LG Electronics USA LDS302 Bluetooth Module User Manual

LG Electronics USA Bluetooth Module Users Manual

Users Manual

Great Company Great People LG Electronics11 LGE KCC FCC CE Manual - 2012
Great Company Great People LG Electronics22 ContentsRRF Receiver KCC / FCC/ CE Test Configuration - Install KCC/ FCC/ CE tool - KCC / FCC/ CE Tool PC Setup - KCC / FCC/ CE Tool Setup - KCC / FCC/ CE Window Tool Explain -- Reset -- Receive Test -- Transmit Mode ( Single Freq-Non Hopping ) -- Transmit Mode ( Hopping across all 79ch Freq ) -- Unmodulated mode ( CW ) -- FCC Dw ell Time Testing Mode
Great Company Great People LG Electronics33 Install KCC/FCC/CE ToolGXU jGGGGGˈhwT\U_U[U_XWTtz~ZYT_]UˉSGˈiXU\UWU`UˉSGˈjwYXW}jw~wzYrZ}^UˉGGGGGGGGmUXGGYUGlˈhwT\U_U[U_XWTtz~ZYT_]UˉGGGhGUGGZUGlˈjwYXW}jw~YrwzYrZUˉGGGGGGGG|ziGkUGG[UGlGˈiXU\UWU`UˉGGGGGGGGiG{GGG\UGGlGGˈi{UˉGGGiG{GGGGGGGGmUYGGFig.2Fig.1
Great Company Great People LG Electronics44 KCC/FCC/CE PC Config SetupFig.1 Fig.2XU jG|ziGqGGwjG|ziGwGG|ziGjGGYU zGˈ㐐㣅˧㉘㥉˧㥐㛨䑄˧G㐐㏘䊐ˉGGwjGmUXGGkGtmUYGGGGGGGGGGGGUGGZU jGGGGGGGkGGO[PGG[U jGGGGiGGkGGOGXX\YWWGPG
Great Company Great People LG Electronics55 KCC/FCC/CE PC SetupBLUETOOL SETUPGSTART BLUETOOLGBlueTool Version 1.5.0.9 was used for these procedures.1. Start BlueTool (Programs >Broadcom BlueTool >BlueTool).GG2. Enable the BlueTool log window (View > Log Window). The log window is used to verify commands issued and display the results of those commands.GGTRANSPORT SETUPG1. From the BlueTool Transport menu, select HCI Control.2. In the Select HCI Control Window Transport window:G UART setup—Enable the UART option, select the appropriate com port, set the baud rate to 1152003. Click OKGG.G
Great Company Great People LG Electronics66 KCC/FCC/CE PC SetupGRESET THE DEVICE UNDER TESTGThe device under test (DUT) should be reset before each procedure. In the HCI Control… window:G1. Clear (uncheck) and then reselect the HCI protocol active option.G2. From the shortcut menu, select 7.3: Host Controller & Baseband Commands (3 key).G3. In the main body of the window, double-click Reset to reset the DUT.GG
Great Company Great People LG Electronics77 RECEIVE TESTThis is a non-hopping, write receive only test. To put the DUT in receive mode:G1. In the HCI Control window, from the shortcut menu, select 0: Vendor Specific Command (0 key).G2. In the main body of the window, double-click Write_Receive_Only.G3. In the HCI Command: Write_Recieve_Only window, enter the desired frequency (Low: 2402 MHz, Mid: 2441 MHz, High: 2480 MHz).GThe last line of the BlueTool log window will read Status = 0x0 (0, "Success").GG
Great Company Great People LG Electronics88 Transmit Mode(Single Freq-Non Hopping)GTo set the transmit carrier frequency arm:G1. Reset the device (page 6).G2. In the HCI Control window, from the shortcut menu, select 0: Vendor Specific Command (0 key)G3. In the main body of the window, double-click Set Tx Carrier Frequency ArmG4. In the HCI Command… window:Ga. From the Carrier_Enable shortcut menu, select Carrier on.Gb. In the Carrier_Frequency… field, enter the desired output frequency. ( Low: 2402 , Mid : 2441 , High:2480 )c. From the Mode shortcut menu, select PRBS9.Gd. From the Modulation Type shortcut menu, select GFSK,8PSK, or QPSK. Note: Only one modulation type can be selected for a specific test instance, but all three types must be tested for FCC compliance.e. From the Transmit_Power shortcut menu, select Specify Power Table index. f. In the Transmit_Power_Table_Index Transmit_Power field, enter 0.GGG5. Click OK.GGGG()GG
Great Company Great People LG Electronics99 Transmit Mode(Hopping across all 79ch Freq)GACL Basic1. Reset the device (page 6).2. In the HCI Control window, from the shortcut menu, select 7.4: Informational Parameters (4 key).3. In the main body of the window, double-click Read BD ADDR.The last line of the BlueTool log window will contain the Bluetooth device address of the DUT.4. In the HCI Control window, from the shortcut menu, select 0: Vendor-specific Commands (0 key).5. In the main body of the window, double-click Tx_Test.GGG()GG
Great Company Great People LG Electronics110 Transmit Mode(Hopping across all 79ch Freq)G6. In the HCI Command… windowa. From the Local_Device_BD_ADDR shortcut menu, select the Bluetooth device address of the DUT. b. From the Hopping_Mode shortcut menu, select 79 channel.c. From the Modulation_Type shortcut menu, select PRBS9 Pattern.d. From the Logical_Channel shortcut menu, select ACL Basic. e. From the BB_Packet_Type shortcut menu, select DH5/3-DH5,DH3/3-DH3, or DH1/2-DH1.Note: Only one packet type can be selected for a specific test instance, but all three types must be tested for FCC compliance.f. In the BB_Packet_Length field, enter 65535g. From the Tx_Power_Level shortcut menu, select Specify Power Table index.h. In the Transmit_Power_Table_Index field, enter 0.GGG()GG7. Click OK.G
Great Company Great People LG Electronics111 Transmit Mode(Hopping across all 79ch Freq)GACL EDR1. Reset the device (page 6).2. In the HCI Control window, from the shortcut menu, select 7.4: Informational Parameters (4 key).3. In the main body of the window, double-click Read BD ADDR.The last line of the BlueTool log window will contain the Bluetooth device address of the DUT.4. In the HCI Control window, from the shortcut menu, select 0: Vendor-specific Commands (0 key).5. In the main body of the window, double-click Tx_Test.GGG()GG
Great Company Great People LG Electronics112 Transmit Mode(Hopping across all 79ch Freq)G6. In the HCI Command… windowa. From the Local_Device_BD_ADDR shortcut menu, select the Bluetooth device address of the DUT. b. From the Hopping_Mode shortcut menu, select 79 channel.c. From the Modulation_Type shortcut menu, select PRBS9 Pattern.d. From the Logical_Channel shortcut menu, select ACL EDR.e. From the BB_Packet_Type shortcut menu, select DH5/3-DH5,DH3/3-DH3, or DH1/2-DH1.Note: Only one packet type can be selected for a specific test instance, but all three types must be tested for FCC compliance.f. In the BB_Packet_Length field, enter 65535.g. From the Tx_Power_Level shortcut menu, select Specify Power Table index.h. In the Transmit_Power_Table_Index field, enter 0.GGG()GG7. Click OK.G
Great Company Great People LG Electronics113 Unmodulated mode(CW)GTo set the transmit carrier frequency arm:G1. Reset the device (page 6).G2. In the HCI Control window, from the shortcut menu, select 0: Vendor Specific Command (0 key)G3. In the main body of the window, double-click Set Tx Carrier Frequency ArmG4. In the HCI Command… window:Ga. From the Carrier_Enable shortcut menu, select Carrier on.Gb. In the Carrier_Frequency… field, enter the desired output frequency. ( Low: 2402 , Mid : 2441 , High:2480 )c. From the Mode shortcut menu, select PRBS9.Gd. From the Modulation Type shortcut menu, select Unmodulated. e. From the Transmit_Power shortcut menu, select Specify Power Table index. f. In the Transmit_Power_Table_Index Transmit_Power field, enter 0.GGG5. Click OK.GGGG()GG
Great Company Great People LG Electronics114 FCC Dwell Time Testing ModeGACL Basic1. Reset the device (page 6).2. In the HCI Control window, from the shortcut menu, select 7.4: Informational Parameters (4 key).3. In the main body of the window, double-click Read BD ADDR.The last line of the BlueTool log window will contain the Bluetooth device address of the DUT.4. In the HCI Control window, from the shortcut menu, select 0: Vendor-specific Commands (0 key).5. In the main body of the window, double-click Tx_Test.GGG()GG
Great Company Great People LG Electronics115 FCC Dwell Time Testing ModeG6. In the HCI Command… windowa. From the Local_Device_BD_ADDR shortcut menu, select the Bluetooth device address of the DUT. b. From the Hopping_Mode shortcut menu, select Single Frequency.c. From the Modulation_Type shortcut menu, select PRBS9 Pattern.d. From the Logical_Channel shortcut menu, select ACL Basic or ACL EDR. “ACL Basic” to test hopping channel in GFSK modulation mode or,“ACL EDR” to test hopping channel in 8PSK mode e. From the BB_Packet_Type shortcut menu, select DH5/3-DH5.Note: These are worst case packet duty cycles.f. From the Tx_Power_Level shortcut menu, select Specify Power Table index.g. In the Transmit_Power_Table_Index field, enter 0.GGG()GG7. Click OK.G
Great Company Great People LG Electronics116 KCC/FCC/CE Certification SetupjGymGORGymGPGjG{G{GGtGG|ziGqpnGRF Module or TVTest ToolUSB JIGSpectrumAnalyzerDUT
Great Company Great People LG Electronics117 USB JIG pin mapccG|ziGqpnGeGPin No.1
(4(4) Federal Communications Commission(FCC) Statement) Federal Communications Commission(FCC) StatementYou are cautioned that changes or modifications not expressly approved by You are cautioned that changes or modifications not expressly approved by the part responsiblethe part responsiblefor compliance could void the user’s authority to operate the equipmentfor compliance could void the user’s authority to operate the equipmentfor compliance could void the user s authority to operate the equipment.for compliance could void the user s authority to operate the equipment.This equipment has been tested and found to comply with the limits for a This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.Class B digital device, pursuant to part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful These limits are designed to provide reasonable protection against harmful it f i id tili tlltiit f i id tili tlltiinterference in a residential installation.interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a However, there is no guarantee that interference will not occur in a particular installationparticular installationparticular installation.particular installation.If this equipment does cause harmful interference to radio or television If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the the user is encouraged to try to correct the interference by one or more of the following measures:interference by one or more of the following measures:--. Reorient or relocate the receiving antenna.. Reorient or relocate the receiving antenna.--. Increase the separation between the equipment and receiver.. Increase the separation between the equipment and receiver.--. Connect the equipment into an outlet on a circuit different from that to . Connect the equipment into an outlet on a circuit different from that to which the receiver is connectedwhich the receiver is connectedwhich the receiver is connectedwhich the receiver is connected--. Consult the dealer or an experienced radio/TV technician for help.. Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:Operation is subject to the following two conditions:1) this device may not cause harmful interference, and1) this device may not cause harmful interference, and2) this device must accept any interference received, including interference 2) this device must accept any interference received, including interference that may cause undesired operation of the device.that may cause undesired operation of the device.Id lId lIndoor use onlyIndoor use onlyFCC Caution: Any changes or modifications not expressly approved by the FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate party responsible for compliance could void the user's authority to operate this equipment.this equipment.FCC RF Radiation Exposure Statement:FCC RF Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operateduncontrolled environment This equipment should be installed and operateduncontrolled environment. This equipment should be installed and operated uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. with minimum distance 20 cm between the radiator & your body. End users must follow the specific operating instructions for satisfying RF End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be coexposure compliance. This transmitter must not be co--located or operating in located or operating in conjunction with any other antenna or transmitterconjunction with any other antenna or transmitterconjunction with any other antenna or transmitter.conjunction with any other antenna or transmitter.
(5) (5) Industry Canada(IC) StatementIndustry Canada(IC) StatementThis device complies with RSSThis device complies with RSS--210 of the Industry Canada Rules.210 of the Industry Canada Rules.Operation is subject to the following two conditions:Operation is subject to the following two conditions:1) this device may not cause interference and1) this device may not cause interference and2) this device must accept any interference. Including interference that 2) this device must accept any interference. Including interference that may cause undesired operation of device.may cause undesired operation of device.This class B digital apparatus complies with Canadian ICESThis class B digital apparatus complies with Canadian ICES--003003Avis Avis d'Industried'Industrie CanadaCanadaCet appareil est conforme à norme CNRCet appareil est conforme à norme CNR--210 des règlements d'Industrie 210 des règlements d'Industrie Canada. Son fonctionnement est sujet aux deux conditions suivantes:Canada. Son fonctionnement est sujet aux deux conditions suivantes:1) Cet appareil ne doit pas provoquer d'interférences et1) Cet appareil ne doit pas provoquer d'interférences et2) Cet appareil doit accepter toute les interférences. y compris celles 2) Cet appareil doit accepter toute les interférences. y compris celles pouvant entraîner son dyspouvant entraîner son dys--fonctionnement.fonctionnement.Cet appareil numérique de classe B est conforme à la norme NMBCet appareil numérique de classe B est conforme à la norme NMB--003 003 du Canada.du Canada.
IC Radiation Exposure Statement:IC Radiation Exposure Statement:This equipment complies with IC radiation exposure limits set forth for an This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.uncontrolled environment.This equipment should be installed and operated with minimum distanceThis equipment should be installed and operated with minimum distanceThis equipment should be installed and operated with minimum distanceThis equipment should be installed and operated with minimum distance20 cm between the radiator & your body.20 cm between the radiator & your body.NOTE: THE MANUFACTURERE IS NO T RESPONSIBLE FOR ANY RADIO OR NOTE: THE MANUFACTURERE IS NO T RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY QQTO OPERATE THE EQUIPMENT.TO OPERATE THE EQUIPMENT.Avis d'Industrie Canada sur I'exposition aux rayonnementsAvis d'Industrie Canada sur I'exposition aux rayonnementsCet appareil est conforme aux limites d'exposition aux rayonnements Cet appareil est conforme aux limites d'exposition aux rayonnements pp p ypp p yd'Industrie Canaca pour unenvironnement non contrôlé.d'Industrie Canaca pour unenvironnement non contrôlé.II doit être installé de façon à garder une distance minimale de 20 II doit être installé de façon à garder une distance minimale de 20 centimètres entre la source de rayonnements et votre corps.centimètres entre la source de rayonnements et votre corps.REMARQUE: LE FABRICANT N'EST PAS RESPONSIBLE DES INTERFÉRENCES REMARQUE: LE FABRICANT N'EST PAS RESPONSIBLE DES INTERFÉRENCES RADIOÉLECTRIQUES CAUSÉES PAR DES MODIFICATIONS NON AUTORISÉES RADIOÉLECTRIQUES CAUSÉES PAR DES MODIFICATIONS NON AUTORISÉES APPORTÉES APPORTÉES À CET APPAREIL. DE TELLES MODIFICATIONS APPORTÉES APPORTÉES À CET APPAREIL. DE TELLES MODIFICATIONS POURRAIT ANNULER L'AUTORISATION ACCORDÉE À L'UTILISATEUR DE FAIRE POURRAIT ANNULER L'AUTORISATION ACCORDÉE À L'UTILISATEUR DE FAIRE FONCTIONNER L'APPAREIL.FONCTIONNER L'APPAREIL.

Navigation menu