LG Electronics USA L05A 850/ 1900 GSM/ GPRS/ EDGE and 850 WCDMA USB Dongle User Manual L05A Manual E

Download:
Mirror Download [FCC.gov]
Document ID	1100756
Application ID	ydy7G9XWFO5rjOYNM3swTg==
Document Description	Users Manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	265.13kB (3314173 bits)
Date Submitted	2009-04-23 00:00:00
Date Available	2009-07-20 00:00:00
Creation Date	2009-04-23 14:00:48
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2009-04-23 14:01:17
Document Title	L05A_Manual_E.book
Document Creator	FrameMaker 7.0
Document Author:	Administrator

Part 15.21 statement
" Change or Modifications that are not expressly approved by the manufacturer could void
the user's authority to operate the equipment. “
Part 15.105 statement
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Part 15 Class B Compliance
This device and its accessories comply with part15 of FCC rules.
Operation is subject to the following two conditions:
(1) This device & its accessories may not cause harmful interference.
(2) This device & its accessories must accept any interference received,
including interference that may cause undesired operation.
Body-worn Operation
This Mobile Broadband USB Modem, model L-05A, is approved for use in normal size laptop
computers only (typically with 12" or larger display screens). To comply with FCC RF exposure
requirements, this modem should not be used in configurations that cannot maintain at least
5mm (approximately 0.2 inches) from users and bystanders, and 12mm (approximately 0.47 inches)
from the top of the USB modem.
This USB modem has been tested for compliance with FCC/IC RF exposure limits
in the laptop computer(s) configurations with horizontal and vertical USB slots and can be
used in laptop computers with substantially similar physical dimensions, construction,
and electrical and RF characteristics.
This USB modem must not be used with any other antenna or transmitter that has not been
approved to operate in conjunction with this modem.
DOCOMO W-CDMA・ GSM/GPRS
System
Thank You for Purchasing the「Data Communication Device L-05A」
Before or while using the L-05A, be sure to thoroughly
read this manual and the individual manual for other
operation devices to ensure its correct use. For further
information, contact the "docomo Information Center" on
the back of this manual. The L-05A is designed to be your
close partner. Treat it carefully at all times to ensure
longterm performance.
Before Using the FOMA Terminal
• Because the FOMA terminal uses radio waves, it may not
function in locations where it is difficult for radio waves to
penetrate, such as tunnels, underground passages and some
buildings in areas where radio wave signals are weak or out of
the service area. Even when you are on a higher floor of a tall
building or condominium and nothing blocks your view outside,
the FOMA terminal may not be able to receive or transmit
signals. Also communication may be interrupted even when the
Antenna Indication Lamp on the FOMA terminal lights green
indicating a strong signal reception with 3 antenna indication
bar.
• Use the FOMA terminal in ways that do not disturb others in
public places, crowded locations, or quiet locations.
• The FOMA terminal communicates via radio waves by
converting voices into digital signals. If you move into an area
where signal reception is poor, the digital signals may not be
accurately decoded and what you hear may differ slightly from
what was actually said.
• DOCOMO is not responsible for any economic losses incurred
through lost communication opportunities caused by external
factors such as malfunction or failure of the FOMA terminal, or
electrical outage.
• The FOMA terminal can be operated in FOMA Plus-Areas and
FOMA HIGH-SPEED Areas.
• The FOMA terminal can be used only via the FOMA network
provided by DOCOMO and DOCOMO's roaming area.
• This FOMA terminal does not support i-mode functions (i-mode
mail, connection to official i-mode sites or i-αppli, etc.)
For Those Who Use the FOMA Terminal
for the First Time
If this is the first time for you to use the FOMA terminal, it
is recommended that you read this manual in the following
order to learn basic operations.
1. Learning the precautions. . . . . . . . . . . . . . . . . . . . . . . P7
2. Learning the names of parts and functions of the
FOMA terminal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P18
3. Inserting the FOMA terminal into a PC . . . . . . . . . . P24
4. Having the FOMA terminal recognized by your PC. . . P24
5. Setting up the FOMA terminal for communication. . . . P66
The latest version of this manual can be downloaded from the
DOCOMO web site.
■ The URL of PDF for Instruction Manual
http://www.nttdocomo.co.jp/english/support/manual/
index.html
※ The URL and the information contained in the manual are
subject to change without prior notice.
How to Read/Refer to This Manual
Contents
L-05A Manual is composed of『L-05A Instruction Manual∼Connection Guide∼』and 『L-05A INSTRUCTION MANUAL
(included CD-ROM)』(this manual) recorded in CD-ROM.
■『L-05A Instruction Manual∼Connection Guide∼』
The following contents such as connection to computer, troubleshooting methods, specifications of L-05A are written.
• Contents/Precautions
• Before Using the FOMA Terminal
• Setting up
• Appendix/Troubleshooting
■『L-05A INSTRUCTION MANUAL (included CD-ROM)』
（this manual）
Besides the above contents described in『L-05A Instruction Manual∼Connection Guide∼』, the contents of configuring
communication through special application are also written.
This manual is supplied with PDF. To view this manual, Adobe Reader (Version6.0 or later is recommended) is necessary.
• L-05A Connection Software
• DOCOMO Connection Manager
• Configuring Network Manually
• Overseas Use
How to Refer to This Manual
This manual offers you the following methods to easily find a page describing functions or services you want to know
about.
From the Index
P141
Search from the index when you know the names of functions or
services.
From the Tabs on the Cover
Front
cover
See next
page for
detailed
descriptions
Search functions or services from the index tabs printed on the
front cover.
From the Contents
P5
Search from the contents that categorize functions.
From the Main Features
P6
Search from the features when you want to use specific functions.
･
･
･
･
Please understand that「L-05A Manual」refers to the「L-05A」as the「FOMA Terminal」.
This manual describes, some steps and screens may differ depending on your operating environment.
Reprinting all or parts of this manual is prohibited.
Information contained in this manual is subject to change without prior notice.
A way to find a destination page is explained with an example of installing L-05A connection software on Windows
(including a driver).
From the
Index
P141
P35
The page describing
installation of L-05A
connection software
on Windows
(including a driver)"
Search or a function
name or a service
name as shown
below.
From the
Index Tabs
on the Front
Cover
Front cover
Search for the
function in the order
of "Front cover"→
"Chapter title page"→
"Target page" as
shown below.
Displays a
section title.
Explains
Operation steps
Useful
Information or
suggestions
relating to an
operation.
A key screen for an
operation step.
This is an image of
a screen seen on
the PC. Numbers,
settings or
characters entered
are for reference
only.
※：The above page is an example.
※：Screen images and illustrations contained in this manual
are for reference only. They may differ from those seen for
the actual product.
Index:
Searching each
chapter is available.
Contents
How to Read/Refer to This Manual ･･････････････････ 1
Contents ････････････････････････････････････････････ 5
Features of the L-05A･･･････････････････････････････ 6
Safety Precautions (ALWAYS FOLLOW THESE
PRECAUTIONS) ･････････････････････････････････････ 7
Configuring
Network
Manually
89
Handling and Care･････････････････････････････････ 12
Purchased Product and Accessories ･･････････････ 15
Before Using
the FOMA
Terminal
17
Names of Parts and Functions
Using FOMA Card
Available Communications
Connecting FOMA Terminal with a PC
Setting Up
31
Setting Up
Windows version
Macintosh version
L-05A
Connection
Software
49
L-05A Connection Software
Using Packet Communication
Using SMS
Using Phonebook
Using Application Option
DOCOMO
Connection
Manager
77
DOCOMO Connection Manager
Windows version
Macintosh version
Configuring Dial-up Network Manually
Conducting Communication
(Connecting Dial-up)
Overseas
Use
111
International Roaming Service
(WORLD WING)
Services Available Overseas
Confirming before Using Overseas
Setting the Searching Method for
Available Networks
Configuring Network
Appendix/
Troubleshooting
119
AT Commands
AT Command List
Troubleshooting
Error Messages
Warranty and After-Sales Service
Software update
Main Specifications
Export Controls of the Product and
Accessories
Intellectual Property Rights
Index
Contents/Precautions
Features of the L-05A
FOMA (Freedom Of Mobile multimedia Access) is the name of a service provided by DOCOMO based on the W-CDMA
system, which is certified as one of the global standards of 3rd generation mobile communication systems (IMT-2000).
■ Correspondence with the FOMA HIGH-SPEED Area
You can enjoy high speed communication (Best effort
system）at a maximum of 7.2Mbps for receiving and
5.7Mbps for sending.
• The maximum speed of 7.2Mbps for receiving and
5.7Mbps for sending are theoretical values and they do
not show the actual performance.
• Out of High-Speed area, the maximum communication
speed for receiving and sending is 384kbps.
• The actual communication speed varies depending on
surrounding communication conditions and network
condition.
• DOCOMO offers Internet connection services, such as
「mopera U」. For details, visit the mopera U web site
http://www.mopera.net/ (Japanese only)
※ The packet communication in FOMA HIGHSPEED area,
the amount of send/receive data is expected to increase.
Note that the communication fees may become high.
■ International Roaming Service
Communications are available from a PC even in foreign
countries that have adapted the W-CDMA (3G) network
system or GPRS network. P112
※ If you subscribed to the FOMA service after September
1, 2005, a separate subscription is not required.
However, if you unsubscribed to the FOMA service
subscription or canceled the service, a separate
subscription is required.
※ If you initially subscribed to the FOMA service before
August 31, 2005, and have not subscribed to "WORLD
WING", a separate subscription is required.
※ This service is not available with some billing plans.
■ FOMA Card Interchangeability
The same FOMA card can be used in more than one
FOMA terminal. P19
■ SMS Feature
Allows you to send and receive SMS by using L-05A
Connection Software P54
Contents/Precautions
■ The following symbols indicate special warnings
regarding product usage.
Safety Precautions (ALWAYS
FOLLOW THESE PRECAUTIONS)
■ Before using your FOMA terminal, read these ″Safety
Precautions″carefully so that you can use it properly.
After reading the safety precautions, keep this manual in
a safe place for later reference.
■ These precautions are intended to protect you and
others around you. Read and follow them carefully to
avoid injury, damage to the product or damage to
property.
■ The signs below indicate the levels of danger or damage
that may occur if the particular precautions are not
observed .
DANGER
This sign indicates that
incorrect handling has a
high possibility of
causing death or serious
injury.
WARNING
This sign indicates that
incorrect handling poses
a risk of causing death or
serious injury.
CAUTION
This sign indicates that
incorrect handling poses
a risk of causing injury or
damage to the product or
property.
Denotes things not to do (prohibition).
Denotes not to disassemble.
Not disassembly
Not liquids
Denotes not to use where it could get
wet.
Denotes mandatory instructions
(matters that must be complied with).
■ "Safety Precautions" are explained in the following
4 sections.
General Precautions for the FOMA Terminal and FOMA
Card ………………………………………………………………… 8
Precautions for the FOMA Terminal ……………………… 9
Precautions for the FOMA Card ………………………… 10
Notes on Using near Electronic Medical Equipment …… 11
Contents/Precautions
General Precautions for the FOMA
Terminal and FOMA Card
Do not use or leave the FOMA terminal
and FOMA card in places with a high
temperature such as in cars under the
blazing sun.
Deformation, malfunction heating or the
deterioration of performance may result.
Also, part of the case could get heated,
causing bare skin burns.
Not disassembly
Not liquids
Do not disassemble Disassemble,
remodel or solder the terminal and FOMA
card.
Fire, injury, electric shock or malfunction
may result.
Do not let FOMA terminal and FOMA
card get wet.
Contact with water or other liquids may
cause heating, electric shock, fire,
malfunction or injury. Take care not to
use the terminal and FOMA card in areas
where they could get wet.
Contents/Precautions
WARNING
Do not put the FOMA terminal or FOMA
card in microwave ovens or other heating.
The FOMA terminal may over heat, smoke
or catch fire, or its circuit parts may burst.
Do not throw the FOMA terminal or FOMA
card, or subject them to severe shocks.
Malfunction or fire may result.
Be careful not to let electro conductive
materials (metal pieces, pencil leads etc.)
contact with the connector terminal. Also,
make sure that these are not entered into
the inside of the FOMA terminal.
Fire or other malfunctions may result from
a short circuit.
Make sure you have the power of the
computer which is connected with FOMA
terminal switched off before you go near a
flammable gas such as gasoline fumes.
Using the terminal in such an environment
may result in a fire.
CAUTION
Do not place the FOMA terminal or FOMA
card on unstable locations such as wobbly
tables or slanted locations.
The FOMA terminal or FOMA card may fall,
resulting in injury or malfunction.
Do not store the FOMA terminal or FOMA
card in humid or dusty places, or in hot
areas.
Malfunction may result.
If children use the FOMA terminal or
FOMA card, a guardian should explain the
precautions and correct operations. The
guardian should also make sure that the
instructions are followed during use.
Injury may result.
Keep out of reach of babies and infants.
Accidental swallowing or injury may result.
Precautions for the FOMA Terminal
WARNING
Do not put the FOMA terminal in the place
where it could be affected by an expanded
airbag, e.g. on the dashboard.
If the airbag expands, the FOMA terminal
could hit you and others, causing
accidents such as injury and the FOMA
terminal could get malfunction or
damaged.
Do not place the terminal in breast or
inner pocket when electronic medical
equipment is near by.
Using FOMA terminal closed to electronic
medical equipment may result malfunction.
Do not allow liquids such as water, or
foreign materials such as metal pieces or
flammable materials to get into the FOMA
card opening in the FOMA terminal.
Fire, electronic shock or malfunction may
result.
Contents/Precautions
Turn off the FOMA terminal in places
where use is prohibited such as airplanes
or hospitals.
Electronic and electronic medical
appliances may be adversely affected.
For use inside medical facilities, make sure
that you comply with their regulations.
Remove FOMA terminal from the USB port
in places near high-precision electronic
devices or devices using weak electronic
signals.
The FOMA terminal may possibly cause
these devices to malfunction.
※ Electronic devices that may be affected
Hearing aids, implanted cardiac pacemakers,
implanted defibrillators, other medical
electronic devices, fire alarms, automatic
doors and other automatically controlled
devices.
If you are using an implanted cardiac pace
maker, implanted defibrillator or any other
electronic medical device, consult the
manufacturer or retailer of the device for
advice regarding possible effects from radio
waves.
CAUTION
Electronic devices in some types of cars
can be affected by use of the FOMA
terminal.
For safety's sake, do not use the FOMA
terminal inside such cars.
Itching, rash or eczema may be caused
depending on your physical conditions or
predisposition.
If an abnormality occurs, stop using the
FOMA terminal immediately, and then seek
medical attention.
Metal(chrome plating) is used to the
following parts.
Parts that are used: USB connector
Precautions for the FOMA Card
CAUTION
Be careful when removing the FOMA
card(IC portion).
Your hands or fingers may be injured.
10
Contents/Precautions
Notes on Using near Electronic Medical
Equipment
■The description below meets ″Guideline on the
Use of Radio-communication Equipment such as
Cellular Telephones - Safeguards for Electronic
Medical Equipment″ by the Electromagnetic
Compatibility Conference.
WARNING
Be sure to adhere to the following
regulations inside medical facilities.
●Keep the FOMA terminal out of operating
rooms, intensive care units (ICUs) or
coronary care units (CCUs).
●Turn off the PC in hospital wards.
●Turn off the PC in hospital lobbies and
corridors if electrical medical devices
could be nearby.
●If the medical facility has specific zones
where use or possession of mobile
terminals is prohibited, follow those
regulations.
●If the function which automatically turns
on the power is set, cancel the setting
before turning off your PC.
Turn off the PC in crowded trains or other
public places where implanted cardiac
pacemaker or defibrillator wearers could
be nearby.
Signals from the FOMA terminal may
affect the operation of implanted cardiac
pacemakers or defibrillators.
If you use an implanted cardiac
pacemaker or implanted defibrillator, use
the mobile terminal 22cm or more away
from the implanted cardiac pacemaker or
implanted defibrillator.
Operation of an implanted cardiac
pacemaker or implanted defibrillator may
be affected by radio waves.
Patients using electronic medical
equipment other than implanted cardiac
pacemakers or implanted defibrillators
(using outside medical facilities for
treatment at home, etc.) should check the
influence of radio waves upon the
equipment by consulting the
manufacturer.
Operation of electronic medical equipment
may be affected by radio waves.
Contents/Precautions
11
Handling and Care
General Usage Guidelines
■Keep the FOMA terminal away from water.
The FOMA terminal and FOMA card are not
waterproof. Do not use the terminal in places with
high humidity such as a bath or where rain may
get it wet. If you carry the card close to your body,
moisture from sweat may corrode the internal
parts causing a malfunction. Note that
malfunctions deemed to be caused by water are
not covered by the warranty, and may be
impossible to repair. Since these malfunctions are
not under warranty, even when repair is possible,
it will be done at the user's expense.
■Clean the FOMA terminal with a dry, soft cloth
(Lens cleaning cloth).
If the FOMA terminal is wiped with alcohol, paint
thinner, benzine or detergent, the printing may
disappear or color may fade.
■Keep the connector contacts clean with a dry,
soft cloth.
Dirty contacts can result in intermittent
connections.
12
Contents/Precautions
■Do not place the equipment near air conditioner
outlets.
Condensation may form due to rapid changes in
temperature, and this may corrode internal parts
and cause malfunction.
■Do not place the FOMA terminal where excessive
force will be applied to it.
If FOMA terminal is inserted to a full bag, or
placed in a pocket and sat on, its internal PCBs
may be damaged or malfunction. Such damage is
not covered by warranty.
■Read the individual manual attached to the FOMA
terminal.
FOMA Terminal
■Avoid using in extremely high or low
temperatures.
The FOMA terminal should be used within a
temperature range from 5 °C to 35 °C and a
humidity range from 45 % to 85 %.
■FOMA terminal may affect fixed phones,
televisions or radios in use nearby. Use as far as
possible from such appliances.
■Keep a separate record of any information stored
on the FOMA terminal and store the copies in a
safe location.
DOCOMO assumes no responsibility for the loss
of any of your data.
■Remove the FOMA terminal from the PC when
transporting.
Malfunction or damage may result.
■It is normal for the FOMA terminal to become
warm during use. You can continue to use it even
when it is warm.
■Take care not to drop the FOMA terminal when
removing the FOMA terminal from the carrying
case.
■When it is not in use, keep the FOMA terminal in
its carrying case to keep the connector contacts
clean.
Dirty contacts may result in intermittent
connections.
■When putting the FOMA terminal in carrying case,
keep it away from wet or high temperature place.
Pay attention not to put excessive force on the
FOMA terminal.
Transformation, tarnish, color staining may result.
FOMA Card
■Do not put excessive force on the FOMA card
when inserting or removing it into the FOMA
terminal.
■It is normal for the FOMA card to become warm
during use. You can continue to use it even when
it is warm.
■Always keep the IC portion of the FOMA card
clean.
■Clean the FOMA card with a soft, dry cloth (Lens
cleaning cloth).
■Be sure to keep a separate note of the
information registered to the FOMA terminal.
DOCOMO is not responsible for any losses of
registered information.
■Visit DOCOMO shop to return the FOMA card for
the environmental purpose.
■Avoid extreme temperature.
■Do not scratch, touch carelessly or short circuit
the IC portion.
Data loss or malfunction may result.
■Do not drop or give shock to the FOMA card .
Malfunction may result.
■Do not bend or put heavy things on the FOMA card.
Malfunction may result.
■Do not insert UIM into the FOMA terminal with
labels or stickers attached on.
Contents/Precautions
13
CAUTION
■Do not use the modified FOMA terminal. Using
modified FOMA terminal result in violating the law
of Electromagnetic Compatibility.
FOMA terminal has been complied with technical
standard of wireless equipment stipulated by law
of Electromagnetic Compatibility. As for the proof,
the technical standard compliance mark, is
indicated in the inscription seal. If FOMA terminal
is modified by turning the screw to the left to
disassemble, technical standard compliance
becomes invalid.
Please do not use FOMA terminal during the time
when technical standard compliance is being
invalid, since you are in violation of the law of
Electromagnetic Compatibility.
14
Contents/Precautions
Purchased Product and Accessories
■ L-05A Terminal (With Rear Cover L13, Warranty)
■ L-05A CD-ROM
• L-05A Connection Software (For Windows/Macintosh）
• DOCOMO Connection Manager (For Windows/Macintosh）
• L-05A INSTRUCTION MANUAL（PDF）
■ L-05A Instruction Manual∼Connection Guide∼
※
Software specifications are subject to change without
prior notice.
■ USB Extension Cable (Sample)
Use when "USB Extension Cable" is written in this manual.
■ Carrying Case (Sample)
■ Mounting folder (Sample)
Use when "A mounting Folder" is written in this manual.
Contents/Precautions
15
Before Using the FOMA Terminal
Names of Parts and Functions･･･････････････････
Using a FOMA Card･･････････････････････････････
Available Communications ･･･････････････････････
Connecting FOMA Terminal to a PC ･････････････
18
19
23
24
17
Names of Parts and Functions
Examples of a
a USB Connector→P25
Ex. 1:
Connection contacts to a PC.
※Pull out from the FOMA terminal and use.
The tip part of the USB connector is able to turn 90 degree.
However, only one direction is available to turn.
b Antenna Part
The antenna is inside the FOMA terminal.
c PWR Lamp→P19
Indicates the power supply conditions.
d IDLE/BUSY Lamp→P19
Indicates the FOMA terminal status.
18
Before Using the FOMA Terminal
Ex. 2:
Mode Indication Lamp
Using a FOMA Card
The FOMA card is an IC card that stores personal
information such as your phone number. Without a FOMA
card installed in the FOMA terminal, you cannot use data
communication. For detailed information, refer to FOMA
Card Manual.
Inserting/Removing
Inserting
※ Operation indicating lamp
aPower
Indication
Lamp
bMode
Indication
Lamp
Green
Green
Attempting to
communicate
Green
Blue
(Flash)
Communicating
Green
Blue
While receiving
Green
(Flash)
Green
FOMA Terminal Status
When powered on
Waiting to connect to the FOMA
network
Packet
communication
SMS
PIN
Opening SMS
Green
Green
Sending SMS
Green
Green
PIN Lock
Green
Waiting to unlock
PIN1
Green
Inserting the UIM with two hands.
While pushing the cover in the direction of a,
slide the rear cover in the direction of b. Lift
the cover as shown by c.
Rear Cover
Before Using the FOMA Terminal
19
b
Insert the UIM into slot at the direction of
arrow with the IC chip side down
Removing
Remove the UIM with two hands.
IC is faced
FOMA card
Notch
FOMA card slot
While pushing the cover in the direction of a,
slide the rear cover in the direction of b. Lift
the cover as shown by c.
Fit the rear cover to the ditch of FOMA
terminal at approximately 3mm from the top
tip of the FOMA terminal. While pressing along
direction b, slide the rear cover along
direction a till hear rear cover clicked.
Approx.3mm
20
Before Using the FOMA Terminal
Rear Cover
Slide the UIM in the direction of arrow and
remove it from the FOMA Card slot.
FOMA card
c
Fit the rear cover to the ditch of FOMA
terminal at approximately 3mm from the top
tip of the FOMA terminal. While pressing along
direction b, slide the rear cover along
direction a till hear rear cover clicked.
Approx.3mm
Note
• Make sure not lose the removed FOMA card.
• Make sure to check the direction of FOMA card.
IC
• Be careful not to scratch FOMA card's IC parts.
• Inserting FOMA card in the reverse direction may cause
malfunction.
• Inserting and removing FOMA card with an excessive force
may cause damage to your FOMA card.
• Do not remove FOMA card while FOMA terminal is inserted
to a PC, it may causes damage to your FOMA card.
PIN1 Code
You can set PIN codes (Personal Identification Number)
for FOMA Card. The default setting for the PIN1 code is
"0000". The PIN1 code is a 4 to 8-digit security code to be
entered every time the FOMA terminal is turned on for user
verification to prevent any unauthorized use by others.
If your FOMA card is set to require a PIN1 code, data
communication cannot be performed until the PIN1 is
entered. Start the L-05A High Speed Utility and verify
the PIN1 code, or set (P69)not to verify the PIN1 code
in advance.
■ Changing the PIN1 Code
You can change the PIN1 code to any number. To
prevent any unauthorized use by third parties, change it
to your own number. If you improperly enter the PIN1
code 3 times in a row, further entry is locked
automatically (PIN lock), so be sure to keep a separate
note of the numbers you set.
• Entering PIN1 Code/ Changing PIN1 code→P70
■ PIN Unblocking Code
The PIN Unblocking Code is the number used to unblock
the PIN1 code. You are notified of your PIN Unblocking
Code when you purchase your FOMA terminal. Entering
the Unblocking Code (8-digit) unblocks the PIN lock.
If you improperly enter the Unblocking Code 10 times in a
row, the FOMA card locks automatically, so be sure to
keep a separate note of the number.
Before Using the FOMA Terminal
21
Start up L-05A Connection Software
The PIN1 code Verification screen appears
Enter PIN1 Code
Incorrect entry 3 times in a row
Enter Unblocking PIN Code
OK
You can set a new
PIN1 code
Incorrect entry 10 times in a row
Contact a DOCOMO shop
FOMA Card Types
Please be aware that the FOMA card (Blue) has different
functions from the FOMA card (Green/White) as follows:
Function
FOMA card
(Blue)
The number of digits of a
phone number that can be
saved to the FOMA card
Phonebook
Up to 20 digits
WORLD WING
Not available
FOMA card
(Green/White)
Up to 26 digits
This terminal allows
up to 20 digits.
Available
WORLD WING
WORLD WING is DOCOMO's FOMA international roaming
service that provides telephone and other types of mobile
communications. It allows the subscriber to use the
same phone number overseas as in Japan by inserting a
FOMA card(green/white) into a FOMA terminal or a
mobile phone designed for overseas use.
• If you subscribed to the FOMA service after September 1,
2005, a separate subscription is not required. However, if
you unsubscribed to the FOMA service subscription or
canceled the service, a separate subscription is required.
• If you initially subscribed to the FOMA service before
August 31, 2005 and have not subscribed to "WORLD
WING", a separate subscription is required.
• This service is not available with some billing plans.
• Your FOMA card (green/white) is lost or stolen overseas,
contact DOCOMO immediately and temporarily suspend
your subscription. For contact information, see "docomo
Information Center" on the back of this manual. Call and
communication charges after the terminal was lost or
stolen are still charged to you.
22
Before Using the FOMA Terminal
Note
Available Communications
Packet Communication
Fees for this communication method are based on the
amount of exchanged data. You can perform data
communication at a maximum of 7.2Mbps for receiving and
5.7Mbps for transmitting by using a connection that allows
FOMA communication such as 「mopera U」, one of
DOCOMO's Internet connection services.
• Communication fees become high when performing
communications with large amount of data such as
browsing websites with many graphics or downloading
data.
• Data communication fees under international roaming
differ from those in Japan.
• FOMA terminal does not support 64K data
communication.
• This FOMA terminal does not support Remote Wakeup.
• This FOMA terminal does not support FAX communication.
※ The maximum speed of 7.2Mbps for receiving and 5.7Mbps
for sending is theoretical values and does not show the
actual ones. The actual communication speed depends on
communication environment and network congestion.
• You can perform communication using international roaming
under「mopera U」
• Out of High-Speed area, the maximum communication speed
for receiving and sending is 384kbps.
• The communication speed varies depending on the access
point and radio wave status.
• The communication speed varies depending on the access
point under international roaming.
• Use the「DOCOMO Connection Manager」in the CD-ROM to
check the approximate number of transmission bytes and
charges under the communication.
Before Using the FOMA Terminal
23
Usage Notes
■ Internet service provider fees
Fees to an Internet service provider may be required to
connect to the Internet. These fees are added to the
FOMA service fees and are paid to your Internet service
provider directly. For details on connection fees, contact
your Internet service provider.
You can subscribe to such as「mopera U」, one of
DOCOMO's Internet connection services. Charge for
subscribing 「mopera U」is required.
For service and connection/settings of 「mopera」, visit
the「mopera」web site.
http://www.mopera.net/mopera/index.html (Japanese
only)
■ User authentication to access networks
Depending on the access point, user authentication (ID
and password) may be required to connect. If required,
enter the ID and password from the dial-up network. The
ID and password will be provided by the network
administrator of your Internet service provider or the
access point. For details, contact your provider or access
point network administrator.
■ Requirements for packet communication
The following conditions must be met to perform
communications using the FOMA terminal. However, a
connection may not be established if traffic is heavy at
the base station or if radio signals are weak.
• The FOMA terminal must be in a FOMA network or
DOCOMO's roaming service area.
• The access point corresponds to the FOMA packet
communication.
24
Before Using the FOMA Terminal
Connecting FOMA Terminal to
a PC
When connecting FOMA terminal with computer for the
first time, it is required to install L-05A connection
software (including a driver).
For installing L-05A connection software, refer to the
followings.
• For Windows: "Preparation for using L-05A" (P35)
• For Macintosh: "Preparation for using L-05A" (P42)
Inserting
Turn on a PC
Connecting the FOMA terminal with a PC
■ When using a mounting folder and a USB extension
cable
• Use a mounting folder and a USB extension cable to fix
on the top of a PC
aPull out the projection part of USB connector 180
degree by fingertip
cPut the FOMA terminal between the mounting folder
and fix on the top of the PC
PC
Mounting folder
Projection
part
bHold the connector part of USB extension cable and
insert into the USB connector near the FOMA terminal
along arrow direction
dHold the connector part of USB cable and insert into PC
USB port along arrow direction
USB connector
USB port
USB extension cable
USB extension
cable
Before Using the FOMA Terminal
25
cInsert the USB connector of FOMA terminal into a PC
USB port
■ When connecting with a PC directly
• Insert the FOMA terminal into a PC USB port and use it
directly.
• The USB connector of FOMA terminal is able to turn 90
degree complying to directions of USB port
aPull out the projection part of USB connector 90
degree by fingertip
USB connector
USB port
• It is available to use without turning USB connector 90
degree as the above-mentioned procedure b.
Projection
part
•
USB connector
bThe FOMA terminal body turn the tip part of USB
connector 90 degree as shown in the illustration
USB port
Note
USB connector
• Refrain from turning the FOMA terminal after inserting USB
connector into PC USB port.
Malfunction or damage may result when subject the FOMA
terminal to severe shocks due to carelessness.
26
Before Using the FOMA Terminal
c
Start communication connecting
Removing
Note
End data communication
Remove the FOMA terminal
Power Indication lamp
Mode Indication Lamp
• Confirm whether power indication lamp changes to red and
mode indication lamp changes to green.
• Using "L-05A connection software"→P49
• Using "DOCOMO connection manager"→P77
• Configuring manually (OS Standard)→P89
• If the L-05A connection software/DOCOMO connection
manager is already running, exit the L-05A connection
software/DOCOMO connection manager. Verify that data
connection is disconnected.
■ When using a mounting folder and a USB extension
cable
aHold the connector part of a USB extension cable and
pull out the FOMA terminal from PC USB port along
arrow direction
USB port
USB extension cable
Before Using the FOMA Terminal
27
bRemove the FOMA terminal along with the mounting
folder from the top of the PC. Remove the mounting
folder from the FOMA terminal
dPack the USB connector into the FOMA terminal
PC
Mounting
folder
USB
connector
■ When connecting to a PC directly
aHold the USB connector part of FOMA terminal. Pull out
the FOMA terminal straightly from PC USB port
cHold the connector part of the USB extension cable and
pull out from the USB connector near the FOMA
terminal along arrow direction
USB connector
USB connector
USB port
USB extension cable
28
Before Using the FOMA Terminal
bTurn the tip part of the USB connector 90 degree as
shown in the illustration
USB connector
cPack the USB connector into FOMA terminal
USB connector
Caution
• If you force to remove FOMA terminal and pull out the USB
extension cable, this may result malfunction.
• Removing FOMA terminal from USB connector during data
communication may suspend data communication and
result malfunction or data losses.
Before Using the FOMA Terminal
29
Setting up
Setting up ･･･････････････････････････････････････
Windows Version ････････････････････････････････
Macintosh Version ･･･････････････････････････････
32
35
42
31
Setting up
■ Data communication with L-05A
"Communication configuration file (Driver)" and "L-05A connection software" are required to install for a PC to recognize
the FOMA terminal. "Communication configuration file (Driver)" will be installed along with "L-05A connection software".
Although data communication is available with only L-05A connection software, if necessary using it after installing
DOCOMO connection manager in addition is also available.
Data communication is also available based on configuring manually after installing L-05A connection software.
■ Installation of L-05A connection software
Since L-05A has zero installation, when connecting the FOMA terminal to a PC for the first time, "L-05A connection
software" installation screen appears automatically. "Zero installation" is supported by the PC with Windows OS in it. If
zero installation works improperly, install L-05A connection software with the included CD-ROM.
In addition, although Macintosh does not support the zero installation feature, installation continues through the CDROM icon appears when connecting the FOMA terminal to a PC.
The procedure of setting up is described on the next page.
32
Setting up
Work Flow of Setting up
Preparing the included CD-ROM
・ Windows Version P38
・ Macintosh Version P45
Connecting the FOMA terminal with a PC
・ Windows Version P35
・ Macintosh Version P42
Installing L-05A connection software (Driver)
Confirmation after Setup
・ Windows Version P39/・ Macintosh Version P45
Using L-05A
connection
software
Operation configurations of L-05A
connection software P66
Communication connection with L-05A
connection software P50
Using DOCOMO
connection manager
Installing DOCOMO connection manager
・ Windows Version P79
・ Macintosh Version P83
Operatino configuration/communication
connection
with DOCOMO connection manager
『DOCOMO connection manager manual』
Configuring
manually(Only
Windows)
Communication configuring
manually P90
Communication configuring manually
with OS function P109
Setting up
33
Operating Environments
Using this FOMA terminal under the following operational
environments.
Item
PC Main
Unit
• Available CD-ROM drive to use from PC-AT
compatible.
• USB port (Comply with Universal Serial Bus
Specification Rev1.1/2.0)
• DOCOMO is not responsible for any
incompatibility of the operation performed
through the USB Hub (including USB port
available from the monitor, keyboard, etc.)
• Display resolution of 800×600 pixels, High
Color (65.536) or higher is recommended.
OS※1
Windows 2000 SP4 or later (Japanese versions)
Windows XP SP2 or later (Japanese versions)
Windows Vista SP1 or later (Japanese versions)
Mac OS X 10.4.11 (Japanese versions)※3
Mac OS X 10.5.6 (Japanese versions)※3
Required
Memory※2
Windows 2000 : 64Mbytes or more
Windows XP : 128Mbytes or more
Windows Vista : 512Mbytes or more
Mac OS X 10.4.11：512Mbytes or more
Mac OS X 10.5.6：512Mbytes or more
Hard Disk
Space※2
34
Requirement
Setting up
50Mbytes or more available space
※1 DOCOMO does not guarantee the operation under the
supported OS of the OS is changed through update.
※2 Required memory or available hard disk space may vary
depending on the system environment of a PC.
※3 Only Mac with CPU made by Intel Corporation is available.
For latest information of operation environment, visit
DOCOMO's "international web site"
Note
• The software may not work depending on the operating
system environment. DOCOMO does not guarantee any
operation other than the environment operation described
on the left side.
Preparation for Using L-05A
Windows Version
The L-05A connection software only need to be installed
when you connect the FOMA terminal to your PC for the
first time.
Note
• Do not remove the FOMA terminal while installing.
• Installation may take several minutes depending on the PC
you use.
• Do not install or uninstall during data communication.
• When installing, make sure to install from the account with
PC supervisor privileges. An error will occur during
installation if you install from the account without these
privileges.
• For details on setting up PC supervisor privileges, contact
your computer manufacturer or Microsoft Corporation.
Setting Zero Installation (Auto)
■ For Windows Vista
Connect the FOMA terminal with a PC
The setup screen of L-05A connection software is
automatically displayed by zero installation.
"自動再生" screen will be displayed depending on setting.If the
screen is displayed, check "ソフトウェアとゲームに対しては常に
次の動作を行う" and select "Launcher.exeの実行"
np
※ When the Setting up screen of L-05A connection
software is not automatically displayed, install with the
included CD-ROM (P38)
Setting up
35
b
Click "許可(Allow)" on "ユーザーアカウント制御
(User account control)" screen
Click "同意する (I Agree)"
Click "次へ(Next)"
Installation starts.
■ For Windows XP/2000
• Because "ユーザーアカウント制御(User account control)"
screen is not displayed, follow the next step
36
Click "次へ(Next)"
Setting up
f
Click [OK]
Confirm whether the FOMA terminal is
recognized by PC
On the lower right side of task tray, "デバイスドライバソフト
ウェアをインストールしています(Device driver software is being
installed)" message is displayed, and the FOMA terminal is
recognized automatically.
g Click "完了(Finish)"
If the FOMA terminal is recognized properly, "デバイスを使用す
る準備ができました(The device is ready for use)" message is
displayed.
Installation of L-05A communication configuration file
(Driver) continues.
Setting up
37
■ For Windows XP
• On the lower right side of task tray, "新しいハードウェア
が見つかりました。(A new hardware has been found.)"
message is displayed, and the FOMA terminal is
recognized automatically.
• If the FOMA terminal is recognized properly, "新しいハー
ドウェアがインストールされ、使用準備ができました。(A new
hardware has been installed and ready for use.)"
message is displayed.
Setting Manually (CD)
■ For Windows Vista
After starting a PC Insert the included CDROM into the PC
"スタート(Start)" "すべてのプログラム(All
programs)" "アクセサリ(Accessory)" Click
"ファイル名を指定して実行(Specify a file name
and run)"
■ For Windows XP/2000
Click [スタート(Start)] 「ファイル名を指定して実行
(Specify a file)」
■ For Windows 2000
• The warning screen of removing device is displayed
which has nothing to do with using continually.
• "新しいハードウェアが見つかりました(A new hardware has
been found.)" message is displayed, and the FOMA
terminal is recognized automatically.
"自動再生" screen will be displayed depending on setting.If the
screen is displayed, check "ソフトウェアとゲームに対しては常に
次の動作を行う" and select "Launcher.exeの実行"
38
Setting up
Enter ":¥Windows¥
L-05A 接続ソフト¥StartCD.exe" in "名前
(Name)"
Click "OK"
Perform the same operations as those after
step 2 or later on "Setting Zero Installation
(Auto) (→ P36)"
Confirming the Installed L-05A Configuration File
(Drivers)
Confirmation after Installation
Confirming L-05A Connection Software
Double click L-05A connection software icon
When the following screen is displayed, the confirmation of
installation finishes.
Confirm whether L-05A Communication Configuration File
(Drivers) is set in a PC.
■ For Windows Vista
Click
"スタート(Start)" "コントロールパネル
(Control panel)" "システムとメンテナンス
(System and maintenance)" "デバイス マネー
ジャ(Device manager)" "続行(Continue)"
■ For Windows XP
Click "スタート(Start)" "コントロールパネル(Control
panel)" "パフォーマンスとメンテナンス(Performance
and maintenance)" "システム(System)" "デバイス マ
ネージャ(Device manager)" of "ハードウェア(Hardware)"
tab
■ For Windows 2000
Click "スタート(Start)" "設定(Settings)" "コントロール
パネル(Control panel)" "システム(System)" "デバイス マ
ネージャ(Device manager)" of "ハードウェア(Hardware)"
tab
Setting up
39
b
Click each device display to confirm the driver
name installed
• Confirm whether the driver name is displayed below "ポート
(COM とLPT)(Port (COM and LPT))", "モデム(Modem)"
• COM port number differs depending on user and PC.
Device name
40
Driver name
Port
(COM and LPT)
FOMA L05A USB Serial1 Device
FOMA L05A USB Serial2 Device
Modem
FOMA L05A
Setting up
Note
• If FOMA terminal is not recognized through the PC's
USB port, try other available USB port. FOMA terminal
may not be recognized properly with some USB port of
PC.
• When communicating data with L-05A connection
software, application operation of L-05A is required.
→P66
• When communicating data with DOCOMO connection
manager without L-05A connection software,
installation of DOCOMO connection manager is
required.→P79
• When communicating data with neither L-05A
connection software nor DOCOMO connection
manager, configure it manually.→P90
Uninstalling L-05A Connection Software
(including a driver)
If "キャンセル(Cancel)" is clicked, uninstallation will be
stopped.
■ For Windows XP/2000
• Before uninstalling, remove the FOMA terminal from the PC.
• Since "ユーザーアカウント制御 (User account control)"
screen is not displayed, follow the next procedure.
• When uninstalling, make sure to install from the account with
PC supervisor privileges.
• Make sure to save important data in FOMA card. Uninstallation
will results in data loss when Phonebook or SMS data is saved
in PC.
Click "許可(Allow)" on "ユーザーアカウント制御
(User account control)" screen
Click "アンインストール (Uninstall)"
Click [OK]
■ For Windows Vista
"スタート(Start)" "すべてのプログラム (All
programs)" "L-05A接続ソフト (L-05A
connection software)" Click "Uninstall"
■ For Windows XP
• "スタート (Start)" "すべてのプログラム (All programs)"
"L-05A 接続ソフト(L-05A connection software)" Click
"Uninstall"
■ For Windows 2000
• "スタート (Start)" "プログラム (Program)" "L-05A 接続ソ
フト(L-05A connection software)" Click "Uninstall"
Setting up
41
e
Click [OK]
Macintosh Version
When installing L-05A connection software, make sure to
finish "ドコモ コネクションマネージャ (DOCOMO connection
manager)" first.
Note
Click "完了 (Finish)"
• Do not remove the FOMA terminal while installing.
• When installing, make sure to install from the account with
PC supervisor privileges.
Preparation for Using L-05A
Setting Zero Installation (Auto)
Uninstallation finishes.
42
Setting up
Connect the FOMA terminal with a Mac
Double click the CD-ROM icon
CD-ROM icon is displayed on the desktop.
c
Double click "L-05A 接続ソフト インストーラー
.mpkg (L-05A connection software
installer.mpkg)"
Click "続ける (Continue)"
Click "続ける (Continue)"
Confirm "使用許諾契約 (The license
agreement)". If agree with the content, click
"同意する (I Agree)"
Setting up
43
g Click "インストール (Install)"
Click "インストールを続ける(Continue
installing)"
Enter administrator password Click "OK"
j Click "再起動(Restart)"
Mac restarts. Installation finishes.
44
Setting up
Setting Manually (CD)
Confirmation after Installation
Start Mac Insert the CD-ROM into Mac
CD-ROM icon on desktop appears.
Double click CD-ROM icon "Mac" "L-05A
connection software"
For subsequent steps, operate the same
procedures as those after procedure 3 in "Set
Zero Installation (Auto)" (→P43)
Confirming L-05A Connection Software
Double click L-05A connection software icon
When the following screen is displayed, the confirmation of
installation finishes.
Note
• When communicating data with L-05A connection software,
setting application operations of L-05A is required.→P66
• When communicating data with DOCOMO connection
manager without L-05A connection software, installation
of DOCOMO connection manager is required.→P79
Setting up
45
Uninstalling L-05A Connection Software
(including a driver)
Double click "L-05A接続ソフト (L-05A
connection software)"
Double click "アンインストーラ.app
(Uninstaller.app)"
• Before uninstalling, remove the FOMA terminal from the Mac.
• When uninstalling, make sure to install from the account with
PC supervisor privileges.
• Make sure to save important data in FOMA card. Uninstallation
will results in data loss when Phonebook or SMS data is saved
in PC.
• End "DOCOMO connection manager" when uninstalling L-05A
connection software.
46
Insert the included CD-ROM into a Mac
CD-ROM icon is displayed on the desktop.
Double click the CD-ROM icon
Double click "Mac"
Setting up
f
Click "アンインストール(Uninstall)"
g Enter administrator password
Click "OK"
Confirm whether the FOMA terminal is
connected to USB port before restarting
Click "再起動(Restart)"
Mac restarts. Uninstallation finishes.
Setting up
47
L-05A Connection Software
L-05A Connection Software ･････････････････････
Using Packet Communication ･･･････････････････
Using SMS ･･･････････････････････････････････････
Using Phonebook ････････････････････････････････
Using Application Option･････････････････････････
50
53
54
63
66
L-05A connection software is available to use on either Windows or Macintosh. Despite the display images of
Windows version and Macintosh version are a little different, icons on the screen and available functions are same.
Please note that in this chapter the descriptions are based on screen images of Windows.
49
L-05A Connection Software
The L-05A connection software allows you to use packet
communication/SMS/Phonebook.
• Using Packet Communication→P53
Allows you to easily use packet communication.
Launching and Exiting Connection
Software (For Windows)
Launching
• Double click
created on the desktop.
Exiting
• Click
located on the top of main application screen.
• Using SMS→P54
Features of composing messages, Inbox, Outbox, Drafts box
and Saving to FOMA card are available.
• Using Phonebook→P63
Features of composing messages, adding and deleting new
group, transferring group, adding new item, modifying user,
delection are available.
• Using Application Option→P66
Confirm the amount of packet communication data usage,
configure internet option, configure FOMA card, enter PIN1
code, configure the connection type (PDP), reset FOMA
terminal, configure network are available.
Note
• Data of L-05A connection software will be saved in PC if no
destination is specified.
50
L-05A Connection Software
Launching and Exiting Connection
Software (For Macintosh)
If connect with L-05A, it will be recognized as a CD-ROM
first. For recognizing as a modem, drug the CD-ROM icon
into trash.
Launching
• Launch "Finder" "アプリケーション(Application)"
ソフト.app (L-05A connection software.app)"
"L-05A 接続
Exiting
• Menu bar "L-05A 接続ソフト(L-05A connection software)"
"L-05A 接続ソフトを終了(Quit L-05A connection software)"
(Out of service area) In no signal reception area
Main Application Screen
Internet Connection
International Roaming
Unopened message found
a List of icon indicating FOMA terminal status
Signal reception level
Strong ←
※1 W-CDMA (3G)
A third generation mobile communication network complying
with 3GPP Global standards. 3Gpp means 3rd Generation
Partnership Project. The local standardization organization
established for the development of common technical
specifications related to 3rd Generation Mobile
Communication Systems (IMT-2000).
※2 HSDPA (Short for High Speed Downlink Packet Access)
HSUPA (Short for High Speed Uplink Packet Access)
A high speed type of W-CDMA data communication. It is called
"3.5G" since it is the improvement version of 3rd generation
(3G) cell phone (W-CDMA).
※3 GSM (Short for Global System for Mobile Communication)
The second generation mobile communication network in a
digital communication system that is most widely used around
the world.
※4 GPRS (Short for General Packet Radio Service)
GPRS is the 2.5 generation mobile communication system
that enables highspeed packet communication using GSM.
→ Weak
Network type
W-CDMA※1,
HSUPA※2,
HSDPA※2,
GSM※3/GPRS※4
L-05A Connection Software
51
b Status／Message display area
• FOMA terminal,warning messages, operation status,
network name.
f Current time/data display area
• Current date and time are displayed.
• Time is set conformable to PC time.
• The information of currently accessed network operator is
displayed when "network information" is set to "display"→P116
c Buttons for connecting and disconnecting to
Internet
• Click this button when connecting or disconnecting
Internet.
Confirming My Number
Click
from the main application screen, and then you
will see the following messages displayed.
d Data communication information display area
• During connecting to Internet, connection time and
amount of loaded data are displayed.
Version information
My number
e Operation button
• Buttons are available for SMS, Phonebook, Settings and
Information.
: SMS（P54）
: 電話帳 (Phonebook)（P63）
: 設定(Settings)（P66）
:インフォメーション(Information)
（P51）
52
L-05A Connection Software
Using Packet Communication
You can use packet communication if click
main application screen.
from the
Start Packet Communication
Click
from the main application screen
• Displays connection time, amount of downloaded data
connection status icon
Disconnecting to Packet Communication
Click
from the main application screen
• Packet communication will be disconnected after the
messages displayed "切断しています。(Connection is being
disconnected)".
Note
• The packet communication may be automatically
disconnected depending on the network status or location.
• In packet communication, fees apply on the amount of
sent/received data. Note that the communication fees may
become high if you perform heavy communications such as
by browsing websites which include large
multimediacontents or if you download a lot of data.
• Data communication fees under international roaming
differ from those in Japan.
L-05A Connection Software
53
When Receiving SMS
Using SMS
Allows you to use various SMS features if click
the main application screen.
from
The following screen appears when receiving SMS.
• Maximum number of SMS stored in PC is 1000. Depending on
PC's available hard disk space, number may differ. (Excluding
FOMA card SMS box)
Composing SMS
Click
Transferring to phonebook
Entering receiver's phone number
Message/receiversreset,
sending SMS
：Composing SMS
：Outbox
：Inbox
：Drafts box
：FOMA card SMS box
54
L-05A Connection Software
Composing SMS
Click
from the SMS application screen
Enter the SMS from the SMS composing
screen
• SMS can be entered up to 70 characters (English alphabet
& numeric characters can be entered up to 160
characters)
c
Enter the receiver's phone number
• Enter the receiver's phone number by clicking the input or
click
to display phonebook and decide a receiver.
• If you edit SMS or receiver, enter directly in SMS edit
screen or phone number field to modify.
Click
• SMS are being sent.
Note
• You will be prompted whether you want to save the SMS to
Drafts box or not, when moving to other applications or
when failure incurred in transmission. If you click
the SMS will be saved to Drafts box. If you click ,
the
SMS will not be saved to Drafts box.
• Setting "SMS一括拒否(Multi-refuse SMS)"
By using the following AT command, SMS is set in terminal
software.
For details of terminal software, refer to "通信の手動設定
(Configuring Network Manually)" P90
SMS refuse: AT+CUSD=1,"*141*1#",15
Unlock SMS refuse: AT+CUSD=1,"*141#",15
• Result of sending SMS.
L-05A Connection Software
55
Replying and Forwarding SMS from Inbox
Inbox
• Allows you to store SMS to Inbox.
Confirming SMS from Inbox
Click
Select and confirm the SMS from the SMS list
from the SMS application screen
Click
from SMS application screen
Select the reply/forward from Inbox list
Click
"返信(Reply)/転送(Forward)" menu is displayed
• Displays the list of received SMS.
• "返信(Reply)"：
• "転送(Forward)"： SMS to be sent are automatically
entered, and move to the SMS
composing screen. The receiver phone
number is required to enter.
: SMS opened
: SMS unopened
Receiver phone number
Browse phonebook application
screen → P64
Note
• The SMS status becomes opened once you click the
received SMS.
56
L-05A Connection Software
Receiver phone number is
automatically entered and move to the
SMS composing screen.
Click
Copying Inbox SMS to FOMA Card
Click
Outbox
from SMS application screen
• Allows you to store SMS in Outbox.
Select the SMS and right-click Click "FOMA
カードに保存(Save to FOMA card)"
• "FOMAカードに保存(Save to FOMA card)": Copy the
received SMS of PC to FOMA card.
Confirming SMS from Outbox
Click
Select and confirm the SMS from the list
from SMS application screen
• Displays the list of sent SMS.
• You can copy 20 SMS in total including sent and received
to your FOMA card.
Deleting SMS from Inbox
Click
：Sent SMS
from SMS application screen
Select the SMS to delete from the list of
Inbox Click
"削除(Delete)""全削除(Delete all)" menu displayed
• "削除(Delete)"：
Receiver's phone number
Browse phonebook application
screen → P64
Delete the selected SMS.
• "全削除(Delete all)"： Delete all SMS
The message for confirming is displayed.
Click
L-05A Connection Software
57
Editing SMS from Outbox
Click
from SMS application screen
Select the SMS to send from the list of
Outbox Click
Copying SMS from Inbox to FOMA Card
Click
from SMS application screen
Select the SMS and right click Click "FOMA
カードに保存(Save to FOMA card)"
• SMS composing screen
• "FOMAカードに保存(Save to FOMA card)"： Copy sent SMS
stored in a PC to FOMA card.
• Up to 20 received and sent SMS can be stored in FOMA
card.
• You will be prompted with SMS composing screen as soon
as the receiver phone number and SMS are entered.
• You can add or edit SMS and receiver phone number.
58
Click
L-05A Connection Software
Note
• The information of time will not be saved when SMS are
copied from Inbox to FOMA card.
Deleting SMS from Outbox
Click
Drafts Box
from SMS application screen
• Allows you store temporary SMS in Drafts box.
Select the SMS to delete from the list of
Inbox Click
"削除(Delete)""全削除(Delete all)" menu is displayed.
• "削除(Delete)"：
Delete the selected SMS.
• "全削除(Delete all)"：
Delete all SMS.
Confirming SMS from Drafts box
Click
Select and confirm the SMS from the list of
Drafts box
from SMS application screen
• The list of SMS from Drafts box will be displayed.
The message for confirming is displayed.
Click
L-05A Connection Software
59
Editing from Drafts Box
Click
Select the SMS to edit from the list of drafts
box Click
• You will be prompted with SMS composing screen as soon
as the receiver's phone number and SMS are entered.
• You can add or edit SMS and receiver's phone number.
FOMA Card SMS Box
from SMS application screen
Click
• Allows you to save SMS copied from Inbox or Outbox are to
FOMA card SMS box.
• Up to 20 received and sent SMS can be stored in FOMA card.
Confirming SMS from FOMA Card SMS Box
Click
Select and confirm the SMS from the FOMA
card SMS box
from SMS application screen
• The list of SMS from Drafts box will be displayed.
Deleting SMS from Drafts box
Click
from SMS application screen
Select the SMS to delete from the list of
drafts box Click
"削除(Delete)" and "全削除 (Delete all)" menu is displayed.
:Received SMS
(SMS unopened)
:Received SMS
(SMS opened)
:Sent SMS
• "削除(Delete)"：
Delete the selected SMS.
• "全削除(Delete all)"：
Delete all SMS.
The message for confirming is displayed.
60
Click
L-05A Connection Software
Replying and Forwarding SMS from FOMA Card
SMS Box
Click
from SMS application screen
Select the SMS to reply/forward from the list
of FOMA card SMS box Click
Deleting SMS from FOMA Card SMS box
Click
from SMS application screen
Select the SMS to delete from the list of
FOMA card SMS box Click
"削除(Delete)""全削除(Delete all)" menu is displayed.
"返信(Reply)""転送(Forward)" menu is displayed.
• "削除(Delete)"：
• "返信(Reply)"：
You will be prompted with SMS
composing screen as soon as the
receiptor's phone number and SMS are
entered.
• "転送(Forward)"： The SMS to be sent will be
automatically entered, and move to
SMS composing screen. The receiver's
phone number is required to enter.
Delete the selected SMS.
• "全削除(Delete all)"： Delete all SMS.
The message for confirming is displayed.
Click
Click
L-05A Connection Software
61
Saving SMS in FOMA Card SMS Box to PC
Click
Click "パソコンに保存(Save to PC)"
Click
from SMS application screen
Select the SMS to save from the list of FOMA
card SMS box Right click
Sending SMS from Phonebook
Select the phonebook record to send
Click
Click
from the phonebook application
• Receiver's phone number is automatically entered and
move to the SMS composing screen.
Click
Note
• Refert to "SMS作成する (Composing SMS)" to enter the
SMS.（P54）
62
L-05A Connection Software
Sending SMS from Japan to Overseas
■ SMS
• You can use the same mobile phone number overseas as is
used in Japan.
• If receiptor's terminal is FOMA terminal Enter "+", and
"country code", in front of receiptor's phone number, if
receiptor is subscribed to overseas carrier other than NTT
DOCOMO. Also, enter the "010" "Country code" "Receiptor's
mobile phone number" in order. (If receiptor's phone number
starts with "0", enter the phone number without "0"
• If the receiptor received unsupported characters of SMS
from the sender who subscribed to other overseas carrier,
the message may not be displayed properly.
Using Phonebook
Click
allows you to use various features of phonebook.
The list of stored phonebook records are displayed when
Phonebook records are stored in FOMA card.
• Total number of phonebook records to be stored may be
different depending on PC's available hard disk space. Total
number of phonebook records stored in FOMA card is maximum
50.
:Phonebook record
stored in FOMA card
:Phone number stored in PC
:Composing SMS
:Adding and deleting
new group
:Transferring group
:New record
:Editing record
:Delete
L-05A Connection Software
63
Adding Phonebook Record
• Follow the steps to add new phonebook record
Click
from the Phonebook application
Searching Phonebook Record
Enter the name to be searched
Click
Start the following operations
Select a group
Enter the name to be added
Enter the phonebook to be added
• You can enter Kanji, Hiragana, Katakana, English,
number, character. (Full-width 10 character. Half-width
21character). You can enter the 20 character length.
64
• You can search phonebook record by entering phone number.
Click
•
： Save entered information to phonebook.
•
： Not save entered information to phonebook.
Editing Phonebook Record
Select the phonebook record to be edited
Click
Click
Click
L-05A Connection Software
from the phonebook application
• Edit phonebook record number if editing screen appears.
•
： Save entered information to phonebook.
•
：
Click
Not save entered information to phonebook.
Deleting Phonebook Record
Select phonebook record to delete
Click
from the phonebook application
•
：
Delete phonebook record.
•
：
Cancel deleting phonebook record.
Adding New Group
Click
Click
from the phonebook application
Enter the group name to be added
• You can enter Kanji, Hiragana, Katakana, English,
number, character. (Full-width 20character , Half-width
20character).
Note
• If you have many phonebook record to delete, multi-select
phonebook records by using shift or Ctrl keys from key
board and then click delete button to delete the selected
phonebook record.
Click
L-05A Connection Software
65
Deleting Group Name
Click
from the phonebook application
Select the group name to be deleted
Using Application Option
Click
allows you to use various features of application
option by clicking from the main application screen.
Click
： Amount of downloaded data
Click
： Internet option
： FOMA card
Note
• "デフォルト(Default)" group and "FOMAカード (FOMA card)"
group can not be deleted.
： Connection configuration
： FOMA terminal reset
Phonebook Record Transfering Other Group
Select the phonebook record to be
transferred
Click
from the phonebook application
Select the group name to be transferred
Click
• Transfer the selected phonebook record to the group you
want to transfer to.
Note
• If selecting two or more record, select records by using Shift or
Ctrl keys and then click "起動(Transfer)" to collectively transfer.
66
L-05A Connection Software
： Network setup
The following s are required to connect Internet with L-05A
connection software.
a The setting of provider information
Register APN with other registration number () on
"接続方式設定(Connection type configuration)" screen.
(→P72)
b Basic setting
Configure "*99***#" as a dial number during packet
communication on "Basic setting (Internet Option)"
screen. Also configure "User name", "Passward" provided
by provider if required.
Based on the above preparations, the APN with
registration number entered in  will be connected to.
Confirming Packet Communication Volume
• Confirms that the amount of data transmission used in packet
communication
Click
Note
• The data usage displayed on the screen may differ from the
actual volume of packet communication.
from the application option screen.
Configuring Internet Option
全体使用量 (Total usage)
1ヶ月使用量 (Monthly usage)
• Allows you to configure basic settingsfor connecting to
Internet.
Click
from the application option screen
Start the following operations
ユーザー名 (ID)
前回の使用量 (Current usage)
パスワード (Password)
ダイヤル (Service number)
設定 (Configuration)
SMS センター番号
(SMS center number)
全体使用量(Total usage) Accumulated total data usage
：Initialize total usage to zero
設定 (Configuration)
1ヶ月使用量(Monthly usage) Monthly usage
：Initialize monthly usage to zero
基本設定リセット (Basic setting reset)
前回の使用量 data usage of current session
L-05A Connection Software
67

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
XMP Toolkit                     : 3.1-702
Modify Date                     : 2009:04:23 14:01:17-04:00
Create Date                     : 2009:04:23 14:00:48-04:00
Metadata Date                   : 2009:04:23 14:01:17-04:00
Creator Tool                    : FrameMaker 7.0
Format                          : application/pdf
Title                           : L05A_Manual_E.book
Creator                         : Administrator
Document ID                     : uuid:185728dc-5f26-4a37-ad47-27bd41f62cd0
Instance ID                     : uuid:8ed31c0d-4f7f-41b8-a750-f366183a837e
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Has XFA                         : No
Page Count                      : 70
Author                          : Administrator

EXIF Metadata provided by EXIF.tools