LG Electronics USA LGSWFAC71 RF Module User Manual

LG Electronics USA RF Module

User Manual

User ManualPRODUCT NAME : 802.11a/b/g/n/ac MODEL NAME : LGSWFAC71(00)-0073The information contained herein is the exclusive property of LG Innotekand shall not be distributed, reproduced or disclosed in whole or no in partwithout prior written permission of LG Innotek.
User ManualPAGE :DOCUMENT No :REG. DATE : 2016.09.02MODEL NAME: TWFM-K008D(LGIT)LGSWFAC71(LGE)REV. DATE : 2016.09.02REV.NO : v0.01-Copyrightⓒ. 2016. All Rights Reserved.1/ 9IndexNo Description Page1 Features 22 Picture of Product 23 Installation Manual 34 Block Diagram 45 Absolute Maximum Ratings 46 Operating Conditions 57 Standard Test Conditions 58 Pin Description 6 9 Out Drawing 7 10 Packing Information 8
User ManualPAGE :DOCUMENT No :REG. DATE : 2016.09.02MODEL NAME: TWFM-K008D(LGIT)LGSWFAC71(LGE)REV. DATE : 2016.09.02REV.NO : v0.01-Copyrightⓒ. 2016. All Rights Reserved.2/ 92. Picture of Product1. FeaturesLGSWFAC71 is the small size and low power module for IEEE 802.11ac wireless LAN. TWFM-K008D is based on MTK MT7612U solution.IEEE 802.11 a/b/g/n/ac Dual Band WLAN infrastructureSize : 48.0mm x 30.0mmTwo stream spatial multiplexing up to 300Mbps(802.11n)/ 867Mbps(802.11ac)WLAN Metal Press antennaUse on-chip OTP (One-Time Programmable)Host Interface : USB2.0Security : WAPI, WEP, WPA, WPA2, WMM, AES, WEP, TKIP, CKPApplication: DTV, DVR, HD DVD Player, Blue-ray Disk Player, STBThis device is restricted to indoor use only within the 5.15 ~ 5.25 GHz Band.
User ManualPAGE :DOCUMENT No :REG. DATE : 2016.09.02MODEL NAME: TWFM-K008D(LGIT)LGSWFAC71(LGE)REV. DATE : 2016.09.02REV.NO : v0.01-Copyrightⓒ. 2016. All Rights Reserved.3/ 93. Installation ManualInstall the module like below in the back of the TVCableLGSWFAC71 installed position
User ManualPAGE :DOCUMENT No :REG. DATE : 2016.09.02MODEL NAME: TWFM-K008D(LGIT)LGSWFAC71(LGE)REV. DATE : 2016.09.02REV.NO : v0.01-Copyrightⓒ. 2016. All Rights Reserved.4/ 94. Block Diagram5. Absolute Maximum Ratings Parameter Min Max UnitStorage Temperature -20 +80 ℃Storage Humidity (40℃) - 90 %Caution : The specifications in Table 1 define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device.. Other conditions1) Do not use or store modules in the corrosive atmosphere, especially where chloridegas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. 2) Store the modules where the temperatureand relative humidity do not exceed 5 to 40℃and 20 to 60%.3) Assemble the modules within 6 months.Check the soldering ability in case of 6 months over.MT7612U2.4GHz5GHz2.4GHz5GHz11ac 2T2RBaseband32bit RISC CPUMAC /Packet buffer/Security engineSystemControlPMUUSB2.0InterfaceUSB I/F 8PIN CONNECTOR3.3VMain Clock40MHzDiplexerDiplexerANT0ANT1
User ManualPAGE :DOCUMENT No :REG. DATE : 2016.09.02MODEL NAME: TWFM-K008D(LGIT)LGSWFAC71(LGE)REV. DATE : 2016.09.02REV.NO : v0.01-Copyrightⓒ. 2016. All Rights Reserved.5/ 96. Operating Conditions Parameter Min Typ Max UnitAmbient Temperature 0 - 60 ℃Ambient Humidity (40℃) - - 85 %Supply Voltage 3.135 3.3 3.6 Vdc7. Standard Test ConditionsThe Test for electrical specification shall be performed under the following conditionOtherwise this following conditions, not guaranteed this performance.Temparature 25 ±5℃Humidity 65 ±5%Input Voltage Supply VoltageVDD_3.3V +3.3V ±0.165V7-1. Ambient condition7-2. Power supply voltages
User ManualPAGE :DOCUMENT No :REG. DATE : 2016.09.02MODEL NAME: TWFM-K008D(LGIT)LGSWFAC71(LGE)REV. DATE : 2016.09.02REV.NO : v0.01-Copyrightⓒ. 2016. All Rights Reserved.6/ 98. Pin DescriptionPin No. Pin Name I/O Pin Description1VCC I Power Supply 3.3V2 USB D- I/O USB Communication signal USB D-3 USB D+ I/O USB Communication signal USB D+4 GND I Ground5 WL_HOST_WAKE O Wake On WLAN6VCC I Power Supply 3.3V7 N.C - Not connected8 GND I Ground
User ManualPAGE :DOCUMENT No :REG. DATE : 2016.09.02MODEL NAME: TWFM-K008D(LGIT)LGSWFAC71(LGE)REV. DATE : 2016.09.02REV.NO : v0.01-Copyrightⓒ. 2016. All Rights Reserved.7/ 99. Outline Drawing'16. 07. 12'16. 07. 12Changsung Kim.Ilhee Park.Jangeun Yang.'16. 07. 12
User ManualPAGE :DOCUMENT No :REG. DATE : 2016.09.02MODEL NAME: TWFM-K008D(LGIT)LGSWFAC71(LGE)REV. DATE : 2016.09.02REV.NO : v0.01-Copyrightⓒ. 2016. All Rights Reserved.8/ 910. Packing Information• 1 Tray Package Q’ty : 120EA•Tray Material : Antistatic PET or Antistatic PS•1 Tray Weight : 0.2kg(1 Module Weight : 6.4 ±0.5g)• 1 Box Package Q’ty : 720EA•Box Size : A x B x C (512 x 377 x 121.5)•Box Material : Corrugated Fibreboards•1 Box Packing Weight : 6.3 ±0.4kg• Tray Stacking Q’ty :6 Stack(Zigzag stack)Corrugated FibreboardTrayInner Box• Total Packing Q’ty : 1,440EA•Total Packing Weight : 12.6±0.8kgPP BandBarcode LabelRoHS Marking•RoHS Marking :Label, Stamp, Printing•Marking Color : Gray or Red for Stamp, Label, Printing on the board and etc.Black only for Printing on Label. 10-1. Inner Box packing
User ManualPAGE :DOCUMENT No :REG. DATE : 2016.09.02MODEL NAME: TWFM-K008D(LGIT)LGSWFAC71(LGE)REV. DATE : 2016.09.02REV.NO : v0.01-Copyrightⓒ. 2016. All Rights Reserved.9/ 9 10-2. Carton Box Packing
User ManualPAGE :DOCUMENT No :REG. DATE : 2016.09.02MODEL NAME: TWFM-K008D(LGIT)LGSWFAC71(LGE)REV. DATE : 2016.09.02REV.NO : v0.01-Copyrightⓒ. 2016. All Rights Reserved.10 / 9Regulatory Notices1. FCCFCC Part 15.19 Statements:This device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) this device may not cause harmful interference, and (2) this device must accept anyinterference received, including interference that may cause undesired operation.FCC Part 15.21 statementAny changes or modifications not expressly approved by the party responsible for compliance couldvoid the user's authority to operate this equipment.FCC Part 15.105 statement This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions, may cause harmful interference toradio communications. However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.OEM Responsibilities to comply with FCC and Industry Canada RegulationsThe module has been certified for integration into products only by OEM integrators under thefollowing condition:- The antenna(s) must be installed such that a minimum separation distance of at least 20 cm ismaintained between the radiator (antenna) and all persons at all times.- The transmitter module must not be co-located or operating in conjunction with any other antennaor transmitter except in accordance with FCC multi-transmitter product procedures.As long as the two condition above is met, further transmitter testing will not be required. However,the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PCperipheral requirements, etc.).End Product Labeling The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and ICCertification Number are not visible when the module is installed inside another device, then theoutside of the device into which the module is installed must also display a label referring to theenclosed module. In that case, the final end product must be labeled in a visible area with thefollowing:“Contains FCC ID: BEJLGSBWAC71 “Contains IC: 2703H-LGSBWAC71”
User ManualPAGE :DOCUMENT No :REG. DATE : 2016.09.02MODEL NAME: TWFM-K008D(LGIT)LGSWFAC71(LGE)REV. DATE : 2016.09.02REV.NO : v0.01-Copyrightⓒ. 2016. All Rights Reserved.11 / 92. ICRSS-GEN, Sec. 7.1.3 –(licence-exempt radio apparatus) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject tothe following two conditions: (1) this device may not cause interference, and (2) this device mustaccept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radioexempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doitpas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillageradioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.RF ExposureThe antenna (or antennas) must be installed so as to maintain at all times a distance minimum ofat least 20 cm between the radiation source (antenna) and any individual. This device may not beinstalled or used in conjunction with any other antenna or transmitter.l'exposition aux RFL’antenne (ou les antennes) doit être installée de façon à maintenir à tout instant une distanceminimum de au moins 20 cm entre la source de radiation (l’antenne) et toute personne physique.Caution: Any changes or modifications to this device not explicitly approved by manufacturer couldvoid your authority to operate thisequipment.Attention:Les changements ou modifications de cet appareil non expressément approuvé par le fabricantpeuvent annuler votre droit à utiliser cet équipement.É tiquetage du produit final (IC) Le module BT111 est étiqueté avec sa propre identification FCC et son propre numéro decertification IC. Si l’identification FCC et le numéro de certification IC ne sont pas visibles lorsquele module est installé à l’intérieur d’un autre dispositif, la partie externe du dispositif dans lequelle module est installé devra également présenter une étiquette faisant référence au module inclus.Dans ce cas, le produit final devra être étiqueté sur une zone visible avec les informationssuivantes :« Contient module émetteur identification FCC ID : BEJLGSWFAC71 « Contient module émetteur IC : 2703H-LGSWFAC71”3. CEHereby, ' LG Electronics USA, Inc.' declares that this LGSWFAC71 is in compliance with the essential requirements and other relevant provisions of directive 1999/5/EC.This device is restricted to indoor use only within the 5.15 ~ 5.25GHz Band.

Navigation menu