LG Electronics USA LDS302 Bluetooth Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1586901
Application ID	bP0/Zaw5xedGh8/zK3w4Bg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	60.28kB (753488 bits)
Date Submitted	2011-11-23 00:00:00
Date Available	2012-05-21 00:00:00
Creation Date	2011-11-18 23:21:29
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2011-11-18 23:22:16
Document Title	PowerPoint 프레젠테이션
Document Creator	PowerPointìš© Acrobat PDFMaker 9.0
Document Author:	dwcho

LGE KCC FCC CE Manual - 2012
Great Company Great People
LG Electronics
Contents
„
R F Receiver K CC / FCC/ CE Test Configuration
I nstall K CC/ FCC/ CE tool
K CC / FCC/ CE Tool P C Setup
K CC / FCC/ CE Tool Setup
K CC / FCC/ CE W indow Tool Ex plain
-- Reset
-- Receive Test
-- Transm it M ode ( Single Freq-Non Hopping )
-- Transm it M ode ( Hopping across all 79ch Freq )
-- Unm odulated m ode ( CW )
-- FCC Dw ell Tim e Testing M ode
Great Company Great People
LG Electronics
Install KCC/FCC/CE Tool
Fig.1
Great Company Great People
Fig.2
XU jŒŠ’G
GGGGˈhŠ›ŒwŒ™“T\U_U[U_XWTtz~•ZYTŸ_]U”šˉSG
ˈi“œŒ›––“†šŒ›œ—†XU\UWU`UŒŸŒˉSG
ˈjwYXWŸ†}jw†~•†w†zYrZ†}š›ˆ†^UŒŸŒˉGG
GGGGGˆšGmŽUXG
YUGlŸŠœ›ŒˈhŠ›ŒwŒ™“T\U_U[U_XWTtz~•ZYTŸ_]U”šˉG
ž““G•š›ˆ““GhŠ›ŒG—Œ™“UG
ZUGlŸŠœ›ŒˈjwYXWŸ†}jw†~•Yr†w†zYrZUŒŸŒˉGG
GGGGž““G•š›ˆ““G|ziGk™Œ™UG
[UGlŸŠœ›ŒGˈi“œŒ›––“†šŒ›œ—†XU\UWU`UŒŸŒˉG
GGGGGž““G•š›ˆ““Gi“œŒG{––“G
\UGGlŸŒŠœ›ŒGGˈi“œŒ{––“UŒŸŒˉGž““G™œ•Gi“œŒG{––“GG
GGGGGˆšGmŽUYG
LG Electronics
KCC/FCC/CE PC Config Setup
Fig.1
Fig.2
XU j–••ŒŠ›G|ziGqŽGˆ•‹GwjG|ziGw–™›Gœš•ŽG|ziG
jˆ‰“ŒG
YU zŒ“ŒŠ›Gˈ㐐㣅˧㉘㥉˧㥐㛨䑄˧G㐐㏘䊐ˉG•GwjG
‚mŽUX„Gˆ•‹GkŒŠŒGtˆ•ˆŽŒ™‚mŽUY„G›–GšŒŒGG
›ŒG‹™Œ™GšGšœŠŠŒššœ““ G•š›ˆ““Œ‹G‰ GˆŠ›ˆ›•ŽG
›šG—–™›UG
ZU jŒŠ’G›ŒG•œ”‰Œ™G–GŠ–”G—–™›G•GkŒŠŒG
”ˆ•ˆŽŒ™GOŠ–”[PG
[U jŒŠ’G›ŒG•œ”‰Œ™G–Giˆœ‹™ˆ›ŒG•GkŒŠŒG
”ˆ•ˆŽŒ™GOGXX\YWWGPG
Great Company Great People
LG Electronics
KCC/FCC/CE PC Setup
BLUETOOL SETUPG
START BLUETOOLG
BlueTool Version 1.5.0.9 was used for these procedures.
1. Start BlueTool (Programs > Broadcom BlueTool > BlueTool).G
2.
Enable the BlueTool log window (View > Log Window). The log window is used to verify commands issued and display the results of those commands.
.G
TRANSPORT SETUPG
1.
From the BlueTool Transport menu, select HCI Control.
2.
In the Select HCI Control Window Transport window:G
UART setup—Enable the UART option, select the appropriate
com port, set the baud rate to 115200
3. Click OKG
Great Company Great People
LG Electronics
KCC/FCC/CE PC Setup
RESET THE DEVICE UNDER TESTG
The device under test (DUT) should be reset before each procedure. In the HCI Control… window:G
1. Clear (uncheck) and then reselect the HCI protocol active option.G
2. From the shortcut menu, select 7.3: Host Controller & Baseband Commands (3 key).G
3. In the main body of the window, double-click Reset to reset the DUT.G
Great Company Great People
LG Electronics
RECEIVE TEST
This is a non-hopping, write receive only test. To put the DUT in receive mode:G
1. In the HCI Control window, from the shortcut menu, select 0: Vendor Specific Command (0 key).G
2. In the main body of the window, double-click Write_Receive_Only.G
3. In the HCI Command: Write_Recieve_Only window, enter the desired frequency (Low: 2402 MHz, Mid: 2441 MHz, High: 2480 MHz).G
The last line of the BlueTool log window will read Status = 0x0 (0, "Success").G
Great Company Great People
LG Electronics
Transmit Mode(Single Freq-Non Hopping)
To set the transmit carrier frequency arm:G
1. Reset the device (page 6).G
2. In the HCI Control window, from the shortcut menu, select 0: Vendor Specific Command (0 key)G
3. In the main body of the window, double-click Set Tx Carrier Frequency ArmG
4. In the HCI Command… window:G
a. From the Carrier_Enable shortcut menu, select Carrier on.G
b. In the Carrier_Frequency… field, enter the desired output frequency. ( Low: 2402 , Mid : 2441 , High:2480 )
c. From the Mode shortcut menu, select PRBS9.G
d. From the Modulation Type shortcut menu, select GFSK, 8PSK, or QPSK.
Note: Only one modulation type can be selected for a specific test instance, but all three types must be tested for FCC compliance.
e. From the Transmit_Power shortcut menu, select Specify Power Table index. f.
In the Transmit_Power_Table_Index Transmit_Power field, enter 0.G
5. Click OK.G
()G
Great Company Great People
LG Electronics
Transmit Mode(Hopping across all 79ch Freq)
ACL Basic
1. Reset the device (page 6).
2. In the HCI Control window, from the shortcut menu, select 7.4: Informational Parameters (4 key).
3. In the main body of the window, double-click Read BD ADDR.
The last line of the BlueTool log window will contain the Bluetooth device address of the DUT.
()G
4. In the HCI Control window, from the shortcut menu, select 0: Vendor-specific Commands (0 key).
5. In the main body of the window, double-click Tx_Test.
Great Company Great People
LG Electronics
Transmit Mode(Hopping across all 79ch Freq)
6.
a.
b.
c.
d.
In the HCI Command… window
From the Local_Device_BD_ADDR shortcut menu, select the Bluetooth device address of the DUT.
From the Hopping_Mode shortcut menu, select 79 channel.
From the Modulation_Type shortcut menu, select PRBS9 Pattern.
From the Logical_Channel shortcut menu, select ACL Basic.
e. From the BB_Packet_Type shortcut menu, select DH5/3-DH5, DH3/3-DH3, or DH1/2-DH1.
Note: Only one packet type can be selected for a specific test instance,
but all three types must be tested for FCC compliance.
f. In the BB_Packet_Length field, enter 65535
g. From the Tx_Power_Level shortcut menu, select Specify Power Table index.
h. In the Transmit_Power_Table_Index field, enter 0.
()G
7. Click OK.G
Great Company Great People
LG Electronics
10
Transmit Mode(Hopping across all 79ch Freq)
ACL EDR
1. Reset the device (page 6).
2. In the HCI Control window, from the shortcut menu, select 7.4: Informational Parameters (4 key).
3. In the main body of the window, double-click Read BD ADDR.
The last line of the BlueTool log window will contain the Bluetooth device address of the DUT.
4. In the HCI Control window, from the shortcut menu, select 0: Vendor-specific Commands (0 key).
()G
5. In the main body of the window, double-click Tx_Test.
Great Company Great People
LG Electronics
11
Transmit Mode(Hopping across all 79ch Freq)
6.
a.
b.
c.
d.
e.
In the HCI Command… window
From the Local_Device_BD_ADDR shortcut menu, select the Bluetooth device address of the DUT.
From the Hopping_Mode shortcut menu, select 79 channel.
From the Modulation_Type shortcut menu, select PRBS9 Pattern.
From the Logical_Channel shortcut menu, select ACL EDR.
From the BB_Packet_Type shortcut menu, select DH5/3-DH5, DH3/3-DH3, or DH1/2-DH1.
Note: Only one packet type can be selected for a specific test instance,
but all three types must be tested for FCC compliance.
f. In the BB_Packet_Length field, enter 65535.
g. From the Tx_Power_Level shortcut menu, select Specify Power Table index.
h. In the Transmit_Power_Table_Index field, enter 0.
()G
7. Click OK.G
Great Company Great People
LG Electronics
12
Unmodulated mode(CW)
To set the transmit carrier frequency arm:G
1. Reset the device (page 6).G
2. In the HCI Control window, from the shortcut menu, select 0: Vendor Specific Command (0 key)G
3. In the main body of the window, double-click Set Tx Carrier Frequency ArmG
4. In the HCI Command… window:G
a. From the Carrier_Enable shortcut menu, select Carrier on.G
b. In the Carrier_Frequency… field, enter the desired output frequency. ( Low: 2402 , Mid : 2441 , High:2480 )
c. From the Mode shortcut menu, select PRBS9.G
d. From the Modulation Type shortcut menu, select Unmodulated.
e. From the Transmit_Power shortcut menu, select Specify Power Table index. f.
In the Transmit_Power_Table_Index Transmit_Power field, enter 0.G
5. Click OK.G
()G
Great Company Great People
LG Electronics
13
FCC Dwell Time Testing Mode
ACL Basic
1. Reset the device (page 6).
2. In the HCI Control window, from the shortcut menu, select 7.4: Informational Parameters (4 key).
3. In the main body of the window, double-click Read BD ADDR.
The last line of the BlueTool log window will contain the Bluetooth device address of the DUT.
()G
4. In the HCI Control window, from the shortcut menu, select 0: Vendor-specific Commands (0 key).
5. In the main body of the window, double-click Tx_Test.
Great Company Great People
LG Electronics
14
FCC Dwell Time Testing Mode
6.
a.
b.
c.
d.
In the HCI Command… window
From the Local_Device_BD_ADDR shortcut menu, select the Bluetooth device address of the DUT.
From the Hopping_Mode shortcut menu, select Single Frequency.
From the Modulation_Type shortcut menu, select PRBS9 Pattern.
From the Logical_Channel shortcut menu, select ACL Basic or ACL EDR.
“ACL Basic” to test hopping channel in GFSK modulation mode or,
“ACL EDR” to test hopping channel in 8PSK mode
e. From the BB_Packet_Type shortcut menu, select DH5/3-DH5.
Note: These are worst case packet duty cycles.
f. From the Tx_Power_Level shortcut menu, select Specify Power Table index.
g. In the Transmit_Power_Table_Index field, enter 0.
()G
7. Click OK.G
Great Company Great People
LG Electronics
15
KCC/FCC/CE Certification Setup
j–••ŒŠ›G{Œš›G{––“Gˆ•‹Gt–‹œ“ŒG
œš•ŽG|ziGqpnG
Test Tool
Spectrum
Analyzer
USB JIG
j–••ŒŠ›Œ‹GymGOˆ››Œ•œˆ›–™RGymGŠˆ‰“ŒPG
DUT
RF Module or TV
Great Company Great People
LG Electronics
16
USB JIG pin map
Pin No.1
cG|ziGqpnGeG
Great Company Great People
LG Electronics
17
(4)) Federal Communications Commission(FCC) Statement
(4
You are cautioned that changes or modifications not expressly approved by
the part responsible
for compliance could void the user
user’ss authority to operate the equipment
equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
i t f
interference
iin a residential
id ti l installation.
i t ll ti
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
installation
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following measures:
-. Reorient or relocate the receiving antenna.
-. Increase the separation between the equipment and receiver.
-. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
-. Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received, including interference
that may cause undesired operation of the device.
I d
Indoor
use only
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment
environment. This equipment should be installed and operated
with minimum distance 20 cm between the radiator & your body.
End users must follow the specific operating instructions for satisfying RF
exposure compliance. This transmitter must not be coco-located or operating in
conjunction with any other antenna or transmitter
transmitter.
(5) Industry Canada(IC) Statement
This device complies with RSSRSS-210 of the Industry Canada Rules.
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference. Including interference that
may cause undesired operation of device.
This class B digital apparatus complies with Canadian ICESICES-003
Avis d'Industrie Canada
Cet appareil est conforme à norme CNRCNR-210 des règlements d'Industrie
Canada. Son fonctionnement est sujet aux deux conditions suivantes:
1) Cet appareil ne doit pas provoquer d'interférences et
2) Cet appareil doit accepter toute les interférences. y compris celles
pouvant entraîner son dysdys-fonctionnement.
Cet appareil numérique de classe B est conforme à la norme NMB
NMB--003
du Canada.
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance
20 cm between the radiator & your body.
NOTE: THE MANUFACTURERE IS NO T RESPONSIBLE FOR ANY RADIO OR
TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT.
SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY
TO OPERATE THE EQUIPMENT.
Avis d'Industrie Canada sur I'exposition aux rayonnements
Cet appareil
pp
est conforme aux limites d'exposition
aux rayonnements
d'Industrie Canaca pour unenvironnement non contrôlé.
II doit être installé de façon à garder une distance minimale de 20
centimètres entre la source de rayonnements et votre corps.
REMARQUE: LE FABRICANT N'EST PAS RESPONSIBLE DES INTERFÉRENCES
RADIOÉLECTRIQUES CAUSÉES PAR DES MODIFICATIONS NON AUTORISÉES
APPORTÉES APPORTÉES À CET APPAREIL. DE TELLES MODIFICATIONS
POURRAIT ANNULER L'AUTORISATION ACCORDÉE À L'UTILISATEUR DE FAIRE
FONCTIONNER L'APPAREIL.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : dwcho
Company                         : TESCOM
Create Date                     : 2011:11:18 23:21:29+09:00
Modify Date                     : 2011:11:18 23:22:16+09:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Metadata Date                   : 2011:11:18 23:22:16+09:00
Creator Tool                    : PowerPoint용 Acrobat PDFMaker 9.0
Document ID                     : uuid:9d556e7a-8623-4d15-a0f8-d3e152340646
Instance ID                     : uuid:e1969eee-2c23-46ac-b9b6-e05f05c94664
Format                          : application/pdf
Title                           : PowerPoint 프레젠테이션
Creator                         : dwcho
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Page Count                      : 21

EXIF Metadata provided by EXIF.tools