LG Electronics USA L05A 850/ 1900 GSM/ GPRS/ EDGE and 850 WCDMA USB Dongle User Manual L05A Manual E

LG Electronics USA 850/ 1900 GSM/ GPRS/ EDGE and 850 WCDMA USB Dongle L05A Manual E

Users Manual

Part 15.21 statement" Change or Modifications that are not expressly approved by the manufacturer could void the user's authority to operate the equipment. “Part 15.105 statement This equipment has been tested and found to comply with the limits for a class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee that interference willnot occur in a particular installation. If this equipment does cause harmful interference or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.This device is not intended for sale in the USA.
Part 15 Class B ComplianceThis device and its accessories comply with part15 of FCC rules.Operation is subject to the following two conditions:(1) This device & its accessories may not cause harmful interference.(2) This device & its accessories must accept any interference received, including interference that may cause undesired operation. Body-worn Operation This Mobile Broadband USB Modem, model L-05A, is approved for use in normal size laptop computers only (typically with 12" or larger display screens). To comply with FCC RF exposure requirements, this modem should not be used in configurations that cannot maintain at least 5mm (approximately 0.2 inches) from users and bystanders, and 12mm (approximately 0.47 inches)from the top of the USB modem. This USB modem has been tested for compliance with FCC/IC RF exposure limits in the laptop computer(s) configurations with horizontal and vertical USB slots and can be used in laptop computers with substantially similar physical dimensions, construction, and electrical and RF characteristics. When using this USB modem in your computer, it must not be co-located or simultaneously transmit with any other radio (for example, Bluetooth or Wifi radios) in the computer. If the USB modem will be used with the mounting folder and extension cable combination, the modem must not be co-located or simultaneously transmit with any active antenna that may be located on your computer screen.��
DOCOMO W-CDMA・ GSM/GPRS SystemThank You for Purchasing the「Data Commu-nication Device L-05A」Before or while using the L-05A, be sure to thoroughly read this manual and the individual manual for other operation devices to ensure its correct use. For further information, contact the "docomo Information Center" on the back of this manual. The L-05A is designed to be your close partner. Treat it carefully at all times to ensure longterm performance.Before Using the FOMA Terminal•Because the FOMA terminal uses radio waves, it may not function in locations where it is difficult for radio waves to penetrate, such as tunnels, underground passages and some buildings in areas where radio wave signals are weak or out of the service area. Even when you are on a higher floor of a tall building or condominium and nothing blocks your view outside, the FOMA terminal may not be able to receive or transmit signals. Also communication may be interrupted even when the Antenna Indication Lamp on the FOMA terminal lights green indicating a strong signal reception with 3 antenna indication bar.•Use the FOMA terminal in ways that do not disturb others in public places, crowded locations, or quiet locations.•The FOMA terminal communicates via radio waves by converting voices into digital signals. If you move into an area where signal reception is poor, the digital signals may not be accurately decoded and what you hear may differ slightly from what was actually said.•DOCOMO is not responsible for any economic losses incurred through lost communication opportunities caused by external factors such as malfunction or failure of the FOMA terminal, or electrical outage.•The FOMA terminal can be operated in FOMA Plus-Areas and FOMA HIGH-SPEED Areas.•The FOMA terminal can be used only via the FOMA network provided by DOCOMO and DOCOMO's roaming area.•This FOMA terminal does not support i-mode functions (i-mode mail, connection to official i-mode sites or i-αppli, etc.)For Those Who Use the FOMA Terminal for the First TimeIf this is the first time for you to use the FOMA terminal, it is recommended that you read this manual in the following order to learn basic operations.1. Learning the precautions. . . . . . . . . . . . . . . . . . . . . . . P72. Learning the names of parts and functions of the FOMA terminal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P183. Inserting the FOMA terminal into a PC . . . . . . . . . . P244. Having the FOMA terminal recognized by your PC. . . P245. Setting up the FOMA terminal for communication. . . . P66The latest version of this manual can be downloaded from the DOCOMO web site.■ The URL of PDF for Instruction Manualhttp://www.nttdocomo.co.jp/english/support/manual/index.html※ The URL and the information contained in the manual are subject to change without prior notice.
1How to Read/Refer to This ManualContentsL-05A Manual is composed of『L-05A Instruction Manual∼Connection Guide∼』and 『L-05A INSTRUCTION MANUAL (included CD-ROM)』(this manual) recorded in CD-ROM.■『L-05A Instruction Manual∼Connection Guide∼』The following contents such as connection to computer, troubleshooting methods, specifications of L-05A are written.•Contents/Precautions•Before Using the FOMA Terminal•Setting up•Appendix/Troubleshooting■『L-05A INSTRUCTION MANUAL (included CD-ROM)』（this manual）Besides the above contents described in『L-05A Instruction Manual∼Connection Guide∼』, the contents of configuring communication through special application are also written.This manual is supplied with PDF. To view this manual, Adobe Reader (Version6.0 or later is recommended) is necessary.•L-05A Connection Software•DOCOMO Connection Manager•Configuring Network Manually•Overseas Use
2How to Refer to This ManualThis manual offers you the following methods to easily find a page describing functions or services you want to know about.･Please understand that「L-05A Manual」 refers to the「L-05A」as the「FOMA Terminal」.･This manual describes, some steps and screens may differ depending on your operating environment.･Reprinting all or parts of this manual is prohibited. ･Information contained in this manual is subject to change without prior notice.P141Search from the index when you know the names of functions or services.Front coverSearch functions or services from the index tabs printed on the front cover.P5Search from the contents that categorize functions.P6Search from the features when you want to use specific functions.From the IndexFrom the Tabs on the CoverFrom the ContentsFrom the Main FeaturesSee next page for detailed descriptions
3A way to find a destination page is explained with an example of installing L-05A connection software on Windows (including a driver).From the IndexP141Search or a function name or a service name as shown below. From the Index Tabs on the Front CoverFront coverSearch for the function in the order of "Front cover"→"Chapter title page"→"Target page" as shown below.P35The page describing installation of L-05A connection software on Windows (including a driver)"
4Displays a section title.Explains Operation steps※：The above page is an example.※：Screen images and illustrations contained in this manualare for reference only. They may differ from those seen forthe actual product.Useful Information or suggestions relating to an operation.A key screen for an operation step. This is an image of a screen seen on the PC. Numbers, settings or characters entered are for reference only.Index:Searching each chapter is available.
5Contents/PrecautionsContentsHow to Read/Refer to This Manual ･･････････････････ 1Contents ････････････････････････････････････････････ 5Features of the L-05A･･･････････････････････････････ 6Safety Precautions (ALWAYS FOLLOW THESE PRECAUTIONS) ･････････････････････････････････････ 7Handling and Care･････････････････････････････････ 12Purchased Product and Accessories ･･････････････ 15Before Using the FOMA Terminal17Names of Parts and FunctionsUsing FOMA CardAvailable CommunicationsConnecting FOMA Terminal with a PCSetting Up31Setting UpWindows versionMacintosh versionL-05A Connection Software49L-05A Connection SoftwareUsing Packet CommunicationUsing SMSUsing PhonebookUsing Application OptionDOCOMO Connection Manager77DOCOMO Connection ManagerWindows versionMacintosh versionConfiguring Network Manually89Configuring Dial-up Network ManuallyConducting Communication (Connecting Dial-up)Overseas Use111International Roaming Service (WORLD WING)Services Available OverseasConfirming before Using OverseasSetting the Searching Method for Available NetworksConfiguring NetworkAppendix/Trouble-shooting119AT CommandsAT Command ListTroubleshootingError MessagesWarranty and After-Sales ServiceSoftware updateMain SpecificationsExport Controls of the Product and AccessoriesIntellectual Property RightsIndex
6Contents/PrecautionsFeatures of the L-05AFOMA (Freedom Of Mobile multimedia Access) is the name of a service provided by DOCOMO based on the W-CDMA system, which is certified as one of the global standards of 3rd generation mobile communication systems (IMT-2000).■ Correspondence with the FOMA HIGH-SPEED AreaYou can enjoy high speed communication (Best effort system）at a maximum of 7.2Mbps for receiving and 5.7Mbps for sending. •The maximum speed of 7.2Mbps for receiving and 5.7Mbps for sending are theoretical values and they do not show the actual performance.•Out of High-Speed area, the maximum communication speed for receiving and sending is 384kbps.•The actual communication speed varies depending on surrounding communication conditions and network condition.•DOCOMO offers Internet connection services, such as「mopera U」. For details, visit the mopera U web sitehttp://www.mopera.net/ (Japanese only)※ The packet communication in FOMA HIGHSPEED area, the amount of send/receive data is expected to increase. Note that the communication fees may become high.■ International Roaming ServiceCommunications are available from a PC even in foreign countries that have adapted the W-CDMA (3G) network system or GPRS network.P112 ※ If you subscribed to the FOMA service after September 1, 2005, a separate subscription is not required. However, if you unsubscribed to the FOMA service subscription or canceled the service, a separate subscription is required.※ If you initially subscribed to the FOMA service before August 31, 2005, and have not subscribed to "WORLD WING", a separate subscription is required.※ This service is not available with some billing plans.■ FOMA Card InterchangeabilityThe same FOMA card can be used in more than one FOMA terminal.P19 ■ SMS FeatureAllows you to send and receive SMS by using L-05A Connection Software P54
7Contents/PrecautionsSafety Precautions (ALWAYS FOLLOW THESE PRECAUTIONS)■ Before using your FOMA terminal, read these ″Safety Precautions″carefully so that you can use it properly. After reading the safety precautions, keep this manual in a safe place for later reference.■ These precautions are intended to protect you and others around you. Read and follow them carefully to avoid injury, damage to the product or damage to property.■ The signs below indicate the levels of danger or damage that may occur if the particular precautions are not observed .■ The following symbols indicate special warnings regarding product usage.■ "Safety Precautions" are explained in the following 4 sections.General Precautions for the FOMA Terminal and FOMA Card ………………………………………………………………… 8Precautions for the FOMA Terminal ……………………… 9Precautions for the FOMA Card ………………………… 10Notes on Using near Electronic Medical Equipment …… 11This sign indicates that incorrect handling has a high possibility of causing death or serious injury. This sign indicates that incorrect handling poses a risk of causing death or serious injury.This sign indicates that incorrect handling poses a risk of causing injury or damage to the product or property. DANGERWARNINGCAUTIONDenotes things not to do (prohibition). Denotes not to disassemble.Denotes not to use where it could get wet. Denotes mandatory instructions (matters that must be complied with).Not disassemblyNot liquids
8Contents/PrecautionsGeneral Precautions for the FOMA Terminal and FOMA CardDo not use or leave the FOMA terminal and FOMA card in places with a high temperature such as in cars under the blazing sun.Deformation, malfunction heating or the deterioration of performance may result. Also, part of the case could get heated, causing bare skin burns.Do not disassemble Disassemble, remodel or solder the terminal and FOMA card. Fire, injury, electric shock or malfunction may result.Do not let FOMA terminal and FOMA card get wet. Contact with water or other liquids may cause heating, electric shock, fire, malfunction or injury. Take care not to use the terminal and FOMA card in areas where they could get wet.WARNINGDo not put the FOMA terminal or FOMA card in microwave ovens or other heating. The FOMA terminal may over heat, smoke or catch fire, or its circuit parts may burst.Do not throw the FOMA terminal or FOMA card, or subject them to severe shocks. Malfunction or fire may result.Be careful not to let electro conductive materials (metal pieces, pencil leads etc.) contact with the connector terminal. Also, make sure that these are not entered into the inside of the FOMA terminal. Fire or other malfunctions may result from a short circuit.Make sure you have the power of the computer which is connected with FOMA terminal switched off before you go near a flammable gas such as gasoline fumes.Using the terminal in such an environment may result in a fire.Not disassemblyNot liquids
9Contents/PrecautionsCAUTIONDo not place the FOMA terminal or FOMA card on unstable locations such as wobbly tables or slanted locations. The FOMA terminal or FOMA card may fall, resulting in injury or malfunction.Do not store the FOMA terminal or FOMA card in humid or dusty places, or in hot areas. Malfunction may result.If children use the FOMA terminal or FOMA card, a guardian should explain the precautions and correct operations. The guardian should also make sure that the instructions are followed during use. Injury may result.Keep out of reach of babies and infants.Accidental swallowing or injury may result.Precautions for the FOMA TerminalWARNINGDo not put the FOMA terminal in the place where it could be affected by an expanded airbag, e.g. on the dashboard. If the airbag expands, the FOMA terminal could hit you and others, causing accidents such as injury and the FOMA terminal could get malfunction or damaged.Do not place the terminal in breast or inner pocket when electronic medical equipment is near by. Using FOMA terminal closed to electronic medical equipment may result malfunction.Do not allow liquids such as water, or foreign materials such as metal pieces or flammable materials to get into the FOMA card opening in the FOMA terminal.Fire, electronic shock or malfunction may result.
10 Contents/PrecautionsTurn off the FOMA terminal in places where use is prohibited such as airplanes or hospitals.Electronic and electronic medical appliances may be adversely affected. For use inside medical facilities, make sure that you comply with their regulations.Remove FOMA terminal from the USB port in places near high-precision electronic devices or devices using weak electronic signals.The FOMA terminal may possibly cause these devices to malfunction. ※ Electronic devices that may be affected Hearing aids, implanted cardiac pacemakers, implanted defibrillators, other medical electronic devices, fire alarms, automatic doors and other automatically controlled devices.If you are using an implanted cardiac pace maker, implanted defibrillator or any other electronic medical device, consult the manufacturer or retailer of the device for advice regarding possible effects from radio waves.CAUTIONElectronic devices in some types of cars can be affected by use of the FOMA terminal. For safety's sake, do not use the FOMA terminal inside such cars.Itching, rash or eczema may be caused depending on your physical conditions or predisposition. If an abnormality occurs, stop using the FOMA terminal immediately, and then seek medical attention.Metal(chrome plating) is used to the following parts.Parts that are used: USB connectorPrecautions for the FOMA CardCAUTIONBe careful when removing the FOMA card(IC portion). Your hands or fingers may be injured.
11Contents/PrecautionsNotes on Using near Electronic Medical Equipment■The description below meets ″Guideline on the Use of Radio-communication Equipment such as Cellular Telephones - Safeguards for Electronic Medical Equipment″ by the Electromagnetic Compatibility Conference.WARNINGBe sure to adhere to the following regulations inside medical facilities.●Keep the FOMA terminal out of operating rooms, intensive care units (ICUs) or coronary care units (CCUs). ●Turn off the PC in hospital wards. ●Turn off the PC in hospital lobbies and corridors if electrical medical devices could be nearby.●If the medical facility has specific zones where use or possession of mobile terminals is prohibited, follow those regulations. ●If the function which automatically turnson the power is set, cancel the settingbefore turning off your PC.Turn off the PC in crowded trains or other public places where implanted cardiac pacemaker or defibrillator wearers could be nearby.Signals from the FOMA terminal may affect the operation of implanted cardiac pacemakers or defibrillators.If you use an implanted cardiac pacemaker or implanted defibrillator, use the mobile terminal 22cm or more away from the implanted cardiac pacemaker or implanted defibrillator. Operation of an implanted cardiac pacemaker or implanted defibrillator may be affected by radio waves.Patients using electronic medical equipment other than implanted cardiac pacemakers or implanted defibrillators (using outside medical facilities for treatment at home, etc.) should check the influence of radio waves upon the equipment by consulting the manufacturer.Operation of electronic medical equipment may be affected by radio waves.
12 Contents/PrecautionsHandling and CareGeneral Usage Guidelines■Keep the FOMA terminal away from water.The FOMA terminal and FOMA card are not waterproof. Do not use the terminal in places with high humidity such as a bath or where rain may get it wet. If you carry the card close to your body, moisture from sweat may corrode the internal parts causing a malfunction. Note that malfunctions deemed to be caused by water are not covered by the warranty, and may be impossible to repair. Since these malfunctions are not under warranty, even when repair is possible, it will be done at the user's expense.■Clean the FOMA terminal with a dry, soft cloth (Lens cleaning cloth).If the FOMA terminal is wiped with alcohol, paint thinner, benzine or detergent, the printing may disappear or color may fade.■Keep the connector contacts clean with a dry, soft cloth.Dirty contacts can result in intermittent connections.■Do not place the equipment near air conditioner outlets.Condensation may form due to rapid changes in temperature, and this may corrode internal parts and cause malfunction.■Do not place the FOMA terminal where excessive force will be applied to it.If FOMA terminal is inserted to a full bag, or placed in a pocket and sat on, its internal PCBs may be damaged or malfunction. Such damage is not covered by warranty.■Read the individual manual attached to the FOMA terminal.FOMA Terminal■Avoid using in extremely high or low temperatures.The FOMA terminal should be used within a temperature range from 5 °C to 35 °C and a humidity range from 45 % to 85 %.■FOMA terminal may affect fixed phones, televisions or radios in use nearby. Use as far as possible from such appliances.■Keep a separate record of any information stored on the FOMA terminal and store the copies in a safe location. DOCOMO assumes no responsibility for the loss of any of your data.
13Contents/Precautions■Remove the FOMA terminal from the PC when transporting. Malfunction or damage may result.■It is normal for the FOMA terminal to become warm during use. You can continue to use it even when it is warm.■Take care not to drop the FOMA terminal when removing the FOMA terminal from the carrying case.■When it is not in use, keep the FOMA terminal in its carrying case to keep the connector contacts clean.Dirty contacts may result in intermittent connections.■When putting the FOMA terminal in carrying case, keep it away from wet or high temperature place. Pay attention not to put excessive force on the FOMA terminal.Transformation, tarnish, color staining may result.FOMA Card■Do not put excessive force on the FOMA card when inserting or removing it into the FOMA terminal.■It is normal for the FOMA card to become warm during use. You can continue to use it even when it is warm.■Always keep the IC portion of the FOMA card clean.■Clean the FOMA card with a soft, dry cloth (Lens cleaning cloth).■Be sure to keep a separate note of the information registered to the FOMA terminal.DOCOMO is not responsible for any losses of registered information.■Visit DOCOMO shop to return the FOMA card for the environmental purpose.■Avoid extreme temperature.■Do not scratch, touch carelessly or short circuit the IC portion. Data loss or malfunction may result.■Do not drop or give shock to the FOMA card .Malfunction may result.■Do not bend or put heavy things on the FOMA card.Malfunction may result.■Do not insert UIM into the FOMA terminal with labels or stickers attached on.
14 Contents/PrecautionsCAUTION■Do not use the modified FOMA terminal. Using modified FOMA terminal result in violating the law of Electromagnetic Compatibility.FOMA terminal has been complied with technical standard of wireless equipment stipulated by law of Electromagnetic Compatibility. As for the proof, the technical standard compliance mark, is indicated in the inscription seal. If FOMA terminal is modified by turning the screw to the left to disassemble, technical standard compliance becomes invalid.Please do not use FOMA terminal during the time when technical standard compliance is being invalid, since you are in violation of the law of Electromagnetic Compatibility.
15Contents/PrecautionsPurchased Product and Accessories■ L-05A Terminal (With Rear Cover L13, Warranty)■ L-05A Instruction Manual∼Connection Guide∼■ Carrying Case (Sample) ■ L-05A CD-ROM•L-05A Connection Software (For Windows/Macintosh）•DOCOMO Connection Manager (For Windows/Macintosh）•L-05A INSTRUCTION MANUAL（PDF） ※ Software specifications are subject to change without prior notice. ■ USB Extension Cable (Sample)Use when "USB Extension Cable" is written in this manual.■ Mounting folder (Sample)Use when "A mounting Folder" is written in this manual.
17Before Using the FOMA TerminalNames of Parts and Functions･･･････････････････ 18Using a FOMA Card･･････････････････････････････ 19Available Communications ･･･････････････････････ 23Connecting FOMA Terminal to a PC ･････････････ 24
18 Before Using the FOMA TerminalNames of Parts and FunctionsaUSB Connector→P25Connection contacts to a PC. ※Pull out from the FOMA terminal and use.The tip part of the USB connector is able to turn 90 degree. However, only one direction is available to turn.bAntenna PartThe antenna is inside the FOMA terminal.cPWR Lamp→P19Indicates the power supply conditions.dIDLE/BUSY Lamp→P19 Indicates the FOMA terminal status. dcbaExamples of a Ex. 1:Ex. 2:
19Before Using the FOMA TerminalMode Indication Lamp※ Operation indicating lampUsing a FOMA CardThe FOMA card is an IC card that stores personal information such as your phone number. Without a FOMA card installed in the FOMA terminal, you cannot use data communication. For detailed information, refer to FOMA Card Manual.Inserting/RemovingInsertingInserting the UIM with two hands.aWhile pushing the cover in the direction of a, slide the rear cover in the direction of b. Lift the cover as shown by c.FOMA Terminal StatusaPower Indication LampbMode Indication LampWhen powered on - -Waiting to connect to the FOMA network Green GreenPacket communicationAttempting to communicate Green Blue (Flash) Communicating Green BlueSMSWhile receiving Green(Flash) GreenOpening SMS Green GreenSending SMS Green GreenPINPIN Lock Green -Waiting to unlock PIN1 Green -ababcRRear Cover
20 Before Using the FOMA TerminalbInsert the UIM into slot at the direction of arrow with the IC chip side downcFit the rear cover to the ditch of FOMA terminal at approximately 3mm from the top tip of the FOMA terminal. While pressing along direction b, slide the rear cover along direction a till hear rear cover clicked.RemovingRemove the UIM with two hands.aWhile pushing the cover in the direction of a, slide the rear cover in the direction of b. Lift the cover as shown by c.bSlide the UIM in the direction of arrow and remove it from the FOMA Card slot.IC is facedNotchFOMA card slotFOMA cardabApprox.3mmabcRear CoverFOMA card
21Before Using the FOMA TerminalcFit the rear cover to the ditch of FOMA terminal at approximately 3mm from the top tip of the FOMA terminal. While pressing along direction b, slide the rear cover along direction a till hear rear cover clicked.PIN1 CodeYou can set PIN codes (Personal Identification Number) for FOMA Card. The default setting for the PIN1 code is "0000". The PIN1 code is a 4 to 8-digit security code to be entered every time the FOMA terminal is turned on for user verification to prevent any unauthorized use by others.■ Changing the PIN1 CodeYou can change the PIN1 code to any number. To prevent any unauthorized use by third parties, change it to your own number. If you improperly enter the PIN1 code 3 times in a row, further entry is locked automatically (PIN lock), so be sure to keep a separate note of the numbers you set.•Entering PIN1 Code/ Changing PIN1 code→P70■ PIN Unblocking CodeThe PIN Unblocking Code is the number used to unblock the PIN1 code. You are notified of your PIN Unblocking Code when you purchase your FOMA terminal. Entering the Unblocking Code (8-digit) unblocks the PIN lock.If you improperly enter the Unblocking Code 10 times in a row, the FOMA card locks automatically, so be sure to keep a separate note of the number.Note•Make sure not lose the removed FOMA card.•Make sure to check the direction of FOMA card.•Be careful not to scratch FOMA card's IC parts.•Inserting FOMA card in the reverse direction may cause malfunction.•Inserting and removing FOMA card with an excessive force may cause damage to your FOMA card.•Do not remove FOMA card while FOMA terminal is inserted to a PC, it may causes damage to your FOMA card.abApprox.3mmICIf your FOMA card is set to require a PIN1 code, data communication cannot be performed until the PIN1 is entered. Start the L-05A High Speed Utility and verify the PIN1 code, or set (P69)not to verify the PIN1 code in advance.
22 Before Using the FOMA TerminalFOMA Card TypesPlease be aware that the FOMA card (Blue) has different functions from the FOMA card (Green/White) as follows:WORLD WINGWORLD WING is DOCOMO's FOMA international roaming service that provides telephone and other types of mobile communications. It allows the subscriber to use the same phone number overseas as in Japan by inserting a FOMA card(green/white) into a FOMA terminal or a mobile phone designed for overseas use.•If you subscribed to the FOMA service after September 1, 2005, a separate subscription is not required. However, if you unsubscribed to the FOMA service subscription or canceled the service, a separate subscription is required.•If you initially subscribed to the FOMA service before August 31, 2005 and have not subscribed to "WORLD WING", a separate subscription is required.•This service is not available with some billing plans. •Your FOMA card (green/white) is lost or stolen overseas, contact DOCOMO immediately and temporarily suspend your subscription. For contact information, see "docomo Information Center" on the back of this manual. Call and communication charges after the terminal was lost or stolen are still charged to you.Start up L-05A Connection SoftwareThe PIN1 code Verification screen appearsEnter PIN1 CodeIncorrect entry 3 times in a rowEnter Unblocking PIN CodeOK Incorrect entry 10 times in a rowYou can set a newPIN1 code Contact a DOCOMO shopFunction FOMA card (Blue)FOMA card (Green/White)The number of digits of a phone number that can be saved to the FOMA card PhonebookUp to 20 digits Up to 26 digitsThis terminal allows up to 20 digits.WORLD WING Not available Available
23Before Using the FOMA TerminalAvailable CommunicationsPacket CommunicationFees for this communication method are based on the amount of exchanged data. You can perform data communication at a maximum of 7.2Mbps for receiving and 5.7Mbps for transmitting by using a connection that allows FOMA communication such as 「mopera U」, one of DOCOMO's Internet connection services.※ The maximum speed of 7.2Mbps for receiving and 5.7Mbps for sending is theoretical values and does not show the actual ones. The actual communication speed depends on communication environment and network congestion.•You can perform communication using international roaming under「mopera U」•Out of High-Speed area, the maximum communication speed for receiving and sending is 384kbps.•The communication speed varies depending on the access point and radio wave status.•The communication speed varies depending on the access point under international roaming.•Use the「DOCOMO Connection Manager」in the CD-ROM to check the approximate number of transmission bytes and charges under the communication.Note•Communication fees become high when performing communications with large amount of data such as browsing websites with many graphics or downloading data.•Data communication fees under international roaming differ from those in Japan.•FOMA terminal does not support 64K data communication.•This FOMA terminal does not support Remote Wakeup.•This FOMA terminal does not support FAX communication.
24 Before Using the FOMA TerminalUsage Notes■ Internet service provider feesFees to an Internet service provider may be required to connect to the Internet. These fees are added to the FOMA service fees and are paid to your Internet service provider directly. For details on connection fees, contact your Internet service provider. You can subscribe to such as「mopera U」, one of DOCOMO's Internet connection services. Charge for subscribing 「mopera U」 is required.For service and connection/settings of 「mopera」, visit the「mopera」 web site.http://www.mopera.net/mopera/index.html (Japanese only)■ User authentication to access networksDepending on the access point, user authentication (ID and password) may be required to connect. If required, enter the ID and password from the dial-up network. The ID and password will be provided by the network administrator of your Internet service provider or the access point. For details, contact your provider or access point network administrator.■ Requirements for packet communicationThe following conditions must be met to perform communications using the FOMA terminal. However, a connection may not be established if traffic is heavy at the base station or if radio signals are weak.•The FOMA terminal must be in a FOMA network or DOCOMO's roaming service area.•The access point corresponds to the FOMA packet communication.Connecting FOMA Terminal to a PCWhen connecting FOMA terminal with computer for the first time, it is required to install L-05A connection software (including a driver).For installing L-05A connection software, refer to the followings.•For Windows: "Preparation for using L-05A" (P35)•For Macintosh: "Preparation for using L-05A" (P42)InsertingaTurn on a PCbConnecting the FOMA terminal with a PC■When using a mounting folder and a USB extension cable•Use a mounting folder and a USB extension cable to fix on the top of a PC
25Before Using the FOMA TerminalaPull out the projection part of USB connector 180 degree by fingertipbHold the connector part of USB extension cable and insert into the USB connector near the FOMA terminal along arrow direction cPut the FOMA terminal between the mounting folder and fix on the top of the PCdHold the connector part of USB cable and insert into PC USB port along arrow directionProjection partUSB connectorUSB extension cableMounting folderPCUSB port USB extension cable
26 Before Using the FOMA Terminal■When connecting with a PC directly•Insert the FOMA terminal into a PC USB port and use it directly.•The USB connector of FOMA terminal is able to turn 90 degree complying to directions of USB portaPull out the projection part of USB connector 90 degree by fingertipbThe FOMA terminal body turn the tip part of USB connector 90 degree as shown in the illustrationcInsert the USB connector of FOMA terminal into a PC USB port•It is available to use without turning USB connector 90 degree as the above-mentioned procedure b.•Projection partUSB connectorUSB connectorNote•Refrain from turning the FOMA terminal after inserting USBconnector into PC USB port. Malfunction or damage may result when subject the FOMAterminal to severe shocks due to carelessness.USB portUSB connectorUSB port
27Before Using the FOMA TerminalcStart communication connectingRemovingaEnd data communication•If the L-05A connection software/DOCOMO connection manager is already running, exit the L-05A connection software/DOCOMO connection manager. Verify that data connection is disconnected.bRemove the FOMA terminal■When using a mounting folder and a USB extension cableaHold the connector part of a USB extension cable and pull out the FOMA terminal from PC USB port along arrow directionNote•Confirm whether power indication lamp changes to red and mode indication lamp changes to green.•Using "L-05A connection software"→P49•Using "DOCOMO connection manager"→P77•Configuring manually (OS Standard)→P89Power Indication lampMode Indication LampUSB port USB extension cable
28 Before Using the FOMA TerminalbRemove the FOMA terminal along with the mounting folder from the top of the PC. Remove the mounting folder from the FOMA terminalcHold the connector part of the USB extension cable and pull out from the USB connector near the FOMA terminal along arrow directiondPack the USB connector into the FOMA terminal■When connecting to a PC directlyaHold the USB connector part of FOMA terminal. Pull outthe FOMA terminal straightly from PC USB portMounting folderPCUSB connectorUSB extension cableUSBconnectorUSB portUSB connector
29Before Using the FOMA TerminalbTurn the tip part of the USB connector 90 degree as shown in the illustrationcPack the USB connector into FOMA terminalCaution•If you force to remove FOMA terminal and pull out the USB extension cable, this may result malfunction.•Removing FOMA terminal from USB connector during data communication may suspend data communication and result malfunction or data losses.USB connectorUSB connector
31Setting upSetting up ･･･････････････････････････････････････ 32Windows Version ････････････････････････････････ 35Macintosh Version ･･･････････････････････････････ 42
32 Setting upSetting up■ Data communication with L-05A"Communication configuration file (Driver)" and "L-05A connection software" are required to install for a PC to recognize the FOMA terminal. "Communication configuration file (Driver)" will be installed along with "L-05A connection software".Although data communication is available with only L-05A connection software, if necessary using it after installing DOCOMO connection manager in addition is also available.Data communication is also available based on configuring manually after installing L-05A connection software.■ Installation of L-05A connection softwareSince L-05A has zero installation, when connecting the FOMA terminal to a PC for the first time, "L-05A connection software" installation screen appears automatically. "Zero installation" is supported by the PC with Windows OS in it. If zero installation works improperly, install L-05A connection software with the included CD-ROM.In addition, although Macintosh does not support the zero installation feature, installation continues through the CD-ROM icon appears when connecting the FOMA terminal to a PC.The procedure of setting up is described on the next page.
33Setting upWork Flow of Setting upConnecting the FOMA terminal with a PC・ Windows VersionP35 ・ Macintosh VersionP42Preparing the included CD-ROM・ Windows VersionP38 ・ Macintosh VersionP45Installing L-05A connection software (Driver)Confirmation after Setup・ Windows VersionP39/・ Macintosh VersionP45Operation configurations of L-05A connection softwareP66Communication connection with L-05A connection softwareP50Installing DOCOMO connection manager・ Windows VersionP79 ・ Macintosh VersionP83Operatino configuration/communication connectionwith DOCOMO connection manager『DOCOMO connection manager manual』Communication configuring manuallyP90Communication configuring manually with OS functionP109Using L-05A connection softwareUsing DOCOMO connection managerConfiguring manually(Only Windows)
34 Setting upOperating EnvironmentsUsing this FOMA terminal under the following operational environments.※1 DOCOMO does not guarantee the operation under the supported OS of the OS is changed through update.※2 Required memory or available hard disk space may vary depending on the system environment of a PC.※3 Only Mac with CPU made by Intel Corporation is available.For latest information of operation environment, visit DOCOMO's "international web site"Item RequirementPC Main Unit•Available CD-ROM drive to use from PC-AT compatible.•USB port (Comply with Universal Serial Bus Specification Rev1.1/2.0)•DOCOMO is not responsible for any incompatibility of the operation performed through the USB Hub (including USB port available from the monitor, keyboard, etc.)•Display resolution of 800×600 pixels, High Color (65.536) or higher is recommended.OS※1Windows 2000 SP4 or later (Japanese versions)Windows XP SP2 or later (Japanese versions)Windows Vista SP1 or later (Japanese versions)Mac OS X 10.4.11 (Japanese versions)※3Mac OS X 10.5.6 (Japanese versions)※3Required Memory※2Windows 2000 : 64Mbytes or moreWindows XP : 128Mbytes or moreWindows Vista : 512Mbytes or moreMac OS X 10.4.11：512Mbytes or moreMac OS X 10.5.6：512Mbytes or moreHard Disk Space※2 50Mbytes or more available spaceNote•The software may not work depending on the operating system environment. DOCOMO does not guarantee any operation other than the environment operation described on the left side.
35Setting upWindows VersionThe L-05A connection software only need to be installed when you connect the FOMA terminal to your PC for the first time.Preparation for Using L-05ASetting Zero Installation (Auto)■ For Windows VistaaConnect the FOMA terminal with a PCThe setup screen of L-05A connection software is automatically displayed by zero installation."自動再生" screen will be displayed depending on setting.If the screen is displayed, check "ソフトウェアとゲームに対しては常に次の動作を行う" and select "Launcher.exeの実行"np※ When the Setting up screen of L-05A connection software is not automatically displayed, install with the included CD-ROM (P38)Note•Do not remove the FOMA terminal while installing.•Installation may take several minutes depending on the PC you use. •Do not install or uninstall during data communication. •When installing, make sure to install from the account with PC supervisor privileges. An error will occur during installation if you install from the account without these privileges. •For details on setting up PC supervisor privileges, contact your computer manufacturer or Microsoft Corporation.
36 Setting upbClick "許可(Allow)" on "ユーザーアカウント制御(User account control)" screen■For Windows XP/2000•Because "ユーザーアカウント制御(User account control)" screen is not displayed, follow the next stepcClick "次へ(Next)"dClick "同意する (I Agree)"Installation starts.eClick "次へ(Next)"
37Setting upfClick [OK]gClick "完了(Finish)"Installation of L-05A communication configuration file (Driver) continues.hConfirm whether the FOMA terminal is recognized by PCOn the lower right side of task tray, "デバイスドライバソフトウェアをインストールしています(Device driver software is being installed)" message is displayed, and the FOMA terminal is recognized automatically.If the FOMA terminal is recognized properly, "デバイスを使用する準備ができました(The device is ready for use)" message is displayed.
38 Setting up■For Windows XP• On the lower right side of task tray, "新しいハードウェアが見つかりました。 (A new hardware has been found.)" message is displayed, and the FOMA terminal is recognized automatically.• If the FOMA terminal is recognized properly, "新しいハードウェアがインストールされ、使用準備ができました。(A new hardware has been installed and ready for use.)" message is displayed.■For Windows 2000• The warning screen of removing device is displayed which has nothing to do with using continually.• "新しいハードウェアが見つかりました(A new hardware has been found.)" message is displayed, and the FOMA terminal is recognized automatically.Setting Manually (CD)■ For Windows VistaaAfter starting a PCInsert the included CD-ROM into the PCb"スタート(Start)""すべてのプログラム(All programs)""アクセサリ(Accessory)"Click "ファイル名を指定して実行(Specify a file name and run)"■For Windows XP/2000Click [スタート(Start)] 「ファイル名を指定して実行(Specify a file)」cEnter "<CD-ROMドライブ名>:¥Windows¥L-05A 接続ソフト¥StartCD.exe" in "名前(Name)"  Click "OK""自動再生" screen will be displayed depending on setting.If the screen is displayed, check "ソフトウェアとゲームに対しては常に次の動作を行う" and select "Launcher.exeの実行"dPerform the same operations as those after step 2 or later on "Setting Zero Installation (Auto) (→P36)"
39Setting upConfirmation after InstallationConfirming L-05A Connection SoftwareaDouble click L-05A connection software iconWhen the following screen is displayed, the confirmation of installation finishes.Confirming the Installed L-05A Configuration File(Drivers)Confirm whether L-05A Communication Configuration File (Drivers) is set in a PC.■ For Windows VistaaClick "スタート(Start)""コントロールパネル(Control panel)""システムとメンテナンス(System and maintenance)""デバイス マネージャ(Device manager)""続行(Continue)"■For Windows XPClick "スタート(Start)""コントロールパネル(Control panel)""パフォーマンスとメンテナンス(Performance and maintenance)""システム(System)""デバイス マネージャ(Device manager)" of "ハードウェア(Hardware)" tab■For Windows 2000 Click "スタート(Start)""設定(Settings)""コントロールパネル(Control panel)""システム(System)""デバイス マネージャ(Device manager)" of "ハードウェア(Hardware)" tab
40 Setting upbClick each device display to confirm the driver name installed•Confirm whether the driver name is displayed below "ポート(COM とLPT)(Port (COM and LPT))", "モデム(Modem)"•COM port number differs depending on user and PC.Device name Driver namePort(COM and LPT)FOMA L05A USB Serial1 Device FOMA L05A USB Serial2 Device Modem FOMA L05ANote•If FOMA terminal is not recognized through the PC's USB port, try other available USB port. FOMA terminal may not be recognized properly with some USB port of PC.•When communicating data with L-05A connection software, application operation of L-05A is required.→P66•When communicating data with DOCOMO connection manager without L-05A connection software, installation of DOCOMO connection manager is required.→P79•When communicating data with neither L-05A connection software nor DOCOMO connection manager, configure it manually.→P90
41Setting upUninstalling L-05A Connection Software(including a driver)•Before uninstalling, remove the FOMA terminal from the PC.•When uninstalling, make sure to install from the account with PC supervisor privileges. •Make sure to save important data in FOMA card. Uninstallation will results in data loss when Phonebook or SMS data is saved in PC.■ For Windows Vistaa "スタート(Start)""すべてのプログラム (All programs)""L-05A接続ソフト (L-05A connection software)"Click "Uninstall"■For Windows XP•"スタート (Start)""すべてのプログラム (All programs)""L-05A 接続ソフト(L-05A connection software)"Click "Uninstall"■For Windows 2000•"スタート (Start)""プログラム (Program)""L-05A 接続ソフト(L-05A connection software)"Click "Uninstall"bClick "許可(Allow)" on "ユーザーアカウント制御 (User account control)" screenIf "キャンセル(Cancel)" is clicked, uninstallation will be stopped.■For Windows XP/2000•Since "ユーザーアカウント制御 (User account control)" screen is not displayed, follow the next procedure.cClick "アンインストール (Uninstall)"dClick [OK]
42 Setting upeClick [OK]fClick "完了 (Finish)"Uninstallation finishes.Macintosh VersionWhen installing L-05A connection software, make sure to finish "ドコモ コネクションマネージャ (DOCOMO connection manager)" first.Preparation for Using L-05ASetting Zero Installation (Auto)aConnect the FOMA terminal with a MacCD-ROM icon is displayed on the desktop.bDouble click the CD-ROM iconNote•Do not remove the FOMA terminal while installing.•When installing, make sure to install from the account with PC supervisor privileges.
43Setting upcDouble click "L-05A 接続ソフト インストーラー.mpkg (L-05A connection software installer.mpkg)"dClick "続ける (Continue)"eClick "続ける (Continue)"fConfirm "使用許諾契約 (The license agreement)". If agree with the content, click "同意する (I Agree)"
44 Setting upgClick "インストール (Install)"h Enter administrator passwordClick "OK"iClick "インストールを続ける(Continue installing)"jClick "再起動(Restart)"Mac restarts. Installation finishes.
45Setting upSetting Manually (CD)aStart MacInsert the CD-ROM into MacCD-ROM icon on desktop appears.bDouble click CD-ROM icon"Mac""L-05A connection software"cFor subsequent steps, operate the same procedures as those after procedure 3 in "Set Zero Installation (Auto)" (→P43)Confirmation after InstallationConfirming L-05A Connection SoftwareaDouble click L-05A connection software iconWhen the following screen is displayed, the confirmation of installation finishes.Note•When communicating data with L-05A connection software, setting application operations of L-05A is required.→P66•When communicating data with DOCOMO connection manager without L-05A connection software, installation of DOCOMO connection manager is required.→P79
46 Setting upUninstalling L-05A Connection Software (including a driver)•Before uninstalling, remove the FOMA terminal from the Mac.•When uninstalling, make sure to install from the account with PC supervisor privileges.•Make sure to save important data in FOMA card. Uninstallation will results in data loss when Phonebook or SMS data is saved in PC.•End "DOCOMO connection manager" when uninstalling L-05A connection software.aInsert the included CD-ROM into a MacCD-ROM icon is displayed on the desktop.bDouble click the CD-ROM iconcDouble click "Mac"dDouble click "L-05A接続ソフト (L-05A connection software)"eDouble click "アンインストーラ.app (Uninstaller.app)"
47Setting upfClick "アンインストール(Uninstall)" gEnter administrator password  Click "OK"hConfirm whether the FOMA terminal is connected to USB port before restartingiClick "再起動(Restart)"Mac restarts. Uninstallation finishes.
49L-05A Connection SoftwareL-05A Connection Software ･････････････････････ 50Using Packet Communication ･･･････････････････ 53Using SMS ･･･････････････････････････････････････ 54Using Phonebook ････････････････････････････････ 63Using Application Option･････････････････････････ 66L-05A connection software is available to use on either Windows or Macintosh. Despite the display images of Windows version and Macintosh version are a little different, icons on the screen and available functions are same. Please note that in this chapter the descriptions are based on screen images of Windows.
50 L-05A Connection SoftwareL-05A Connection SoftwareThe L-05A connection software allows you to use packet communication/SMS/Phonebook.Launching and Exiting Connection Software (For Windows)Launching•Double click created on the desktop.Exiting•Click located on the top of main application screen.Launching and Exiting Connection Software (For Macintosh)If connect with L-05A, it will be recognized as a CD-ROM first. For recognizing as a modem, drug the CD-ROM icon into trash.Launching•Launch "Finder" "アプリケーション(Application)" "L-05A 接続ソフト.app (L-05A connection software.app)"Exiting•Menu bar "L-05A 接続ソフト(L-05A connection software)"  "L-05A 接続ソフトを終了(Quit L-05A connection software)"•Using Packet Communication→P53Allows you to easily use packet communication.•Using SMS→P54Features of composing messages, Inbox, Outbox, Drafts box and Saving to FOMA card are available.•Using Phonebook→P63Features of composing messages, adding and deleting new group, transferring group, adding new item, modifying user, delection are available.•Using Application Option→P66Confirm the amount of packet communication data usage, configure internet option, configure FOMA card, enter PIN1 code, configure the connection type (PDP), reset FOMA terminal, configure network are available.Note•Data of L-05A connection software will be saved in PC if nodestination is specified.
51L-05A Connection SoftwareMain Application ScreenaList of icon indicating FOMA terminal status※1 W-CDMA (3G)A third generation mobile communication network complying with 3GPP Global standards. 3Gpp means 3rd Generation Partnership Project. The local standardization organization established for the development of common technical specifications related to 3rd Generation Mobile Communication Systems (IMT-2000).※2 HSDPA (Short for High Speed Downlink Packet Access)HSUPA (Short for High Speed Uplink Packet Access)A high speed type of W-CDMA data communication. It is called "3.5G" since it is the improvement version of 3rd generation (3G) cell phone (W-CDMA).※3 GSM (Short for Global System for Mobile Communication)The second generation mobile communication network in a digital communication system that is most widely used around the world.※4 GPRS (Short for General Packet Radio Service)GPRS is the 2.5 generation mobile communication system that enables highspeed packet communication using GSM.Signal reception level   Strong ← → WeakNetwork type W-CDMA※1, HSDPA※2, HSUPA※2, GSM※3/GPRS※4abecdf(Out of service area) In no signal reception areaInternet ConnectionInternational RoamingUnopened message found
52 L-05A Connection SoftwarebStatus／Message display area•FOMA terminal,warning messages, operation status, network name.•The information of currently accessed network operator is displayed when "network information" is set to "display"→P116cButtons for connecting and disconnecting to Internet•Click this button when connecting or disconnecting Internet.dData communication information display area•During connecting to Internet, connection time and amount of loaded data are displayed.eOperation button•Buttons are available for SMS, Phonebook, Settings and Information.fCurrent time/data display area•Current date and time are displayed.•Time is set conformable to PC time. Confirming My NumberClick from the main application screen, and then you will see the following messages displayed.: SMS（P54）: 電話帳 (Phonebook)（P63）: 設定(Settings)（P66）:インフォメーション(Information)（P51）My numberVersion information
53L-05A Connection SoftwareUsing Packet CommunicationYou can use packet communication if click from the main application screen.Start Packet CommunicationaClick from the main application screen•Displays connection time, amount of downloaded data connection status icon .Disconnecting to Packet CommunicationaClick from the main application screen•Packet communication will be disconnected after the messages displayed "切断しています。(Connection is being disconnected)".Note•The packet communication may be automatically disconnected depending on the network status or location.•In packet communication, fees apply on the amount of sent/received data. Note that the communication fees may become high if you perform heavy communications such as by browsing websites which include large multimediacontents or if you download a lot of data.•Data communication fees under international roaming differ from those in Japan.
54 L-05A Connection SoftwareUsing SMSAllows you to use various SMS features if click from the main application screen.•Maximum number of SMS stored in PC is 1000. Depending on PC's available hard disk space, number may differ. (Excluding FOMA card SMS box)When Receiving SMSThe following screen appears when receiving SMS.aClick Composing SMSaClick from the SMS application screenbEnter the SMS from the SMS composing screen•SMS can be entered up to 70 characters (English alphabet & numeric characters can be entered up to 160 characters)：Composing SMS：Outbox：Inbox：Drafts box：FOMA card SMS boxComposing SMSTransferring to phonebookEntering receiver's phone numberMessage/receiversreset, sending SMS
55L-05A Connection SoftwarecEnter the receiver's phone number•Enter the receiver's phone number by clicking the input or click to display phonebook and decide a receiver.•If you edit SMS or receiver, enter directly in SMS edit screen or phone number field to modify.dClick •SMS are being sent.•Result of sending SMS.Note•You will be prompted whether you want to save the SMS to Drafts box or not, when moving to other applications or when failure incurred in transmission. If you click , the SMS will be saved to Drafts box. If you click , the SMS will not be saved to Drafts box.•Setting "SMS一括拒否(Multi-refuse SMS)"By using the following AT command, SMS is set in terminal software.For details of terminal software, refer to "通信の手動設定(Configuring Network Manually)" P90SMS refuse: AT+CUSD=1,"*141*1#",15Unlock SMS refuse: AT+CUSD=1,"*141#",15
56 L-05A Connection SoftwareInbox•Allows you to store SMS to Inbox.Confirming SMS from InboxaClick from the SMS application screen•Displays the list of received SMS.bSelect and confirm the SMS from the SMS listReplying and Forwarding SMS from InboxaClick from SMS application screenbSelect the reply/forward from Inbox list Click "返信(Reply)/転送(Forward)" menu is displayedcClick Note•The SMS status becomes opened once you click the received SMS.: SMS opened: SMS unopenedReceiver phone numberBrowse phonebook application screen → P64•"返信(Reply)"： Receiver phone number is automatically entered and move to the SMS composing screen.•"転送(Forward)"： SMS to be sent are automatically entered, and move to the SMS composing screen. The receiver phone number is required to enter.
57L-05A Connection SoftwareCopying Inbox SMS to FOMA CardaClick from SMS application screenbSelect the SMS and right-clickClick "FOMAカードに保存(Save to FOMA card)"•"FOMAカードに保存(Save to FOMA card)": Copy the received SMS of PC to FOMA card.•You can copy 20 SMS in total including sent and received to your FOMA card.Deleting SMS from InboxaClick from SMS application screenbSelect the SMS to delete from the list of InboxClick "削除(Delete)""全削除(Delete all)" menu displayedThe message for confirming is displayed.cClick Outbox•Allows you to store SMS in Outbox.Confirming SMS from OutboxaClick from SMS application screen•Displays the list of sent SMS.bSelect and confirm the SMS from the list•"削除(Delete)"： Delete the selected SMS.•"全削除(Delete all)"： Delete all SMS： Sent SMSReceiver's phone numberBrowse phonebook application screen → P64
58 L-05A Connection SoftwareEditing SMS from OutboxaClick from SMS application screenbSelect the SMS to send from the list of OutboxClick •SMS composing screen•You will be prompted with SMS composing screen as soon as the receiver phone number and SMS are entered.•You can add or edit SMS and receiver phone number.cClick Copying SMS from Inbox to FOMA CardaClick from SMS application screenbSelect the SMS and right clickClick "FOMAカードに保存(Save to FOMA card)"•"FOMAカードに保存(Save to FOMA card)"： Copy sent SMS stored in a PC to FOMA card.•Up to 20 received and sent SMS can be stored in FOMA card.Note•The information of time will not be saved when SMS are copied from Inbox to FOMA card.
59L-05A Connection SoftwareDeleting SMS from OutboxaClick from SMS application screenbSelect the SMS to delete from the list of InboxClick "削除(Delete)""全削除(Delete all)" menu is displayed.The message for confirming is displayed.cClick Drafts Box•Allows you store temporary SMS in Drafts box.Confirming SMS from Drafts boxaClick from SMS application screen•The list of SMS from Drafts box will be displayed.bSelect and confirm the SMS from the list of Drafts box•"削除(Delete)"： Delete the selected SMS.•"全削除(Delete all)"： Delete all SMS.
60 L-05A Connection SoftwareEditing from Drafts BoxaClick from SMS application screenbSelect the SMS to edit from the list of drafts boxClick •You will be prompted with SMS composing screen as soon as the receiver's phone number and SMS are entered.•You can add or edit SMS and receiver's phone number.cClick Deleting SMS from Drafts boxaClick from SMS application screenbSelect the SMS to delete from the list of drafts boxClick "削除(Delete)" and "全削除 (Delete all)" menu is displayed.The message for confirming is displayed.cClick FOMA Card SMS Box•Allows you to save SMS copied from Inbox or Outbox are to FOMA card SMS box.•Up to 20 received and sent SMS can be stored in FOMA card.Confirming SMS from FOMA Card SMS BoxaClick from SMS application screen•The list of SMS from Drafts box will be displayed.bSelect and confirm the SMS from the FOMA card SMS box•"削除(Delete)"： Delete the selected SMS.•"全削除(Delete all)"： Delete all SMS.:Received SMS(SMS unopened):Received SMS(SMS opened):Sent SMS
61L-05A Connection SoftwareReplying and Forwarding SMS from FOMA CardSMS BoxaClick from SMS application screenbSelect the SMS to reply/forward from the list of FOMA card SMS boxClick "返信(Reply)""転送(Forward)" menu is displayed.cClick Deleting SMS from FOMA Card SMS boxaClick from SMS application screenbSelect the SMS to delete from the list of FOMA card SMS boxClick "削除(Delete)""全削除(Delete all)" menu is displayed.The message for confirming is displayed.cClick •"返信(Reply)"： You will be prompted with SMS composing screen as soon as the receiptor's phone number and SMS are entered.•"転送(Forward)"： The SMS to be sent will be automatically entered, and move to SMS composing screen. The receiver's phone number is required to enter.•"削除(Delete)"： Delete the selected SMS.•"全削除(Delete all)"： Delete all SMS.
62 L-05A Connection SoftwareSaving SMS in FOMA Card SMS Box to PCaClick from SMS application screenbSelect the SMS to save from the list of FOMA card SMS boxRight clickcClick "パソコンに保存(Save to PC)"dClick Sending SMS from PhonebookaSelect the phonebook record to sendbClick from the phonebook application•Receiver's phone number is automatically entered and move to the SMS composing screen.cClick dClick Note•Refert to "SMS作成する (Composing SMS)" to enter the SMS.（P54）
63L-05A Connection SoftwareSending SMS from Japan to Overseas■SMS•You can use the same mobile phone number overseas as is used in Japan.•If receiptor's terminal is FOMA terminal Enter "+", and "country code", in front of receiptor's phone number, if receiptor is subscribed to overseas carrier other than NTT DOCOMO. Also, enter the "010" "Country code" "Receiptor's mobile phone number" in order. (If receiptor's phone number starts with "0", enter the phone number without "0"•If the receiptor received unsupported characters of SMS from the sender who subscribed to other overseas carrier, the message may not be displayed properly.Using PhonebookClick allows you to use various features of phonebook.The list of stored phonebook records are displayed when Phonebook records are stored in FOMA card.•Total number of phonebook records to be stored may be different depending on PC's available hard disk space. Total number of phonebook records stored in FOMA card is maximum 50.:Phone number stored in PC:Composing SMS:Transferring group:New record:Editing record:Delete:Adding and deleting new group:Phonebook record stored in FOMA card
64 L-05A Connection SoftwareAdding Phonebook Record•Follow the steps to add new phonebook recordaClick from the Phonebook applicationbStart the following operations•You can enter Kanji, Hiragana, Katakana, English, number, character. (Full-width 10 character. Half-width 21character). You can enter the 20 character length.cClick dClick Searching Phonebook RecordaEnter the name to be searched•You can search phonebook record by entering phone number.bClick Editing Phonebook RecordaSelect the phonebook record to be editedbClick from the phonebook application•Edit phonebook record number if editing screen appears.cClick dClick •： Save entered information to phonebook.•： Not save entered information to phonebook.Select a groupEnter the name to be addedEnter the phonebook to be added•： Save entered information to phonebook.•： Not save entered information to phonebook.
65L-05A Connection SoftwareDeleting Phonebook RecordaSelect phonebook record to deletebClick from the phonebook applicationAdding New GroupaClick from the phonebook applicationbEnter the group name to be added•You can enter Kanji, Hiragana, Katakana, English,  number, character. (Full-width 20character , Half-width 20character).cClick dClick •： Delete phonebook record.•： Cancel deleting phonebook record.Note•If you have many phonebook record to delete, multi-select phonebook records by using shift or Ctrl keys from key board and then click delete button to delete the selected phonebook record.
66 L-05A Connection SoftwareDeleting Group NameaClick from the phonebook applicationbSelect the group name to be deletedcClick dClickPhonebook Record Transfering Other GroupaSelect the phonebook record to be transferredbClick from the phonebook applicationcSelect the group name to be transferreddClick •Transfer the selected phonebook record to the group you want to transfer to.Using Application OptionClick allows you to use various features of application option by clicking from the main application screen.The following s are required to connect Internet with L-05A connection software.aThe setting of provider informationRegister APN with other registration number (<cid>) on "接続方式設定(Connection type configuration)" screen. (→P72)bBasic settingConfigure "*99***<cid>#" as a dial number during packet communication on "Basic setting (Internet Option)" screen. Also configure "User name", "Passward" provided by provider if required. Based on the above preparations, the APN with registration number entered in <cid> will be connected to.Note•"デフォルト(Default)" group and "FOMAカード (FOMA card)" group can not be deleted.Note •If selecting two or more record, select records by using Shift or Ctrl keys and then click "起動(Transfer)" to collectively transfer.： Amount of downloaded data： Internet option： F O M A c a r d： Connection configuration： FOMA terminal reset： Network setup
67L-05A Connection SoftwareConfirming Packet Communication Volume•Confirms that the amount of data transmission used in packet communicationaClick from the application option screen.全体使用量(Total usage) Accumulated total data usage：Initialize total usage to zero1ヶ月使用量(Monthly usage) Monthly usage：Initialize monthly usage to zero前回の使用量 data usage of current sessionConfiguring Internet Option•Allows you to configure basic settingsfor connecting to Internet.aClick from the application option screenbStart the following operations1ヶ月使用量 (Monthly usage)前回の使用量 (Current usage)全体使用量 (Total usage) Note•The data usage displayed on the screen may differ from the actual volume of packet communication.ユーザー名 (ID)パスワード (Password)ダイヤル (Service number)設定 (Configuration)SMS センター番号(SMS center number)基本設定リセット (Basic setting reset)設定 (Configuration)
68 L-05A Connection Softwareユーザー名(ID) ID supplied from service providerパスワード(Password) The password supplied from service providerダイヤル(Service number) number of service provider※For packet communication, enter *99***<cid>. Enter the registration number of APN set in <cid>(P72).SMSセンター番号(SMS center number) ※Normally, change in setting is not necessary. Enter SMS center number when using SMS from the network operator other than DOCOMO. 設定(Configuration) Click to change setting 基本設定リセット(Basic setting reset) Click to return to basic settingcClick the applicable Configuring FOMA Card•Allows you to configure "PIN1ロック(PIN1 lock)", "PIN1解除(PIN1 unblocking)", "PIN1暗証番号変更 (PIN1code change)"aClick from the application optionNote•Click "設定(Configuration)" to renew the setting. Always remember to click when setting is changed.•You will not connect to Internet if ID, password and service number are incorrect.•SMS may not be sent or received when SMS service number has been improperly entered.•In Macintosh, input any character in user name and passward.PIN1 モードPIN1(PIN1 Mode)
69L-05A Connection SoftwareLocking PIN1•Set security to FOMA card.aSelect "PIN1ロック(PIN1 locking)" from PIN1 modebEnter the PIN1 code configured in FOMA card to "PIN1"cClick dClick Unblocking PIN1aSelect "PIN1解除(Unblocking PIN1)" from PIN modebEnter the PIN1 code configured in FOMA card to "PIN1"cClick dClick Note•When starting L-05A connection software with PIN1 locked, you need to enter PIN1 code from the screen of entering PIN1 code.You can not use FOMA terminal properly unless you enter correct PIN1 code.Note•If PIN1 unblocking code is set, you can use FOMA card information from FOMA terminal without verifying PIN1 code.
70 L-05A Connection SoftwareModifying PIN1 Code•Set the password required when unlocking or locking PIN1.•Changing PIN1 code is only available when PIN is locked.aSelect "PIN1暗証番号変更(Changing password of PIN1)" from PIN1 modebEnter the FOMA card PIN1 code to "PIN1"cEnter the PIN1 code change in "新しいPIN1コード(New PIN1 code)"dEnter the PIN1 code entered in "新しいPIN1コード (New PIN1code)" code in "再入力(Confirming New PIN 1code)"again to verifyeClick fClick PIN1 コード (PIN1 Code)PIN1 モード (PIN1 Mode)現在の PIN1 コード (Current PIN1 Code) 変更する PIN1 コード(PIN1 Code to change)変更する PIN1 コード確認(Confirming PIN1 Code to change)
71L-05A Connection SoftwareEntering PIN1 Code•When L-05A connection software is started after setting PIN1 Lock, PIN1 code input screen will appear or it is restart to reset FOMA terminal.aEnter PIN1codeEnter the 4 to 8 PIN1 codebVerify the result after entering PIN1 codeEx.1： When PIN1 code has been successfully entered.Ex.2： When PIN1 code has been improperly entered.Ex.3： When PIN1 code has been improperly entered 3times in a row.•If you improperly enter the PIN1 code 3 times in a row, the verification screen for unblocking PIN1 code will be displayed.■Unblocking locked PIN1 codeaEnter the unblocking PIN1 code to "PIN1ロック解除コード(Unblock)"bEnter the PIN1 code to "新しいPIN1コード(New PIN1 code)" to changecEnter the PIN1 entered in "新しいPIN1コード(New PIN1 code)" in "再入力(confirming New PIN1 code)" to confirmdClick
72 L-05A Connection SoftwareConfiguring Connection type (PDP Type)•Configure connection type.aClick from Internet Option screenbStart the following operationsa登録番号(Registration Number(cid))The registration numbers are available from cid1 to cid 10 in FOMA terminal. To connect to a provider other than「mopera U」or 「mopera」, you can set the access point name (APN) to any of cid2 or cid4 to cid10.b接続方式(Connection type)PDP type IP and PDP type PPP are available for Internet connection type. You can select the Internet connection type you want to use or check the currently configured internet connection type.Caution•Be careful not to lose FOMA card. DOCOMO is not responsible for the lost or stolen device.•Do not transfer FOMA card to others.•Treat it carefully as the data stored in FOMA card can be easily damaged from scratching or bending.•When connecting FOMA terminal to a PC for the first time, you are required to enter PIN1 code to use FOMA card.•If an incorrect PIN1 code is entered 3 times in a row, the service will be suspended. To use it again, you must enter unblocking PIN1 code.•If an incorrect unblocking PIN1 code is entered 10 times in a row, FOMA card locks automatically, so be sure to keep a separate note of the number. Contact a DOCOMO shop if you are not able to unblock the locked PIN 1.ab接続方式 (Connection type)cd接続方式登録e接続方式設定リセット登録番号 (Registration number (cid))接続先 (Access Point Name (APN)) (Connection type setting reset) (Connection type registration)
73L-05A Connection Softwarec接続先(Access Point Name (APN))Configure APN for packet communication. You can configure APN of provider you want to use or check the currently configured APN.d（Connection type registration）Save the modified information to FOMA terminal.e（Connection type setting reset）Reset all PDP configurations.Saving and Editing the Provider Information•Save or edit the provider information you want to use.aSelect cidSelect the registration number to save/edit■cidThe registration numbers are available from cid1 to cid 10 in FOMA terminal.•To connect to a provider other than「mopera U」or「mopera」, you can set the access point name (APN) to any of cid2 or cid4 to cid10.bSelect the Internet connection type supporting Access Point.cEnter APN•When "cid=3"selected "PDP type IP" Configure mopera.net This service provides a maximum data speed of 7.2Mbps for receiving and 5.7Mbps for sending.•When "cid=1" selected "PDP type PPP" onfigure mopera.ne.jp This service provides a maximum data speed of 384kbps for receiving and 384kbps for sending.Registration number（cid） Access Point name（APN）1 mopera.ne.jp「mopera」2 Unassigned3 mopera.net「mopera U」4∼10 Unassigned
74 L-05A Connection SoftwaredClick Click Retrieving Provider InformationaIf select the cid of the "登録番号(Registration Number(cid))" b"接続方式(connection type)" and c"接続先(Access Point Name (APN))"will be displayed.Resetting FOMA Terminal•Allows you to reset FOMA terminal.aClick from the application option■ FOMA端末リセット(FOMA terminal reset)Reset FOMA terminal for the following cases•When FOMA terminal is operating improperly.•When FOMA card is reinserted while inserting the FOMA terminal to a PC.Note■ Configuring sender ID You can configure to display sender ID or not by adding 186/184 before APN.•Add "186." before APN if you want to display sender ID. •Add "184." before APN if you don't want to display sender.Registration APNDisplay sender ID 186.mopera.netNot display Sender ID 184.mopera.net FOMA 端末リセット(FOMA terminal reset)
75L-05A Connection SoftwarebClick •FOMA terminal is restarting.
77DOCOMO Connection ManagerDOCOMO Connection Manager ････････････････ 78Windows Version ･･････････････････････････････ 79Macintosh Version ･････････････････････････････ 83
78 DOCOMO Connection ManagerDOCOMO Connection ManagerDOCOMO connection manager is a software packets the necessary connection software to operate "定額データプラン接続ソフト (Flat-rate data plan connection software)" and measured data communication which are necessary when using flat-rate data plan.「DOCOMO connection manager」is a software to connect data communication terminal by data communication correponding terminal. Subscribing 「mopera U」or configuring a PC operates easily.Also, confirming amount of data communication and charges through charge counter feature is available. This manual introduces the installation method of DOCOMO connection manager.For connecting the terminal with Internet, agreement with the Internet service provider (「mopera U」 etc.) supporting service and data communication is required.View DOCOMO web site for detailed information (Japanese only). Connect/disconnectCharge counterWindows version Macintosh versionNote■ Using a flat-rate data plan•For using a flat-rate data plan, the agreement with the charge plan corresponding to the flat-rate data communication and internet service provider is required. View DOCOMO web site for further information.■ Using measured-rate data communication•Note that the communication fees may come high if you perform heavy packet communications such as viewing home page with pictures inside, downloading data (Ex.： Application/Music/Data/OS/anti-virus software update) etc. Note that when performing data communication after connecting this FOMA terminal with a PC by a USB cable, 「パケ･ホーダイ (Pake-hodai) 」、「パケ･ホーダイフル (Pake-hodaifull)」、「Biz･ホーダイ (Biz-hodai)」 and「Biz･ホーダイ ダブル (Biz-hodai double)」 are not included in the FOMA packet Flat-rate service.■ Using mopera•For connection configuration, view mopera web site.http://www.mopera.net/mopera/support/index.html (Japanese only)
79DOCOMO Connection ManagerWindows VersionBefore Installing DOCOMO Connection Manager■ Setting Internet ExplorerBefore installing this software, set connection setting to "ダイヤルしない (Do not dial)" in Internet Option of Internet Explorer.aStart Internet ExplorerSelect "ツール (Tool)"−"インターネットオプション (Internet Option)"bSelect "接続 (Connection)" tabSelect "ダイヤルしない (Do not dial)"cClick "OK"Note■ Use other connection software besides DOCOMO connection managerThis software has equate features with the following software. Therefore, it is not necessary to use the following software at the same time.※ If required, change the setting to not start or uninstall.- mopera U start up tools- mopera U connection & setting tool- FOMA PC configuration software- FOMA byte counterAlso, when using Mzone (Public Wireless LAN Connection) in this software, uninstall the following public wireless LAN connection software.※ When the following software are installed at the same time, the Mzone connection of this software is not available.- U Public Wireless LAN Utility Software- DOCOMO Public Wireless LAN Utility Software- DOCOMO Public Wireless LAN Utility Program
80 DOCOMO Connection ManageraLog on by DOCOMO connection manager user■For Windows VistaAn administrator is required. When logged on by other people than the administrator, entering user name and password will be asked.■For Windows XP/2000The user belongs to administrators group or the user of "コンピュータの管理者 (Administrator of computer)" operates log-on.bExiting all the applications launchedBesides anti-virus software, programs resident in Windows are also finished.•Ex: Right click the icon shown on task bar, and select "閉じる (Close)" or "終了 (Finish)".Installing DOCOMO Connection ManageraLaunch the installer of DOCOMO connection manager using the included CD-ROMSelect "付属CD-ROM (the included CD-ROM)"  "Windows"  "dcm_connect_manager""dcm_connect_full_setup.exe"bClick "続行 (Continue)" For Windows XP/2000, "ユーザーアカウント制御 (User account control)" screen is not displayed. Setup program starts right away.Note•When Windows XP does not contain MSXML6 and Wireless LAN API, installation is required before installing DOCOMO connection manager. Press "Install" when the confirmation screen is displayed.•After finishing installing MSXML6 and Wireless LAN API, if reboot Windows, the installation of DOCOMO connection manager starts automatically.
81DOCOMO Connection ManagercClick "次へ (Next)"dMake sure to confirm the caution and then click "次へ (Next)"eConfirm the content of the license agreement. When agree with the content, select "使用許諾契約の全条項に同意します (I agree with the license agreement stipulations)" and click "次へ (Next)"fConfirm the destination folder and click "次へ (Next)"
82 DOCOMO Connection ManagergClick "インストール (Install)"Installing starts.hClick "完了 (Finish)"Installing finishes.Launching DOCOMO Connection Managera"スタート (Start)""すべてのプログラム(All programs)""NTT DOCOMO""ドコモ コネクションマネージャ (DOCOMO connection manager)""ドコモ コネクションマネージャ (DOCOMO connection manager)"DOCOMO connection manager starts.bFor the first launching, the wizard setting is displayed automatically.The connection with Internet gets prepared when operating or setting following the instruction of software.Refer to 『ドコモ コネクションマネージャ操作マニュアル (DOCOMO connection manager operation manual).pdf』 for detailed information.
83DOCOMO Connection ManagerMacintosh VersionInstalling DOCOMO Connection ManageraLaunch the installer of DOCOMO connection manager from the included CD-ROM•Select "付属CD-ROM (included CD-ROM)"  "Mac"  "dcm_connect_manager"  "dcm_for_Mac"  "インストール(Install)"  Select "ドコモ コネクションマネージャをインストールします (Install DOCOMO connection manager)" and click "OK"Note•Just exiting the Internet browser or mail software does not disconnect the connection.When do not use communication, make sure to press "切断する (Disconnect)" button to disconnect the connection.For OS update, if auto update is set, the software will be updated automatically. Note that the packet communication fee may come high.DisconnectNote•Use Ver. 1.00.0003 or later for "DOCOMO connection manager for Mac".
84 DOCOMO Connection ManagerbClick "続ける (Continue)"cMake sure to confirm "大切な情報 (Important information)", and click "続ける (Continue)"dClick "続ける (Continue)"
85DOCOMO Connection ManagereConfirm "使用許諾契約 (The license agreement)", when agree with the content, click "同意する (I Agree)"Click "続行(Continue)"fConfirming the destination folder to install and click "インストール (Install)"gEnter administrator name and passwordClick "OK"The user account created after Mac OS X is set becomes the administrator of PC. Enter the used name and password.
86 DOCOMO Connection ManagerhClick "インストールを続ける (Continue installing)"iClick "ログアウト (Log out)"Installing finishes.Note•If click "ログアウト (Log out)", setting assistant screen is displayed.The connection with Internet gets prepared when operating or setting following the instruction of software.Refer to 『ドコモ コネクションマネージャ操作マニュアル (DOCOMO connection manager operation manual)』 for detailed information.
87DOCOMO Connection ManagerLaunching DOCOMO Connection Managera"アプリケーション (Application)" "ドコモ コネクションマネージャ (DOCOMO connection manager)" "ドコモ コネクションマネージャ (DOCOMO connection manager)"•DOCOMO connection manager starts.bFor the first launching, the wizard setting is displayed automaticallyThe connection with Internet gets prepared when operating or setting following the instruction of software.Refer to 『ドコモ コネクションマネージャ操作マニュアル (DOCOMO connection manager operation manual.pdf)』 for detailed information.Note•Just exiting the Internet browser or mail software does not disconnect the connection.When do not use communication, make sure to press "切断する (Disconnect)" button to disconnect the connection.For OS update, if auto update is set, the software will be updated automatically. Note that the packet communication fee may come high.Disconnect
89Configuring Network ManuallyConfiguring a Dial-up Network Manually ･････････ 90Communicating (Connecting by Dial-up) ･････････ 109
90 Configuring Network ManuallyConfiguring a Dial-up Network ManuallyThis section describes the steps to configure settings for packet communication without using L-05A connection software or DOCOMO connection manager.Setting APNSet the access point (APN) in packet communication. Up to 10 APN can be set up and they are managed with cid's. Communication software is required to enter AT commands. This section describes the steps necessary for using the "ハイパーターミナル(Hyper Terminal)" that comes with Windows.•The registration number (cid) 1 is set to mopera.ne.jp and the registration number 3 is set to mopera.net by default. Use cid 2 or from 4 to 10 when setting another access point.•"ハイパーターミナル(Hyper Terminal)" does not come with Windows Vista. To configure the settings in Windows Vista, use communication software compatible with Windows Vista. For the setting procedures, refer to the instruction manual and other documentation that came with the software to be used.• For a connection (APN) other than 「mopera U」 or 「mopera」, contact your ISP or network administrator.For Windows XPaConnect the FOMA terminal with a PC•Connecting method→P24bClick "スタート(Start)" "すべてのプログラ ム(All programs)"  "アクセサリ (Accessories)" "通信(Communication)"  "ハイパーターミナル(Hyper Terminal)"Hyper Terminal starts.■For Windows 2000Click "スタート(Start)"  "プログラム (Programs)"  "アクセサリ(Accessories)"  "通信(Communication)"  "ハイパーターミナ ル(Hyper Terminal)".cEnter a connection name in the "名前 (Name)" field  Click "OK"
91Configuring Network ManuallydEnter a non-existing phone number (such as "0") in the "電話番号(Phone Number)" field  Check that "FOMA L05A" is displayed for "接続方法(Connection Method)"  Click "OK"•If more than one modem name are displayed in the "接続方法(Connection Method)" field, check the FOMA terminal modem name and select the proper one.→P40oeClick "キャンセル(Cancel)" on the connection screenThe Hyper Termina screen opens.fEnter the APN in the following formatPressEnter AT+CGDCONT=<cid>,"<PDP type>","<APN>"Enter the following information in the corresponding <cid>, <PDP type> and <APN> sections.If "OK" appears after you enter the information, the APN has been setup.•If the entered characters do not appear, enter ATE1.If register an access point with PPP in the PDP type and XXX.com in the APN of cid2■To reset the specified APN settingsEnter AT+CGDCONT=<cid>■To view the registered APNEnter AT+CGDCONTcid ： Enter any number from 2, and from 4 to 10.※ Keep in mind that the old setting information will be overwritten if you select a cid number which has already been set.PDP type ： Select either PPP or IP for the connection method supported by the access point, and then enter the information enclosed in quotation marks ("").APN ： Enter the connection (APN) enclose it in quotation marks " ".
92 Configuring Network ManuallygCheck if "OK" is displayedhClick "ファイル(File)"  "ハイパーターミナル の終了(Exit Hyper Terminal)"iClick "はい(Yes)" on the confirming disconnection screen  Click "いいえ(No)" on the confirming to save screenHyper Terminal will quit, and the setting of the APN completes.Configuring Dial-up NetworkSet up the dial-up network on the PC.•For setting up a connection to other than 「mopera U」 or 「mopera」, contact your ISP or network administrator.Example: Connecting to the DOCOMO Internet connection service 「mopera U」, which is registered to <cid>=3For Windows VistaaClick "スタート(Start)"  "接続先 (Connection)"bClick "接続またはネットワークをセットアップします(Set up connection or network)"Note•The APN information is saved in the FOMA terminal. If you connect a different FOMA terminal, save the APN information again.•If you want to use the APN information registered on the PC, register the same APN in the same cid of the FOMA terminal.
93Configuring Network ManuallycSelect "ダイヤルアップ接続をセットアップします(Set up dial-up connection)"  Click "次へ(Next)"dWhen the modem selection screen appears, click "FOMA L05A"The modem selection screen opens only when the PC has more than one modem.
94 Configuring Network ManuallyeConfigure various settings, then click "接続(Connect)"• Enter the APN number in the "ダイヤルアップの電話番号(Phone number to a dial-up connection)".•Enter the user name and password specified by your ISP or network administrator in the "ユーザー名(User name)" and "パスワード(Password)" fields.•You can leave the user name and password fields unfilled when connecting to 「mopera U」/「mopera」.•Enter a connection name in the "接続名 (Connection Name)" field.fClick "スキップ(Skip)" on the "(接続名)に接続中... (Connecting to (APN))" screen The connection test will not be performed. Only the settings will be checked.•If you do not click "スキップ(Skip)", the connection to the Internet will be established.
95Configuring Network ManuallygClick "接続をセットアップします(Set up the connection)"  "閉じる(Close)"hClick "スタート(Start)"  "接続先 (Connection)"iSelect the created dial-up connection icon  Right click "プロパティ (Properties)"jCheck the settings on the "全般(General)" tab windowIf two or more modems are connected to a PC, enable only "モデム - FOMA L05A (Modem - FOMA L05A)" in the "接続方法 (Connection Method)" field.•Disable "ダイヤル情報を使う(Use dialing information)".
96 Configuring Network ManuallykClick "ネットワーク(Networking)" tab  Configure each settingPlace a checkmark next to the "インターネッ トプロトコルバージョン4 (TCP/IPv4) (Internet Protocol 4 (TCP/IPv4))" checkbox in the "この接続は次の項目を使用します(This connection uses the following items)" field. Obtain the settings for "QoSパケットスケジューラ(QoS Packet Scheduler)" from your ISP or network administrator.•To set up TCP/IP, click "プロパティ (Properties)". Contact your ISP or network administrator for setting up.lClick the "オプション(Option)" tab  Click "PPP設定(PPP Settings)"mRemove checkmarks from all items  Click "OK"nOn the "オプション(Option)" tab window, click "OK"
97Configuring Network ManuallyFor Windows XPaClick "スタート(Start)"  "すべてのプログラム(All programs)"  "アクセサリ (Accessories)"  "通信(Communication)"  "新しい接続ウィザード(New Connection Wizard)"bOn the New connection wizard screen, click "次へ(Next)"cSelect "インターネットに接続する(Connect to the Internet)"  Click "次へ(Next)"dSelect "接続を手動でセットアップする(Set up the connection manually)"  Click "次へ(Next)"
98 Configuring Network ManuallyeSelect "ダイヤルアップモデムを使用して接続する(Use a dial-up modem to connect)"  Click "次へ(Next)"fIf "デバイスの選択(Select a device)" screen appears, check in "モデム - FOMA L05A (COM4) (Modem - FOMA L05A(COM4))" checkbox  Click "次へ(Next)"The "デバイスの選択(Select a device)" screen appears only when the PC has more than one modem.gEnter a name in the "ISP名(ISP Name)"field  Click "次へ(Next)"hEnter the APN phone number in the "電話番号(Phone Number)" field  Click " 次へ (Next)"■For packet communicationEnter "*99***<cid>#". Enter the registered number of APN in <cid>. (P73)
99Configuring Network ManuallyiSelect the connection usage range  Click "次へ(Next)"Select a user.• Depending on the PC settings, this screen may not appear.jFill in the "ユーザー名(User Name)", "パスワード(Password)", and "パスワードの確認入力(Confirm password)" fields  Click "次へ(Next)"Enter the information provided by your ISP or network administrator.•Enter "ユーザ名(User name)" and "パスワード (Password)" correctly according to the instruction from the provider. Pay attention to the capital characters.•To connect to 「mopera U」 or 「mopera」, these fields can be left unfilled.kClick "完了(Finish)"The new connection wizard appears.lClick "スタート(Start)"  "すべてのプログラム(All programs)"  "アクセサリ(Accessories)"  "通信(Communication)"  "ネットワーク接続(Network Connection)"
100 Configuring Network ManuallymSelect the created dial-up connection icon Right click Click "プロパティ(Properties)" nCheck the settings on the "全般(General)" tab window•If more than one modem is connected to a PC, enable only "モデム - FOMA L05A (COM4) (Modem - FOMA L05A (COM4))" in the "接続方法 (Connection Method)" field.•Disable "ダイヤル情報を使う(Use dialing information)".
101Configuring Network ManuallyoClick the "ネットワーク(Networking)" tabConfirm each itemClick "設定(Settings)"•Select "PPP:Windows 95/98/NT4/2000, Internet" in the "呼び出すダイヤルアップ サーバ ーの種類(Dial-up server type to call)" field•Enable "インターネットプロトコル(Internet Protocol) (TCP/IP)" in the "この接続は次の項目を使用します(This connection uses the following items)" field. You cannot change the settings of "Qosパケットスケジューラ (QoS Packet Scheduler)". Use it as usual.•When connecting to provider, to confirm the TCP/IP setting contact the provider or network administrator.pClick "設定(Settings)"qRemove checkmarks from all items  Click "OK"rclick "OK" on the "ネットワーク(Networking)" tab windowFor Windows 2000aClick "スタート(Start)"  "プログラム(Programs)"  "アクセサリ(Accessories)"  "通信(Communication)"  "ネットワークとダイヤルアップ接続(Network and Dialup Connections)"bOn the Network and Dial-up connection screen, double-click the"新しい接続の作成 (Create new connection)" icon
102 Configuring Network ManuallycIf the location information screen appears, enter "市外局番(City code)"  Click "OK"This appears only when "新しい接続の作成 (Create new connection)" is launched for the first time. Go to Step 5 when launching this for the second time or later.dOn the phone and modem option screen, click "OK"eOn the Network connection wizard screen, click "次へ(Next)"fSelect "インターネットにダイヤルアップ接続する(Connect to Internet via dial-up)"  Click "次へ(Next)"
103Configuring Network ManuallygSelect "インターネット接続を手動で設定するか、またはローカルエリアネットワーク(LAN)を使って接続します(Set up the Internet connection manually, or connect to the Internet using LAN)"  Click "次へ(Next)"hSelect "電話回線とモデムを使ってインターネットに接続します(Connect to the Internet using a telephone line and a modem)"  Click "次へ(Next)"
104 Configuring Network ManuallyiIf the modem selection screen opens, select "FOMA L05A"  Click "次へ (Next)"The modem selection screen opens only when the PC has more than one modem.•If "FOMA L05A" is not displayed, click "インターネットへの接続に使うモデムを選択する (Select the modem used to connect to the Internet)" field and then select "FOMA L05A".jEnter the APN phone number in the "電話番号(Phone Number)" field  Click "詳細設定(Advanced settings)"•Do not enter anything in "市外局番(City code)" field•Disable "市外局番とダイヤル情報を使う(Use the city code and dialing information)".■Packet communication informationEnter "*99***<cid>#". Enter registration number of APN in <cid>.
105Configuring Network ManuallykConfigure the settings on the "接続(Connection)" tab window according to the examples on the screen.•If you are connecting to other than「mopera U」 or 「mopera」, fill in the "接続の種類 (Connection type)" and " ログオンの手続き (Log on procedures)" fields according to the information provided by your ISP or network administrator.lClick the "アドレス(Address)" tabSet each itemClick "OK"•If you are connecting to other than 「mopera U」 or 「mopera」, fill in the "IPアドレス (IP address)" and "ISPによるDNS (ドメインネームサービス) アドレスの自動割り当て(Assign DNS address automatically by ISP)" fields according to the information provided by your ISP, and follow the instruction from provider.mOn the "インターネットアカウントの接続情報 (Internet account connection information)" screen, click "次へ(Next)"
106 Configuring Network ManuallynEnter "ユーザー名(User Name)" and "パスワード(Password)"  Click "次へ(Next)"•Enter "ユーザ名(User name)」 and "パスワード(Password)" correctly according to the instruction from the provider. Pay attention to the capital characters.Note•For 「mopera U」 or 「mopera」, connection is operated even when "ユーザ名(User name)" field and "パスワード(Password)" field are empty. The screen "ユーザ名を空白のままにしておきますか？ (Is it OK to enter nothing in User name?)" is displayed in this case. Click "はい(OK)" in each screen.
107Configuring Network ManuallyoEnter a connection name in the "接続名(Connection Name)" field  Click "次へ (Next)"pSelect "いいえ(No)"  Click "次へ(Next)"•When setting Internet mail, select "はい(OK)". Contact the provider for detailed information of setting.qClick "完了(Finish)"•If "今すぐインターネットに接続するにはここを選び完了をクリックしてください(Select this to connect to the Internet now and click Finish)" appears, disable the option.rSelect the created dial-up connection icon  Click "ファイル(File)"  "プロパティ(Properties)"
108 Configuring Network ManuallysCheck the settings on the "全般(General)" tab window•If more than one modem is connected to a PC, enable only "モデム - FOMA L05A (COM3) (Modem - FOMA L05A (COM3))" in the "接続の方法 (Connection Method)" field•Disable "ダイヤル情報を使う(Use dialing information)".tClick the "ネットワーク(Networking)" tabConfirm each itemClick "設定(Settings)"•Select "PPP:Windows 95/98/NT4/2000, Internet" in the "呼び出すダイヤルアップサーバーの種類(Dial-up server type to call)" field.•Enable only "インターネットプロトコル (Internet protocol) (TCP/IP)" in the "コンポーネント(Components)" field.uClick "設定(Settings)"vRemove checkmarks from all items  Click "OK"wClick "OK" on the "ネットワーク(Networking)" tab window
109Configuring Network ManuallyCommunicating (Connecting by Dial-up)イヤルアップ接続するThis section describes steps to start and terminate communication without using L-05A connection software or DOCOMO connection manager.•Check whether the FOMA terminal and the PC are connected properly before starting communication.→P24•When performing communication, connect the FOMA terminal you used to configure the settings. If a different FOMA terminal is connected, L-05A Communication Configuration Files (Drivers) may need to be reinstalled.For Windows VistaaClick "スタート(Start)"  "接続先 (Connect to)"  Select the access point that has been set up  Click "接続 (Connect)." ■For Windows XPClick " スタート(Start)"  "すべてのプログラム(All programs)" "アクセサリ (Accessories)"  "通信(Communication)"  "ネットワーク接続(Network connection)"  Double click the APN that has been set up■For Windows 2000Click "スタート(Start)"  "プログラム (Programs)"  "アクセサリ(Accessories)"  "通信(Communication)"  "ネットワークとダイヤルアップ接続(Network and Dialup Connections)"  Double-click the APN icon that has been set up.bEnter "ユーザー名(User Name)" and "パスワード(Password)"  Click "ダイヤル(Dial)"The APN will be connected.•To connect to 「mopera U」 or 「mopera」 , you can leave the " ユーザー名(User Name)" and "パスワード(Password)" fields unfilled and click "ダイヤル(Dial)". If another ISP or dialup connection is selected, fill in the "ユーザー名(User Name)" and "パスワード (Password)" fields and click "ダイヤル (Dial)".•You can save the user name and password or just the password to skip entering them next time.•Depending on the operating system, a connection completion screen may appear when the dial-up connection is established. However, the connection completion screen does not appear if you previously set the completion message not to appear.
110 Configuring Network ManuallyDisconnecting CommunicationExiting the Internet browser may not terminate the connection. Perform the following steps to terminate the connection securely.For Windows VistaaClick the dial-up icon in the task tray of the PCA screen indicating the connection status appears.bClick "接続または切断(Connect or disconnect)"■For Window XP/2000The above screen will not be displayed. Follow the next procedure.cClick "切断(Disconnect)"The communication will be terminated. Note•The communication speed shown on the PC screen may be different from the actual communication speed.
111Overseas UseInternational Roaming Service (WORLD WING) ･･ 112Services Available Overseas ････････････････････ 112Before Using Overseas ･･････････････････････････ 113Setting the Searching Method for Available Networks ･･････････････････････････････････････ 115Configuring Network･･･････････････････････････ 116
112 Overseas UseInternational Roaming Service (WORLD WING)WORLD WING is DOCOMO's international roaming service that provides telephone and other types of communication services overseas out of the service area of FOMA network, using affiliated overseas network.•The following 3 types of communication are included in overseas network.■3G networkA third generation mobile communication network complying with 3GPP Global standards. (3rd Generation Partnership Project)※※ The local satandardization organization established for the development of common technical specifications related to 3rd Generation Mobile Communication Systems (IMT-2000)■GSM (Global System for Mobile Communication) networkThe second generation mobile communication network in a digital communication system that is most widely used around the world.■GPRS (3General Packet Radio Service) networkGPRS is the 2.5 generation mobile communication system that enables high speed packet communication using GSM.•It is available to use 3G network or GSM/GPRS network service within service area. For countries/areas support 3G850MHz/GSM850MHz, it is also available to use.•Before using the FOMA terminal overseas, refer to the followings.- "Mobile Phone User's Guide [International Services]"- DOCOMO "International Service Web site"Services Available OverseasAvailable communication services may vary depending on the overseas carrier or network.Available Communication Services※ Sending and receiving SMS may be available in overseas.Please understand that communication fee is countedwhen sending SMS.※ Packet communication is not available for GSM networkcommunication type.Service DescriptionData Communication Available for data communication using packets communication.Note•For details on available communication services while using international roaming, refer to Mobile Phone User's Guide [International Services] or visit DOCOMO "International Service Web site".•Voice call or video telephony features are not supported by L-05A.
113Overseas UseBefore Using OverseasSTEP1：Before Leaving JapanSTEP2：While OverseasSTEP3：After Coming Back to JapanBefore Leaving JapanBefore using the FOMA terminal overseas, refer to the followings.•"Mobile Phone User's Guide [International Services]"•"Mobile Phone User's Guide [Network Services]"•DOCOMO "International Service Web site"■ Subscription•If you subscribed to the FOMA service after September 1, 2005, no separate subscription is required to use ″WORLD WING″. If you subscribed to the FOMA service on or before August 31, 2005 and have not subscribed to ″WORLD WING″, a separate subscription is required to use it.•A FOMA card (green/White) made available for WORLD WING must be inserted in the FOMA terminal.■ Power source and voltage in the country or region of stay•Countries and regions may have different power sources, voltages or power outlet shapes. Check these in the instruction manual for your PC or web sites of the PC manufacturer in advance.■ Network setup•You can change network setup from overseas.→P116■ Internet access•For overseas access points or settings for using the Internet overseas, contact your Internet service provider.•If you subscribe to mopera U, visit the mopera U web site.http://www.mopera.net/ (Japanese only)While Overseas■ Switching networksSearching for and connecting to an access point are performed automatically by default. No special settings are required.■ Main screen display areaThe name of the connected carrier can be viewed in the display area of the Main screen.→P116Inquries overseasIf your FOMA card (green/white) is lost or stolen overseas, contact DOCOMO immediately and temporarily suspend your subscription. For inquiry information, see "docomo Information Center" on the back of this manual. Call or data communication charge will still on you after the terminal was lost or stolen.Note•You can manually switch networks if you want to connect to a particular network. See procedure 3 of "ネットワークを設定する (Configuring Networks)" (P116)差替え予定
114 Overseas Use■ Country Codes for Major Countries※ For country code or detailed information, refer to "MobilePhone User's Guide [International Services]" or DOCOMO"International Service Web site".■ International Access Codes for Major Countries (Table 1)※ For codes of other countries or details, visit DOCOMO "International Service Web site".Area Code Area CodeU.S.A 1 Germany 49 U.K. 44 Turkey 90 Italy 39 Japan 81 India 91 New Caledonia 687 Indonesia 62 New Zealand 64 Egypt 20 Norway 47 Australia 61 Hungary 36 Austria 43 Fiji 679 Netherlands 31 Philippines 63 Canada 1 Finland 358 Korea 82 France 33 Greece 30 Brazil 55 Singapore 65 Vietnam 84 Switzerland 41 Peru 51 Sweden 46 Belgium 32 Spain 34 Hong Kong 852 Thailand 66 Macau 853 Taiwan 886 Malaysia 60 Tahiti 689 Maldives 960 Czech 420 Russia 7 China 86Area Code Area CodeIreland 00 Germany 00 U.S.A. 011 Turkey 00 U.A.E. 00 New Zealand 00 U.K. 00 Norway 00 Italy 00 Hungary 00 India 00 Philippines 00 Indonesia 001 Finland 00 Australia 0011 France 00 Netherlands 00 Brazil 0021 Canada 011 0014 Korea 001 Vietnam 00 Greece 00 Belgium 00 Singapore 001 Poland 00 Switzerland 00 Portugal 00 Sweden 00 Hong Kong 001 Spain 00 Macau 00 Thailand 001 Malaysia 00 Taiwan 002 Monaco 00 Czech 00 Luxembourg 00 China 00 Russia 810 Denmark 00
115Overseas Use■ International Phone Codes for Universal Number(Table 2)※ For codes of other countries or details, visit DOCOMO "International Service Web site".After Coming Back to JapanAfter coming back to Japan, the FOMA network will be connected automatically.■ If connection can not be establishedSet to "自動検索(Auto)" from "ネットワーク検索(Search Network )" of "ネットワークを設定する(Configuring network)" (P116)Setting the Searching Method for Available NetworksSwitching Carriers ManuallyThe FOMA terminal is set to automatically find and switch to an available network in the country of stay by default. However, if you have a preferred network in the area or network cannot be found automatically, you can set to a network manually. For details, see "Configuring Networks" (P116).Area Code Area CodeIreland 00 Taiwan 00 U.S.A. 011 China 00 Argentina 00 Denmark 00 U.K. 00 Germany 00 Israel 014 New Zealand 00 Italy 00 Norway 00 Australia 0011 Hungary 00 Austria 00 Philippines 00 Netherlands 00 Finland 990 Canada 011 France 00 Korea 001 Brazil 0021 Colombia 009 Belgium 00 Singapore 001 Portugal 00 Switzerland 00 Hong Kong 001 Sweden 00 Malaysia 00 Spain 00 South Africa 09Thailand 001 Luxembourg 00
116 Overseas UseConfiguring Network•Allow you to configure network by L-05A connection software.aClick from the application option screenbSpecify a "優先ネットワーク(Prior network)" (Network priority order selection setting)cSearching network■自動検索(Auto)Network can be searched automatically.■手動検索(Manual)Connect to the listed networks manually.※ If network search mode is set to "manual" overseas,reset to "Auto" after coming back to Japan.dSpecify if display or hide the network information■表示する(Display)The name of the network receiving current service is displayed on the screen.■表示しない(Hide)The name of the network receiving current service is not displayed on the screen.eClick the applicable •The information entered will not be set without clicking the applicable fClick 適用 (Application)優先ネットワーク (Prior network) ネットワーク検索(Network Search)適用 (Application)適用 (Application)ネットワーク情報(Network Information)
117Overseas UseNote•How to manually configure network- Select "手動選択(Manual)"- The available network list will be displayed after searching.- Select one from the available networks.- Click •Network is not displayed in FOMA area when even if "display" is set in network information.•Connecting to Internet or sending SMS may not be able to operate properly when network setting is changed manually.•While using Oversea→P111- When you are in roaming area and set FOMA terminal to automatically find and you can have automatic roaming service. If network can not be found automatically, select the available network service manually.- Some communication services may not available depending on the overseas carrier or network.
119Appendix/TroubleshootingAT Commands ･･･････････････････････････････････ 120AT Command List････････････････････････････････ 121Troubleshooting ･････････････････････････････････ 130Error Messages･･････････････････････････････････ 132Warranty and After-Sales Service ･･･････････････ 134Updating software ･･･････････････････････････････ 135Main specifications ･･････････････････････････････ 136Export Controls of the Product and Accessories ･･･ 137Intellectual Property Rights ･････････････････････ 139Index ･････････････････････････････････････････････ 141
120 Appendix/TroubleshootingAT CommandsAT commands are used to check the FOMA terminal function settings or status by using a PC. Usually, the communication software issues AT commands so you do not need to be concerned about them. Use AT commands if you want to control the FOMA terminal in your own way.Form of AT CommandsAT commands should be entered on the Terminal Mode screen of the communication software. Use only single-byte alphanumeric characters.<Example>•An AT command must be entered on a single line including parameters (numbers and symbols) following the command. On the Terminal Mode screen of the communication software,"one line" is from the first character to the character before .Note•In the Terminal mode, a PC functions as a communication terminal. Characters entered from the keyboard are sent to a line connected to a communication port.ATD ＊ 99 ＊＊＊ 3#Hard Return Parameter: ContentCommand Name
121Appendix/TroubleshootingAT Command ListThe following AT commands can be used on the ″L-05A″modem port.•[&F]：A command to initialize settings used as AT&F command.•[?][=?]：The current settings appear when adding″?″at the end of the command, and the effective range of the current settings appears when adding″=?″at the end of the command. Command Overview Parameters/Description Comments ExamplesAT&C<n> Select the operating conditions of the circuit CD for DTEn=0: Always keeps CD singal ONn=1 (default): CD changes depending on the other party's modem status.AT&C1 OK AT&F<n> Reset the FOMA terminal AT command set values to factory defaults If executed during a communication, the line is disconnected.Only n=0 can be set (Skippable) -AT+CGDCONT [?] [=?] Set APN when sending Packet communication.Refer to P128 Refer to P128AT+CGEQMIN [?] [=?] Register criteria value for determining if QoS (Quality of Service) sent from network when PPP Packet communication is established, is acceptable or not.Refer to P128 Refer to P128AT+CGEQREQ [?] [=?] Set QoS(Quality of Service) to request for the network when PPP Packet communication is established.Refer to P128 Refer to P128AT+CGMR Display the version of the AT+CGMR FOMA terminal.- AT+CGMR 1234567890123456OK
122 Appendix/TroubleshootingAT+CGREG=<n> [&F][?] [=?] Set whether to be notified of the network registration status.＜n＞ n=0(default): Do not note.n=1: Notify when outside and inside the service area is changed.Execute「AT+CGREG?」then appears as ｢+CGREG:<n>,<state>」＜state＞ 0:Not registered1:Registered Home Network4: Unknown5: Registered (while roaming)AT+CGREG?+CGREG: 0,1OKAT+CGREG=?+CGREG: (0-2)OKAT+CGSN Display the serial number of the FOMA terminal.- AT+CGSN 12345678901 2345 OK AT+CMEE=<n> [&F][?] [=?] Set the error report form of the FOMA terminal.n=0: Display「ERROR」n=1: Display in the form of 「+CMEE ERROR: xxxx」(where xxxx are numbers)n=2(default): Display in the form of「+CMEE ERROR: xxxx」(where xxxx are text)※ If using ATZ or AT&F command to default, "0" is setup. Note that when connecting L-05A to power, the value of ATZ or AT&F command differs.AT+CMEE=0 OK AT+CMEE?+CMEE: 0OK AT+CMEE=?+CMEE: (0, 1, 2)OK Command Overview Parameters/Description Comments Examples
123Appendix/TroubleshootingAT+ CNUM Display the own number of the FOMA terminalExecuting「AT+CNUM」displays in the form of「+CNUM: <number>, <type>」number: phone numbertype=129: Excluding the international access code+type=145: Including the international access code+AT+CNUM +CNUM:,″09080189242″,129 OK AT+COPS=〔<mode>〔,<format>〔,<oper>〔,<stat>〕〕〕〕[?] [=?]Select and set carrier's name/Plmn Number.<mode>0：Auto (Searching network automatically and then change communication service)1：Manual（to connect <oper> communication service)2：Disconnection communication service※Not supported3：Mapping don't excute.4：Auto manual（In case, to disconnect <oper>communication service that excute automatically）※Not supported<format>2：Fixed number<oper> represents country code(MCC) plus network code(MNC).“ 44010”is displayed for MCC=440 and MNC=10AT+COPS?+COPS: 0,0,””,2OKAT+COPS=?+COPS:（2,””,””,”44010”,2）,（3,””,””,”44020”,2）,,（0,1,2,3,4）,（0,1,2） OKCommand Overview Parameters/Description Comments Examples
124 Appendix/TroubleshootingAT+CPAS [=?] Display FOMA terminal state Displays in the form of「+CPAS : <n>」.                 n=0: Available to set AT commands.n=3: Available and receivingn=4: Available and receivingAT+CPAS +CPAS:0 OK AT+CPAS=? +CPAS :（0,3,4）OK AT+CPIN=″PIN″/ AT+CPIN=″PUK″ ″PIN″ [?] Command to enter the PIN code or unblocking PIN code for FOMA card.Enter the PIN1 code for ″PIN″, and enter unblocking PIN code for ″PUK″.Executing「AT+CPIN?」displays「+CPIN: <n>」.n=READY: Authenticatedn=SIM PIN: Waiting for entryn=SIM PUK: Waiting forunblocking PIN1 code entryn=ERROR: Locked(+CPIN:SIM PIN status) AT+CPIN=″1234″ OK(+CPIN:SIM PUK status) AT+CPIN=″ 12345678″,″1234″OKAT+CUSD[&F]Inquire the change or setting contents of Internet configuration related to the extra service.Form : AT+CUSD=<n>,"<str>"[,0]n=0 : middle result Do not send <m>[<str>,<dcs>] (default)n=1 : middle result Send <m>[<str>,<dcs>] Middle result : m=0 : setting finishes m=1 : information requirement from network exists.str :0∼9、＃、＊のみ使用可能。   <str>は""で囲むAT+CUSD=0,"xxxxxxxxx"OKAT+CUSD=1,"＊148＊1＊0000#",0+CUSD:0,"148＊7#",0OKAT+CUSD=?+CUSD: 0OKAT+CUSD=?+CUSD:(0-2)OKCommand Overview Parameters/Description Comments Examples
125Appendix/TroubleshootingAT＊DANTE Display the signal strength (number of antenna bars) of the FOMA terminal.Result format: ＊DANTE:<m>m=0 ：Out of the service aream=1 : State of 0 or 1 antenna bar displayedm=2 : State of 2 antenna bars displayedm=3 : State of 3 antenna bars displayedAT＊DANTE＊DANTE:3OKAT+GCAP Display the capability list of the FOMA terminal.- AT+GCAP +GCAP: +CGSM,+DS,+ESOK AT+GMI Display the manufacturer of the FOMA terminal.-AT+GMI LG Electronics Inc.OK AT+GMM Display the name of the FOMA terminal. - AT+GMM FOMA L05A OK AT+GMR Display the s/w version of the FOMA terminal.-AT+GMR L05A-01-Vxxx-440-10OKCommand Overview Parameters/Description Comments Examples
126 Appendix/TroubleshootingAT+IFC=<n>,<m> [&F][?] [=?] Set the local flow control method between the PC and the FOMA terminal.n : DCE by DTE controln=0 : No flow control.n=1 : Perform XON/XOFF control.n=2 (default): Perform RS/CS (RTS/CTS) flow control.m : DTE by DCE control.m=0 : Perform No flow control.m=1: XON/XOFF control.m=2(default) : Perform RS/CS (RTS/CTS) flow controlAT+IFC=2, 2OK AT+IFC? +IFC: 2,2OK AT+WS46=<n> [&F][?] [=?] Set the wireless network to be used by the FOMA terminal when dialing.12: GSM22: 3G (WCDMA)25: GSM+3G (WCDMA)AT+WS46? 25 OK A/ Retry a command just before performing is not needed after entering command.A/OK ATD Sending packet Sending packet：ATD*99***＜cid＞# ＜cid＞1∼10： + Display the APN that configured +CGDCONT ATD*99***3# CONNECT 7200000 ATE<n> [&F] Set whether to echo back the text sent from a PC.n=0 : Not echo back.n=1（default) : Echo back.ATE1 OKATI<n> Display the recognition code n=0 : Display [NTT DOCOMO] n=1 : Display the name of the FOMA terminal（Same as +GMM）n=2 : Display the FOMA terminal version（same as +GMR）n=3 : Display OKn=4 : Display the details of communication functions of the FOMA terminal.ATIONTT DoCoMo OK Command Overview Parameters/Description Comments Examples
127Appendix/TroubleshootingATS3=<n> [&F] [?] Set the return character (CR) to recognize the end of AT command text string.n=13（default） : only n=13 can be specified.ATS3=13 OK ATS4=<n> [&F] [?] Set the line feed (LF) character. It is positioned next to the return character (CR) if displaying the result code in alphanumeric characters.Only n=10 (default) can be specified. ATS4=10 OK ATS5=<n> [&F] [?] Set the back space (BS) character to delete the last character in the input buffer while AT commands are entered.Only n=8 (default) can be specified. ATS5=8 OK ATV<n> [&F] Set the display method of the result code.n=0 :Display in numeric characters. n=1(default): Display in text.ATV1 OK ATZ Reset the settings on the FOMA terminal with the nonvolatile memory contents. If performed during a communication, the line is disconnected.-ATZ OK Command Overview Parameters/Description Comments Examples
128 Appendix/TroubleshootingSupplementary Explanation of AT Commands■ Command name：+CGDCONT•OverviewSet APN when sending packet connection.•Form+CGDCONT=[<cid>[,″<PDP type>″[,″<APN>″]]]•Parameter descriptionsSet the destination (APN) when sending packets. See the following examples for command operations.<cid>※1：1∼10<PDP type>※2：PPP or IP<APN>※3：Optional※1 <cid> is the number used to control the destination (APN) for the packet communication to be registered in FOMA terminal. 1 to 10 can be registered. The default value of <cid>=1 is 「mopera.ne.jp」 and <cid>=3 is 「mopera.net」. Set cid to 2 or a number between 4 and 10.※2 <PDP type> is a protocol for packet communication.※3 <APN> is optional string that indicates each destination.•Command examplesCommand to register an APN with the name of abc (When PDP type is PPP, cid is 3）AT+CGDCONT=2,″IP″,″abc″OK•Operations without a parameterAT+CGDCONT=：Clear all the settings of <cid>.However, the setting of <cid>=1 or <cid>=3 is reset to the value when purchasing.AT+CGDCONT?：Display the current settings.■ Command name: +CGEQMIN=[Parameter]•OverviewRegister the threshold to accept the QoS (Quality of Service) sent from the network when packet communication is established.•Format+CGEQMIN=<cid>[,,<Maximum bitrateUL>[,<Maximum bitrate DL>]]]•Parameter description<cid>※1：1∼10<Maximum bitrate UL>※2：None (default)<Maximum bitrate DL>※2：None (default)※1 <cid> is a number used to manage the access point (APN) for the packet communication registered in the FOMA terminal. ※2 <Maximum bitrate UL> and <Maximum bitrate DL>indicate the minimum communication speed [kbps] of upload and download traffic respectively between the FOMA terminal and the base station. If these are set to None (default), all speeds are permissible. Be aware that a packet communication may not be established because any other speed than this is not permissible.•Command examples(1) Command to permit all speeds for both upload and download (When cid=2)AT+CGEQMIN=2OK(2) Command to permit only 5,700kbps for upload and 7,232kbps for download (When cid=2)AT+CGEQMIN=2,,5700,7232OK(3) Command to permit 5,700kbps for upload and all speeds for download (When cid=2)AT+CGEQMIN=2,,5700OK
129Appendix/Troubleshooting(4) Command to permit all speeds for upload and only 7,232kbps for download (When cid=4)AT+CGEQMIN=4,,,7232OK•Operations without a parameterAT+CGEQMIN=：Reset all <cid> to their defaults.AT+CGEQMIN=<cid>：Reset the specified <cid> to its default.■ Command name: +CGEQREQ=[Parameter]•OverviewSet the QoS (Quality of Service) requested to the network when packet communication is dialed.•Format+CGEQREQ=[<cid>[,,<Maximum bitrate UL>[,<Maximum bitrate DL>]]]•Parameter description<cid>※1：1∼10<Maximum bitrate UL>※2：None (default)<Maximum bitrate DL>※2：None (default)※1 <cid> is a number used to manage the access point (APN) for the packet communication registered in the FOMA terminal. ※2 <Maximum bitrate UL> and <Maximum bitrate DL>indicate the minimum communication speed [kbps] of upload and download traffic respectively between the FOMA terminal and the base station. If these are set to None (default), all speeds are permissible. Be aware that a packet communication may not be established because any other speed than this is not permissible.•Command exampleCommand to require 5,700kbps for upload and 7,232kbps for download (When cid=2)AT+CGEQREQ=2,2,5700,7232OK•Operations without a parameterAT+CGEQREQ=：Reset all <cid> to their defaultsAT+CGEQREQ=<cid>：Set the specified <cid> as default.Result Codes■ List of result codesNote•This command, (+CGDCONT, +CGEQMIN, + CGEQREQ) is not reset by [&F] and [Z], either.Numeric display Text display Description0 OK Operation performed properly1 CONNECT Connected to other party3 NO CARRIER Line disconnected4 ERROR Unable to accept command
130 Appendix/TroubleshootingTroubleshootingFirst, check whether software is required to update. Update software if necessary. (Updating Software⇒P135)Contact General Inquiries specified by DOCOMO located in "Repairs" at the last page of the manual if the symptom is not improved after confirming the check box.■ The FOMA terminal is not recognizedSymptom CheckFOMA terminal is not recognized Reinsert the FOMA terminal all the way into the USB port securely.Verify the L-05A Communication Configuration Files (Drivers) for the FOMA terminal functioning properly.→P35, P42Communication may fail and the FOMA terminal cannot be properly recognized and functioned, if the PC is started up or restarted with the FOMA terminal FOMA terminal left inserted in it. In this case, remove and reinsert the FOMA terminal. If communication fails even after the FOMA terminal is inserted again, remove it once, restart the PC, then insert the FOMA terminal into the PC again.When connecting the FOMA terminal with a USB port, if data communication is not available without being recognzied, double click the "DOCOMO" icon recognized as a CD drive or start "L-05A connection software" or "DOCOMO connection manager" to recognize the FOMA terminal as a modem.The FOMA card will not be able to use if PIN1 unlock code is wrongly entered 10 times in a low. For further information, visit DOCOMO shop.
131Appendix/Troubleshooting■ Communication problems■ Problems with AT Commands■ Other problemsSymptom CheckCommunications are not possibleVerify that signals are received in the service area.In the setting of Send Caller ID does not conform to the provider's instructions, communication may not be performed.→P74, P90 Check if you set the FOMA Card Setting to ″PIN1 unblocking″.→P69If set to (PIN1 Lock), launch the L-05A connection software, then change FOMA card setting to ″PIN1 unblocking″.→P71 Check the property settings of the modem and the registration of the destination (APN)Symptom Check[ERROR] appears when a command is enteredVerify that you entered a correct ATcommand.Check the properties of the terminal software to see whether a device other than the FOMA terminal is selected[OK] does not appear after an AT command is entered. Check the L-05A Communication Configuration Files (Drivers) have been installed and functioned properly.Verify that the commands start with "AT" or "at".Symptom CheckThe terminal stopped working suddenly Verify that the FOMA CARD is properly inserted to FOMA terminal.→P19Your PC operating environments may have changed because a new peripheral or software was installed. Make a confirmation with manufacturer or maker of accessory or software.The FOMA terminal is not detected if it is inserted into a USB port while installing the L-05A Communication Configuration Files (Drivers).Please confirm the followings.•Whether the PC or OS you are using is in the latest condition?(If required, apply revision program of OS or a maker.)•Whether the FOMA terminal recognizes normally when other USB devices are inserted into the USB port?•Whether the FOMA terminal operates normally when being inserted into another PC?•Whether the FOMA terminal operates normally when being reset to its default?※：For inquiries related to OS or PC, contact Microsoft or PC manufactures.Internet connection speed decreased significantlyInserting FOMA terminal directly to a PC may result in deterioration of performance depending on the type of PC, specification and degree of electromagnetic interference.Deterioration of performance may occur to the service areas where W-CDMA/HSDPA/GSM network are unstable. In this case, move to other area and try to connect again.
132 Appendix/TroubleshootingError MessagesError Messages Description圏外 You are out of service area or available network.サービス地域ではありません。ネットワークを再検索しますか?You may be out of service area or available network, or network error. Please do network setting again.端末の認証に失敗しました。顧客センターまたは代理店にお問い合わせください。Communication may fail and the FOMA terminal cannot be properly recognized if the PC is started up or restarted with the FOMA terminal left inserted in it. In this case, remove and reinsert the FOMA terminal. If communication fails even after the FOMA terminal is inserted again, remove it once, restart the PC, then insert the FOMA terminal into the PC again. Contact DOCOMO shop if the same problems persist.データ通信中には設定できません。終了後に設定してください。You cannot customize setting during data communication. Try again after closing data communication.変更するPIN１コードと確認用のPIN１コードが異なります。Two of new PIN1 are not identical each other. New PIN1 you want to change is not matched to the PIN1 you entered for verification purpose. Enter correct PIN1.FOMAカードが挿入されているか確認してください。Make sure to insert FOMA card into FOMA terminal before inserting to a PC.FOMA端末が取り外されました。 Do not remove FOMA card while using FOMA terminal.FOMA端末が取り付けられていません。 Verify the FOMA terminal is properly inserted into a PC. Verify that the FOMA terminal is properly recognized by the PC.PIN1を複数回間違えたため使用できなくなりました。（PIN1 blocked）PIN1コードがロックされています。An incorrect PIN1wasimproperly entered 3 times in a row. Available functions will be limited. Enter PIN unblocking code to unlock.PIN1コードが違います。残り（○/3）回入力可能です。再入力してください。An incorrect PIN1 code has been entered. Enter the correct PIN1 code againPIN1コードが間違います。（PIN1コードは0123456789のみ使用できます。）You can use 0,1,2,3,4,5,6,7,8,9 as a valid PIN1 code. Others are invalid.PIN1コードは4∼8文字です。 Valid PIN1 code is from 4 to 8 digit.
133Appendix/TroubleshootingPIN1コードの変更はPINロックが設定されているときに可能です。To change the PIN1, PIN must be locked. Switch PIN unblocking to PIN blocking.PINロック解除コードが違います。残り（○/10）回入力可能です。再入力してください。An incorrect PIN was imporperly entered 10 times in a row. Available functions will be limited. Please enter the contact unblocking PIN codeSMS送信に失敗しました。 You may be out of service or available network.You may encounter problems due to the network error.PIN1ロック解除コードがブロックされているためFOMAカードを使用できません。顧客センターにお問い合わせください。You are no longer able to use FOMA card that PIN unblocking code has been improperly entered10 times in a row. Please contact DOCOMO shop.FOMA端末の初期化に失敗しました。FOMA端末をリセットしてください。Communication may fail and the FOMA terminal cannot be properly recognized, if the PC is started up or restarted with the FOMA terminal left inserted in it. In this case, remove and reinsert the FOMA terminal. If communication fails even after the FOMA terminal is inserted again, remove it once, restart the PC, then insert the FOMA terminal into the PC again.送受信データなし。待ち受けモードに入ります。When no data transmission has been incurred for a certain period of time. Communication will be resumed when data transmission is incurred, so stay as it is.Error Messages Description
135Appendix/Troubleshooting■ Replacement partsBasically, replacement parts (parts required to maintain product function) will be kept in stock for at least 4 years after termination of production. Please note that the product may not be repaired even during this period, depending on the malfunctioning parts due to a shortage of those parts. Depending on the nature of the required repairs, it may still be possible to repair your terminal even after this period. Contact ″Repairs″ listed on the back of this manual.Pay attention•Do not modify the FOMA terminal, the FOMA card or its accessories.- Fire, injury or damage may result. - If the FOMA terminal is modified (part replacement, modification, painting, etc.), it will be repaired only after the modified parts have been restored to the condition at the time of purchase. However, repair may be refused depending on the nature of modification.･ Using sticker to decorate the FOMA terminal.･ Exchanging the packing with those other than DOCOMO product.- Repair of failures or damage caused by modification are charged even during the warranty period.•Do not remove any inscription stickers attached to the FOMA terminal. The inscription stickers certify that the FOMA terminal satisfies specific technical standards. If stickers are removed intentionally or are reattached in such a way that confirmation of the sticker's contents is impossible, repair or servicing may be refused because confirmation of whether or not the device conforms to relevant technical standards cannot be made.Updating softwareDownload the modification file of FOMA terminal from download site on the Internet and then update the software. If software update is necessary, you will be informed at the DOCOMO web site with "お知らせ（Information）".Note•Do not unplug the FOMA terminal with the computer during software update.•Software update (downloading and rewriting) may take a while.•If software update fails, all operations become unavailable. In this case, bring your FOMA terminal to a DOCOMO service center.
136 Appendix/TroubleshootingMain specifications■ Operation systemWindows 2000 Professional Japanese version(Service Pack 4 or later)Windows XP Home Edition Japanese version(Service Pack 2 or later)Windows XP Professional Japanese version(Service Pack 2 or later)Windows Vista 32 bit Japanese version (Service Pack1 or later)Windows Vista 64 bit Japanese version (Service Pack1 or later)Mac OS X 10.4.11 Japanese versionMac OS X 10.5.6 Japanese version■ Communication SpeedPacket Communication:Maximum receiving: 7.2Mbps（Best effort）Maximum sending: 5.7Mbps（Best effort）※ The maximum speed of 7.2Mbps for receiving and 5.7Mbps for sending is theoretical values and does not show the actual ones.The actual communication speed depends on communication environment and network congestion. ※ Out of High-Speed area, the maximum communication speed for receiving and sending is 384kbps■ Operating environmentTemperature：5℃∼35℃Humidity：45%∼85%■ Power sourcePower voltage DC5V±5%(Supplied from PC)Max Current consumption Max Current consumption while communicating 3G: Approx. 550mA or below GSM/GPRS: Approx. 300mA or below Average Current consumption while communicating 3G: Approx. 180mA or below GSM/GPRS: Approx. 170mA or below Average Current consumption while Standby: 3G: Approx. 90mA or below GSM/GPRS: Approx. 90mA or below※ Depending on the usage, power consumption fluctuates.■ Form factorUSB connection type■ DimensionsHeight: approx. 80mmWidth: approx. 32mmDepth: approx. 13mm■WeightApprox. 37g
137Appendix/TroubleshootingExport Controls of the Productand AccessoriesJapan Export Control Regulations (″Foreign Exchange and Foreign Trade Law″ and relevant laws and regulations) and U.S. Reexport Regulations (Export Administration Regulations: EAR) apply to this product and its accessories. If you export or re-export this product or its accessories, please follow the necessary procedures at your own risk and expense. For details on the procedures, contact the Ministry of Economy, Trade and Industry or the U.S. Department of Commerce.European Union Directives ConformanceStatementHereby, LG Electronics, Inc. declares that this product is in compliance with:•The essential requirements and other relevant provisions of Directive 1999/5/EC•All other relevant EU DirectivesThe above gives an example of a typical Product Approval Number.FCC RegulationsStatementThis equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•Reorient or relocate the receiving antenna.•Increase the separation between the equipment and receiver.•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.•Consult the dealer or an experienced radio/TV technician for help. Change or Modifications that are not expressly approved by the manufacturer could void the user's authority to operate the equipment. 0168
138 Appendix/TroubleshootingClass B Compliance This device and its accessories comply with part15 of FCC rules.Operation is subject to the following two conditions:•This device & its accessories may not cause harmful interference.•This device & its accessories must accept any interference received, including interference that may cause undesired operation.Body-worn OperationThis device has been tested for typical body-worn operations with the distance of 0.19inches (0.5cm) from the user's body. To comply with FCC RF exposure requirements, a minimum separation distance of 0.19inches(0.5cm) must be maintained from the user's body.Consumer Information on SAR (Specific AbsorptionRate)THIS DEVICE MEETS THE GOVERNMENT'S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES.Your wireless device is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications 'Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies.The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg.※ Tests for SAR are conducted using standard operatingpositions specified by the FCC with the devicetransmitting at its highest certified power level, the actualSAR level of the device while operating can be well belowthe maximum value. This is because the device isdesigned to operate at multiple power levels so as to useonly the power required to reach the network. In general,the closer you are to a wireless base station antenna, thelower the power output.Body-worn Operation This Mobile Broadband USB Modem, model L-05A, is approved for use in normal size laptop computers only (typically with 12" or larger display screens). To comply with FCC RF exposure requirements, this modem should not be used in configurations that cannot maintain at least 5mm (approximately 0.2 inches) from users and bystanders, and 12mm (approximately 0.47 inches)from the top of the USB modem. This USB modem has been tested for compliance with FCC/IC RF exposure limits in the laptop computer(s) configurations with horizontal and vertical USB slots and can be used in laptop computers with substantially similar physical dimensions, construction, and electrical and RF characteristics. This USB modem must not be used with any other antenna or transmitter that has not been approved to operate in conjunction with this modem.
139Appendix/TroubleshootingBefore a device is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government-adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., worn on the body) as required by the FCC for each model.The highest SAR value for this device when worn on the body is 1.17W/kg.The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF emission guidelines. SAR information on this device is on file with the FCC and can be found under the Display Gant section of http://www.fcc.gov/ after searching on FCC ID BEJL05A. Additional information about Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications Industry Association (CTIA) web-site at http://www.wow-com.com.Intellectual Property RightsCopyrights and Rights of PortraitWithout permission of the copyright owner you may not duplicate, modify, transmit over public communication lines, etc. any document, image, music, software, or other content owned by a third party that you have used this product to download from an Internet web site, etc., except for private uses such as duplication and indexing that are allowed by copyright law.1.3W/kg.

Navigation menu