LG Electronics USA L05A 850/ 1900 GSM/ GPRS/ EDGE and 850 WCDMA USB Dongle User Manual L05A Manual E

Download:
Mirror Download [FCC.gov]
Document ID	1100757
Application ID	ydy7G9XWFO5rjOYNM3swTg==
Document Description	Users Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	314.51kB (3931381 bits)
Date Submitted	2009-04-23 00:00:00
Date Available	2009-07-20 00:00:00
Creation Date	2009-04-23 14:01:49
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2009-04-23 14:02:04
Document Title	L05A_Manual_E.book
Document Creator	FrameMaker 7.0
Document Author:	Administrator

ユーザー名(ID) ID supplied from service provider
パスワード(Password) The password supplied from
service provider
ダイヤル(Service number) number of service provider
※For packet communication, enter *99***. Enter the
registration number of APN set in (P72).
SMSセンター番号(SMS center number)
※Normally, change in setting is not necessary. Enter SMS
center number when using SMS from the network
operator other than DOCOMO.
設定(Configuration) Click to change setting
基本設定リセット(Basic setting reset)
Click to return to basic setting
Click the applicable
Note
• Click
"設定(Configuration)" to renew the setting.
Always remember to click when setting is changed.
• You will not connect to Internet if ID, password and service
number are incorrect.
• SMS may not be sent or received when SMS service
number has been improperly entered.
• In Macintosh, input any character in user name and
passward.
68
L-05A Connection Software
Configuring FOMA Card
• Allows you to configure "PIN1ロック(PIN1 lock)", "PIN1解除
(PIN1 unblocking)", "PIN1暗証番号変更 (PIN1code change)"
Click
from the application option
PIN1 モード (PIN1 Mode)
PIN1
Locking PIN1
• Set security to FOMA card.
Select "PIN1ロック(PIN1 locking)" from PIN1
mode
Enter the PIN1 code configured in FOMA card
to "PIN1"
Click
Unblocking PIN1
Select "PIN1解除(Unblocking PIN1)" from PIN
mode
Enter the PIN1 code configured in FOMA card
to "PIN1"
Click
Click
Click
Note
Note
• When starting L-05A connection software with PIN1
locked, you need to enter PIN1 code from the screen of
entering PIN1 code.You can not use FOMA terminal
properly unless you enter correct PIN1 code.
• If PIN1 unblocking code is set, you can use FOMA card
information from FOMA terminal without verifying PIN1
code.
L-05A Connection Software
69
Modifying PIN1 Code
Enter the PIN1 code entered in "新しいPIN1
コード (New PIN1code)" code in "再入力
(Confirming New PIN 1code)"again to verify
Click
• Set the password required when unlocking or locking PIN1.
• Changing PIN1 code is only available when PIN is locked.
Select "PIN1暗証番号変更(Changing password
of PIN1)" from PIN1 mode
PIN1 モード (PIN1 Mode)
PIN1 コード (PIN1 Code)
現在の PIN1 コード
(Current PIN1 Code)
変更する PIN1 コード
(PIN1 Code to change)
変更する PIN1 コード確認
(Confirming PIN1 Code to change)
70
Enter the FOMA card PIN1 code to "PIN1"
Enter the PIN1 code change in "新しいPIN1
コード(New PIN1 code)"
L-05A Connection Software
Click
Entering PIN1 Code
• When L-05A connection software is started after setting PIN1
Lock, PIN1 code input screen will appear or it is restart to
reset FOMA terminal.
Ex.3： When PIN1 code has been improperly entered 3
times in a row.
• If you improperly enter the PIN1 code 3 times in a row,
the verification screen for unblocking PIN1 code will be
displayed.
Enter PIN1code
Enter the 4 to 8 PIN1 code
■ Unblocking locked PIN1 code
Verify the result after entering PIN1 code
Ex.1： When PIN1 code has been successfully entered.
a Enter the unblocking PIN1 code to "PIN1ロック解除コード
(Unblock)"
b Enter the PIN1 code to "新しいPIN1コード(New PIN1
code)" to change
c Enter the PIN1 entered in "新しいPIN1コード(New PIN1
code)" in "再入力(confirming New PIN1 code)" to confirm
d Click
Ex.2： When PIN1 code has been improperly entered.
L-05A Connection Software
71
Caution
• Be careful not to lose FOMA card. DOCOMO is not
responsible for the lost or stolen device.
• Do not transfer FOMA card to others.
• Treat it carefully as the data stored in FOMA card can be
easily damaged from scratching or bending.
• When connecting FOMA terminal to a PC for the first time,
you are required to enter PIN1 code to use FOMA card.
• If an incorrect PIN1 code is entered 3 times in a row, the
service will be suspended. To use it again, you must enter
unblocking PIN1 code.
• If an incorrect unblocking PIN1 code is entered 10 times in
a row, FOMA card locks automatically, so be sure to keep a
separate note of the number. Contact a DOCOMO shop if
you are not able to unblock the locked PIN 1.
Configuring Connection type (PDP Type)
• Configure connection type.
Click
from Internet Option screen
Start the following operations
a 登録番号 (Registration number (cid))
b 接続方式 (Connection type)
c 接続先 (Access Point Name (APN))
d 接続方式登録
(Connection type registration)
e 接続方式設定リセット
(Connection type setting reset)
a 登録番号(Registration Number(cid))
The registration numbers are available from cid1 to cid 10
in FOMA terminal. To connect to a provider other than
「mopera U」or 「mopera」, you can set the access point
name (APN) to any of cid2 or cid4 to cid10.
b 接続方式(Connection type)
PDP type IP and PDP type PPP are available for Internet
connection type. You can select the Internet connection
type you want to use or check the currently configured
internet connection type.
72
L-05A Connection Software
c 接続先(Access Point Name (APN))
Configure APN for packet communication. You can
configure APN of provider you want to use or check the
currently configured APN.
（Connection type registration）
Save the modified information to FOMA terminal.
（Connection type setting reset）
Reset all PDP configurations.
Select the Internet connection type
supporting Access Point.
Enter APN
Saving and Editing the Provider Information
• Save or edit the provider information you want to use.
Select cid Select the registration number to
save/edit
■ cid
The registration numbers are available from cid1 to
cid 10 in FOMA terminal.
• To connect to a provider other than「mopera U」or
「mopera」, you can set the access point name (APN)
to any of cid2 or cid4 to cid10.
Registration
number（cid）
Access Point name（APN）
mopera.ne.jp「mopera」
Unassigned
mopera.net「mopera U」
4∼10
Unassigned
• When "cid=3"selected "PDP type IP" Configure mopera.net
This service provides a maximum data speed of 7.2Mbps
for receiving and 5.7Mbps for sending.
• When "cid=1" selected "PDP type PPP" onfigure
mopera.ne.jp This service provides a maximum data speed
of 384kbps for receiving and 384kbps for sending.
L-05A Connection Software
73
Note
■ Configuring sender ID
You can configure to display sender ID or not by
adding 186/184 before APN.
• Add "186." before APN if you want to display sender ID.
• Add "184." before APN if you don't want to display sender.
Registration
APN
Display sender ID
186.mopera.net
Not display Sender ID
184.mopera.net
Click
Resetting FOMA Terminal
• Allows you to reset FOMA terminal.
Click
from the application option
FOMA 端末リセット
(FOMA terminal reset)
Click
Retrieving Provider Information
aIf select the cid of the "登録番号(Registration
Number(cid))" b"接続方式(connection type)" and c"接続先
(Access Point Name (APN))"will be displayed.
■ FOMA端末リセット(FOMA terminal reset)
Reset FOMA terminal for the following cases
• When FOMA terminal is operating improperly.
• When FOMA card is reinserted while inserting the FOMA
terminal to a PC.
74
L-05A Connection Software
b
Click
• FOMA terminal is restarting.
L-05A Connection Software
75
DOCOMO Connection Manager
DOCOMO Connection Manager ････････････････
Windows Version ･･････････････････････････････
Macintosh Version ･････････････････････････････
78
79
83
77
DOCOMO Connection Manager
DOCOMO connection manager is a software packets the
necessary connection software to operate "定額データプラ
ン接続ソフト (Flat-rate data plan connection software)" and
measured data communication which are necessary when
using flat-rate data plan.
「DOCOMO connection manager」is a software to connect
data communication terminal by data communication
correponding terminal. Subscribing 「mopera U」or
configuring a PC operates easily.
Also, confirming amount of data communication and
charges through charge counter feature is available.
This manual introduces the installation method of
DOCOMO connection manager.
For connecting the terminal with Internet, agreement with
the Internet service provider 「
( mopera U」etc.) supporting
service and data communication is required.
View DOCOMO web site for detailed information (Japanese
only).
Note
■ Using a flat-rate data plan
• For using a flat-rate data plan, the agreement with the
charge plan corresponding to the flat-rate data
communication and internet service provider is required.
View DOCOMO web site for further information.
■ Using measured-rate data communication
Charge counter
• Note that the communication fees may come high if you
perform heavy packet communications such as viewing
home page with pictures inside, downloading data (Ex.：
Application/Music/Data/OS/anti-virus software update)
etc.
Note that when performing data communication after
connecting this FOMA terminal with a PC by a USB cable,
「パケ･ホーダイ (Pake-hodai) 」
、
「パケ･ホーダイフル (Pakehodaifull)」
、
「Biz･ホーダイ (Biz-hodai)」and「Biz･ホーダイ ダ
ブル (Biz-hodai double)」are not included in the FOMA
packet Flat-rate service.
■ Using mopera
Windows version
Macintosh version
Connect/disconnect
78
DOCOMO Connection Manager
• For connection configuration, view mopera web site.
http://www.mopera.net/mopera/support/index.html
(Japanese only)
Note
Windows Version
Before Installing DOCOMO Connection
Manager
■ Setting Internet Explorer
Before installing this software, set connection setting to
"ダイヤルしない (Do not dial)" in Internet Option of Internet
Explorer.
■ Use other connection software besides DOCOMO
connection manager
This software has equate features with the following
software. Therefore, it is not necessary to use the following
software at the same time.
※ If required, change the setting to not start or uninstall.
- mopera U start up tools
- mopera U connection & setting tool
- FOMA PC configuration software
- FOMA byte counter
Also, when using Mzone (Public Wireless LAN Connection)
in this software, uninstall the following public wireless LAN
connection software.
※ When the following software are installed at the same
time, the Mzone connection of this software is not
available.
- U Public Wireless LAN Utility Software
- DOCOMO Public Wireless LAN Utility Software
- DOCOMO Public Wireless LAN Utility Program
a Start Internet Explorer Select "ツール (Tool)"−"インター
ネットオプション (Internet Option)"
b Select "接続 (Connection)" tab Select "ダイヤルしない (Do
not dial)"
c Click "OK"
DOCOMO Connection Manager
79
a
Log on by DOCOMO connection manager user
■ For Windows Vista
An administrator is required. When logged on by other
people than the administrator, entering user name
and password will be asked.
■ For Windows XP/2000
The user belongs to administrators group or the user
of "コンピュータの管理者 (Administrator of computer)"
operates log-on.
Installing DOCOMO Connection Manager
Launch the installer of DOCOMO connection
manager using the included CD-ROM
Select "付属CD-ROM (the included CD-ROM)"
"Windows"
"dcm_connect_manager" "dcm_connect_full_setup.exe"
Note
• When Windows XP does not contain MSXML6 and
Wireless LAN API, installation is required before installing
DOCOMO connection manager. Press "Install" when the
confirmation screen is displayed.
• After finishing installing MSXML6 and Wireless LAN API,
if reboot Windows, the installation of DOCOMO
connection manager starts automatically.
Exiting all the applications launched
Besides anti-virus software, programs resident in Windows
are also finished.
• Ex: Right click the icon shown on task bar, and select "閉じ
る (Close)" or "終了 (Finish)".
80
DOCOMO Connection Manager
Click "続行 (Continue)"
For Windows XP/2000, "ユーザーアカウント制御 (User
account control)" screen is not displayed. Setup program
starts right away.
c
Click "次へ (Next)"
Make sure to confirm the caution and then
click "次へ (Next)"
Confirm the content of the license agreement.
When agree with the content, select "使用許諾
契約の全条項に同意します (I agree with the
license agreement stipulations)" and click "次
へ (Next)"
Confirm the destination folder and click "次へ
(Next)"
DOCOMO Connection Manager
81
g Click "インストール (Install)"
Installing starts.
Launching DOCOMO Connection Manager
"スタート (Start)" "すべてのプログラム(All
programs)" "NTT DOCOMO" "ドコモ コネク
ションマネージャ (DOCOMO connection
manager)" "ドコモ コネクションマネージャ
(DOCOMO connection manager)"
DOCOMO connection manager starts.
82
Click "完了 (Finish)"
Installing finishes.
DOCOMO Connection Manager
For the first launching, the wizard setting is
displayed automatically.
The connection with Internet gets prepared when operating
or setting following the instruction of software.
Refer to 『ドコモ コネクションマネージャ操作マニュアル
(DOCOMO connection manager operation manual).pdf』for
detailed information.
Note
Macintosh Version
• Just exiting the Internet browser or mail software does
not disconnect the connection.
When do not use communication, make sure to press "切
断する (Disconnect)" button to disconnect the
connection.
For OS update, if auto update is set, the software will be
updated automatically. Note that the packet
communication fee may come high.
Installing DOCOMO Connection Manager
Note
• Use Ver. 1.00.0003 or later for "DOCOMO connection
manager for Mac".
Disconnect
Launch the installer of DOCOMO connection
manager from the included CD-ROM
• Select "付属CD-ROM (included CD-ROM)"
"Mac"
"dcm_connect_manager"
"dcm_for_Mac"
"インストール
(Install)" Select "ドコモ コネクションマネージャをインストー
ルします (Install DOCOMO connection manager)" and click
"OK"
DOCOMO Connection Manager
83
84
Click "続ける (Continue)"
Make sure to confirm "大切な情報 (Important
information)", and click "続ける (Continue)"
DOCOMO Connection Manager
Click "続ける (Continue)"
e
Confirm "使用許諾契約 (The license
agreement)", when agree with the content,
click "同意する (I Agree)" Click "続行
(Continue)"
Confirming the destination folder to install
and click "インストール (Install)"
administrator name and
g Enter
password Click "OK"
The user account created after Mac OS X is set becomes
the administrator of PC. Enter the used name and password.
DOCOMO Connection Manager
85
h
86
Click "インストールを続ける (Continue
installing)"
Click "ログアウト (Log out)"
Installing finishes.
DOCOMO Connection Manager
Note
• If click "ログアウト (Log out)", setting assistant screen is
displayed.
The connection with Internet gets prepared when
operating or setting following the instruction of
software.
Refer to 『ドコモ コネクションマネージャ操作マニュアル
(DOCOMO connection manager operation manual)』for
detailed information.
Note
Launching DOCOMO Connection
Manager
"アプリケーション (Application)" "ドコモ コネク
ションマネージャ (DOCOMO connection
manager)" "ドコモ コネクションマネージャ
(DOCOMO connection manager)"
• Just exiting the Internet browser or mail software does
not disconnect the connection.
When do not use communication, make sure to press "切
断する (Disconnect)" button to disconnect the
connection.
For OS update, if auto update is set, the software will be
updated automatically. Note that the packet
communication fee may come high.
• DOCOMO connection manager starts.
For the first launching, the wizard setting is
displayed automatically
The connection with Internet gets prepared when operating
or setting following the instruction of software.
Refer to 『ドコモ コネクションマネージャ操作マニュアル
(DOCOMO connection manager operation manual.pdf)』for
detailed information.
Disconnect
DOCOMO Connection Manager
87
Configuring Network Manually
Configuring a Dial-up Network Manually ･････････ 90
Communicating (Connecting by Dial-up) ･････････ 109
89
For Windows XP
Configuring a Dial-up Network
Manually
Connect the FOMA terminal with a PC
This section describes the steps to configure settings for
packet communication without using L-05A connection
software or DOCOMO connection manager.
Click "スタート(Start)" "すべてのプログラ ム
(All programs)" "アクセサリ (Accessories)"
"通信(Communication)"
"ハイパーターミナル
(Hyper Terminal)"
Setting APN
Set the access point (APN) in packet communication. Up
to 10 APN can be set up and they are managed with cid's.
Communication software is required to enter AT
commands. This section describes the steps necessary for
using the "ハイパーターミナル(Hyper Terminal)" that comes
with Windows.
• The registration number (cid) 1 is set to mopera.ne.jp and the
registration number 3 is set to mopera.net by default. Use cid
2 or from 4 to 10 when setting another access point.
• "ハイパーターミナル(Hyper Terminal)" does not come with
Windows Vista. To configure the settings in Windows Vista,
use communication software compatible with Windows Vista.
For the setting procedures, refer to the instruction manual and
other documentation that came with the software to be used.
•
90
For a connection (APN) other than 「mopera U」 or 「mopera」
, contact your ISP or network administrator.
Configuring Network Manually
• Connecting method→P24
Hyper Terminal starts.
■ For Windows 2000
Click "スタート(Start)"
"プログラム (Programs)"
クセサリ(Accessories)"
"通信(Communication)"
イパーターミナ ル(Hyper Terminal)".
"ア
"ハ
Enter a connection name in the "名前 (Name)"
field
Click "OK"
d
Enter a non-existing phone number (such as
"0") in the "電話番号(Phone Number)" field
Check that "FOMA L05A" is displayed for "接
続方法(Connection Method)"
Click "OK"
• If more than one modem name are displayed in the "接続方
法(Connection Method)" field, check the FOMA terminal
modem name and select the proper one.→P40
Enter the APN in the following
format Press
Enter AT+CGDCONT=,"",""
Enter the following information in the corresponding ,
 and  sections.
If "OK" appears after you enter the information, the APN has
been setup.
cid
： Enter any number from 2, and from 4 to 10.
※ Keep in mind that the old setting
information will be overwritten if you select
a cid number which has already been set.
PDP type ： Select either PPP or IP for the connection
method supported by the access point, and
then enter the information enclosed in
quotation marks ("").
APN
： Enter the connection (APN) enclose it in
quotation marks " ".
• If the entered characters do not appear, enter ATE1.
Click "キャンセル(Cancel)" on the connection
screen
The Hyper Termina screen opens.
If register an access point with PPP in the PDP type and
XXX.com in the APN of cid2
■ To reset the specified APN settings
Enter AT+CGDCONT=
■ To view the registered APN
Enter AT+CGDCONT
Configuring Network Manually
91
g Check if "OK" is displayed
Configuring Dial-up Network
Set up the dial-up network on the PC.
• For setting up a connection to other than 「mopera U」or
「mopera」, contact your ISP or network administrator.
Example: Connecting to the DOCOMO Internet connection
service 「mopera U」, which is registered to =3
Click "ファイル(File)" "ハイパーターミナル の終
了(Exit Hyper Terminal)"
Click "はい(Yes)" on the confirming
disconnection screen Click "いいえ(No)" on
the confirming to save screen
Hyper Terminal will quit, and the setting of the APN
completes.
Note
• The APN information is saved in the FOMA terminal. If you
connect a different FOMA terminal, save the APN
information again.
• If you want to use the APN information registered on the
PC, register the same APN in the same cid of the FOMA
terminal.
92
Configuring Network Manually
For Windows Vista
Click
"スタート(Start)"
(Connection)"
Click "接続またはネットワークをセットアップしま
す(Set up connection or network)"
"接続先
c
Select "ダイヤルアップ接続をセットアップします
(Set up dial-up connection)"
Click "次へ
(Next)"
When the modem selection screen appears,
click "FOMA L05A"
The modem selection screen opens only when the PC has
more than one modem.
Configuring Network Manually
93
e
Configure various settings, then click "接続
(Connect)"
• Enter the APN number in the "ダイヤルアップの電話番号
(Phone number to a dial-up connection)".
• Enter the user name and password specified by your ISP or
network administrator in the "ユーザー名(User name)" and "
パスワード(Password)" fields.
• You can leave the user name and password fields unfilled
when connecting to 「mopera U」/「mopera」.
• Enter a connection name in the "接続名 (Connection Name)"
field.
94
Configuring Network Manually
Click "スキップ(Skip)" on the "(接続名)に接続中...
(Connecting to (APN))" screen
The connection test will not be performed. Only the settings
will be checked.
• If you do not click "スキップ(Skip)", the connection to the
Internet will be established.
"接続をセットアップします(Set up the
g Click
connection)"
"閉じる(Close)"
the settings on the "全般(General)" tab
j Check
window
If two or more modems are connected to a PC, enable only "
モデム - FOMA L05A (Modem - FOMA L05A)" in the "接続方法
(Connection Method)" field.
• Disable "ダイヤル情報を使う(Use dialing information)".
Click
"スタート(Start)"
(Connection)"
Select the created dial-up connection icon
Right click "プロパティ (Properties)"
"接続先
Configuring Network Manually
95
"ネットワーク(Networking)" tab
k Click
Configure each setting
Place a checkmark next to the "インターネッ トプロトコルバー
ジョン4 (TCP/IPv4) (Internet Protocol 4 (TCP/IPv4))"
checkbox in the "この接続は次の項目を使用します(This
connection uses the following items)" field. Obtain the
settings for "QoSパケットスケジューラ(QoS Packet
Scheduler)" from your ISP or network administrator.
• To set up TCP/IP, click "プロパティ (Properties)". Contact
your ISP or network administrator for setting up.
the "オプション(Option)" tab
l Click
"PPP設定(PPP Settings)"
Remove checkmarks from all items
m "OK"
Click
Click
the "オプション(Option)" tab window, click
n On
"OK"
96
Configuring Network Manually
For Windows XP
Click "スタート(Start)"
"すべてのプログラム
(All programs)"
"アクセサリ (Accessories)"
"通信(Communication)" "新しい接続ウィザー
ド(New Connection Wizard)"
On the New connection wizard screen, click "
次へ(Next)"
Select "インターネットに接続する(Connect to
the Internet)"
Click "次へ(Next)"
Select "接続を手動でセットアップする(Set up
the connection manually)"
Click "次へ
(Next)"
Configuring Network Manually
97
e
Select "ダイヤルアップモデムを使用して接続する
(Use a dial-up modem to connect)"
Click "次
へ(Next)"
If "デバイスの選択(Select a device)" screen
appears, check in "モデム - FOMA L05A
(COM4) (Modem - FOMA L05A(COM4))"
checkbox
Click "次へ(Next)"
Enter a name in the "ISP名(ISP Name)"field
g Click
"次へ(Next)"
Enter the APN phone number in the "電話番号
(Phone Number)" field
Click " 次へ (Next)"
The "デバイスの選択(Select a device)" screen appears only
when the PC has more than one modem.
■ For packet communication
Enter "*99***#". Enter the registered number of
APN in . (P73)
98
Configuring Network Manually
i
Select the connection usage range
次へ(Next)"
Click "
k Click "完了(Finish)"
The new connection wizard appears.
Select a user.
• Depending on the PC settings, this screen may not
appear.
in the "ユーザー名(User Name)", "パスワード
j Fill
(Password)", and "パスワードの確認入力
(Confirm password)" fields
(Next)"
Click "次へ
Enter the information provided by your ISP or network
administrator.
• Enter "ユーザ名(User name)" and "パスワード (Password)"
correctly according to the instruction from the provider.
Pay attention to the capital characters.
• To connect to 「mopera U」or 「mopera」, these fields can
be left unfilled.
"スタート(Start)"
"すべてのプログラム
l Click
(All programs)" "アクセサリ(Accessories)"
"通信(Communication)"
(Network Connection)"
"ネットワーク接続
Configuring Network Manually
99
Select the created dial-up connection icon
m Right
click Click "プロパティ(Properties)"
the settings on the "全般(General)" tab
n Check
window
• If more than one modem is connected to a PC, enable only
"モデム - FOMA L05A (COM4) (Modem - FOMA L05A
(COM4))" in the "接続方法 (Connection Method)" field.
• Disable "ダイヤル情報を使う(Use dialing information)".
100
Configuring Network Manually
the "ネットワーク(Networking)"
o Click
tab Confirm each item Click "設定
Remove checkmarks from all items
q "OK"
Click
(Settings)"
• Select "PPP:Windows 95/98/NT4/2000, Internet" in the "
呼び出すダイヤルアップ サーバ ーの種類(Dial-up server type to
call)" field
• Enable "インターネットプロトコル(Internet Protocol) (TCP/
IP)" in the "この接続は次の項目を使用します(This connection
uses the following items)" field. You cannot change the
settings of "Qosパケットスケジューラ (QoS Packet
Scheduler)". Use it as usual.
"OK" on the "ネットワーク(Networking)"
r click
tab window
• When connecting to provider, to confirm the TCP/IP
setting contact the provider or network administrator.
For Windows 2000
Click "スタート(Start)"
"プログラム
(Programs)"
"アクセサリ(Accessories)"
通信(Communication)"
"ネットワークとダイヤ
ルアップ接続(Network and Dialup
Connections)"
On the Network and Dial-up connection
screen, double-click the"新しい接続の作成
(Create new connection)" icon
p Click "設定(Settings)"
Configuring Network Manually
101
c
If the location information screen appears,
enter "市外局番(City code)"
Click "OK"
This appears only when "新しい接続の作成 (Create new
connection)" is launched for the first time. Go to Step 5 when
launching this for the second time or later.
102
On the phone and modem option screen, click
"OK"
On the Network connection wizard screen,
click "次へ(Next)"
Configuring Network Manually
Select "インターネットにダイヤルアップ接続する
(Connect to Internet via dial-up)" Click "次へ
(Next)"
"インターネット接続を手動で設定するか、ま
g Select
たはローカルエリアネットワーク(LAN)を使って接
続します(Set up the Internet connection
manually, or connect to the Internet using
LAN)"
Click "次へ(Next)"
Select "電話回線とモデムを使ってインターネット
に接続します(Connect to the Internet using a
telephone line and a modem)"
Click "次へ
(Next)"
Configuring Network Manually
103
i
If the modem selection screen opens, select
"FOMA L05A"
Click "次へ (Next)"
The modem selection screen opens only when the PC has
more than one modem.
• If "FOMA L05A" is not displayed, click "インターネットへの接
続に使うモデムを選択する (Select the modem used to
connect to the Internet)" field and then select "FOMA
L05A".
the APN phone number in the "電話番号
j Enter
(Phone Number)" field
Click "詳細設定
(Advanced settings)"
• Do not enter anything in "市外局番(City code)" field
• Disable "市外局番とダイヤル情報を使う(Use the city code and
dialing information)".
■ Packet communication information
Enter "*99***#". Enter registration number of
APN in .
104
Configuring Network Manually
the settings on the "接続
k Configure
(Connection)" tab window according to the
examples on the screen.
• If you are connecting to other than「mopera U」or
「mopera」, fill in the "接続の種類 (Connection type)" and " ロ
グオンの手続き (Log on procedures)" fields according to the
information provided by your ISP or network administrator.
Click the "アドレス(Address)" tab
l item
Click "OK"
Set each
• If you are connecting to other than 「mopera U」or
「mopera」, fill in the "IPアドレス (IP address)" and "ISPによ
るDNS (ドメインネームサービス) アドレスの自動割り当て
(Assign DNS address automatically by ISP)" fields
according to the information provided by your ISP, and
follow the instruction from provider.
the "インターネットアカウントの接続情報
m On
(Internet account connection information)"
screen, click "次へ(Next)"
Configuring Network Manually
105
"ユーザー名(User Name)" and "パスワード
n Enter
(Password)"
Click "次へ(Next)"
• Enter "ユーザ名(User name)」and "パスワード(Password)"
correctly according to the instruction from the provider.
Pay attention to the capital characters.
106
Configuring Network Manually
Note
• For 「mopera U」or 「mopera」, connection is operated
even when "ユーザ名(User name)" field and "パスワード
(Password)" field are empty. The screen "ユーザ名を空白の
ままにしておきますか？ (Is it OK to enter nothing in User
name?)" is displayed in this case. Click "はい(OK)" in each
screen.
a connection name in the "接続名
o Enter
q Click "完了(Finish)"
(Connection Name)" field Click "次へ (Next)"
• If "今すぐインターネットに接続するにはここを選び完了をクリッ
クしてください(Select this to connect to the Internet now
and click Finish)" appears, disable the option.
p Select "いいえ(No)"
Click "次へ(Next)"
• When setting Internet mail, select "はい(OK)". Contact the
provider for detailed information of setting.
the created dial-up connection icon
r Select
Click "ファイル(File)"
"プロパティ
(Properties)"
Configuring Network Manually
107
the settings on the "全般(General)" tab
the "ネットワーク(Networking)"
s Check
t Click
window
tab Confirm each item Click "設定
• If more than one modem is connected to a PC, enable only
"モデム - FOMA L05A (COM3) (Modem - FOMA L05A
(COM3))" in the "接続の方法 (Connection Method)" field
• Disable "ダイヤル情報を使う(Use dialing information)".
(Settings)"
• Select "PPP:Windows 95/98/NT4/2000, Internet" in the "
呼び出すダイヤルアップサーバーの種類(Dial-up server type to
call)" field.
• Enable only "インターネットプロトコル (Internet protocol)
(TCP/IP)" in the "コンポーネント(Components)" field.
u Click "設定(Settings)"
v Remove checkmarks from all items
Click "OK"
"OK" on the "ネットワーク(Networking)"
w Click
tab window
108
Configuring Network Manually
b
Communicating (Connecting by
Dial-up)
イヤルアップ接続する
This section describes steps to start and terminate
communication without using L-05A connection software
or DOCOMO connection manager.
• Check whether the FOMA terminal and the PC are connected
properly before starting communication.→P24
• When performing communication, connect the FOMA terminal
you used to configure the settings. If a different FOMA terminal
is connected, L-05A Communication Configuration Files
(Drivers) may need to be reinstalled.
For Windows Vista
Enter "ユーザー名(User Name)" and "パスワード
(Password)"
Click "ダイヤル(Dial)"
The APN will be connected.
• To connect to 「mopera U」or 「mopera」, you can leave
the " ユーザー名(User Name)" and "パスワード(Password)"
fields unfilled and click "ダイヤル(Dial)". If another ISP or
dialup connection is selected, fill in the "ユーザー名(User
Name)" and "パスワード (Password)" fields and click "ダイヤ
ル (Dial)".
• You can save the user name and password or just the
password to skip entering them next time.
• Depending on the operating system, a connection
completion screen may appear when the dial-up
connection is established. However, the connection
completion screen does not appear if you previously set
the completion message not to appear.
Click
"スタート(Start)" "接続先 (Connect
to)" Select the access point that has been
set up Click "接続 (Connect)."
■ For Windows XP
Click " スタート(Start)"
"すべてのプログラム(All
programs)" "アクセサリ (Accessories)"
"通信
(Communication)"
"ネットワーク接続(Network
connection)"
Double click the APN that has been
set up
■ For Windows 2000
Click "スタート(Start)"
"プログラム (Programs)"
"ア
クセサリ(Accessories)"
"通信(Communication)"
ネットワークとダイヤルアップ接続(Network and Dialup
Connections)"
Double-click the APN icon that has
been set up.
Configuring Network Manually
109
Disconnecting Communication
Click "切断(Disconnect)"
The communication will be terminated.
Exiting the Internet browser may not terminate the
connection. Perform the following steps to terminate the
connection securely.
For Windows Vista
Click
the PC
the dial-up icon in the task tray of
A screen indicating the connection status appears.
Click "接続または切断(Connect or disconnect)"
Note
■ For Window XP/2000
The above screen will not be displayed. Follow the
next procedure.
110
Configuring Network Manually
• The communication speed shown on the PC screen may
be different from the actual communication speed.
Overseas Use
International Roaming Service (WORLD WING) ･･
Services Available Overseas ････････････････････
Before Using Overseas ･･････････････････････････
Setting the Searching Method for Available
Networks ･･････････････････････････････････････
Configuring Network･･･････････････････････････
112
112
113
115
116
111
International Roaming Service
(WORLD WING)
WORLD WING is DOCOMO's international roaming service
that provides telephone and other types of communication
services overseas out of the service area of FOMA
network, using affiliated overseas network.
Services Available Overseas
Available communication services may vary depending on
the overseas carrier or network.
Available Communication Services
• The following 3 types of communication are included in
overseas network.
■3G network
A third generation mobile communication network
complying with 3GPP Global standards. (3rd Generation
Partnership Project)※
※ The local satandardization organization established for
the development of common technical specifications
related to 3rd Generation Mobile Communication Systems
(IMT-2000)
■GSM (Global System for Mobile Communication) network
The second generation mobile communication network in
a digital communication system that is most widely used
around the world.
■GPRS (3General Packet Radio Service) network
GPRS is the 2.5 generation mobile communication
system that enables high speed packet communication
using GSM.
• It is available to use 3G network or GSM/GPRS network service
within service area. For countries/areas support 3G850MHz/
GSM850MHz, it is also available to use.
• Before using the FOMA terminal overseas, refer to the
followings.
- "Mobile Phone User's Guide [International Services]"
- DOCOMO "International Service Web site"
112
Overseas Use
Service
Data
Communication
Description
Available for data communication using
packets communication.
※ Sending and receiving SMS may be available in overseas.
Please understand that communication fee is counted
when sending SMS.
※ Packet communication is not available for GSM network
communication type.
Note
• For details on available communication services while
using international roaming, refer to Mobile Phone User's
Guide [International Services] or visit DOCOMO
"International Service Web site".
• Voice call or video telephony features are not supported by
L-05A.
• If you subscribe to mopera U, visit the mopera U web site.
http://www.mopera.net/ (Japanese only)
Before Using Overseas
STEP1：Before Leaving Japan
STEP2：While Overseas
STEP3：After Coming Back to Japan
Before Leaving Japan
Before using the FOMA terminal overseas, refer to the
followings.
While Overseas
■ Switching networks
Searching for and connecting to an access point are
performed automatically by default. No special settings
are required.
■ Main screen display area
The name of the connected carrier can be viewed in the
display area of the Main screen.→P116
• "Mobile Phone User's Guide [International Services]"
• "Mobile Phone User's Guide [Network Services]"
• DOCOMO "International Service Web site"
差替え予定
■ Subscription
• If you subscribed to the FOMA service after September 1,
2005, no separate subscription is required to use ″WORLD
WING″. If you subscribed to the FOMA service on or before
August 31, 2005 and have not subscribed to ″WORLD
WING″, a separate subscription is required to use it.
• A FOMA card (green/White) made available for WORLD
WING must be inserted in the FOMA terminal.
■ Power source and voltage in the country or region of
stay
• Countries and regions may have different power sources,
voltages or power outlet shapes. Check these in the
instruction manual for your PC or web sites of the PC
manufacturer in advance.
■ Network setup
• You can change network setup from overseas.→P116
■ Internet access
• For overseas access points or settings for using the
Internet overseas, contact your Internet service provider.
Note
• You can manually switch networks if you want to connect
to a particular network. See procedure 3 of "ネットワークを
設定する (Configuring Networks)" (P116)
Inquries overseas
If your FOMA card (green/white) is lost or stolen overseas,
contact DOCOMO immediately and temporarily suspend
your subscription. For inquiry information, see "docomo
Information Center" on the back of this manual. Call or data
communication charge will still on you after the terminal
was lost or stolen.
Overseas Use
113
■ Country Codes for Major Countries
Area
U.S.A
Code
■ International Access Codes for Major Countries (Table 1)
Area
Germany
Code
49
U.K.
44
Turkey
90
Italy
39
Japan
81
India
91
New Caledonia
687
Indonesia
62
New Zealand
64
Egypt
20
Norway
47
Australia
61
Hungary
36
Austria
43
Fiji
679
Netherlands
31
Philippines
63
Canada
Finland
358
Korea
82
France
33
Greece
30
Brazil
55
Singapore
65
Vietnam
84
Switzerland
41
Peru
51
Sweden
46
Belgium
32
Spain
34
Hong Kong
852
Thailand
66
Macau
853
Taiwan
886
Malaysia
60
Tahiti
689
Maldives
960
Czech
420
Russia
China
86
※ For country code or detailed information, refer to "Mobile
Phone User's Guide [International Services]" or DOCOMO
"International Service Web site".
114
Overseas Use
Area
Ireland
Code
00
Area
Germany
Code
00
U.S.A.
011
Turkey
00
U.A.E.
00
New Zealand
00
U.K.
00
Norway
00
Italy
00
Hungary
00
India
00
Philippines
00
Indonesia
001
Finland
00
Australia
0011
France
Netherlands
00
Canada
011
Korea
001
Vietnam
00
Greece
00
Belgium
00
Singapore
001
Poland
00
Switzerland
00
Portugal
00
Sweden
00
Hong Kong
001
Spain
00
Macau
00
Brazil
00
0021
0014
Thailand
001
Malaysia
00
Taiwan
002
Monaco
00
Czech
00
Luxembourg
00
China
00
Russia
810
Denmark
00
※ For codes of other countries or details, visit DOCOMO
"International Service Web site".
■ International Phone Codes for Universal Number(Table 2)
Area
Ireland
Code
Area
Code
00
Taiwan
00
U.S.A.
011
China
00
Argentina
00
Denmark
00
U.K.
00
Germany
00
Israel
014
New Zealand
00
Italy
00
Norway
00
Australia
0011
Hungary
00
Austria
00
Philippines
00
Netherlands
00
Finland
990
Canada
011
France
00
Korea
001
Brazil
0021
Colombia
009
Belgium
00
Singapore
001
Portugal
00
Switzerland
00
Hong Kong
001
Sweden
00
Malaysia
00
Spain
00
South Africa
09
Thailand
001
Luxembourg
00
After Coming Back to Japan
After coming back to Japan, the FOMA network will be
connected automatically.
■ If connection can not be established
Set to "自動検索(Auto)" from "ネットワーク検索(Search
Network )" of "ネットワークを設定する(Configuring network)"
(P116)
Setting the Searching Method
for Available Networks
Switching Carriers Manually
The FOMA terminal is set to automatically find and switch
to an available network in the country of stay by default.
However, if you have a preferred network in the area or
network cannot be found automatically, you can set to a
network manually. For details, see "Configuring Networks"
(P116).
※ For codes of other countries or details, visit DOCOMO
"International Service Web site".
Overseas Use
115
c
Configuring Network
Click
※ If network search mode is set to "manual" overseas,
reset to "Auto" after coming back to Japan.
from the application option screen
適用 (Application)
優先ネットワーク (Prior network)
■ 表示しない(Hide)
The name of the network receiving current service is
not displayed on the screen.
ネットワーク検索
(Network Search)
ネットワーク情報
(Network Information)
116
Specify a "優先ネットワーク(Prior network)"
(Network priority order selection setting)
Overseas Use
Specify if display or hide the network
information
■ 表示する(Display)
The name of the network receiving current service is
displayed on the screen.
適用 (Application)
適用 (Application)
■ 自動検索(Auto)
Network can be searched automatically.
■ 手動検索(Manual)
Connect to the listed networks manually.
• Allow you to configure network by L-05A connection software.
Searching network
Click the applicable
Click
• The information entered will not be set without clicking the
applicable
Note
• How to manually configure network
- Select "手動選択(Manual)"
- The available network list will be displayed after
searching.
- Select one from the available networks.
- Click
• Network is not displayed in FOMA area when even if
"display" is set in network information.
• Connecting to Internet or sending SMS may not be able to
operate properly when network setting is changed
manually.
• While using Oversea→P111
- When you are in roaming area and set FOMA terminal to
automatically find and you can have automatic roaming
service. If network can not be found automatically,
select the available network service manually.
- Some communication services may not available
depending on the overseas carrier or network.
Overseas Use
117
Appendix/Troubleshooting
AT Commands ･･･････････････････････････････････
AT Command List････････････････････････････････
Troubleshooting ･････････････････････････････････
Error Messages･･････････････････････････････････
Warranty and After-Sales Service ･･･････････････
Updating software ･･･････････････････････････････
Main specifications ･･････････････････････････････
Export Controls of the Product and Accessories ･･･
Intellectual Property Rights ･････････････････････
Index ･････････････････････････････････････････････
120
121
130
132
134
135
136
137
139
141
119
AT Commands
AT commands are used to check the FOMA terminal
function settings or status by using a PC. Usually, the
communication software issues AT commands so you do
not need to be concerned about them. Use AT commands if
you want to control the FOMA terminal in your own way.
Form of AT Commands
AT commands should be entered on the Terminal Mode
screen of the communication software. Use only singlebyte alphanumeric characters.

ATD ＊ 99 ＊＊＊ 3#
Hard Return
Parameter: Content
Command Name
• An AT command must be entered on a single line including
parameters (numbers and symbols) following the command. On
the Terminal Mode screen of the communication software,"one
line" is from the first character to the character before
Note
• In the Terminal mode, a PC functions as a communication
terminal. Characters entered from the keyboard are sent to
a line connected to a communication port.
120
Appendix/Troubleshooting
AT Command List
The following AT commands can be used on the ″L-05A″modem port.
• [&F]：A command to initialize settings used as AT&F command.
• [?][=?]：The current settings appear when adding″?″at the end of the command, and the effective range of the current
settings appears when adding″=?″at the end of the command.
Command
Overview
Comments
Examples
Parameters/Description
AT&C
Select the operating conditions of the
circuit CD for DTE
n=0: Always keeps CD singal ON
n=1 (default): CD changes depending
on the other party's modem status.
AT&C1
OK
AT&F
Reset the FOMA terminal AT command
set values to factory defaults If
executed during a communication, the
line is disconnected.
Only n=0 can be set (Skippable)
AT+CGDCONT [?] [=?]
Set APN when sending Packet
communication.
Refer to P128
Refer to P128
AT+CGEQMIN [?] [=?]
Register criteria value for determining if
QoS (Quality of Service) sent from
network when PPP Packet
communication is established, is
acceptable or not.
Refer to P128
Refer to P128
AT+CGEQREQ [?] [=?]
Set QoS(Quality of Service) to request
for the network when PPP Packet
communication is established.
Refer to P128
Refer to P128
AT+CGMR
Display the version of the AT+CGMR
FOMA terminal.
AT+CGMR
1234567890123
456
OK
Appendix/Troubleshooting
121
Command
AT+CGREG=
[&F]
[?] [=?]
122
Overview
Set whether to be notified of the
network registration status.
Comments
Examples
Parameters/Description
＜n＞
n=0(default): Do not note.
n=1: Notify when outside and inside the
service area is changed.
Execute「AT+CGREG?」
then appears as
｢+CGREG:,」
AT+CGREG?
+CGREG: 0,1
＜state＞
0:Not registered
1:Registered Home Network
4: Unknown
5: Registered (while roaming)
OK
OK
AT+CGREG=?
+CGREG: (0-2)
AT+CGSN
Display the serial number of the FOMA
terminal.
AT+CGSN
12345678901
2345
OK
AT+CMEE=
[&F]
[?] [=?]
Set the error report form of the FOMA
terminal.
n=0: Display「ERROR」
n=1: Display in the form of 「+CMEE
ERROR: xxxx」(where xxxx are
numbers)
n=2(default): Display in the form of
「+CMEE ERROR: xxxx」(where xxxx
are text)
※ If using ATZ or AT&F command to
default, "0" is setup.
Note that when connecting L-05A to
power, the value of ATZ or AT&F
command differs.
AT+CMEE=0
OK
Appendix/Troubleshooting
AT+CMEE?
+CMEE: 0
OK
AT+CMEE=?
+CMEE: (0, 1, 2)
OK
Command
AT+ CNUM
AT+COPS=
〔〔,
〔,〔,
〕〕〕
〕
[?] [=?]
Overview
Display the own number of the FOMA
terminal
Select and set carrier's name/Plmn
Number.
Comments
Examples
Parameters/Description
Executing「AT+CNUM」displays in the
form of「+CNUM: , 」
number: phone number
type=129: Excluding the international
access code+
type=145: Including the international
access code+
AT+CNUM
+CNUM:,″
09080189242″
,129
OK
AT+COPS?

+COPS: 0,0,”
”,2
0：Auto (Searching network
automatically and then change
OK
communication service)
1：Manual（to connect 
communication service)
2：Disconnection communication
AT+COPS=?
service
+COPS:（2,””,”
”
,”44010”,2）,
※Not supported
（3,”
”,””,”
3：Mapping don't excute.
4：Auto manual（In case, to disconnect 44020”,2）,,
communication service that （0,1,2,3,4）,
（0,1,2）
excute automatically）
※Not supported
OK

2：Fixed number
 represents country code(MCC)
plus network code(MNC).
“ 44010”is displayed for MCC=440
and MNC=10
Appendix/Troubleshooting
123
Command
Overview
AT+CPAS
[=?]
Display FOMA terminal state
AT+CPIN=″PIN″/
AT+CPIN=″PUK″
″PIN″
[?]
Command to enter the PIN code or
unblocking PIN code for FOMA card.
AT+CUSD
[&F]
Inquire the change or setting contents
of Internet configuration related to the
extra service.
Parameters/Description
Displays in the form of「+CPAS : 」. AT+CPAS
+CPAS:0
n=0: Available to set AT commands.
OK
n=3: Available and receiving
n=4: Available and receiving
AT+CPAS=?
+CPAS :（0,3,4）
OK
Enter the PIN1 code for ″PIN″, and
enter unblocking PIN code for ″PUK″.
Executing「AT+CPIN?」displays
「+CPIN: 」.
n=READY: Authenticated
n=SIM PIN: Waiting for entry
n=SIM PUK: Waiting for
unblocking PIN1 code entry
n=ERROR: Locked
Form : AT+CUSD=,""[,0]
n=0 : middle result
Do not send [,]
(default)
n=1 : middle result
Send [,]
Middle result :
m=0 : setting finishes
m=1 : information requirement from
network exists.
str
124
Appendix/Troubleshooting
Comments
Examples
:0∼9、＃、＊のみ使用可能。
は""で囲む
(+CPIN:SIM PIN
status) AT+CPIN=
″1234″
OK
(+CPIN:SIM PUK
status) AT+CPIN=
″
12345678″,″
1234″
OK
AT+CUSD=0,
"xxxxxxxxx"
OK
AT+CUSD=1,"＊
148＊1＊
0000#",0
+CUSD:0,"148＊
7#",0
OK
AT+CUSD=?
+CUSD: 0
OK
AT+CUSD=?
+CUSD:(0-2)
OK
Command
Overview
Comments
Examples
Parameters/Description
AT＊DANTE
Display the signal strength (number of
antenna bars) of the FOMA terminal.
AT＊DANTE
Result format:
＊DANTE:3
＊DANTE:
m=0 ：Out of the service area
OK
m=1 : State of 0 or 1 antenna bar
displayed
m=2 : State of 2 antenna bars displayed
m=3 : State of 3 antenna bars displayed
AT+GCAP
Display the capability list of the FOMA
terminal.
AT+GMI
Display the manufacturer of the FOMA
terminal.
AT+GMM
Display the name of the FOMA terminal. -
AT+GMR
Display the s/w version of the FOMA
terminal.
AT+GCAP
+GCAP:
+CGSM,+DS,+ES
OK
AT+GMI
LG Electronics Inc.
OK
AT+GMM
FOMA L05A
OK
AT+GMR
L05A-01-Vxxx440-10
OK
Appendix/Troubleshooting
125
Command
Overview
Comments
Examples
Parameters/Description
Set the local flow control method
n : DCE by DTE control
between the PC and the FOMA terminal. n=0 : No flow control.
n=1 : Perform XON/XOFF control.
n=2 (default): Perform RS/CS (RTS/
CTS) flow control.
m : DTE by DCE control.
m=0 : Perform No flow control.
m=1: XON/XOFF control.
m=2(default) : Perform RS/CS (RTS/
CTS) flow control
AT+IFC=2, 2
OK
AT+WS46=
[&F]
[?] [=?]
Set the wireless network to be used by
the FOMA terminal when dialing.
12: GSM
22: 3G (WCDMA)
25: GSM+3G (WCDMA)
AT+WS46?
25
A/
Retry a command just before performing
is not needed after entering
command.
A/
OK
ATD
Sending packet
Sending packet：ATD*99***
＜cid＞#
＜cid＞1∼10： +
Display the APN that configured
+CGDCONT
ATD*99***3#
CONNECT
7200000
ATE
[&F]
Set whether to echo back the text sent
from a PC.
n=0 : Not echo back.
n=1（default) : Echo back.
ATE1
OK
ATI
Display the recognition code
ATIO
n=0 : Display [NTT DOCOMO]
NTT DoCoMo
n=1 : Display the name of the FOMA
terminal（Same as +GMM）
n=2 : Display the FOMA terminal version OK
（same as +GMR）
n=3 : Display OK
n=4 : Display the details of
communication functions of the
FOMA terminal.
AT+IFC=,
[&F]
[?] [=?]
AT+IFC?
+IFC: 2,2
OK
OK
126
Appendix/Troubleshooting
Command
Overview
Comments
Examples
Parameters/Description
ATS3=
[&F] [?]
Set the return character (CR) to
recognize the end of AT command text
string.
n=13（default）: only n=13 can be
specified.
ATS3=13
OK
ATS4=
[&F] [?]
Set the line feed (LF) character. It is
positioned next to the return character
(CR) if displaying the result code in
alphanumeric characters.
Only n=10 (default) can be specified.
ATS4=10
OK
ATS5=
[&F] [?]
Set the back space (BS) character to
delete the last character in the input
buffer while AT commands are entered.
Only n=8 (default) can be specified.
ATS5=8
OK
ATV
[&F]
Set the display method of the result
code.
n=0 :Display in numeric characters.
n=1(default): Display in text.
ATV1
OK
ATZ
Reset the settings on the FOMA
terminal with the nonvolatile memory
contents. If performed during a
communication, the line is
disconnected.
ATZ
OK
Appendix/Troubleshooting
127
■ Command name: +CGEQMIN=[Parameter]
Supplementary Explanation of AT
Commands
■ Command name：+CGDCONT
• Overview
Set APN when sending packet connection.
• Form
+CGDCONT=[[,″″[,″″]]]
• Parameter descriptions
Set the destination (APN) when sending packets. See
the following examples for command operations.
※1：1∼10
※2：PPP or IP
※3：Optional
※1  is the number used to control the destination
(APN) for the packet communication to be registered in
FOMA terminal. 1 to 10 can be registered. The default
value of =1 is 「mopera.ne.jp」and =3 is
「mopera.net」. Set cid to 2 or a number between 4 and
10.
※2  is a protocol for packet communication.
※3  is optional string that indicates each destination.
• Command examples
Command to register an APN with the name of abc
(When PDP type is PPP, cid is 3）
AT+CGDCONT=2,″IP″,″abc″
OK
• Operations without a parameter
AT+CGDCONT=
：Clear all the settings of .
However, the setting of =1 or =3 is reset to
the value when purchasing.
AT+CGDCONT?：Display the current settings.
128
Appendix/Troubleshooting
• Overview
Register the threshold to accept the QoS (Quality of
Service) sent from the network when packet
communication is established.
• Format
+CGEQMIN=[,,[,]]]
• Parameter description
※1：1∼10
※2：None (default)
※2：None (default)
※1  is a number used to manage the access point
(APN) for the packet communication registered in the
FOMA terminal.
※2  and indicate the minimum communication speed [kbps] of
upload and download traffic respectively between the
FOMA terminal and the base station. If these are set to
None (default), all speeds are permissible. Be aware that a
packet communication may not be established because
any other speed than this is not permissible.
• Command examples
(1) Command to permit all speeds for both upload and
download (When cid=2)
AT+CGEQMIN=2
OK
(2) Command to permit only 5,700kbps for upload and
7,232kbps for download (When cid=2)
AT+CGEQMIN=2,,5700,7232
OK
(3) Command to permit 5,700kbps for upload and all speeds
for download (When cid=2)
AT+CGEQMIN=2,,5700
OK
(4) Command to permit all speeds for upload and only
7,232kbps for download (When cid=4)
AT+CGEQMIN=4,,,7232
OK
• Operations without a parameter
AT+CGEQMIN=：Reset all  to their defaults.
AT+CGEQMIN=：Reset the specified  to its
default.
• Operations without a parameter
AT+CGEQREQ=：Reset all  to their defaults
AT+CGEQREQ=：Set the specified  as
default.
Note
• This command, (+CGDCONT, +CGEQMIN, + CGEQREQ) is
not reset by [&F] and [Z], either.
■ Command name: +CGEQREQ=[Parameter]
• Overview
Set the QoS (Quality of Service) requested to the
network when packet communication is dialed.
• Format
+CGEQREQ=[[,,[,]]]
• Parameter description
※1：1∼10
※2：None (default)
※2：None (default)
※1  is a number used to manage the access point
(APN) for the packet communication registered in the
FOMA terminal.
※2  and indicate the minimum communication speed [kbps] of
upload and download traffic respectively between the
FOMA terminal and the base station. If these are set to
None (default), all speeds are permissible. Be aware that a
packet communication may not be established because
any other speed than this is not permissible.
Result Codes
■ List of result codes
Numeric
display
Text display
Description
OK
Operation performed properly
CONNECT
Connected to other party
NO CARRIER
Line disconnected
ERROR
Unable to accept command
• Command example
Command to require 5,700kbps for upload and
7,232kbps for download (When cid=2)
AT+CGEQREQ=2,2,5700,7232
OK
Appendix/Troubleshooting
129
Symptom
Troubleshooting
First, check whether software is required to update.
Update software if necessary. (Updating Software⇒P135)
Contact General Inquiries specified by DOCOMO located in
"Repairs" at the last page of the manual if the symptom is
not improved after confirming the check box.
■ The FOMA terminal is not recognized
FOMA terminal
is not
recognized
Check
Reinsert the FOMA terminal all the way into
the USB port securely.
Verify the L-05A Communication
Configuration Files (Drivers) for the FOMA
terminal functioning properly.→P35, P42
Communication may fail and the FOMA
terminal cannot be properly recognized and
functioned, if the PC is started up or restarted
with the FOMA terminal FOMA terminal left
inserted in it. In this case, remove and reinsert
the FOMA terminal. If communication fails
even after the FOMA terminal is inserted
again, remove it once, restart the PC, then
insert the FOMA terminal into the PC again.
When connecting the FOMA terminal with a
USB port, if data communication is not
available without being recognzied, double
click the "DOCOMO" icon recognized as a CD
drive or start "L-05A connection software" or
"DOCOMO connection manager" to recognize
the FOMA terminal as a modem.
The FOMA card will not be able to use if PIN1
unlock code is wrongly entered 10 times in a
low. For further information, visit DOCOMO
shop.
130
Appendix/Troubleshooting
■ Communication problems
Symptom
Communications
are not possible
■ Other problems
Check
Verify that signals are received in the
service area.
In the setting of Send Caller ID does not
conform to the provider's instructions,
communication may not be performed.→
P74, P90
Check if you set the FOMA Card Setting to
″PIN1 unblocking″.→P69
If set to (PIN1 Lock), launch the L-05A
connection software, then change FOMA
card setting to ″PIN1 unblocking″.→P71
Check the property settings of the modem
and the registration of the destination (APN)
■ Problems with AT Commands
Symptom
Symptom
Verify that the FOMA CARD is properly
inserted to FOMA terminal.→P19
The FOMA
terminal is not
detected if it is
inserted into a
USB port while
installing the
L-05A
Communication
Configuration
Files (Drivers).
Please confirm the followings.
• Whether the PC or OS you are using is in
the latest condition?
(If required, apply revision program of OS or
a maker.)
• Whether the FOMA terminal recognizes
normally when other USB devices are
inserted into the USB port?
• Whether the FOMA terminal operates
normally when being inserted into another
PC?
• Whether the FOMA terminal operates
normally when being reset to its default?
※：For inquiries related to OS or PC,
contact Microsoft or PC
manufactures.
Internet
connection
speed
decreased
significantly
Inserting FOMA terminal directly to a PC
may result in deterioration of performance
depending on the type of PC, specification
and degree of electromagnetic interference.
Check
[ERROR]
appears when a
command is
entered
Verify that you entered a correct
ATcommand.
[OK] does not
appear after an
AT command is
entered.
Check the L-05A Communication
Configuration Files (Drivers) have been
installed and functioned properly.
Check the properties of the terminal
software to see whether a device other than
the FOMA terminal is selected
Verify that the commands start with "AT" or
"at".
Check
The terminal
stopped working
suddenly
Your PC operating environments may have
changed because a new peripheral or
software was installed. Make a confirmation
with manufacturer or maker of accessory or
software.
Deterioration of performance may occur to
the service areas where W-CDMA/HSDPA/
GSM network are unstable. In this case,
move to other area and try to connect again.
Appendix/Troubleshooting
131
Error Messages
Error Messages
132
Description
圏外
You are out of service area or available network.
サービス地域ではありません。ネットワークを
再検索しますか?
You may be out of service area or available network, or network error. Please do network
setting again.
端末の認証に失敗しました。顧客センターまた
は代理店にお問い合わせください。
Communication may fail and the FOMA terminal cannot be properly recognized if the PC
is started up or restarted with the FOMA terminal left inserted in it. In this case, remove
and reinsert the FOMA terminal. If communication fails even after the FOMA terminal is
inserted again, remove it once, restart the PC, then insert the FOMA terminal into the
PC again. Contact DOCOMO shop if the same problems persist.
データ通信中には設定できません。終了後に設
定してください。
You cannot customize setting during data communication. Try again after closing data
communication.
変更するPIN１コードと確認用のPIN１コード
が異なります。
Two of new PIN1 are not identical each other. New PIN1 you want to change is not
matched to the PIN1 you entered for verification purpose. Enter correct PIN1.
FOMAカードが挿入されているか確認してくだ
さい。
Make sure to insert FOMA card into FOMA terminal before inserting to a PC.
FOMA端末が取り外されました。
Do not remove FOMA card while using FOMA terminal.
FOMA端末が取り付けられていません。
Verify the FOMA terminal is properly inserted into a PC. Verify that the FOMA terminal is
properly recognized by the PC.
PIN1を複数回間違えたため使用できなくなり
ました。（PIN1 blocked）PIN1コードがロッ
クされています。
An incorrect PIN1wasimproperly entered 3 times in a row. Available functions will be
limited. Enter PIN unblocking code to unlock.
PIN1コードが違います。残り（○/3）回入力
可能です。再入力してください。
An incorrect PIN1 code has been entered. Enter the correct PIN1 code again
PIN1コードが間違います。
（PIN1コードは
0123456789のみ使用できます。
）
You can use 0,1,2,3,4,5,6,7,8,9 as a valid PIN1 code. Others are invalid.
PIN1コードは4∼8文字です。
Valid PIN1 code is from 4 to 8 digit.
Appendix/Troubleshooting
Error Messages
Description
PIN1コードの変更はPINロックが設定されて
いるときに可能です。
To change the PIN1, PIN must be locked. Switch PIN unblocking to PIN blocking.
PINロック解除コードが違います。残り（○/
10）回入力可能です。再入力してください。
An incorrect PIN was imporperly entered 10 times in a row. Available functions will be
limited. Please enter the contact unblocking PIN code
SMS送信に失敗しました。
You may be out of service or available network.You may encounter problems due to the
network error.
PIN1ロック解除コードがブロックされている
ためFOMAカードを使用できません。顧客セン
ターにお問い合わせください。
You are no longer able to use FOMA card that PIN unblocking code has been improperly
entered10 times in a row. Please contact DOCOMO shop.
FOMA端末の初期化に失敗しました。FOMA端
末をリセットしてください。
Communication may fail and the FOMA terminal cannot be properly recognized, if the PC
is started up or restarted with the FOMA terminal left inserted in it. In this case, remove
and reinsert the FOMA terminal. If communication fails even after the FOMA terminal is
inserted again, remove it once, restart the PC, then insert the FOMA terminal into the
PC again.
送受信データなし。待ち受けモードに入りま
す。
When no data transmission has been incurred for a certain period of time.
Communication will be resumed when data transmission is incurred, so stay as it is.
Appendix/Troubleshooting
133
■ Replacement parts
Basically, replacement parts (parts required to maintain
product function) will be kept in stock for at least 4 years
after termination of production. Please note that the
product may not be repaired even during this period,
depending on the malfunctioning parts due to a shortage
of those parts. Depending on the nature of the required
repairs, it may still be possible to repair your terminal
even after this period. Contact ″Repairs″ listed on the
back of this manual.
Pay attention
• Do not modify the FOMA terminal, the FOMA card or its
accessories.
- Fire, injury or damage may result.
- If the FOMA terminal is modified (part replacement,
modification, painting, etc.), it will be repaired only after the
modified parts have been restored to the condition at the
time of purchase. However, repair may be refused depending
on the nature of modification.
･ Using sticker to decorate the FOMA terminal.
･ Exchanging the packing with those other than DOCOMO
product.
- Repair of failures or damage caused by modification are
charged even during the warranty period.
Updating software
Download the modification file of FOMA terminal from
download site on the Internet and then update the
software. If software update is necessary, you will be
informed at the DOCOMO web site with "お知らせ
（Information）".
Note
• Do not unplug the FOMA terminal with the computer during
software update.
• Software update (downloading and rewriting) may take a
while.
• If software update fails, all operations become unavailable.
In this case, bring your FOMA terminal to a DOCOMO
service center.
• Do not remove any inscription stickers attached to the FOMA
terminal. The inscription stickers certify that the FOMA
terminal satisfies specific technical standards. If stickers are
removed intentionally or are reattached in such a way that
confirmation of the sticker's contents is impossible, repair or
servicing may be refused because confirmation of whether or
not the device conforms to relevant technical standards
cannot be made.
Appendix/Troubleshooting
135
Main specifications
■ Operation system
Windows 2000 Professional Japanese version
(Service Pack 4 or later)
Windows XP Home Edition Japanese version
(Service Pack 2 or later)
Windows XP Professional Japanese version
(Service Pack 2 or later)
Windows Vista 32 bit Japanese version (Service Pack1
or later)
Windows Vista 64 bit Japanese version (Service Pack1
or later)
Mac OS X 10.4.11 Japanese version
Mac OS X 10.5.6 Japanese version
■ Communication Speed
Packet Communication:
Maximum receiving: 7.2Mbps（Best effort）
Maximum sending: 5.7Mbps（Best effort）
※ The maximum speed of 7.2Mbps for receiving and
5.7Mbps for sending is theoretical values and does not
show the actual ones.The actual communication speed
depends on communication environment and network
congestion.
※ Out of High-Speed area, the maximum communication
speed for receiving and sending is 384kbps
■ Operating environment
Temperature：5℃∼35℃
Humidity：45%∼85%
136
Appendix/Troubleshooting
■ Power source
Power voltage
DC5V±5%(Supplied from PC)
Max Current consumption
Max Current consumption while communicating
3G: Approx. 550mA or below
GSM/GPRS: Approx. 300mA or below
Average Current consumption while communicating
3G: Approx. 180mA or below
GSM/GPRS: Approx. 170mA or below
Average Current consumption while Standby:
3G: Approx. 90mA or below
GSM/GPRS: Approx. 90mA or below
※ Depending on the usage, power consumption fluctuates.
■ Form factor
USB connection type
■ Dimensions
Height: approx. 80mm
Width: approx. 32mm
Depth: approx. 13mm
■ Weight
Approx. 37g
Export Controls of the Product
and Accessories
Japan Export Control Regulations (″Foreign Exchange
and Foreign Trade Law″ and relevant laws and
regulations) and U.S. Reexport Regulations (Export
Administration Regulations: EAR) apply to this product and
its accessories. If you export or re-export this product or
its accessories, please follow the necessary procedures at
your own risk and expense. For details on the procedures,
contact the Ministry of Economy, Trade and Industry or the
U.S. Department of Commerce.
European Union Directives Conformance
Statement
FCC Regulations
Statement
This equipment has been tested and found to comply with
the limits for a class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
Hereby, LG Electronics, Inc. declares that this
product is in compliance with:
• Reorient or relocate the receiving antenna.
•The essential requirements and other relevant
provisions of Directive 1999/5/EC
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•All other relevant EU Directives
• Consult the dealer or an experienced radio/TV technician for
help.
0168
The above gives an example of a
typical Product Approval Number.
• Increase the separation between the equipment and receiver.
Change or Modifications that are not expressly approved
by the manufacturer could void the user's authority to
operate the equipment.
Appendix/Troubleshooting
137
Class B Compliance
This device and its accessories comply with part15 of FCC
rules.
Operation is subject to the following two conditions:
• This device & its accessories may not cause harmful
interference.
• This device & its accessories must accept any interference
received, including interference that may cause undesired
operation.
Body-worn Operation
Body-worn Operation
This Mobile Broadband USB Modem, model L-05A, is
This device
testedsize
for typical
approved
for has
usebeen
in normal
laptop body-worn
computers only
operations with the distance of 0.19inches (0.5cm) from
(typically
with
12"
or
larger
display
screens).
To comply
the user's body.
with
RFwith
exposure
this modem
To FCC
comply
FCC RF requirements,
exposure requirements,
a minimum
separation
distance
0.19inches(0.5cm)
must be
should
not be
used inofconfigurations
that cannot
maintained from the user's body.
maintain at least 5mm (approximately 0.2 inches) from
users and bystanders, and 12mm (approximately 0.47
inches)from the top of the USB modem. This USB
modem has been tested for compliance with FCC/IC RF
exposure limits in the laptop computer(s) configurations
with horizontal and vertical USB slots and can be used
in laptop computers with substantially similar physical
dimensions, construction, and electrical and RF
characteristics. This USB modem must not be used with
any other antenna or transmitter that has not been
approved to operate in conjunction with this modem.
138
Appendix/Troubleshooting
Consumer Information on SAR (Specific Absorption
Rate)
THIS DEVICE MEETS THE GOVERNMENT'S
REQUIREMENTS FOR EXPOSURE TO RADIO WAVES.
Your wireless device is a radio transmitter and receiver. It
is designed and manufactured not to exceed the emission
limits for exposure to radiofrequency (RF) energy set by
the Federal Communications 'Commission of the U.S.
Government. These limits are part of comprehensive
guidelines and establish permitted levels of RF energy for
the general population. The guidelines are based on
standards that were developed by independent scientific
organizations through periodic and thorough evaluation of
scientific studies.
The standards include a substantial safety margin
designed to assure the safety of all persons, regardless of
age and health. The exposure standard for wireless
devices employs a unit of measurement known as the
Specific Absorption Rate, or SAR.
The SAR limit set by the FCC is 1.6W/kg.
※ Tests for SAR are conducted using standard operating
positions specified by the FCC
with the device
transmitting at its highest certified power level, the actual
SAR level of the device while operating can be well below
the maximum value. This is because the device is
designed to operate at multiple power levels so as to use
only the power required to reach the network. In general,
the closer you are to a wireless base station antenna, the
lower the power output.
Before a device is available for sale to the public, it must be
tested and certified to the FCC that it does not exceed the
limit established by the government-adopted requirement
for safe exposure. The tests are performed in positions and
locations (e.g., worn on the body) as required by the FCC
for each model.
Intellectual Property Rights
Copyrights and Rights of Portrait
The highest SAR value for this device when worn on the
body is 1.17W/kg.
1.3W/kg.
The FCC has granted an Equipment Authorization for this
device with all reported SAR levels evaluated as in
compliance with the FCC RF emission guidelines. SAR
information on this device is on file with the FCC and can
be found under the Display Gant section of http://
www.fcc.gov/ after searching on FCC ID BEJL05A.
Additional information about Specific Absorption Rates
(SAR) can be found on the Cellular Telecommunications
Industry Association (CTIA) web-site
at http://www.wow-com.com.
Without permission of the copyright owner you may not
duplicate, modify, transmit over public communication
lines, etc. any document, image, music, software, or other
content owned by a third party that you have used this
product to download from an Internet web site, etc., except
for private uses such as duplication and indexing that are
allowed by copyright law.
Appendix/Troubleshooting
139

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
XMP Toolkit                     : 3.1-702
Modify Date                     : 2009:04:23 14:02:04-04:00
Create Date                     : 2009:04:23 14:01:49-04:00
Metadata Date                   : 2009:04:23 14:02:04-04:00
Creator Tool                    : FrameMaker 7.0
Format                          : application/pdf
Title                           : L05A_Manual_E.book
Creator                         : Administrator
Document ID                     : uuid:64a896d3-7dae-4d33-ac3c-ce0ddd1fdfa2
Instance ID                     : uuid:1ba97e81-8535-4dfa-b09c-562e28bcea97
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Has XFA                         : No
Page Count                      : 71
Author                          : Administrator

EXIF Metadata provided by EXIF.tools