), and Smart Dial (see
page 36) as well as many ways to
access the phone's dialpad,
including:
●
Press the SEND Key
●
Double-tap phone from the
Today Screen.
●
Press the Start Key
tap Phone
, then
3.4 Texto
The Message panel contains your
messages (text, picture and video)
all in one place.
Changing the message
account settings
Message Settings
To access Settings for Messaging,
press the Start Key
, tap
Message
, then tap Settings.
There are four message settings
tabs: General Settings, MMS
Settings, SMS Settings and About.
Text Messages
Send text messages (SMS) to other
mobile phones. If your message is
more than 160 characters, it will be
sent as two or more separate
messages and will be billed
accordingly.
Composing and sending text
messages
To access the Message panel:
●
●
Double-tap message from the
Today Screen.
To compose and send a text
message
OR
1. Double-tap message from the
Today Screen, then tap New .
Press the Start Key
tap Message
, then
NOTE If you have unread messages, tap
text, swipe horizontally past
pending messages (No New
Messages is displayed), then tap
the Message panel again.
48 JS750
2. Tap Text message.
Managing text messages
3. Tap the To: box to enter the
mobile phone number of one or
more recipients. There are
additional ways to add contacts:
●
Tap Contact
, tap a contact,
then tap Done .
●
Tap Message
, tap a
message, then tap Done .
●
Tap Call History
then tap Done .
●
, tap a call,
To delete a recipient, tap
the right of the entry.
1. In the Message Inbox, tap a
message to open it.
2. At the bottom of the screen, tap
Reply , tap the text area to
enter your message, then tap
Done , and then Send .
To delete a message
1. In the Message Inbox, scroll up
or down and touch a message
that you want to delete.
Tap Dialpad
tap keys to
manually enter a destination,
then tap Done .
TIP
To reply to a text message
2. Tap
to
Menu
, then tap Delete.
To reply to a text message with an
MMS message
4. Tap the text area to compose
your message. Begin tapping the
displayed keys to enter your text,
then tap Done to exit text
entry.
1. In the Message Inbox, tap a
message to open it.
5. When finished, tap
2. Tap
TIP
Send
To cancel the text message, tap
Menu , then tap Cancel
Message.
You are able to easily reply to a text
message with an MMS message.
3. Tap
Reply
Menu
, tap
Send via Picture Message
JS750 49
Using the Today Screen
MMS
NOTE Make sure the size of the MMS is
Creating and sending MMS
(Multimedia Message Service)
messages to your friends and family
is fun and easy.
NOTES Your phone is already
preconfigured with your wireless
service provider's MMS settings.
MMS is a charged service and
must be provisioned with your
mobile phone plan. Contact your
wireless service provider to have
MMS provisioned as part of your
call plan.
To configure MMS settings
1. Press the Start Key
Message
, then tap Settings.
2. Tap MMS Settings.
3. Configure as necessary and tap
OK to save.
Creating and sending MMS
messages
You can compose MMS messages
with various slides, where each slide
can consist of a photo, audio,
and/or video files.
50 JS750
within the limits of the wireless
service provider while sending it
to another mobile phone user or
to an e-mail address.
1. Press the Start Key
, tap
Message
and tap New
Message.
2. Tap Picture Message or Video
Message.
3. Tap the To: field to enter the
recipient's phone number or email address (or use Contact
, Sent Message History
, Call History
or the
) then tap Done .
4. Tap Subject box, tap keys to
enter a subject for your message,
then tap Done ,
5. Tap Photo
(or Video
),
then tap the photo (or video
clip) you want to send.
OR
Tap Menu , tap Insert, tap
Picture (or Video), then tap the
desired item type.
NOTE To take a new photo, tap
(or
tap Menu , tap Capture, tap
Image). To record a new video,
tap
(or tap Menu , tap
Capture, tap Video).
You can also insert an audio clip
into a picture message. To insert
an existing clip, tap Menu , tap
Insert, tap Audio, then tap the
clip you want. To record a new
clip instead, tap Microphone
, tap Record
, say the
recording, then tap Stop
Viewing and replying to MMS
messages
To view an MMS message
In the Message Inbox, MMS
messages are identified by the MMS
icon
To reply to an MMS message
1. In the Message inbox, find the
message you want to reply to.
6. Tap the text message area to
enter text. To insert My Text
phrases, tap
, then tap the
one you want. To insert
Emoticons, tap
, then tap
the one you want.
2. While still in the Inbox, touch and
hold the message.
7. Tap
Done
4. Complete the message as
necessary.
8. Tap
Send
NOTES • To designate recipient(s) as
addressee, copied addressee, or
blindcopy addressee, tap the
To: box, the To: box again
then tap To, Cc or Bcc as
needed.
• To remove a photo, text, or
audio, tap
next to the item
to remove.
• Additional slides are added
automatically if you insert
multiple photos into the
message.
3. Once the popup menu appears,
tap Reply , then tap the type of
message.
3.5 E-mail
Setting Up E-mail Accounts
Before you can send and receive email, you need to set up your e-mail
account on your phone. You can set
up the following types of e-mail
accounts on your phone:
●
Outlook e-mail that you sync
with your computer or the
Exchange Server.
JS750 51
Using the Today Screen
●
E-mail account that you have
from an Internet Service Provider
(ISP) or other e-mail provider.
●
Web-based e-mail accounts such
as Yahoo!® Mail Plus or AOL®.
●
Custom domain e-mail accounts.
The e-mail domain name is
hosted by a different e-mail
provider.
●
Work account that you access
using a VPN connection.
Synchronizing Outlook e-mail
with your computer
If you've installed the
synchronization software on your
PC and created a partnership with
your phone, then your phone is
ready to send and receive Outlook
e-mail. If you have not yet installed
the synchronization software or
created a partnership, follow the
procedures in page 121.
TIP
To set up your company e-mail
account so that you can access
Outlook e-mail messages
wirelessly, you must set up your
phone to synchronize via an overthe-air connection with your
company’s Exchange Server. For
more information about
synchronizing with your company
e-mail server, see Chapter 7.
52 JS750
Setting up an Internet e-mail
account
Set up a POP3 or IMAP4 e-mail
account on your phone if you have
an e-mail account from an Internet
service provider (ISP), or a Webbased account such as Yahoo! Mail
Plus, etc. You can also add a work
account that you access using a
VPN server connection as a
POP3/IMAP4 account.
1. Press the Start Key
, tap Email
, then tap Setup E-mail.
2. Enter the E-mail address and
Password for the e-mail account
and tap the checkbox Save
password then tap Next.
3. Tap Next.
NOTE E-mail Setup searches your phone
for preloaded e-mail configuration
settings. If the phone cannot find
the server settings for the
specified e-mail account, your
phone needs to connect to the
Internet and try to download the
settings. If it cannot find the
settings online, you need to enter
the settings manually.
4. Enter your name and the
Account display name, then tap
Next.
5. If prompted, choose how often
you want e-mail messages to be
automatically sent and
downloaded on your phone.
●
Select the checkbox Outgoing
server requires authentication if
required by your provider.
●
If the outgoing e-mail server
requires a different user name
and password for sending e-mail,
clear the checkbox Use the same
user name and password for
sending e-mail. You will then be
prompted to enter this
information.
●
Tap Advanced Server Settings,
then select the checkbox Require
SSL if your e-mail provider uses
an SSL connection for more
secured e-mail.
●
From the Network connection
list, select the data connection
that you use for connecting to
the Internet.
NOTE Tap Review all download settings
to select download options, set
the e-mail format as HTML or
plain text, and more. For more
information, see “To customize
download and format settings.“
6. Tap Finish.
To specify e-mail server settings
If Auto Setup is unsuccessful,
contact your ISP or e-mail provider
for the incoming mail server and
outgoing mail server settings so you
can enter them on your phone.
Other options that you can select
include the following:
To customize download and
format settings
Before you tap Finish when setting
up your Internet e-mail account,
you can tap Review all download
settings to choose download
options, message format, and other
settings. Tap Advanced Settings for
further options.
JS750 53
Using the Today Screen
Options
Description
Automatic
Send/Receive
You can select a time interval for
connecting to the Internet
automatically to send and receive
messages.
Download
messages
Set the number of days of messages
that you want to be downloaded to
your phone.
Send/receive
when I click
Send
By default, messages are
immediately delivered when you tap
Send. If you prefer to save outgoing
messages to the Outbox folder first,
clear the check box. (In this case,
you will need to manually send
messages by tapping Menu, then
tap Send/Receive).
Use automatic
send/receive
schedule when
roaming
This allows your phone to data roam
when there is a set time interval for
connecting to the Internet
automatically. Since this may result
in higher connection costs, you may
want to leave the check box cleared.
When deleting
messages
Choose whether to delete messages
from the mail server when you delete
them on your phone.
Message format
Select HTML or Plain Text.
Message
download limit
Select the e-mail download size. If
you have large volumes of e-mail,
use a lower size or select to
download headers only.
Download
attachments
Set your preference when there is an
e-mail attachment
Setting up a custom domain
e-mail
When you are using an e-mail
domain name that is hosted by a
different e-mail provider (for
example, your e-mail address may
be johndoe@work.com but Email.com hosts the e-mail account
and provides e-mail services), select
the Custom Domain option in the
E-mail Setup wizard to set up your
e-mail account on your phone.
, tap
1. Press the Start Key
E-mail
, then tap Setup
E-mail.
2. Enter your E-mail address and
the Password for your e-mail
account and select the checkbox
Save password. Tap Next.
3. Clear the checkbox Try to get email settings automatically from
the Internet, then tap Next.
4. In your e-mail provider, select
Custom domain then tap Next.
5. Enter the domain of your e-mail
provider, then tap Next.
54 JS750
6. The E-mail Setup wizard then
tries to find the e-mail provider
settings on your phone or from
the Internet. If the settings are
found, it shows a successful
message. Tap Next.
Creating and sending e-mail
messages
7. Enter your name and the
Account display name, then tap
Next.
To compose and send an e-mail
NOTE If the E-mail Setup wizard was
unsuccessful in finding the
settings, you will be prompted to
enter e-mail server settings on the
succeeding screens. See “To
specify e-mail server settings” for
details.
8. In the Automatic Send/Receive
list, choose how often you want
e-mail messages to be
automatically sent and
downloaded on your phone.
NOTE Tap Review all download settings
to select download options, set
the e-mail format as HTML or
plain text, and more. For more
information, see “To customize
download and format settings."
9. Tap Finish.
After setting up e-mail accounts on
your phone, you can start sending
and receiving e-mail messages.
1. Double-tap e-mail from the
Today Screen, then tap the email
account to use.
2. Tap
Menu
, then tap New.
3. Enter the e-mail address(es) (put
semicolon between addresses).
To copy address(es) from your
phone's memory, with the cursor
in the To: box, tap Menu , tap
Add recipient, then tap the
contact.
4. Enter a subject and compose
your message. To quickly add
common phrases, tap Menu , tap
My Text, then tap the phrase to
insert.
5. Tap
TIPS
Send
• To change message options, tap
Menu , then tap Message
Options to set priority, security,
permission, and language.
JS750 55
Using the Today Screen
• If you are working offline, e-mail
messages are moved to the
Outbox folder and will be sent
the next time you connect.
To add an attachment to an e-mail
1. In the message that you are
composing, tap Menu , tap
Insert, then tap the items to
attach: Picture, Voice Note, or
File.
2. Tap the file you want to attach,
or record a voice note, then
complete the message as
necessary.
Searching e-mail messages
To search the Inbox message list
Filter the e-mail messages in your
Inbox to only display the e-mail
messages that contain the sender
or e-mail subject you are searching
for. Use touch keys or keyboard to
enter the characters or numbers for
your filter search. As you enter, the
list narrows down to the conditions
you set.
56 JS750
For example, tap (or press) “J” then
"A" to narrow the list to only the email messages that contain sender
names and e-mail subjects that start
with “JA.”
To download a complete e-mail
By default, each e-mail in the inbox
on your phone contains only the
first few kilobytes of the message.
When you open an e-mail, it
displays only the headers and part
of the message. You must download
the whole e-mail to view the
complete content.
To download a complete e-mail
message, open the e-mail and then
do one of the following:
●
Scroll down to the end of the
message and tap Get the rest of
this message.
●
Tap Menu , then tap Download
Message.
NOTE The Fetch Mail feature, which is
available for POP3 and IMAP4
Internet e-mail accounts,
downloads an entire e-mail
without the need for you to
perform a full synchronization.
This limits the download to just
the e-mail message(s) that you
want and helps save data costs.
Fetch Mail is also available for
Outlook E-mail. See “Instant
download through Fetch Mail” in
page 137.
To use shortcuts
When in an e-mail account, press
and then touch and hold to open a
shortcut list of often-used
commands. Touch and hold the
shortcut key to execute the
command.
To download an attachment
In an open message with an
attachment to download, tap the
attachment. If there is more than
one attachment, tap the other
attachments to download them. You
can directly open the file in the
associated program after download
by tapping the attachment again.
To reply to or forward an e-mail
1. Open the message, tap Menu ,
tap Reply/Forward, then tap
Reply, Reply All, or Forward.
2. Enter your response (also enter
the address(es) if you are
forwarding the message), then
tap Send .
NOTE You can receive and view HTML
e-mail messages from any type of
e-mail account. The HTML format
is retained, without layout shifting
or resizing. HTML e-mail support
in Outlook Mobile is available
only if you are synchronizing your
phone with a Microsoft Exchange
Server.
Synchronizing e-mail
messages
Synchronizing e-mail messages
ensures that new e-mail messages
are downloaded to the phone Inbox
folder, e-mail messages in the
Outbox folder are sent, and e-mail
messages deleted from the server
are removed from your phone. The
manner in which you synchronize
e-mail messages depends on your
e-mail account type.
JS750 57
Using the Today Screen
To automatically synchronize an
Outlook e-mail account
1. Connect your phone to your
computer through USB or
Bluetooth. Otherwise, connect
through Wi-Fi or a data
connection if you are
synchronizing Outlook e-mail
with the Exchange Server. For
more information, see Chapter 7.
2. Synchronization automatically
begins, and your phone send.s
and receives Outlook e-mail.
To manually synchronize your
Outlook or Internet e-mail
account
1. Double-tap e-mail from the
Today Screen, then select your email account.
2. Tap Menu , then tap
Send/Receive.
Customizing e-mail settings
To change the download size and
format for Outlook e-mail
1. Disconnect your phone from the
computer.
, scroll
2. Press the Start Key
the screen up, then tap
ActiveSync
3. Tap Menu , tap Options, tap
E-mail, then tap Settings.
4. On the E-mail Sync Settings
screen, set the Download size
limit and Message format.
5. Tap
OK
To change the download size and
format for POP3/IMAP4 e-mail
1. While viewing POP3/IMAP4 email Account, tap Menu , tap
Options, tap the account to
modify, then tap Download size
settings.
2. On the E-mail Setup, set the
Message format, Message
download limit and Download
attachments,
3. Tap
58 JS750
Done
3.6 Contactos
Contacts is your address book and
information storage for the people
and businesses you communicate
with. If you use Outlook on your
PC, you can synchronize contacts
between your phone and PC.
Creating a contact
1. From the Today Screen, tap
Contacts , tap New
, then tap
Outlook Contact.
NOTE To create a new contact on your
SIM card (if one is installed), tap
SIM Contact. You can also use
SIM Manager to add contacts to
your SIM card. For more
information about SIM Manager,
see “SIM Manager” in this chapter.
4. To assign a picture to a contact,
tap the Communicate tab at the
top of the screen, tap the Picture
box
, tap the picture to set,
then tap OK .
TIPS • If someone calls who is not in
your list of contacts, you can
quickly add it to Contacts from
the phone's call history. Tap the
call entry, tap Option
, tap
Save to Contacts, tap New
Contact, then enter the
necessary remaining information.
• If someone who is not in your list
of contacts sends you a message,
tap the message, tap Menu , tap
Contact Details, tap Menu , tap
Save As New Contact, then enter
the necessary remaining
information.
2. Tap a field to select it, then enter
contact details as necessary.
Contact information is contained
in three tabs. Communicate, Info,
and Notes. Tap these tabs to
complete the entry as necessary.
3. To easily identify the caller, you
can assign a custom ring tone to
each Outlook contact. To assign
a custom ring tone, tap the Info
tab at the top of the screen, tap
Set Ringtone, tap the ringtone
you want to set, then tap OK .
JS750 59
Using the Today Screen
Editing and calling a contact
Finding a contact
To view and edit a contact
information
To find a contact
1. From the Today Screen, tap
Contacts .
2. Tap the contact whose
information you want to view or
edit.
1. From the Today Screen, tap
Contacts .
2. Do one of the following:
●
Begin entering a name or phone
number of the contact until the
contact is displayed. As soon as
you enter a character, contacts
that begin with that character are
displayed (e.g., entering V could
display Vet, Victor Smith, or Joe
Vick). The next character entry
continues to narrow the search.
●
If you have assigned categories
(e.g., Business) to your Outlook
contacts, you can filter the
Contacts list by category. In the
Contacts list, tap Options
tap Filter, then tap a category. To
show all contacts again, tap All
Contacts.
3. Tap the name field.
4. Tap the field(s) you want to edit.
5. Make changes as needed, then
tap OK .
To call a contact from the
Contacts panel
1. From the Today Screen, tap
Contacts .
2. Tap the contact to call and press
the SEND Key
. The
contact’s default phone number
is dialed.
TIP
To call a phone number other
than the default, tap the contact,
tap the number you want to dial,
and press the SEND Key
60 JS750
●
If you have entered information
under Company for your
Outlook contacts on your phone,
you can quickly locate the
contacts that work for a specific
company. In the Contacts list, tap
Options
, tap View By, then
tap Company. Tap the company
to see the contacts who work
there.
NOTE To return to the previous view, tap
Options
tap Name.
, tap View By, then
Sharing contact information
To beam contact information to
another device via Bluetooth
1. Turn on the Bluetooth
functionality (Start > Settings >
Bluetooth).
2. From the Today Screen, tap
Contacts .
3. Touch and hold the contact until
the popup menu appears.
4. Tap Send via Bluetooth.
5. Tap the device you want to beam
the contact details to and follow
the instructions, as necessary.
NOTE For more information, see
“Bluetooth” in Chapter 8.
To send contact information via a
text message
1. From the Today Screen, tap
Contacts .
2. Touch and hold the contact, tap
Send Contact and tap
Messages. Select the contact
information that you want to
send and tap Done .
3. In the new text message, enter
the mobile phone number of the
person you want to send the
contact information to and tap
Send .
3.7 Visual Voice Mail
Visual Voice Mail allows the
management of voice mail directly
from the device rather than
accessing voice mail via traditional
method(s). Visual Voice Mail
displays a list of messages and
allows the user to choose which
message to listen to or delete,
without having to dial into their
mailbox, listen to voice instructions,
or prior messages.
JS750 61
Using the Today Screen
1. Press the Start Key
tap Visual Voice Mail
, then
2. Follow the instructions to sign in.
3.8 Mobile Email
Mobile Email is an application
already downloaded on your device.
Don't miss an important email.
Thanks to Mobile Email, you can get
your emails on your phone, while
you're on the go. Mobile Email
works with many providers,
including Yahoo!, AOL, and others.
Get alerts from your
JS750 smart phone when new email
has arrived.
Additional fees may apply.
1. Press the Start Key
, then
tap Mobile Email
3.9 Mobile IM
Mobile IM provides you with access
to popular instant messaging (IM)
communities, including AOL® Instant
Messenger (AIM®), Windows Live™
Messenger, and Yahoo!® Messenger.
Instant Messaging enables you to
sign in to multiple communities at
the same time.
62 JS750
1. Press the Start Key
tap Mobile IM
, then
2. Read the disclaimer and tap
Accept.
3. Tap the Mobile IM provider, enter
the required sign-in information
for the selected community, such
as user name or password, then
tap Sign In.
NOTE The information required to sign
in will vary depending on the
instant messaging community you
are accessing.
The instant messaging screen for
your selected community will then
be displayed, and you can start
chatting online with your friends or
family.
For more information on using
Mobile IM, tap Help.
NOTE Separate charges apply to
send/receive instant messages.
3.11 Internet Explorer
Navigating web pages
Internet Explorer Mobile is a fullfeatured Internet browser, optimized
for use on your phone.
Viewing and navigating web pages is
easy, even on large sites.
Browsing the Web
1. Press the Start Key
, then
tap Internet Explorer
2. Tap the web address bar, enter
the URL/address, then tap
While browsing the Web, tap Menu
, then tap Browser menu
to
access the browser's options.
1. Go to the web page that you
want to view.
2. Use your fingertip or stylus which
is attached on the back side of
the device to easily drag page
contents into view anywhere on
the web page.
3. Tap Menu
to display the
zoom bar at the right side of the
LCD and full menu bar along the
bottom.
4. Touch and slide the zoom indicator
up or down the zoom bar, or tap
any of the menu bar icons.
Copying web page text
Copy text from a web page and
then paste it on a text message or
e-mail.
To copy text on a web page
1. On the web page, tap Menu
tap Browser menu
, then tap
Copy/Paste.
JS750 63
Using the Today Screen
2. Tap Make Selection, then use
your fingertip, or stylus which is
attached on the back side of the
device, to touch and drag over
the text you wish to copy.
3. Tap
Copy
3.12 Configuración
Enjoy the freedom of customizing
your JS750 to operate according to
your own preferences using the
Settings menus. Within Settings on
the Start screen, there are several
Settings menus. The submenus and
options in some of the Settings
menus are organized into tabs. Tabs
are displayed at the top of the
screen allowing you to easily tap to
view and change settings as needed.
Access Settings
1. Press the Start Key
, tap
Settings
, then tap the
Settings menu you want to view.
TIP
Settings options are often
organized into separate tabs. Use
the Tab Bar (as shown in the
following image) to access all
options.
64 JS750
Tab Bar
Settings and
choices
Options
taskbar
Settings Menus and Tabs Overview
Clock & Alarms Menu for
setting time and alarms.
Alarms tab: View or set alarms.
Time tab: View or change time
and date settings.
Home Sets Today Screen
display.
Appearance tab: Sets
background theme for LCD.
Items tab: Sets items
displayed on Today Screen.
Lock Use to secure your
phone.
Password tab: Sets your
password.
Gesture Unlock tab: Allows
you to use gestures to unlock
screen and launch program.
Wi-Fi
Wireless tab: Use to select or
add a Wi-Fi connection.
Network Adapters tab: Sets
network connection adapters.
Wireless Manager
Sounds and Notifications
Sets your alerts.
Sounds tab: Enables sounds.
Notifications tab: Sets ring
type and ring tone for
selected events.
Vibrations tab: Sets screen
vibration.
Program Buttons tab: Changes
functions for selected keys.
Connections settings Use for
connection(s) setup.
Up Down Control tab: Sets
Volume Key sensitivity.
Connections
Tasks tab: Sets modem, VPN
server and proxy server.
Advanced tab: Sets network
selection, dialing rules and
exceptions.
Domain Enroll
GPRS Setting
Switch USB
USB to PC
Personal settings Use to set
your phone functionality
preferences.
Buttons
Owner Information
Identification tab: Your
identifying information.
Notes tab: Free-form text area.
Phone
Sounds tab: Sets default ring
type and tone, keypad tone,
voicemail access, and voice
privacy alert.
Security tab: Sets PIN security
(password required to power up).
JS750 65
Using the Today Screen
GSM Services tab: Sets provider
services such as Call Barring,
Caller ID, Call Forwarding, Call
Waiting, Voicemail and Text
Messages, and more.
Network tab: Let's you select the
network and mode of operation.
Voice Commands
System settings
Use for system configuration.
About
Version tab: View device version
information.
Device ID tab: Enter your device
identification (used to identify it
to other devices).
Copyrights tab: View copyright
text.
Backlight
Battery power tab: Sets
backlight duration when running
on battery power.
External power tab: Sets
backlight duration when fed from
external power.
Button tab: Sets backlight
duration for the key backlights
66 JS750
presses.
Brightness tab: Lets you set the
brightness or enable the
Luminous sensor.
Certificates
Personal tab: Select and view
personal authority certificates.
Intermediate tab: Select and
view intermediate authority
certificates.
Root tab: Select and view root
authority certificates.
Customer Feedback
Encryption
Error Reporting
External GPS
Programs tab: Lets you set the
port for GPS data.
Hardware tab: Lets you set the
hardware port and baud rate.
Access tab: Lets you enable the
GPS access management.
Managed Programs
Memory
Main tab: View storage and
program memory (used and free
space).
Storage Card tab: View card
memory.
Clear Storage tab: Allows you to
erase all data and resets to the
factory defaults.
Power
Battery tab: View battery type
and status.
Advanced tab: Lets you set the
timeout for sleep mode on
battery or external power.
Regional Settings
Region tab: Lets you set region
and displays regional information.
Number tab: Lets you set
number formats.
Currency tab: Lets you set
currency formats.
Screen
Alignment tab: Lets you calibrate
the screen.
Clear Type tab: Lets you set
clearer fonts.
Text Size tab: Lets you set text
size.
Sensor
Accelerometer tab: Lets you set
automatic screen rotation (left
and right handed).
Luminous tab: Enables the
luminosity sensor.
Proximity tab: Enables the sensor
to lock the touch screen when
the device is held to your ear.
System Information
Version tab: View OS, ROM date,
hardware, software, PRL, and ERI.
Time tab: Lets you set time
formats.
Date tab: Lets you set date
formats.
Remove Programs
JS750 67
Using the Today Screen
Product tab: View product,
manufacturer, language, model ID
and processor.
2. On the Alarms tab, tap any of
the alarms to display Alarm
Settings for that alarm.
Owner tab: View owner
information.
3. Tap the time, then tap arrows
to set the alarm time.
Phone Info tab: View, MDN, IMEI,
MCCID MNCID, warranty code
date, SIM ICCID
4. Tap the description box, then
enter a description for the alarm.
Task Manager
5. Tap the day(s) of the week for
the alarm to sound.
Microsoft My Phone
TIP
Bluetooth
6. Tap Arrow in the Sound box,
then tap the sound to be played
at the alarm time.
Lock Key
3.12.1 Reloj y alarmas
You can set up to three alarms.
, tap
1. Press the Start Key
Settings
, then tap Clock &
Alarms
to open the Clock &
Alarms.
SHORTCUT Tap
from the Today
Screen for quick access to
Clock & Alarms.
NOTE Your alarms will not be audible if
your phone is set to silent or
vibrate.
68 JS750
You are able to select any days of
the week for your alarm.
7. Tap Arrow in the notification
type box, then tap how to play
the alarm alert.
Play once/ Repeat/ Repeat and
Vibrate/ Vibrate only
8. Tap OK when settings are
completed.
[Alarm Settings]
To set time
Tap Time in the tab bar at the top
of the screen to move to the Time
tab, then adjust the settings for
time zone, date or time.
Touch
OK
to save settings.
To activate and deactivate
alarm(s)
If you want to disable an alarm,
simply turn it off by tapping the
checkbox next to it. The X is
removed, but the settings remain
allowing you to simply tap the
checkbox to reactivate later.
[Time]
Dismissing an alarm
When an alarm goes off, you can
choose to Snooze or Dismiss the
alarm. When you select Snooze
the alarm will sound again
after five minutes.
JS750 69
Using the Today Screen
2. On the Password tab, tap the
checkbox Prompt if device
unused for, then tap Arrow
and tap the amount of time
before a password is required.
3.12.2 Incio
Home settings allow you to set the
appearance of your Today Screen.
1. Press the Start Key
, tap
Settings
, then tap Home
2. On the Appearance tab, tap the
theme to set as the background
screen.
3. Tap the Items tab to select items
displayed from the Today Screen
and set the timeout for the
Today Screen.
4. Tap
OK
3. Tap the arrow
in the
Password type box, then tap
Simple PIN or Strong
alphanumeric.
4. Enter the PIN or alphanumeric
password and then enter it again
to confirm.
TIP
3.12.3 Blouear
If your device is configured to
connect to a network, use a
strong password to help protect
network security.
Protect your phone from
unauthorized use by assigning
password(s) to gain access.
4. Tap OK . The next time you unlock
your device, you will be prompted
to enter your password.
To Protect your Phone
To Change your Password
Protect your phone from
unauthorized use by assigning a
type of password or a PIN (personal
identification number).
1. Press the Start Key
, tap
Settings
, then tap Lock
You will be prompted to enter
your current password, then reenter it in the Confirm box.
1. Press the Start Key
, tap
Settings
, tap Lock
2. Tap the Password box, enter your
new password.
4. Tap
70 JS750
OK
3.12.4 Sonidos y notificaciones
3.12.5 Conexiones
To Set Sounds & Notifications of
Actions
The Connections Settings menu has
additional sub-menus which provide
you with control over how your
phone uniquely connects to
network(s) and other devices.
1. Press the Start Key
, tap
Settings
, then tap Sounds &
Notifications
2. On the Sounds tab, tap the
checkbox(es) to enable sounds
as you want.
3. Tap the Notifications tab, to
select notification event(s) and
corresponding ring type and tone
to alert you. Tap
next to
Event and tap an event, tap
next to Ring type and tap the
type you want, then tap
next
to Ring tone and tap the tone
you want.
1. Press the Start Key
, tap
Settings
, then tap
Connections
2. Tap a Connections sub-menu.
Connections Tap to set up
network server connections. It has a
Tasks tab and Advanced tab.
●
The Tasks tab has (settings
cannot be modified) and My
Work Network connections. Tap
Add a new modem connection,
Add a new VPN server
connection or Set up my proxy
server and enter information as
necessary.
●
The Advanced tab allows you to
set which networks are
automatically used (tap Select
Networks) as well as create rules
(tap Dialing Rules) and URL
exceptions for intranet (tap
Exceptions).
4. Tap the Vibrations tab, tap the
checkbox to enable vibrations for
screen taps, then tap the
vibration type.
5. Tap
OK
when finished.
JS750 71
Using the Today Screen
Domain Enroll Tap to connect
your phone with company
resources. Tap Enroll and enter
information as necessary.
●
USB Mass Storage allows your
PC to use your phone as an
external drive.
GPRS Setting Tap to select the
GPRS authentication method. Tap
None, PAP Authentication or CHAP
Authentication.
To set your USB default connection
preference, press the Start Key
> Settings
> Connections
> Switch USB
Be sure to press Save to save
your preferences.
Switch USB Tap to select USB
access during a USB connection.
Tap ActiveSync, VZAccess
Manager, or USB Mass Storage.
USB to PC Tap to change the
advanced network functionality. Tap
the checkbox to enable or disable.
The JS750 can connect with and
charge through your PC with
ActiveSync, VZAccess Manager, or
USB Mass Storage.
●
●
When set to ActiveSync, the
phone will automatically sync
with your PC via ActiveSync.
ActiveSync must be installed on
your PC before using this
connection mode.
VZAccess Manager configures
your PC to use your wireless
phone as a modem. VZAccess
Manager must be installed on
your PC before using this
connection mode.
72 JS750
Wi-Fi Tap to select or add WiFi connection. It has a Wireless tab
and Network Adapters tab.
●
The Wireless tab allows you to
select or add a router.
●
The Network Adapters tab
allows you set and enter network
connection adapters.
Wireless Manager Tap to
manage your RF transmissions. You
can disable (and enable) all RF
functionality by tapping All
, or disable/
enable selectively by tapping Wi-Fi,
Bluetooth, or Phone.
3.12.6 Personal
The Personal Settings menu has four
additional sub-menus which provide
you with control over how your
phone alerts you, usage, services,
and identification to other devices.
1. Press the Start Key
, tap
Settings
, then tap Personal
2. Tap a Personal sub-menu.
Buttons Tap to set
functionality for specific hardware
keys. It has a Program Buttons tab
and Up/Down Control tab.
The Program Buttons tab has a
box to select the button and a
box to select the program it will
access. Tap available selections in
the boxes to set to your
preferences.
●
The Up/Down Control tab allows
you to customize the Volume Keys
reaction. Touch and drag across
the slide bar for Delay before
first repeat between Short and
Long, and for Repeat rate
between Slow and Fast.
Owner Information Tap to enter
your infomation and notes. It has an
Identification tab and Notes tab.
●
The Identification tab has boxes
to enter name, company, address
telephone, and email.
●
The Notes tab is a free-form text
area.
Phone Tap to customize
settings to define how you use your
phone. It has a Sounds tab, Security
tab, GSM Services tab, Network tab,
and Band tab.
●
The Sounds tab displays your
phone number, sound settings
and voicemail access number.
Ring type
Tap how you want to be notified
of incoming calls.
Ring / Increasing ring / Ring
once / Vibrate / Vibrate and ring
/ Vibrate then ring / None
Ring tone
Tap a ringtone in the list.
Keypad
Tap the tone length heard when
touch keys are tapped.
Long tones / Short tones / Off
JS750 73
Using the Today Screen
●
The Security tab activates PIN
security features.
●
The GSM Services tab displays
available access services. Tap a
service in the list from your
service provider, then tap Get
Settings.
Call Waiting
Notify me: Alerts you to waiting
calls.
Voice Mail and Text Messages
The SIM card in your phone
automatically sets your voice mail
and SMS servers by default.
Open to view settings.
Call Barring (emergency calls
excluded)
Block incoming calls: Off / All
calls / When roaming
NOTE
Block outgoing calls:
Off / All calls / International /
International except to home
country
NOTE
Everyone: Displays your caller ID
No one: Hides your caller ID
Only to contacts: Displays your
caller ID for Contacts calls only
Call Forwarding
Forwards calls to another number.
74 JS750
Fixed Dialing
Select Fixed Dial numbers to turn
on and compile a list of numbers
that can be called from your
phone. When activated, only
numbers included in the fixed dial
list can be called from your
phone.
Call Barring is a network
subscription service. Upon
subscription, your service
provider will give you the
password to edit these
settings.
Caller ID
You can also view your voice
mail number on the Speed
Dial screen and in the Phone
settings Sounds tab.
●
The Network tab displays the
current network, mode of
operation, GSM Network
selection, and preferred
networks.
NOTE The ability to choose between
available networks can be
beneficial when traveling.
Current network
Tap Find Network to find other
available networks.
Alerts
ERI Banner: On / Off
ERI Sound: On / Off
Mode of operation
GSM/UMTS Mode / Global
Mode
Emergency Tone
Alert / Vibrate / Off
GSM network selection
Manual / Automatic
TIP
Manual setting can be useful when
you know that one network is less
expensive than another or that it
provides faster data transmission.
Preferred networks
Tap Set Networks (retrieving
settings may take a few minutes).
Tap a network to select it, then
tap Move Up or Move Down to
reprioritize the order for network
usage.
Answer Options
Any Key / Auto Answer with
handsfree
TTY
Full / Talk / Hear / Off
GPS
Location On / 911 Only
Voice Privacy
On / Off
Assisted Dialing
Enables assisted dialing for
international calls. See page 38
for details.
The Band tab displays frequency
channels used to access service.
GSM/UMTS Settings
GSM Only/ UMTS Only/
GMS/ UMTS Dual
Voice Command Tap to set
voice command functionality. Tap a
voice command setting in the list,
then tap the setting you want.
Confirmation
Automatic / Always Confirm /
Never Confirm
JS750 75
Using the Today Screen
Sensitivity
Most Sensitive / Recommended /
Least Sensitive
●
The Version tab displays
Windows Mobile Professional
information.
Adaptation
Adapt voice to your speech
patterns.
●
The Device ID tab enter device
name and description to identify
your device to other devices.
Prompts
Mode: Prompts/ Readout +
Menu / Readout/ Tones Only
Timeout: 5 seconds/ 10 seconds
●
The Copyrights tab displays
copyright text.
About
Backlight Tap to set
illumination settings on four tabs.
●
The Battery power tab sets the
backlight duration when battery
powered.
●
The External power tab sets the
backlight duration when powered
from an external source.
1. Press the Start Key
, tap
Settings
, then tap System
●
The Button tab sets the
backlight duration when any
hardware key is pressed.
2. Tap a System sub-menu.
●
The Brightness tab sets the
screen brightness manually or
activates the Luminous Sensor.
3.12.7 Sistema
The System Settings has additional
sub-menus which allow you to set
up the phone management
environment.
About Tap to view device
information on three tabs.
Certificates Tap to manage
certification authority on three tabs.
●
76 JS750
The Personal tab displays
personal certificates for positive
identification.
●
The Intermediate tab displays
intermediate certification
authorities.
●
The Root tab displays positive
root certification authorities.
Customer Feedback Tap to
elect to participate in customer
feedback to Microsoft.
Encryption Tap to encrypt files
placed on a storage card for
increased security.
Error Reporting Tap to set the
device to report software operation
errors to Microsoft to diagnose
problems.
External GPS Tap to set GPS
information on three tabs.
●
The Programs tab sets the GPS
program port.
●
The Hardware tab sets the GPS
hardware port.
●
The Access tab sets the device
to manage GPS automatically.
Managed Programs Tap to
view list of installed managed
programs.
Memory Tap to view and
manage memory usage on two tabs.
●
The Main tab displays memory
used for storage and programs.
●
The Storage Card tab displays
memory used and memory free.
●
The Clear Storage tab sets the
phone to reset to factory default
or your custom configuration.
Power Tap to view and manage
power settings on two tabs.
●
The Battery tab displays the
battery status.
●
The Advanced tab sets power
conserving settings.
Regional Settings Tab to set
regional information on five tabs.
The Region tab set region from
the drop-down list.
The Number tab sets your data
numbers format.
The Currency tab sets your data
currency format.
The Time tab sets time format.
The Date tab sets date format.
JS750 77
Using the Today Screen
Remove Programs Tap to
select program(s) to remove from
device memory.
The Product tab displays name,
manufacturer, language, model
ID, and processor.
Screen Tap to set screen
responsiveness and font settings on
three tabs.
The Owner tab displays owner
information.
The Alignment tab calibrates the
screen to your touch.
The ClearType tab sets
ClearType to smooth font edges.
The Text Size tab sets text size.
Sensor Tap to set sensors on
three tabs.
The Accelerometer tab sets
device to automatically rotate
screen contents.
The Luminous tab sets light
sensor.
The Proximity tab sets proximity
sensor.
System Information Tap to
view system information on four
tabs.
The Version tab displays OS,
ROM date, hardware, software,
PRL, and ERI.
78 JS750
The Phone Info tab displays
MDN, IMEI, MCCID MNCID,
Warranty date code, and SIM
ICCID.
Task Manager Tap to manage
your device tasks. Tap an
application, then tap End Task to
end the task. You can also tap Menu
Menu to switch applications, end
all tasks, change view, change sort,
refresh, or exit Task Manager.
Wireless LAN Tap to manage
your wireless LAN on two tabs.
The Main tab displays wireless
LAN information.
The Station tab sets status,
mode, SSID, BSSID, channel,
speed, and signal quality.
3.12.8 Bluetooth
Bluetooth enables compatible
mobile devices, peripherals, and
computers that are in close
proximity to communicate directly
with each other wirelessly. This
handset has built-in Bluetooth
connectivity, which makes it
possible to connect it with
compatible Bluetooth headsets,
computer applications, and so on.
3. There are three tabs for
Bluetooth: My Devices,
Accessories any Settings.
●
Add a device:
Allows you to set up a new
Bluetooth device.
Disable Bluetooth:
Turns off Bluetooth.
Advanced:
Allows you to set up additional
options.
Bluetooth QD ID B016063
NOTE
●
If you use PC Sync via
Bluetooth, you can exchange
data with your PC.
you receive data from
another Bluetooth device, the
phone requests confirmation.
Settings tab
●
My Devices tab
Allows you to see the information
and properties of the paired
devices.
●
Accessories tab
● When
Bluetooth must be turned on to
use these features.
Print Images: Allows you to lay
out and print pictures from your
handset.
1. Press the Start Key
, tap
Settings
, then tap Bluetooth
PC Remote Control: Allows you
to remotely control a PC with
your device.
2. If Bluetooth power is set to off,
you will be prompted to turn
power on. Tap Yes to turn on
Bluetooth.
Business Card Exchange: Allows
you to send and receive business
cards.
●
JS750 79
Using the Today Screen
BT Send Object: Allows you to
send objects such as Outlook Email, Contacts, Tasks, Notes,
Calendar Items, Audio, Ring
Tones, Images, and Videos to a
another Bluetooth device.
To make your phone Bluetooth
visible
1. Press the Start Key
, tap
Settings
, then tap Bluetooth
NOTE If Bluetooth power is off, you will
be prompted to turn power on.
Tap Yes to turn on Bluetooth.
2. Tap Settings in the tab bar at the
top of the screen, then tap Not
Discoverable (which is the
default setting).
3. Tap , then tap the setting you
want. Always Visible/ Visible for
180 seconds/ Never Visible
4. Tap
Done
NOTE To turn off Bluetooth capabilites
on your phone, tap Disable
Bluetooth on the Bluetooth
Settings tab.
80 JS750
TIP
Enter a Bluetooth phone name for
your phone. This will be the
phone name that will be shown on
another Bluetooth-enabled device
when it searches and detects your
phone. To enter a name, on the
Bluetooth screen, tap Security
and enter a device name.
Bluetooth pairing
Pairing is a Bluetooth partnership
relationship that you create
between your phone and another
Bluetooth-enabled device in order
to exchange information in a secure
manner.
To create a Bluetooth pairing
1. Press the Start Key
, tap
Settings
, then tap Bluetooth
2. Tap Yes to turn Bluetooth On,
if it is Off.
3. Tap Add. Your phone searches
for other Bluetooth-enabled
devices and lists them.
4. Select the desired device name in
the list.
5. The handset may automatically
send a passcode to try and
autopair. Once complete, Tap
Done . If the handset does not
autopair, continue on to the next
step.
6. Enter, or confirm, a passcode
(typically “0000”) to establish a
secure connection, then tap OK .
7. Wait for the paired device to
accept the partnership. The
receiving party needs to enter
the same passcode that you
specified.
To accept a Bluetooth pairing
1. Ensure that Bluetooth is turned
on and in visible mode.
2. Tap Yes when prompted to
establish a partnership with the
other device.
3. Enter a passcode (the same
passcode that is entered on the
device requesting pairing) to
establish a secure connection
and tap Next .
NOTE Tap Advanced tab to change the
paired device name and to set the
services you want to use for the
paired device.
4. Tap
Done
To change the display name of a
Bluetooth device
8. After the receiving party enters
the passcode, tap Done to
confirm the partnership.
1. Press the Start Key
, tap
Settings
, then tap Bluetooth
NOTE Creating a Bluetooth pairing
2. Tap a Bluetooth device.
between two devices is a one-time
process. Once a pairing
partnership is created, the devices
can recognize each other and
exchange information without
entering a passcode again.
3. Tap
Properties
4. Enter a new display name for the
Bluetooth device in the Nickname
field, then tap Done .
JS750 81
Using the Today Screen
To delete a Bluetooth pairing
1. Press the Start Key
, tap
Settings
, then tap Bluetooth
2. Tap a Bluetooth device.
3. Tap Menu , tap Delete, and then
tap Yes in the confirmation
screen.
Connecting a Bluetooth
hands-free or stereo headset
For hands-free phone conversations
or to listen to music, you can use a
Bluetooth hands-free or stereo
headset.
To connect a Bluetooth hands-free
or stereo headset
1. Make sure that both your phone
and the Bluetooth headset are
turned on and that the headset
is in visible mode. Refer to the
manufacturer’s documentation to
find out how to set the headset
in visible mode.
82 JS750
2. Press the Start Key
, tap
Settings
then, tap
Bluetooth
3. On My Devices tab, tap Add.
4. Tap the name of the Bluetooth
headset, then tap Next . The
phone will automatically pair with
the Bluetooth headset.
Windows Mobile will automatically
try one of the preconfigured
passcodes (0000, 1111, 8888,
1234) to pair the Bluetooth headset
with the phone. If this fails, you have
to manually enter the passcode
delivered with your headset.
NOTE If the Bluetooth stereo headset
becomes disconnected, turn the
headset on and repeat steps 1 to
3 above, then select the stereo
headset. Tap Menu , then tap
Set as Wireless Stereo.
3.12.9 Microsoft My Phone
3.14 RSSViewer
Microsoft My Phone allows you to
synchronize your phone's contacts,
calendar, tasks, text messages, music,
photos, videos and other documents
with your My Phone account at
http://myphone.microsoft.com. You
can configure this service on your
phone using the Settings tab of
Microsoft My Phone.
RSS Viewer is an RSS reader that
keeps you up-to-date with the
latest news from the Internet. It
monitors Internet news channels
and downloads the most current
news updates and podcasts so you
are instantly informed of breaking
news and events. For more
information and tips on using RSS
Viewer, see Help on your phone.
1. Press the Start Key
, scroll
the screen up, then tap
Microsoft My Phone
or
NOTE Make sure you have an active
Internet connection (such as WiFi or a data connection) before
using RSS Viewer.
Press the Start Key
, tap
Settings
,then tap Microsoft
My Phone
2. Tap
Next
3. Tap the Privacy Statement and
Service Agreement links, review
these documents, then tap
Accept .
4. Tap the sign in box and enter
your Windows Live ID.
5. Tap the password box and enter
your password in the password
box, then tap Sign In .
JS750 83
Using the Today Screen
Subscribing to and organizing
news channels
You must subscribe to news
channels before you can receive
RSS feeds.
To subscribe to news channels
1. Press the Start Key
tap RSS Viewer
, then
2. Tap Channels
and a
list of RSS channels is displayed.
3. Tap the channels you want to
subscribe to, then tap New
in the task bar.
4. Select the check boxes of the
RSS channels you want to
subscribe to, then tap Done
Done .
TIP
Channels are grouped by
categories. If you want to select
all channels in a category, tap the
category check box.
5. The channel list appears. Tap
Refresh to update the channels.
3.15 Alarmas
You can set up to three alarms that
activate or deactivate with a simple
tap. See page 73 for details.
SHORTCUTS
There are two shortcuts to the
Clock and Alarms panel. Tap Set
Set in the Options taskbar
from the Today Screen, or tap the
Clock standby panel from the
Today Screen.
1. Press the Start Key
tap Alarms
, then
2. Tap an alarm to display the Alarm
Settings, then tap fields and
enter information as necessary.
To activate and deactivate
alarm(s)
If your schedule changes temporarily,
disable a set alarm simply by tapping
the checkbox next to it. The X is
removed, but the settings remain
allowing you to simply tap the
checkbox to reactivate later.
When an alarm sounds
When an alarm goes off, you can
choose to Snooze or Dismiss the
alarm. When you touch and drag
Snooze
the alarm will sound
again after five minutes.
84 JS750
3.16 Calendario
Use Calendar to schedule
appointments, including meetings
and other events. If you use
Outlook on your PC, you can
synchronize appointments between
your phone and PC.
SHORTCUT
Double-tap calendar from the
Today Screen.
Creating an appointment
Location: Manually enter using
the keyboard or tap Arrow
then tap one of the listed
locations (based on previous
entered locations).
Starts: Manually enter the
appointment time or tap Arrow
and tap the time to set.
Ends: Manually enter the time or
tap Arrow
and tap the time
to set.
All Day: Tap Yes or No.
1. Press the Start Key
, scroll
the screen up, then tap Calendar
Occurs: Tap the appointment
recurrance.
2. Tap the current date at the top
of the screen to display the
current month.
Reminder: Tap None or Remind
me. If Remind me is selected,
enter when to remind you.
TIP
Categories: Tap checkbox
(Business/ Holiday/ Personal/
Seasonal), then tap OK .
Tap the arrow icons to move to
the next/previous dates or tap
Today
to return to the
current date.
Attendees: Tap
or
then add
3. Tap Options
, then tap New
Appointment.
4. Enter appointment information.
Subject: Manually enter using
the keyboard or tap Arrow
then tap one of the listed
subjects.
attendees as necessary.
Status: Tap Free, Tentative,
Busy, or Out of Office.
JS750 85
Using the Today Screen
Sensitivity: Tap Normal ,
Personal, Private or
Confidential.
5. When the appointment settings
are complete, tap OK .
NOTE All-day events do not occupy
blocks of time in Calendar;
instead, they appear in banners at
the top when viewing the day's
agenda.
Viewing your appointments
View your schedule in Day, Agenda,
Week, Month, or Year view.
1. Press the Start Key
, scroll
the screen up, then tap Calendar
2. Tap
in the Options task bar,
and your day's appointments are
listed. Tap to change to the next
appointment view (each tap
changes to the next view).
Sending meeting requests and
appointments
You can send meeting requests via
e-mail to persons that use Outlook
or Outlook Mobile. You can also
send a calendar appointment to
another phone using MMS.
To send a meeting request
1. Press the Start Key
, scroll the
screen up, then tap Calendar
86 JS750
2. Schedule a new appointment (or
open an existing appointment)
scroll down to Attendees tap No
Attendees. Tap
or
3. Tap the contact(s) you want to
send the meeting request to and
tap OK .
NOTE Only contacts that contain email
addresses can be selected as
attendees.
4. On the New Appointment screen,
tap OK . The meeting request is
sent out.
NOTES • You can only specify if an
attendee is required or optional
if your phone is connected to a
Microsoft Exchange Server 2007
or later. Otherwise, all attendees
are designated as required. For
more information, see Chapter 7.
• To remove an attendee from the
list, select the attendee and tap
Options
, then tap Remove
Attendee.
• When attendees accept your
meeting request, the meeting is
automatically added to their
schedules. When their response
is sent back to you, your
calendar is updated as well.
3.17 Tareas
Use Tasks to keep track of things
you need to do.
To create a task
1. Press the Start Key
, scroll
the screen up, then tap Tasks
2. Tap Menu
Task.
, then tap New
3. Enter task details including
Priority, Status, Starts, Due,
Occurs, Reminder, Categories,
and Sensitivity.
4. When finished, tap
OK
NOTES • You can synchronize information
on your phone with your PC to
keep your task list up to date in
both locations.
• If you create a new task with a
reminder on your PC and then
synchronize tasks with your
phone, the reminder will play at
the time that was set on your
PC.
To manage your Tasks list
1. Press the Start Key
, scroll
the screen up, then tap Tasks
JS750 87
Using the Today Screen
2. Tap Options
to access task
management options.
New Task: Starts a new task
entry.
Delete Task: Deletes the selected
task.
Edit: Allows edits.
Options: Enables reminders and
shows dates and Task entry bar
on the Tasks panel.
Sort By: Sorts by Status, Priority,
Subject, Start Date, or Due Date.
Filter: Filters list view to include
either active or completed tasks
plus shows All Tasks or selected
task categories.
Send via Bluetooth: Allows you
to send a task via Bluetooth®.
Send as vCalendar: Starts
message (video or picture) with
task attached.
To mark a task as completed
1. Press the Start Key
, scroll
the screen up, then tap Tasks
88 JS750
2. Tap the checkbox next to the
task to mark it as completed (tap
again to unmark).
3.18 Notas
Notes helps you to quickly capture
thoughts, questions, reminders, todo lists, and meeting notes. You can
create handwritten and typed notes,
record voice notes, convert
handwritten notes to text for easy
readability, and send notes to others.
1. Press the Start Key
, scroll
the screen up, then tap Notes
Entering Information in Notes
●
You can enter typed text by using
the on-screen keyboard or
handwriting recognition software.
You can also use the stylus which is
attached on the back side of the
device to write or draw directly on
the screen. Tap Options
in the
Options taskbar, then tap View
Recording Toolbar to record sound
directly on your note.
1. Press the Start Key
, scroll
the screen up, then tap Notes
2. Tap New Note
new note.
Note file storage
to write a
3. Tap Keyboard
then tap OK .
, type the note,
Managing Note entries
1. Access Notepad and tap an entry.
2. Tap Options
●
●
Erase a note
Tap Tools, tap Delete, then tap
Yes.
Rename or move a note
Tap Tools, tap Rename/Move,
then enter changes as necessary.
Send a note
Tap Tools, tap Send, then
complete message fields as
necessary and tap Send .
You can file your Notes into specific
file folders for easy organization and
retrieval. To select a file folder to
view, tap All Folders in the upperleft corner of the screen, then tap
the file folder to open.
To change how your Notes are
sorted, tap Name in the upperright corner of the screen, then tap
how you want to sort your notes.
3.19 Explorador de archivos
The File Explorer application allows
you to open an explorer window
similar to a desktop Windows based
system. The explorer window allows
you to navigate through your phone
to locate and manage desired
folders and files.
The file structure starts with
location (phone memory or storage
card memory), then lists category
folders. Within the category folders
are sub-folders and/or documents.
JS750 89
Using the Today Screen
1. Press the Start Key
, scroll
the screen up, then tap File
Explorer
2. Tap a file folder from those listed,
then tap the folders (or file) you
want.
To change the current location
Tap the current folder in the
upper left corner of the LCD,
then tap a folder from the dropdown menu.
To manage your files
Tap Menu , then tap New Folder
to create a new folder, tap
Rename to change the name of
the highlighted item, folder, tap
Delete to delete the highlighted
item, folder, or tap Edit to edit
(cut, paste, and more) the
highlighted item.
To manage the file list
Tap Menu , then tap Refresh to
refresh the list, tap Sort By to
change how the list is sorted.
90 JS750
To open a file on a network
To use Microsoft Office Mobile
Tap Menu , tap Go To, tap
Open Path, tap New Path, enter
the new path, then tap OK .
1. Press the Start Key
, scroll
the screen up, then tap Office
Mobile
TIP
Tap and hold a file to bring up a
pop-up menu with options to cut,
copy, rename, delete, send, or set
as Home background.
3.20 Office Mobile
Microsoft® Office Mobile consists of
four applications that let you create,
view, and edit Microsoft documents.
These four applications are:
●
Microsoft® Office Word Mobile:
view and edit Microsoft Word
documents and text files.
●
Microsoft® Office Excel® Mobile:
use Microsoft Excel worksheets.
●
Microsoft® Office PowerPoint®
Mobile: view Microsoft
PowerPoint slides.
●
Microsoft® Office OneNote®
Mobile: lets you easily create
notes with audio and images.
2. Tap the Office Mobile application
that you want to use.
NOTE Word Mobile and Excel Mobile do
not fully support some features of
Microsoft® Office Word and
Microsoft® Office Excel®.
Microsoft Mobile document
formats
By default, Word Mobile saves
documents in .docx format, while
Excel Mobile saves workbooks in
.xlsx format. If you want to open
these file types on a computer that
uses Microsoft Office 2000, Office
XP, or Office 2003, you may need
to download and install the File
Format Converter in your computer.
You can find this converter at
http://www.microsoft.com/downloa
ds/details.aspx?FamilyId=941B3470
-3AE9-4AEE-8F43C6BB74CD1466&displaylang=en.
JS750 91
Using the Today Screen
Changing document format on
your device
To save a Word Mobile file in a
different format, tap Menu , tap
Tools, tap Options, tap Default
template arrow
, tap Word 972003 Document (.doc), then tap
OK .
NOTE If no document is opened, tap
Menu , then tap Options to
access the Default template
settings.
To save Excel Mobile workbooks in
the .xls format, start Excel Mobile,
but do not open a workbook. Tap
Menu , tap Options, tap Template
for new workbook
, tap Blank
97-2003 Workbook, then tap OK .
3.21 Imágenes y Vídeos
Pictures & Videos allows you to
view and manage media files on
your phone.
SHORTCUT
Double-tap pictures from the
Today Screen to view picture files.
To view media files
1. Press the Start Key
, scroll
the screen up, then tap Pictures
& Videos
2. Tap a media file to view or play
back the file.
TIP
You can make minor touch ups to
the picture such as rotate, crop,
and auto correct. View a file, tap
Menu , then tap Edit. To rotate,
tap Rotate . To crop or auto
correct, tap Menu again, then
tap Crop or Auto Correct.
NOTE If you cannot find the media file
in the default My Pictures folder,
tap My Pictures at the top left
side of the screen, tap My
Device, then browse the folders.
Picture and Video files
There are a number of things you
can do with your picture and video
files beyond simple viewing. You can
send the selected file, beam it to
another device, or play a slide show.
, scroll
1. Press the Start Key
the screen up, then tap Pictures
& Videos
2. Highlight a media file, then tap
Menu .
92 JS750
NOTE The available menu options
depend on the selected media
file.
File tools
●
Tap Tools, then tap Properties
to view the detail properties of
the selected file.
●
Tap Tools, then tap Sort By to
change the sort to Name, Date
or Size.
●
Tap Tools, then tap Options to
customize picture settings and
slideshow playback preferences.
Send the media file
Tap Send, tap the account to use,
then complete the fields as
necessary to send the message or
email.
Manage your media file(s)
●
Tap Delete, then tap Yes.
●
Tap Edit, then tap Cut or Copy.
●
Tap Go To to jump to another
file area, such as My Device.
Using Pictures
●
Tap Save to Contact, then tap
the contact you want to set with
with the picture.
●
Tap Play Slide Show. To display
control buttons to rotate, play,
pause, rewind, fast-forward, or
exit, tap the screen.
●
Tap Set as Home Background,
tap the percent of transparency,
then tap [ok graphic].
TIP
Tap and hold a file to display a
pop-up menu for that file to cut,
copy, delete, send, or set as
Home Background.
To copy a picture or video clip to
your phone
You can copy pictures and video
files from your PC to the My
Pictures folder on your phone, and
then view them on your phone. For
more information about copying
files from your PC to your phone,
see Windows Mobile Device Center
or ActiveSync Help on your PC.
JS750 93
Using the Today Screen
NOTE You can also copy pictures and
video files from your PC to your
phone using a storage card. Install
the storage card to your phone,
and then copy them from your PC
to the folder you created on the
storage card.
3.22 Windows Media
You can use Microsoft Windows
Media Player 10 Mobile for Pocket
PC to play digital audio and video
files that are stored on your device
or on a network, such as on a Web
site.
Using Windows Media Player, you
can play both audio and video files.
The following file formats are
supported by this version of
Windows Media Player: WAV, WMA,
WMV, MP3, MIDI, AAC, MP4 and
more.
1. Press the Start Key
, scroll
the screen up, then tap Windows
Media
94 JS750
Playback Screen
The Playback screen displays the
playback controls (such as Play,
Pause, Next, Previous, and Volume),
album art window, and video
window. You can change the
appearance of the default Playback
screen by choosing a different skin.
When you are viewing the Playback
screen, tap Menu to access the
following commands.
Icon
●
Library: Displays the Library screen
so you can choose a file to play.
●
Play/Pause: Starts or pauses
playback.
●
Stop: Stops playback.
●
Shuffle /Repeat: Plays the items
in the Now Playing playlist
randomly/ repeatedly.
●
Full Screen: When a video is
playing, uses the entire screen to
play it.
●
Options: Lets you adjust various
Windows Media Player options,
including Playback, Video,
Network, Library, Skins, and
hardware Button options.
●
Properties: Displays information
about the file currently playing.
●
About: Displays information
about Windows Media Player,
such as the version number and
copyright notification.
Description
Plays/Pauses a file.
Increases volume level.
Decreases volume level.
Returns to the beginning of
the current file or skips to
the previous file.
Skips to the next file.
Adjusts the playback
progress of a selected file.
Turns the sound on or off.
Displays a video by using the
entire screen (full screen).
Displays a Web site where
you can find music and
videos to play.
JS750 95
Using the Today Screen
3.23 World Clock
3.24 Buscar Teléfono
Allows you to view current date and
time in another time zone or
country.
You can search for files and other
items stored on your device in the
My Documents folder or on a
storage card. You can search by file
name or by words located in the
item. For example, you can search in
e-mail messages, notes,
appointments, contacts, and tasks,
as well as in online Help.
To search for a file or an item
1. Press the Start Key
, scroll
the screen up, then tap Search
Phone
2. In Search for box, enter the file
name, word, or other information
you want to search for.
1. Press the Start Key
, scroll
the screen up, then tap World
Clock
2. Tap the area to zoom in to view.
Date and time of the selected
location displays at the bottom
of the screen.
3. Tap Arrows
to move
through World Clock locations.
NOTE Tap Zoom Out
Zoom Out
to the global view.
96 JS750
to return
3. If you have looked for this item
recently, tap drop-down list
in then tap the item from the list.
4. Tap drop-down list in the
Type box, then tap a data type
to help narrow your search.
5. Tap Search in the Options
taskbar.
The My Documents folder and
subfolders are searched.
6. In the Results list, tap the item
you want to open.
3.25 Calculadora
Allows you to perform simple
mathematical calculations.
, scroll
1. Press the Start Key
the screen up, then tap
Calculator
2. Tap available keys to enter data
and perform calculation.
●
Tap the keypad that pops up
to enter numbers.
●
Tap
●
Tap
to delete the whole
digit entered.
●
to enter decimals.
Tap
to delete the last digit
entered.
●
Tap the corresponding Touch
Keys to enter functions (C, R,
+).
●
Tap the corresponding Touch
Keys to use memory keys (M,
MC, MR, M+).
●
Tap
to complete
equation.
3.26 Adobe Reader LE
Adobe® Reader® LE lets you view
Portable Document Format (PDF)
files.
When you open a passwordprotected PDF file, you will be
prompted to enter the password
before the file can be opened.
To open a PDF file on your phone
1. Press the Start Key
, scroll
the screen up, then tap Adobe
Reader LE
2. Browse the folders to find and
open a PDF document:
●
Tap it in the displayed list of
recently opened documents.
●
Tap My Device, tap folders to
open and view contents as
necessary, then tap the PDF
document to open.
NOTE To open another PDF file, tap
, tap Open, tap Browse
, then find and tap the
PDF file. You can also open a PDF
file from File Explorer by tapping
it.
Menu
Browse
JS750 97
Using the Today Screen
To navigate through a PDF file
Access and Options
You can do any of the following:
1. Press the Start Key
, scroll
the screen up, then tap Voice
Commands
●
Tap Tools , then tap Go To and
tap an option to go to a specific
page in the PDF file.
●
Tap Tools , then tap Zoom to
then tap a zoom option (in, out,
%, fit to screen, or fit to width).
●
When using the internal LCD,
press the Navigation Keys up and
down to scroll through the
pages.
3.27 Voice Commands
This feature provides you with the
following options equipped with
AVR (Advanced Voice Recognition)
technology. Each option has its
detailed information on the phone
and you can check it out by tapping
Info .
SHORTCUT
To quickly access Voice
Commands, simply press and hold
the SEND Key
98 JS750
NOTE You can access Voice Commands
using the internal keypad as well.
Open the slide, then press and
hold the Space/Voice Commands
Key
2. To customize your voice
commands, tap Settings .
Confirmation Automatic/ Always
confirm/Never confirm
Sensitivity Most Sensitive /
Recommended/ Least Sensitive
Adaptation If the phone asks
you to repeat your voice
command too often, train the
phone to recognize your voice
patterns.
Prompt Mode Mode/ Timeout
For Mode, set Prompts/ Readout
+ Menu/ Readout/ Tones Only.
For Timeout, set 5 seconds or 10
seconds.
Call 
Go to 
Say ‘Call’ then call someone simply
by saying the phone number or
name. Please speak clearly and
exactly as in your Contacts list.
When you have more than one
contact number, you can state the
name and number type of the
contact (for example, 'Call John
Work').
The 'Go to' command allows you to
access a menu within the phone (for
example, 'Go to Calendar').
If no menu option is stated, a list of
options will be provided.
Send 
Say 'Send Message' and the voice
command will prompt you for the
type of message. After choosing the
message type, system will ask you
for the contact name, number or
group. It will automatically start a
message. If you say a full-sentence
command, such as 'Send Message
to Bob', it would automatically start
a text message without asking for
the message type. When using
'Send Message' command, speak
clearly and say the number, group
name, or name exactly as it is
entered in your Contacts list.
Check 
The ‘Check’ command allows you to
check out a wide range of items
from the battery level, service mode,
signal strength, GPS location,
network status, volume, number of
missed calls, voicemail, messages, to
time and date.
Contact 
You can look up names in your
Contacts (for example, 'Lookup
John'):
Call/ Read out/ Create New/
Modify/ Erase
Redial
Allows you to automatically redial
the last number called.
Play 
Allows you to play songs saved in
the phone.
Help
Provides a general guideline to using
Voice Commands.
JS750 99
Using the Today Screen
3.28 Juegos
Allows you to access your
downloaded games. The game
Solitaire is pre-installed on your
device.
1. Press the Start Key
, scroll
the screen up, then tap Games
2. To play, tap the game that you
want to play.
3.29 Administrador de
tareas
In most cases, programs
automatically close to free needed
memory, however, you can close
programs manually, if you prefer.
SHORTCUT
Press the Task Manager Key
on the right side of the phone.
1. Press the Start Key
, scroll
the screen up, then tap Task
Manager
2. Check the list of running
programs under the Application
column, along with
corresponding Memory usage
and CPU information.
To change how you view the list,
tap Menu .
●
Tap View, then tap Applications
or Processes.
●
Tap Sort By, then tap Memory,
CPU, or Name.
●
Tap Refresh.
3. Manage your tasks as detailed
below:
100 JS750
3.30 Cámara
To open a list item
●
Double-tap the item in the list.
To stop a running application
program
SHORTCUT
●
Tap an application, then tap
End Task to stop individual tasks.
●
Tap Menu , tap End All Tasks,
then tap Yes to confirm to end all
tasks at once.
Tap an application, tap
then tap Switch To.
Menu
To exit
●
Tap
Menu
Press Camera Key
side of the phone.
on the right
1. Press the Start Key
2. Scroll the screen up, then tap
Camera
3. Use the following options to
customize your settings:
To switch tasks
●
3.30.1 Camera
, then tap Exit.
Back
into
Record Video Drag
to change from Camera
mode to Video mode.
My Images
Auto/ Macro
Brightness
Settings
Back
Macro
Capture Mode
Brightness
My Images
JS750 101
Using the Today Screen
NOTE Zoom is adjustable with Side
Volume Keys
(not available at
the highest resolution).
Settings
Normal
Memory In Use Handset Memory/
External Memory
Hide Icon Auto/ Manual
Access the settings below by
tapping the settings icon, then
using your fingertip to turn the
settings wheel and tapping the
setting you want.
Shutter Sound Off/ Shutter 1/
Shutter 2/ Shutter 3/ Shutter 4
Image Size 2048X1536/
1600X1200/1024X768/
640X480/320X240
Reset Settings Reset All
Grid View Off/ Simple Cross/
Trisection
*Zoom is not available in 2048X1536
resolution.
4. Take a picture by pressing the
Take
Camera Key or tap
Photo.
Scene Mode Auto/ Portrait/
Landscape/ Sports/ Night
3.30.2 Video
Color Effect Off/ Sepia/ Mono/
Negative/ Solarize
SHORTCUT
White Balance Auto/
Incandescent/ Sunny/ Fluorescent/
Cloudy
Timer Off/ 3 Sec/ 5 Sec/ 10 Sec
Shot mode Normal/ Continuous
Shot/ Panorama Shot
Preview Style Full Screen/ Full
Image
ISO Auto/ 100/ 200/ 400/ 800
Image Quality Super Fine/ Fine/
102 JS750
Press and hold Camera Key
for
2 seconds on the right side of
the phone.
1. Press the Start Key
2. Scroll the screen up, then tap
Camera
, then drag
to
video icon
3. Use the following options to
customize your settings:
Back
into
Take Picture Drag
to change from Video
mode to Camera mode.
My Videos
Scene Mode Auto/ Portrait/
Landscape/ Sports
Zoom is adjustable with Side
Volume Keys .
Brightness
Settings
Access the settings below by
tapping the Settings icon, using
your fingertip to turn the settings
wheel and tapping the setting you
want.
Video Size 640X480/ 320X240/
176X144
White Balance Auto/
Incandescent/ Sunny/ Fluorescent/
Cloudy
Video Quality Super Fine/ Fine/
Normal
Duration Normal/ MMS
Memory In Use Handset Memory/
External Memory
Voice Mute/ Unmute
Hide Icons Auto/ Manual
Reset Settings Reset All
4. Start a video recording by
pressing the Camera Key or
tapping
Take Video.
5. Stop video recording by pressing
the Camera Key or tapping
Stop Video
Scene Mode Auto/ Portrait/
Landscape/ Sports
Color Effect Off/ Sepia/ Mono/
Negative/ Solarize
Settings
Back
Scene Mode
Brightness
Record Mode
My Videos
JS750 103
Using the Today Screen
3.31 Introducción
●
The Getting Started menu steps you
through the information you need
to get you and your phone up and
running. Some of the items tell you
how to use them, others tell you
how to set them up. When you're
through, you can delete the panel
from the Today Screen though the
Add/remove Getting Started
option.
●
1. Press the Start Key
, scroll
the screen up, then tap Getting
Started
●
●
●
●
●
●
●
●
●
●
●
●
Make a call
Set date and time
Set up Visual Voice Mail
Set up e-mail
Set up Exchange Server
Set up a device password
Set up Wi-Fi
Set up Bluetooth
Set gesture recognition
Set orientation
Set up PC Synchronization
Set background
104 JS750
●
●
Set ring tone
Transfer Music
Online help & how-to
Add/remove Getting Started
3.32 ActiveSync
ActiveSync synchronizes information
on your device with information on
your PC, such as Outlook content.
ActiveSync can also synchronize
over a cellular network with
Microsoft Exchange Server, if your
company or service provider is
running Microsoft Exchange Server
with Exchange ActiveSync. When
you synchronize, ActiveSync
compares the information on your
device with the information on your
PC and/or Exchange Server and
updates all locations with the most
recent information.
NOTE You can download ActiveSync or
Windows Mobile Device Center from
www.windowsmobile.com/getstarted.
With ActiveSync, you can:
●
Synchronize information, such as
Outlook E-mail, Contacts,
Calendar, or Tasks information on
your device with your PC, as well
as pictures, video, and music.
●
Synchronize Outlook E-mail,
Contacts, Calendar
appointments, and Tasks on your
device directly with Exchange
Server so that you can stay up to
date even when your PC is
turned off.
●
Exchange files between your
device and your PC without
synchronizing.
●
Select which types of information
are synchronized and specify how
much information is
synchronized. For example, you
can choose how many weeks of
past Calendar appointments to
synchronize.
Before you can synchronize
information with a PC, first, install
ActiveSync on your PC, then create
a synchronization pairing between
your device and the PC. You can
download ActiveSync from
www.windowsmobile.com/getstarted.
JS750 105
Using the Today Screen
Once you have installed ActiveSync
and set up a synchronization
relationship, ActiveSync on the PC
recognizes your device when you
connect it, and automatically
transfers the synchronization
settings you specified on your
device.
You may be able to synchronize
your device with Exchange Server
through your company or wireless
service provider. If you plan to do
so, obtain e-mail address, Exchange
Server address, user name,
password, and domain name from
your administrator before starting
the Sync Setup Wizard.
3.33 EnableDUN
While traveling, you can use your
Windows Mobile powered phone as
a modem for your notebook. Use
either VZAccess Manager or the
Modem Link program to use your
phone as a USB or Bluetooth
modem.
106 JS750
Before you proceed
●
Make sure your phone has a data
or dial-up modem connection.
For more information about
setting up these connections, see
“Wireless data connection” and
“Dial-up” in this chapter.
●
To connect your device to a
computer via USB, you must first
install Windows Mobile Device
Center or Microsoft ActiveSync
version 4.5 or later on the
computer.
●
To use a Bluetooth connection,
make sure your computer has
built-in Bluetooth capability. If
your computer does not have
Bluetooth, you can connect and
use a Bluetooth dongle.
Setting up your phone as a
USB modem in Windows
Vista ™, Windows 7 or Windows
XP
To set up the phone as a USB
modem, you must first install the
modem driver on your computer
and then activate your phone as a
USB modem.
To install the wireless modem
driver on the computer
1. Download ActiveSync from
www.windowsmobile.com/getstar
ted. Select your language, click
Additional Tools, and then click
Wireless Modem Driver
Installation.
2. Follow the on-screen instructions
to install the USB modem driver.
When installation completes, click
Exit to close the installation
program.
To activate your phone as a USB
modem
Connect your phone to your
notebook using the USB cable, then
follow the steps below to activate
your phone as a USB modem.
NOTE When you activate Wireless
Modem, ActiveSync and Windows
Mobile Device Center will be
disabled automatically.
1. Press the Start Key
, tap
Settings
, tap Connections
, tap Switch USB
, then
tap VZAccess Manager.
2. Tap Save , tap OK , then the
handset will restart.
Next, create a modem dial-up
connection. The procedures for
creating a modem dial-up connection
are different for Windows Vista™,
Windows 7 or Windows XP. Refer to
“Creating a modem dial-up
connection” later in this chapter for
details.
JS750 107
Using the Today Screen
Setting up your phone as a
Bluetooth modem in Windows
Vista ™ or Windows 7
You can connect your phone to a
notebook or desktop computer
through Bluetooth and use the
phone as a modem for the
computer. To connect your phone
to the computer through Bluetooth,
your computer must be Bluetooth
enabled or you must have a USB
Bluetooth dongle.
To set up a Bluetooth connection
between your phone and Windows
Vista™ or Windows 7 computer
1. On your phone, turn on
Bluetooth and set it to Visible
mode.
2. Connect a Bluetooth radio
adapter on your computer. (Refer
to the manufacturer’s
documentation for details on
how to install).
After a Bluetooth radio adapter is
installed on your computer, the
Control Panel and System Tray
will have the Bluetooth Devices
icon. Right-click this icon then
click Open Bluetooth Settings.
108 JS750
3. In the Bluetooth Devices window,
click Add.
4. The Add Bluetooth Device
Wizard opens. Select the
checkbox My device is set up
and ready to be found then click
Next.
5. The wizard then detects your
device and displays its name in
the dialog box. Select the phone
name then click Next.
6. Select Let me choose my own
passkey then enter a passcode
(up to 16 digits) that will serve
as an identification number for
establishing a secure connection
between your phone and the
computer. Click Next.
7. A confirmation message then
appears on your phone. Tap Yes
to accept the connection, enter
the same passcode, then tap
Next.
8. On the computer, click Finish to
exit the wizard.
9. On your phone tap
Done
To add your phone as a Bluetooth
modem to your Windows Vista™ or
Windows 7 computer
After you have finished creating a
Bluetooth connection between your
phone and computer, Windows
Vista™ or Windows 7 automatically
detects your device and then
installs it to your computer as a
Bluetooth modem.
3.34 Domain Enroll
Enroll your phone in your
company’s domain to let System
Center Mobile Device Manager
manage the phone. Ask your
network administrator for more
details.
1. Press the Start Key
, tap
Settings
, tap Connections
, then tap Domain Enroll
2. Follow the on-screen instructions
to enroll domain.
JS750 109
Chapter 4 Entering Text
4.1 On-screen Input Methods
When you start a program or select a field that requires text or numbers,
the Input Panel icon is displayed on the Options taskbar.
Tap the Input Selector arrow (next to the Input Panel icon) to open a menu
where you can select a text input method and customize input options.
After selecting a text input method, the corresponding Input Panel is
displayed, which you can use to enter text.
Tapping
[abc/123 icon]
abc/123
Mode
Show/Hide Input Panel
110 JS750
4.2 Using the QWERTY Keyboard
The QWERTY Keyboard is a full on-screen QWERTY keyboard layout similar
to a computer keyboard.
To enter text using the QWERTY Keyboard
1. Start a program that accepts text input, such as Word Mobile.
2. Tap Show Keyboard
if the keyboard isn't already displayed.
3. Start tapping keys on the keyboard to enter your text.
As you tap the keys, the activated character displays on top of the key.
To learn how to enter text using predictive XT9 mode, see “Using XT9
Mode” in the following page.
JS750 111
Entering Text
4.3 Using XT9 Mode
XT9 is a predictive text input mode
which displays a word candidate list
as you enter characters so you just
tap the word in the list that you want.
To add a word to the XT9
dictionary
If the word that you have entered is
not found in the dictionary, you can
add it to the dictionary.
To enter text using Predictive
mode
1. While in XT9 mode, type a letter
and then tap
until you get to
the Add Word? option.
1. While the cursor is in a text entry
field and the keyboard is
displayed, tap XT9 Input to
enter XT9 input mode.
2. Tap Add Word? then type the
word you want to add, and then
tap Done .
2. Start entering the first few letters
of a word. As you enter each
letter, predicted words appear in
the word candidate bar.
3. Tap the desired word to enter. If
the word is highlighted in the
word candidate bar, you can also
tap the Space bar or Enter key to
enter it.
NOTE If there are several words to
choose from, tap the left or right
directional arrow keys below the
input panel to navigate through
the word candidate list.
112 JS750
4.4 Using Numeric and
Symbol Mode
Switch to Numeric and Symbol
mode to easily enter numbers and
common symbols such as
parentheses, braces, currency signs,
punctuation marks, and special
characters.
To switch to Numeric and Symbol
mode
1. While using QWERTY Keyboard
tap 123
2. Locate and tap the desired
number or symbol to enter it.
abc mode
123 mode
JS750 113
Chapter 5 Synchronizing Information
5.1 About
Synchronization
●
Sync your phone with your
Outlook work account on the
Exchange Server.
For more information about
setting up your phone to sync
with the Exchange Server, see
Chapter 7.
●
Sync your phone with Microsoft
My Phone.
If you have a Microsoft My
Phone account, you can sync and
restore the contacts, calendar
appointments, photos, and other
information that you stored on
your account to your current
Windows phone.
You can take information wherever
you go by synchronizing it to your
phone. There are different ways you
can sync your phone:
●
Sync information from your
computer to your phone.
The following types of
information can be synchronized:
Microsoft® Office Outlook®
information - Office Outlook
email, contacts, calendar, tasks,
and notes.
Notes created using Microsoft®
Office OneNote® 2007
Media - Pictures, music, and
video.
Favorites - Website addresses
you save as Favorites in Internet
Explorer on your phone or in the
Mobile Favorites folder of Internet
Explorer on your computer.
Files - Documents and other files.
114 JS750
5.2 Before Synchronizing
with Your Computer
Before you can sync your phone,
you must first install and set up the
synchronization software on your
computer. For more information, see
“Setting Up Windows Mobile Device
Center on Windows 7 or Windows
Vista®” and “Setting Up ActiveSync®
on Windows® XP” in this chapter.
After installing the synchronization
software on your computer, connect
the phone to your computer using
the USB sync cable. When the
Connect to PC screen appears on
your phone, tap ActiveSync, and
then tap Done .
You can also sync information with
your computer using Bluetooth. See
“Synchronizing via Bluetooth” later
in this chapter.
NOTES • ActiveSync or Windows Mobile
Device Center only syncs data
on your computer and phone. If
you have installed a storage
card and you want to back up
files from the storage card, use
Windows Explorer on your
computer to copy files from the
storage card to your computer.
• If you are sending your phone
for repair or performing a hard
reset, data from your phone will
be lost. It is recommended that
you sync your phone to your
computer to back up your files.
To back up files from the
storage card to your computer,
use Windows Explorer to copy
files from the storage card to
the computer.
5.3 Setting Up Windows
Mobile® Device Center
on Windows 7 or
Windows Vista™
Microsoft Windows Mobile®
Device Center is the replacement
for Microsoft® ActiveSync® on
Windows 7 or Windows Vista®.
Some versions of Windows Vista®
come with Windows Mobile Device
Center already installed. If Windows
Mobile Device Center is not
available on your Windows Vista®,
you can go to the following website
for information on downloading and
installing Windows Mobile Device
Center to your computer:
http://www.windowsmobile.com/get
started.
Setting up synchronization in
Windows Mobile Device
Center
When you connect your phone to
your computer and start Windows
Mobile Device Center for the first
time, you are asked to create a
Windows Mobile partnership with
your phone. To create a partnership:
1. Connect your phone to your
computer using a USB cable.
JS750 115
Synchronizing Information
Windows Mobile Device Center
configures itself, then opens.
On Windows Mobile Device Center,
you can do the following:
2. On the license agreement screen,
click Accept.
●
Tap Mobile Device Settings to
change synchronization settings.
3. On the Windows Mobile Device
Center’s screen, click Set up your
device.
●
When you tap Pictures, Music
and Video, then tap New
pictures/video clips are
available for import, a wizard
guides you to tag and transfer
photos from your phone to the
Photo Gallery on your computer.
●
When you finish the setup wizard,
Windows Mobile Device Center
syncs your phone automatically.
Outlook email messages and other
information appear on your phone
after synchronization.
Tap Pictures, Music and Video,
then tap Add media to your
device from Windows Media
Player to sync music and video
files using Windows Media®
Player. For more information, see
“Using Windows Media® Player
Mobile” in Chapter 11.
●
Tap File Management, then tap
Browse the contents of your
device to view documents and
files on your phone.
Using Windows Mobile Device
Center
NOTE See Windows Mobile Device
NOTE Choose Connect without setting
up your device if you only want
to transfer media files, check for
updates, and explore your phone
but not sync Outlook information.
4. Select the items you want to
sync, then click Next.
5. Enter a name for your phone,
then click Set Up.
To open Windows Mobile Device
Center, click Start
> All
Programs > Windows Mobile
Device Center on your Windows
Vista™ or Windows 7 computer.
116 JS750
Center Help for more information.
5.4 Setting Up
ActiveSync® on
Windows® XP
On a Windows® XP computer, you
need to use Microsoft ActiveSync®
4.5 or later. If you do not have this
software on your computer, you can
go to the following website for
information on downloading and
installing Windows Mobile Device
Center to your computer:
http://www.windowsmobile.com/get
started.
Setting up synchronization in
ActiveSync
1. Connect your phone to your
computer. The Synchronization
Setup Wizard automatically starts
and guides you to create a
synchronization partnership.
2. Follow the steps to set up the
partnership between your phone
and your PC.
5.5 Synchronizing With
Your Computer
Connect and sync your phone with
your computer using the USB cable
or Bluetooth connection.
Starting and stopping
synchronization
You can manually sync either from
your phone or computer.
From your phone
●
Press the Start Key
, scroll
the screen up, tap ActiveSync
then tap Sync. To end
synchronization before it
completes, tap Stop.
TIP
To delete a partnership with one
computer completely, disconnect
your phone from that computer
first. In ActiveSync on your
phone, tap Menu Menu , tap
Options, tap the computer name,
then tap Delete.
3. Click Finish.
When you finish the wizard,
ActiveSync syncs your phone
automatically.
JS750 117
Synchronizing Information
From ActiveSync on your
computer
1. In ActiveSync on your phone, tap
Menu , then tap Options .
When you connect your phone to
your computer, ActiveSync
automatically opens on your
computer and syncs.
2. Select the check box next to the
item(s) you want to sync. If you
cannot select a check box, you
might have to clear the check box
for the same information type
elsewhere in the list.
●
To manually start
synchronization, click Sync.
●
To end synchronization before it
completes, press
Selecting information to sync
You can select information type(s)
and amount of information to sync
on either your phone or computer.
Follow the steps below to change
synchronization settings on your
phone.
NOTE Before changing synchronization
settings on your phone,
disconnect it from your computer.
118 JS750
3. To change synchronization
settings for an information type,
for instance, E-mail, select it and
tap Settings. You can then set
the download size limit, specify
the time period of information to
download, and more.
NOTES • Some information types such as
Favorites, Files and Media
cannot be selected in
ActiveSync Options on your
phone. You can only select or
clear these items from your
computer’s Windows Mobile
Device Center or ActiveSync.
• A computer can have sync
partnerships with many different
Windows Mobile powered
devices, but a device can have
sync partnerships with two
computers at most. To ensure
that your phone syncs properly
with both computers, set up the
second computer using the
same synchronization settings
you used on the first computer.
• Outlook email can be
synchronized with only one
computer.
Troubleshooting sync
connection problem
In some cases, when the computer
connects to the Internet or a local
network, it may disconnect the
connection with your phone in favor
of the Internet or network
connection.
If this happens, press the Start Key
, tap Settings
tap
Connections
, tap USB to PC
, then clear the checkbox Enable
advanced network functionality.
This makes your computer utilize a
serial USB connection with your
phone.
5.6 Synchronizing via
Bluetooth
NOTE To connect and sync your phone
with a computer via Bluetooth,
your computer must have built-in
Bluetooth or Bluetooth adapter
(or dongle) installed.
To sync with a computer via
Bluetooth
1. Install Windows Mobile Device
Center or ActiveSync on your
computer to sync through
Bluetooth. Use the program’s
Help section for instructions.
2. Make sure that Bluetooth on
your phone and the computer
are both turned on and set to
Visible mode.
3. On your phone, press the Start
Key
, then tap ActiveSync
4. Tap Menu , then tap Connect
via Bluetooth.
You can connect and sync your
phone with the computer using
Bluetooth.
If this is the first time you have
connected to this computer via
Bluetooth, you must first set up a
Bluetooth pairing between your
phone and the computer.
JS750 119
Synchronizing Information
5.7 Synchronizing Music
and Video
If you want to carry your music or
other digital media along with you
while you travel, set up Windows
Media® Player on your computer to
sync music and video with your
phone.
Other than selecting the Media
information type to be
synchronized, all media
synchronization settings must be set
in Windows Media® Player. Before
media can be synchronized, you
must do the following:
1. Install Windows Media® Player
Version 11 on your computer.
(Windows Media® Player 11
works only in Windows XP or
later versions).
2. Connect your phone to the
computer with a USB cable. If
your phone is currently
connected using Bluetooth, you
must end that connection before
media can be synchronized.
3. Set up a sync partnership
between your phone and your
computer’s Windows Media®
Player.
120 JS750
4. Add files from your Library to the
Sync List and Click Start Sync to
sync with your phone.
5.8 Synchronizing with
Microsoft® My Phone
Microsoft® My Phone syncs
information between your phone
and Microsoft's password-protected
web site. You can back up and
restore your contacts, calendar
appointments, photos, and other
information.
NOTE You can sync contacts, calendar,
and tasks with My Phone only if
your phone does not have a sync
partnership with an Exchange
Server.
You can also use a web browser on
your computer to:
●
Add, edit, and delete contacts
and calendar appointments.
These changes are then
synchronized with your phone.
●
View your photos and videos,
and save them to your computer.
NOTE If the information you select for
synchronization exceeds the
available storage space on your My
Phone account, My Phone stops
transferring files. For more
information on using My Phone,
see: http://myphone.microsoft.com
Setting up your My Phone
account
Whether you are setting up a new
account or synchronizing to an
existing account, the first step is to
set up My Phone on your phone.
, scroll
1. Press the Start Key
the screen up, then tap
Microsoft My Phone
or
Press the Start Key
, tap
Settings
, then tap Microsoft
My Phone
2. Follow the instructions in the
wizard to set up your My Phone
account.
During setup:
●
Sign in using your Hotmail or
Windows Live address and
password.
●
Set the sync method to
Automatic or Manual, depending
on your preference.
Changing sync settings
To change sync settings such as the
sync schedule and items to
synchronize, you need to access the
settings from the menu.
To change which items to sync
1. Press the Start Key
, scroll
the screen up, then tap
Microsoft My Phone
or
Press the Start Key
, tap
Settings
, then tap Microsoft
My Phone
2. Tap Menu , then tap Sync
Options.
3. Select the items you want to
include or exclude during
synchronization.
4. Tap
Done
JS750 121
Synchronizing Information
To adjust sync schedule and
roaming settings
Stopping the sync partnership
with your My Phone account
1. Press the Start Key
, scroll
the screen up, then tap
Microsoft My Phone
You can stop synchronizing with
your My Phone Web account on
your phone. This does not delete
the data already synchronized to
your phone and the data stored on
your My Phone Web account.
or
, tap
Press the Start Key
Settings
, then tap Microsoft
My Phone
2. Tap Menu , then tap Sync
Schedule.
3. Select from the available
schedule options.
4. To enable automatic sync while
roaming (when you are out of
range of your home network),
select the check box Use these
settings when roaming.
5. Tap
Done
122 JS750
, scroll
1. Press the Start Key
the screen up, then tap
Microsoft My Phone
or
, tap
Press the Start Key
Settings
, then tap Microsoft
My Phone
2. Tap
Menu
, then tap Account.
3. Tap Stop Service, then tap Yes.
Managing your My Phone
Web account from your
computer
You can use a Web browser on your
computer to access your My Phone
Web account and:
●
Add, edit, or delete contacts,
calendar appointments, and
other types of information.
Changes will be synchronized
with your phone.
●
View photos and videos that are
stored on your My Phone
account, delete them, save them
to your computer, and more.
To access your My Phone Web
account from your computer, go to
http://myphone.microsoft.com, and
sign in using your Hotmail or
Windows Live address and
password.
JS750 123
Chapter 6 Exchanging Messages
6.1 Text Messages
Send short text messages (SMS) to
other mobile phones. If your
message is more than 160
characters, it will be sent as two or
more separate messages and you
will be billed accordingly.
Creating and sending a new
text message
1. Double-tap message from the
Today Screen, then tap New on
the Options taskbar at the
bottom of the screen.
●
Tap Contact
, tap a contact,
then tap Done .
●
Tap Message History
, tap a
message, then tap Done .
●
Tap Call History
then tap Done .
●
Tap Dialpad
, tap keys to
manually enter a destination,
then tap Done .
TIP
, tap a call,
To delete a recipient, tap
the right of the entry.
to
4. Tap the text area and enter your
message, then tap Done .
NOTE If you have unread messages, tap
text, swipe horizontally past
pending messages (No New
Messages is displayed), then tap
the Message panel again.
2. Tap Text message.
3. Tap the To: text field to enter the
mobile phone number or to
select from the following options:
124 JS750
TIPS
• To choose from preset
messages, tap Menu , tap
Insert My Text and tap a
desired message.
5. When finished, tap
Send .
Done
then
Managing text messages
Deleting and copying messages in
your Inbox is easy.
To copy a text message to the SIM
card
Making calls directly from text
messages
1. Press the Start Key
tap Message
While you are viewing a text
message from the Today Screen
Messages panel or in your Inbox,
you can directly call the sender of
the message, if the sender’s phone
number is stored in your contacts.
, then
2. Tap a message to open it, then
tap OK to close it.
3. With the message now
highlighted, tap Menu , then tap
Copy to SIM.
NOTES • You cannot copy sent messages
to the SIM card.
• Copying text messages from your
phone to the SIM card results in
duplicate messages in the Inbox
when your SIM card is in use.
To delete one or more text
messages
1. Open the Messaging Inbox.
2. Tap
, tap Delete, then tap
the checkmarks to the left of
each message.
Menu
1. Open the text message, press the
SEND Key
2. Verify that the correct number is
about to be dialed, if it is, press
the SEND Key
again.
NOTE Tapping a phone number that is
contained in a text message also
allows you to call that number.
6.2 Multimedia Messages
Sending multimedia messages
(MMS) to your friends and family is
fun and easy. You can include
pictures, audio clips and videos,
along with text.
3. Tap Done to delete the
selected messages.
JS750 125
Exchanging Messages
To configure MMS message
settings
1. Press the Start Key
tap Message.
, then
2. Tap Settings.
3. Tap the MMS Settings Tab.
4. Set your preferences.
5. Tap
OK
Creating and sending MMS
messages
You can compose MMS messages in
a combination of slides, where each
slide can consist of a photo, video
or audio clip, and/or text.
To compose an MMS message
1. Press the Start Key
Message.
and tap
2. Tap New Message.
3. Tap Picture Message or Video
Message.
4. Tap the To: field to enter the
recipient's phone number or email address (use Contact
Message
, Call History
Dialpad
, or Blog
) then
tap Done .
TIP
To designate as Cc or Bcc, tap
Arrow
next to the addressee
and tap the designation you want
to set for it.
4. Tap Done again when finished
adding recipients.
5. Depending on the type of
message you selected (Video or
Picture), the attachment options
will vary. Choose from the
following options:
126 JS750
●
●
●
Tap Picture
, then tap the
picture to insert.
Tap Video
, then tap the
video clip to insert.
Tap
to take a photo and
insert it into the Picture message.
●
Tap
to record MMS video
and insert it into the Video
message.
●
Tap Mic
to record an audio
clip and insert it into the Picture
message.
●
Tap Audio
, then tap the
audio file to attach. For more
information, see page 132.
●
Tap
to add other
attachments, then tap Vcard
to insert vCard from your
Contacts, tap Vcal
to insert
vCal from your Calendar, or tap
File
to insert a data file
stored on your phone.
NOTE To add slides manually, tap
Menu
, tap Slides, tap Insert
Slide.
8. Tap Send to send the MMS
message.
TIP
You can also send an MMS
message from Camera, Album or
Pictures & Videos.
Adding attachments to a Text
Message
Once you start an SMS message,
tap the text area to bring up the
text entry box Insert text here.
Simply begin tapping the screen
keyboard to enter your text. You
can insert additional items into your
text including:
●
Tap Emoticon
graphics.
to insert face
●
Tap Favorites
to insert
favorite websites.
6. Enter the subject and message
text.
●
Tap My Text
Text phrases.
7. Slides are added automatically
each time you add more of the
same types of attachments.
●
Tap
●
Tap
to insert information
about a Calendar event.
to insert My
to insert a Contact.
JS750 127
Exchanging Messages
To add an audio clip to a Picture
Message
You can add one audio clip per slide
in your Picture message.
1. Start a Picture message, then tap
Audio
, By default, the My
Sounds folder is shown.
NOTE Tap Up
Up
in the Options
taskbar to move up one level in
the folder hierarchy (e.g., from My
Sounds to My Documents. This
is helpful if you need to navigate
to a different path/folder that
contains audio files.
2. Select an audio file. When
highlighted, you can:
●
Tap
tap
II
to play the audio clip, or
to pause.
●
Tap the file to insert it in the
MMS message.
●
Tap
to quit selection and
return to your MMS message.
128 JS750
NOTE To record a new audio clip and
add it to your MMS message, tap
. The Record pop-up window
opens. Tap Record
to start
recording, and Stop
to end
the recording. Tap Play
to
listen to the recorded audio clip,
then tap Record Select . The new
audio clip is then inserted to the
MMS message.
Viewing MMS messages
It is easy to view a received
multimedia message.
1. From the Today Screen, tap
message.
2. Tap the received MMS message.
3. Tap Download to download the
message, if it hasn't already been
downloaded.
Synchronizing Outlook email
with your computer
If you have installed the
synchronization software on your
computer and created a partnership
with your phone, then your phone
is ready to send and receive
Outlook email.
If you have not yet installed the
synchronization software nor created
a partnership, do so by following the
procedures in Chapter 5.
TIP
To set up your company email
account so that you can access
Outlook email messages
wirelessly, you must set up your
phone to synchronize via an overthe-air connection with your
company’s Exchange Server. For
more information about
synchronizing with your company
email server, see Chapter 7.
JS750 129
Chapter 7 Working With Company Email and
Meeting Appointments
7.1 Synchronizing with the If you have not synchronized your
phone with your computer, follow
Exchange Server
To keep up-to-date with your
company email messages and
meeting schedules while you’re out
of the office, you can connect your
phone to the Internet through Wi-Fi
or a data connection and
synchronize with your company’s
Exchange Server.
Setting up an Exchange
Server connection
Before you can synchronize or
access information on the Exchange
Server, you need to set up an
Exchange Server connection on
your phone. You need to get the
Exchange Server name (must be
Outlook Web Access server name),
domain name, user name, and the
password that you use at work from
your network administrator and
enter them on your phone.
NOTE You can set up an Outlook email
account that synchronizes with
the Exchange Server on the Today
Screen e-mail panel using Mail
Setup. See “Email” in Chapter 3
for details.
130 JS750
these steps to set up an Exchange
Server connection.
1. Press the Start Key
, tap
Email
, then tap Setup Email.
2. Enter the E-mail address and
Password for the email account
and select the Save password
option. Tap Next .
3. Clear the checkbox Try to get email settings automatically from
the Internet and tap Next .
4. In Select e-mail provider box,
tap Drop-down
, then tap
Exchange server and tap Next .
5. Tap
Next
again.
6. Select the checkbox Attempt to
detect Exchange Server Settings
automatically and tap Next .
7. Enter the Domain name and tap
Next .
8. In Server address, enter the
Exchange Server address and tap
Next .
9. Select the items that you want to
sync with the Exchange Server.
TIPS
• To change synchronization
settings of an information item,
for example, E-mail, select the
item, then tap Settings.
• To change the rules for
resolving synchronization
conflicts, tap Menu , then tap
Advanced.
10. Tap Finish.
NOTES • If you synchronized email
messages with your computer
before, open ActiveSync on
your phone, then tap Menu ,
then tap Add Server Source to
set up an Exchange Server
connection. When prompted to
select information types for
synchronization, you must first
clear the E-mail check box under
the Windows PC item before
you can select E-mail under
Exchange Server.
Starting synchronization
Before you start synchronizing with
the Exchange Server, make sure your
phone has been set up with a Wi-Fi
or data connection to the Internet
so that you can synchronize overthe-air. For more information about
connections, see Chapter 8.
After you finish setting up an
Exchange Server connection, your
phone automatically starts
synchronization.
To manually start synchronization,
, scroll the
press the Start Key
screen up, tap ActiveSync
, then
tap Sync.
NOTE If you connect your phone to
your office computer via a USB or
Bluetooth connection, you can
use this connection to the
computer to “pass through” to
the network and download
Outlook email messages and
other information to your phone.
• To change Exchange Server
settings, open ActiveSync on
your phone, and then tap
Menu , then tap Configure
Server.
JS750 131
Working With Company Email and Meeting Appointments
7.2 Working With
Company Email
Messages
Your phone gives you instant access
to your company email messages
and lets you manage your messages
easier. Direct Push, Fetch Mail,
Remote email search, and email flags
are just some of the tools you can
use to manage your email messages.
NOTE Some messaging features depend
on the Microsoft Exchange Server
version used in your company.
Check with your network
administrator for the availability of
these features.
Automatic synchronization
through Direct Push
Direct Push technology (push email
feature) enables you to receive new
email messages on your phone as
soon as they arrive in your Inbox on
the Exchange Server. Items such as
contacts, calendar and tasks are
also immediately updated onto your
phone when these items have been
changed or new entries have been
added on the Exchange Server. To
make Direct Push work, you need to
have a Wi-Fi or data connection on
your phone.
132 JS750
You need to perform a full
synchronization between your
phone and the Exchange Server
before Direct Push can be enabled.
REQUIREMENT
The Direct Push feature works for
your phone only if your company
is using Microsoft Exchange
Server 2003 Service Pack 2
(SP2) with Exchange ActiveSync
or later.
To turn on Direct Push in
ActiveSync
1. Press the Start Key
, scroll
the screen up, tap ActiveSync
, tap Menu , then tap
Schedule.
2. Select As items arrive in the Peak
times and Off-peak times boxes.
NOTE When Direct Push is off, you need
to manually retrieve your email
messages.
Scheduled synchronization
If you do not want to use Direct
Push, you can set a regular schedule
for synchronizing Outlook email and
information.
1. In ActiveSync on your phone, tap
Menu , then tap Schedule.
2. Select from the available options
to set the synchronization
schedule.
TIP
You can select a shorter interval
in the Peak times box and a
longer interval in the Off-peak
times box, so that your email
messages are synchronized more
frequently when you are working.
To set the days and hours that
make up your peak and off-peak
times, tap the peak times link at
the bottom of the screen.
Instant download through
Fetch Mail
The Fetch Mail feature downloads
an entire email immediately without
the need for you to perform a full
Send/ Receive action. This limits the
download to just the email
message(s) that you want and helps
save data cost.
REQUIREMENT
Fetch Mail works for your phone
only if your company is using
Microsoft Exchange Server 2007
or later.
1. Press the Start Key
, tap
Email
, then tap Outlook Email.
2. Open an email message.
3. By default, only the first few
words of the message are shown.
To download the whole email,
fingerscroll to the end of the
message, then tap Get the rest
of this message.
4. Wait for the remainder of the
message body to download.
JS750 133
Working With Company Email and Meeting Appointments
NOTES • For information about changing
email sync options such as
setting the download size for
email, see "Customizing email
settings" in Chapter 6.
• When you receive an email that
contains a link to a document
such as a PDF or Microsoft
Office document located on
SharePoint or an internal file
server, you can tap the link to
view the document on your
phone. You can view the
document only if you have a
Microsoft Outlook account that
synchronizes with Microsoft
Exchange Server 2007 or later.
Exchange Server must also be
set up to allow access to
SharePoint document libraries
or internal file servers.
Searching for email messages
on the Exchange Server
You can access email messages that
are not available on your phone by
searching your Microsoft Exchange
Server mailbox. The search results
are downloaded and displayed in a
Search Results folder.
134 JS750
REQUIREMENT
Your company must be using
Microsoft Exchange Server 2007
or later.
1. Press the Start Key
, tap
Email
, then tap Outlook Email.
2. Tap
, tap Tools, then tap
Search Server....
3. In the Look for text box, enter
the search keyword.
4. Choose the date range of
messages to search from.
5. In the Look in list, specify
whether to search in the Inbox,
Sent Items, or All Folders, and
then tap Search .
TIP
To clear the search results and
return to the message list, tap
, then tap Clear Results.
Flagging your messages
Flags serve as a reminder for you to
follow-up on important issues or
requests contained in email
messages.
Flagging messages, which has been
a useful feature on desktop Outlook
E-mail, can also be done in Outlook
Mobile on your phone. You can flag
received email messages on your
phone.
REQUIREMENT
Flags are enabled only if email
messages are synchronized with
Microsoft Exchange Server 2007
or later. Flags are disabled or
hidden if email messages are
synchronized with earlier versions
of Microsoft Exchange Server.
To flag or unflag a message
1. Press the Start Key
, tap
Email
, then tap Outlook Email.
2. Select a message.
3. Tap
, then tap Follow Up and
select one of the following
options:
●
Set Flag Marks the message with
a red flag to remind you to follow
up.
●
Complete Flag Marks the
message with a check mark to
indicate that the issue or request
in the email is already completed.
●
Clear Flag Removes the flag to
unmark the message.
NOTE Email message reminders are
displayed on your phone if the
messages are flagged with
reminders and synchronized from
the Exchange Server.
7.3 Managing Meeting
Requests
When you schedule and send
meeting requests from your phone,
you can invite attendees to your
meeting and check their availability.
When you receive a meeting
request, you can reply by accepting
or declining the request. The
meeting request also clearly
indicates whether or not there are
conflicting or adjacent meetings.
REQUIREMENT
Your company must be using
Microsoft Exchange Server 2007
or later.
JS750 135
Working With Company Email and Meeting Appointments
To reply to a meeting request
1. When you receive a meeting
request email, a notification is
displayed on your phone. Open
the email.
2. Tap
to reply and accept the
meeting request, or tap
, then
tap Decline if you cannot attend
the meeting.
TIPS
• Before responding, you can
check your availability during
the time of the requested
meeting by tapping View your
calendar.
• If the time of the meeting
conflicts with your other
appointments, a “Scheduling
Conflict” status appears on top
of the email.
3. Choose whether or not to edit
your response email before
sending, then tap OK .
If you accept the meeting
request, it is automatically added
as an appointment in Calendar
on your phone.
136 JS750
7.4 Finding Contacts in the
Company Directory
In addition to having contacts on
your phone, you can access contact
information from your organization’s
Company Directory. By having overthe-air access to the Company
Directory, you can easily send email
messages and meeting requests to
anyone in your company.
REQUIREMENT
Access to the Company Directory
is available only if your
organization is running Microsoft
Exchange Server 2003 SP2 or
newer, and you have completed
your first synchronization with the
Exchange Server.
When browsing Contacts,
composing email, or creating a
meeting request
1. Synchronize with the Exchange
Server.
2. Do any of the following:
●
While browsing through your
contacts on the Contacts or
Phone panel, tap
, then tap
Company Directory.
●
In a new email message, tap the
To box (or tap
, then tap Add
Recipient), and then tap
Company Directory on the top
of the list.
●
When creating a meeting request
and selecting required and
optional attendees in Calendar,
tap Company Directory.
3. Enter a partial or full contact
name and tap Search . In the
search results list, tap a contact
to select it.
NOTE You can search for the following
information as long as that
information is included in the
Company Directory: First name,
Last name, E-mail name, Display
name, E-mail address, or Office
location.
When viewing a received
Outlook email message
1. Open a received Outlook email
message.
2. If a Search button Search
appears to the right of the
sender name in the email
message, tap this button to
search for the sender in the
Company Directory.
3. If the sender is found, the
contact details will be displayed.
You can then choose to save the
sender to your contacts, call the
sender, and more.
4. You can save a contact from the
Company Directory to your
phone by selecting the contact,
and then tapping
, then tap
Save to Contacts.
JS750 137
Chapter 8 Programs
8.1 Managing Programs
Installing a program
You can install or uninstall
additional programs. Your phone
does not allow you to uninstall most
of the preinstalled programs.
NOTE Before you purchase additional
To install a program directly on
your phone
1. If the installer is a .cab file,
directly download or copy it to
your phone.
2. On your phone, open File
Explorer and navigate to the
installer file.
programs, make sure that they are
compatible with your phone.
3. Tap the file to launch the installer.
Before you launch the program
installer, check first whether the
installer can directly run on
Windows Mobile or needs to be run
on a computer.
4. Choose whether to install the
program into the main memory
or your storage card, if you have
the storage card inserted on your
phone.
5. Wait for the installation to
complete.
NOTE You may be prompted to restart
your phone after installation is
completed.
138 JS750
To install a program from your
computer
1. If the installer is an .exe file such
as Setup.exe, most likely, the
installer needs to be run on a
computer.
Download or copy it to your
computer.
2. Connect your phone to your
computer using the USB cable,
and then double-click the
installer file on your computer to
launch the installer.
3. Follow the on-screen instructions
on your computer and your
phone to complete the
installation.
To uninstall a program
1. Press the Start Key
Settings
, tap
, then tap
2. Tap System
Remove Programs
3. From the list, select the program
you want to remove, and then
tap Remove .
JS750 139
Chapter 9 Managing Your Phone
9.1 Copying and
Managing Files
Copy files between your phone and
computer, or copy files to a storage
card installed on your phone. You
can also efficiently manage your
files and folders using File Explorer.
To copy files using Windows
Mobile Device Center or
ActiveSync
b. Right-click a folder on your
computer, and then click Paste.
4. To copy a file from your
computer to your phone:
a. Browse the folders on your
computer, right-click the file
you want to copy, and then
click Copy.
b. Right-click a folder on your
phone, and then click Paste.
1. Connect your phone to the
computer.
To manage files on your phone
using File Explorer
2. Click File Management, then tap
Browse the contents of your
device in Windows Mobile Device
Center on your computer, or click
Explore in ActiveSync on your
computer. This displays the
content of your phone in
Windows Explorer on your
computer.
File Explorer lets you browse and
manage the contents of your
phone. The root folder on the
phone is named My Device, and
contains the following folders: My
Documents, Program Files, Windows,
and more.
3. To copy a file from your phone to
your computer:
a. Browse the contents of your
phone, right-click the file you
want to copy, and then click
Copy.
140 JS750
, scroll
1. Press the Start Key
the screen up, then tap File
Explorer
2. Tap a folder or file to open it.
3. To return to an upper level folder,
tap Up .
4. To quickly delete, rename, or
copy a file, tap and hold the file,
and then tap the desired
operation on the shortcut menu.
To copy or delete multiple files,
tap and drag over the desired
files, tap and hold the selection,
and then tap an option from the
menu.
To copy files to a storage card
1. Make sure that the storage card
is properly installed on your
phone.
2. Connect the phone to your
computer using the USB cable.
3. On your computer, navigate to
the removable disk drive, and
then start copying files, as you
would on a PC, to the storage
card.
4. When finished, disconnect the
phone from your computer.
9.2 Settings on your
Phone
You can adjust the phone settings
to suit your preferences. Use the
Settings tab to adjust basic phone
settings. See “Settings” in Chapter 3
for details.
To see all available settings, press
the Start Key
, then tap
Settings
. Settings are organized
into the Personal, Connections, and
System folders.
9.3 Changing Basic
Settings
Display settings
To manually adjust the screen
brightness
By default, your phone
automatically adjusts the screen
brightness according to the ambient
lighting.
1. Press the Start Key
, tap
Settings
, tap System
then tap Backlight
2. Tap the Brightness tab.
JS750 141
Managing Your Phone
3. Clear the checkbox Enable
Luminous Sensor.
3. Move the slider to increase or
decrease the text size.
4. Adjust the brightness by
dragging the slider under On
battery power and On external
power.
4. Tap
5. Tap
OK
To automatically turn off the
screen backlight when the phone
is not in use
1. Press the Start Key
, tap
Settings
, tap System
then tap Power
2. Tap the Advanced tab.
3. Tap the checkbox next to the
power source (battery or external),
then specify the time before the
screen backlight turns off.
4. Tap
OK
To increase or decrease the size of
text on the screen
1. Press the Start Key
, tap
Settings
, tap System
scroll the screen up, then tap
Screen
2. Tap the Text Size tab.
142 JS750
OK
To re-calibrate the touch screen
The phone touch screen is calibrated
before shipment. Re-calibrate the
touch screen if it does not accurately
respond to screen taps.
1. Press the Start Key
, tap
Settings
, tap System
scroll the screen up, then tap
Screen
2. Tap the Align Screen tab.
3. Follow the on screen instructions.
Phone name
The phone name is used to identify
your phone when synchronizing
with a computer, connecting to a
network, or restoring information
from a backup.
NOTE If you sync multiple devices with
the same computer, each device
must have a unique name.
To change the phone name
1. Press the Start Key
, tap
Settings
, tap System
then tap About
2. Tap the Device ID tab.
3. Enter the Device name.
4. Tap
OK
NOTES • The phone name must begin
with a letter, consist of letters
from A to Z, numbers from 0 to
9, and cannot contain spaces.
Use the underscore character to
separate words.
• If you enroll your phone to your
company’s domain, the phone
name will be changed to be the
same as the one used to enroll
the phone.
Ringer settings
To change the ring type and
ringtone
3. Tap the drop-down menu
in
the Event box, then tap phone:
incoming call.
4. Tap the drop-down menu
in
the Ring type box, then tap the
ring type you want to set.
5. Tap the drop-down menu
in
the Ring tone box, then tap the
ringtone you want to use.
6. Tap
OK
TIPS
• You can use *.wav, *.mid, *.mp3,
*.wma, or other types of sound
files that you downloaded from
the Internet or copied from
your computer. For a complete
list of supported audio file
formats, see “Specifications” in
the Appendix.
• To use your sound files as
ringtones, copy them first to the
/My Documents/My Ringtones
folder on your phone, and then
select the sound from the Ring
tone list of your phone.
1. Press the Start Key
, tap
Settings
, then tap Sounds &
Notifications
2. Tap the Notifications tab.
JS750 143
Managing Your Phone
To choose how to be notified
about events or actions
1. Press the Start Key
, tap
Settings
, then tap Sounds &
Notifications
2. Tap the Notifications tab.
3. Tap the Sounds tab, choose how
you want to be notified by
selecting the appropriate check
boxes.
4. Tap the Notifications tab, tap
the drop-down menu
in the
Event box, then tap a ring type
and ringtone for that event or
action from the lists below.
5. Tap
OK
TIP
Turning off sound notifications
helps conserve battery power.
9.4 Using Wireless
Manager
Wireless Manager lets you easily
turn on and off the communication
features of your phone such as the
phone, Bluetooth, Wi-Fi, and data
connection.
144 JS750
, tap
1. Press the Start Key
Settings
, tap Connections
, then tap Wireless Manager
2. Tap wireless functions to turn on
or off as needed.
9.5 Using Task Manager
The Task Manager allows you to
view all currently running programs
and to stop them one by one, or all
at once.
To open Task Manager
Press the Task Manager Key
on
the right side of the phone. You can
also access the Task Manager
through the Start Menu. Press the
Start Key
> Settings
System
> Task Manager
NOTE Not all programs close completely
when you exit out of them. To
make sure that they are closed,
use the Task Manager.
9.6 Protecting Your Phone
Protecting your phone with a
password
5. Tap
You can help keep your data more
secure by requiring a password
every time the phone is turned on,
or after a timeout that you set.
To set a phone password
1. Press the Start Key
, tap
Settings
, then tap Lock
2. Tap the checkbox Prompt if
phone unused for, and then
specify the idle time before the
phone requires a password. If you
choose 0 Minutes, you will need
to input the password every time
you wake the phone up from
Sleep mode. For more
information, see “Switching to
Sleep mode” in Chapter 1.
3. In the Password type box, select
the type of password you would
like to use.
TIP
4. Enter the password in both the
Password and Confirm boxes.
If your phone is configured to
connect to a network, use a
strong alphanumeric password for
increased security.
OK
If the phone is idle for the timeout
period that you set, you will need
to enter your password to unlock
your phone. If you used a simple
PIN password, the Lock screen will
be displayed before you enter your
password.
For information, see “Using the Lock
Screen” in Chapter 1.
NOTES • To ensure that you can always
make emergency calls, do not
begin your password with the
digits of your local emergency
number.
• If you entered a hint, the hint
will be displayed after the wrong
password is entered five times.
• If you forget your password, you
can hard reset or clear the
phone memory. For more
information about hard resetting
the phone and clearing the
memory, see “Resetting Your
Phone”.
JS750 145
Managing Your Phone
Encrypting files on your
storage card
You can set your phone to encrypt
files as they are saved on the
storage card.
1. Press the Start Key
, tap
Settings
, tap System
then tap Encryption
2. Tap the checkbox Encrypt files
when placed on a storage card.
NOTES • Encrypted files can only be read
on the device that encrypted
them.
• Encrypted files are opened just
like other files, provided you are
using the device that encrypted
them. There is no separate step
for you to take to read these
files.
IMPORTANT
If Encrypt files when placed on
a storage card is enabled, backup
all files from the storage card
before using Clear Storage, hard
reset, or updating the operating
system. Otherwise you will no
longer be able to access the
encrypted files on the storage
card. To backup the files, use
ActiveSync or Windows Mobile
Device Center to transfer files
between your storage card and
computer.
146 JS750
9.7 Resetting Your Phone
Performing a soft reset
Perform a soft (normal) reset to
clear all active program memory and
shut down all active programs. This
is useful when your phone is
running slower than normal, or a
program is not performing properly.
If a soft reset is performed when
programs are running, unsaved work
is lost.
To perform a soft reset
Performing a hard reset
If a soft reset does not solve a
system problem, you can perform a
hard reset. After a hard reset, the
phone is restored to its default
settings—the way it was when you
first purchased it and turned it on.
You will lose the programs you
installed, data you entered, and
settings you customized on your
phone, and only Windows Mobile®
software and other pre-installed
programs will remain.
To perform a factory reset, press
Start
> Settings
> System
> Memory
> Tap Clear
Storage and select Factory Default
from the Clear Type drop-down
menu. Then, tap Clear .
WARNING! Your phone will be set back
to factory default settings.
Make sure that any
additional installed programs
and/or user data have been
backed up before you
perform a factory reset.
JS750 147

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Print high-res
Create Date                     : 2010:05:18 18:03:38Z
Creator                         : QuarkXPress(tm) 6.52
Modify Date                     : 2010:06:11 09:23:16-04:00
X Press Private                 : %%DocumentProcessColors: Cyan Magenta Yellow Black.%%DocumentCustomColors: (New Color 2).%%+ (PANTONE 1795 C).%%CMYKCustomColor: .984 .004 1 .247 (New Color 2).%%+ 0 .94 1 0 (PANTONE 1795 C).%%EndComments
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool                    : QuarkXPress(tm) 6.52
Metadata Date                   : 2010:06:11 09:23:16-04:00
Producer                        : QuarkXPress(tm) 6.52
Format                          : application/pdf
Title                           : Layout 1
Document ID                     : uuid:b8caf551-4c6e-4a5c-9e6e-0b13ab2fd258
Instance ID                     : uuid:a5b42b22-35e6-4e34-9203-51f06773bc9e
Page Count                      : 134

EXIF Metadata provided by EXIF.tools