LG Electronics USA LGSWFAC71 RF Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3136274
Application ID	zIP70R6LNpRA+YDzybFBiQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	44.97kB (562089 bits)
Date Submitted	2016-09-15 00:00:00
Date Available	2017-03-14 00:00:00
Creation Date	2016-09-08 09:32:59
Producing Software	Microsoft® PowerPoint® 2013
Document Lastmod	2016-09-08 09:32:59
Document Title	슬라이드 제목 없음
Document Creator	Microsoft® PowerPoint® 2013
Document Author:	박장순

User Manual
PRODUCT NAME : 802.11a/b/g/n/ac
MODEL NAME
: LGSWFAC71
The information contained herein is the exclusive property of LG Innotek
and shall not be distributed, reproduced or disclosed in whole or no in part
without prior written permission of LG Innotek.
(00)-0073
DOCUMENT No :
User Manual
REG. DATE : 2016.09.02
REV. DATE : 2016.09.02
REV.NO : v0.01
MODEL NAME: TWFM-K008D(LGIT)
LGSWFAC71(LGE) PAGE : 1 / 9
Index
No
Description
Page
Features
Picture of Product
Installation Manual
Block Diagram
Absolute Maximum Ratings
Operating Conditions
Standard Test Conditions
Pin Description
Out Drawing
10
Packing Information
Copyrightⓒ. 2016. All Rights Reserved.
DOCUMENT No :
User Manual
REG. DATE : 2016.09.02
REV. DATE : 2016.09.02
REV.NO : v0.01
MODEL NAME: TWFM-K008D(LGIT)
LGSWFAC71(LGE) PAGE : 2 / 9
1. Features
LGSWFAC71 is the small size and low power module for IEEE 802.11ac wireless LAN.
TWFM-K008D is based on MTK MT7612U solution.
 IEEE 802.11 a/b/g/n/ac Dual Band WLAN infrastructure
Size : 48.0mm x 30.0mm
 Two stream spatial multiplexing up to 300Mbps(802.11n)/ 867Mbps(802.11ac)
 WLAN Metal Press antenna
 Use on-chip OTP (One-Time Programmable)
 Host Interface : USB2.0
 Security : WAPI, WEP, WPA, WPA2, WMM, AES, WEP, TKIP, CKP
 Application: DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB
 This device is restricted to indoor use only within the 5.15 ~ 5.25 GHz Band.
2. Picture of Product
Copyrightⓒ. 2016. All Rights Reserved.
DOCUMENT No :
User Manual
REG. DATE : 2016.09.02
REV. DATE : 2016.09.02
REV.NO : v0.01
MODEL NAME: TWFM-K008D(LGIT)
LGSWFAC71(LGE) PAGE : 3 / 9
3. Installation Manual
Install the module like below in the back of the TV
LGSWFAC71 installed position
Cable
Copyrightⓒ. 2016. All Rights Reserved.
DOCUMENT No :
User Manual
REG. DATE : 2016.09.02
REV. DATE : 2016.09.02
REV.NO : v0.01
MODEL NAME: TWFM-K008D(LGIT)
LGSWFAC71(LGE) PAGE : 4 / 9
4. Block Diagram
2.4GHz
System
32bit RISC CPU
Diplexer
Control
5GHz
ANT1
USB I/F 8PIN CONNECTOR
MT7612U
ANT0
11ac 2T2R
MAC /
Baseband
2.4GHz
USB2.0
Packet buffer/
Diplexer
Interface
Security engine
5GHz
PMU
40MHz
3.3V
Main
Clock
5. Absolute Maximum Ratings
Caution : The specifications in Table 1 define levels at which permanent damage to the
device can occur. Function operation is not guaranteed under these conditions.
Operating at absolute maximum conditions for extend periods can adversely affect the
long-term reliability of the device.
Parameter
Min
Max
Unit
Storage Temperature
-20
+80
℃
Storage Humidity (40℃)
90
. Other conditions
1) Do not use or store modules in the corrosive atmosphere, especially where chloride
gas, sulfide gas, acid, alkali, salt or the like are contained.
Also, avoid exposure to moisture.
2) Store the modules where the temperature
and relative humidity do not exceed 5 to 40℃ and 20 to 60%.
3) Assemble the modules within 6 months.
Check the soldering ability in case of 6 months over.
Copyrightⓒ. 2016. All Rights Reserved.
DOCUMENT No :
User Manual
REG. DATE : 2016.09.02
REV. DATE : 2016.09.02
REV.NO : v0.01
MODEL NAME: TWFM-K008D(LGIT)
LGSWFAC71(LGE) PAGE : 5 / 9
6. Operating Conditions
Parameter
Min
Typ
Max
Unit
Ambient Temperature
60
℃
Ambient Humidity (40℃)
85
Supply Voltage
3.135
3.3
3.6
Vdc
7. Standard Test Conditions
The Test for electrical specification shall be performed under the following condition
Otherwise this following conditions, not guaranteed this performance.
7-1. Ambient condition
Temparature
25 ± 5℃
Humidity
65 ± 5%
7-2. Power supply voltages
Input Voltage
Supply Voltage
VDD_3.3V
+3.3V ±0.165V
Copyrightⓒ. 2016. All Rights Reserved.
DOCUMENT No :
User Manual
REG. DATE : 2016.09.02
REV. DATE : 2016.09.02
REV.NO : v0.01
MODEL NAME: TWFM-K008D(LGIT)
LGSWFAC71(LGE) PAGE : 6 / 9
8. Pin Description
Pin No.
Pin Name
I/O
Pin Description
VCC
Power Supply 3.3V
USB D-
I/O
USB Communication signal USB D-
USB D+
I/O
USB Communication signal USB D+
GND
Ground
WL_HOST_WAKE
Wake On WLAN
VCC
Power Supply 3.3V
N.C
Not connected
GND
Ground
Copyrightⓒ. 2016. All Rights Reserved.
DOCUMENT No :
User Manual
REG. DATE : 2016.09.02
REV. DATE : 2016.09.02
REV.NO : v0.01
MODEL NAME: TWFM-K008D(LGIT)
LGSWFAC71(LGE) PAGE : 7 / 9
9. Outline Drawing
'16. 07. 12
Jangeun Yang.
'16. 07. 12
Ilhee Park.
'16. 07. 12
Changsung Kim.
Copyrightⓒ. 2016. All Rights Reserved.
DOCUMENT No :
User Manual
REG. DATE : 2016.09.02
REV. DATE : 2016.09.02
REV.NO : v0.01
MODEL NAME: TWFM-K008D(LGIT)
LGSWFAC71(LGE) PAGE : 8 / 9
10. Packing Information
10-1. Inner Box packing
• 1 Tray Package Q’ty : 120EA
• Tray Material : Antistatic PET or Antistatic PS
• 1 Tray Weight : 0.2kg
(1 Module Weight : 6.4 ± 0.5g)
• Total Packing Q’ty : 1,440EA
• Total Packing Weight : 12.6± 0.8kg
Tray
• Tray Stacking Q’ty :6 Stack(Zigzag stack)
Corrugated Fibreboard
PP Band
• 1 Box Package Q’ty : 720EA
• Box Size : A x B x C (512 x 377 x 121.5)
• Box Material : Corrugated Fibreboards
• 1 Box Packing Weight : 6.3 ± 0.4kg
RoHS Marking
Barcode Label
• RoHS Marking :
Label, Stamp, Printing
• Marking Color :
Inner Box
Gray or Red for Stamp, Label,
Printing on the board and etc.
Black only for Printing on Label.
Copyrightⓒ. 2016. All Rights Reserved.
DOCUMENT No :
User Manual
REG. DATE : 2016.09.02
REV. DATE : 2016.09.02
REV.NO : v0.01
MODEL NAME: TWFM-K008D(LGIT)
LGSWFAC71(LGE) PAGE : 9 / 9
10-2. Carton Box Packing
Copyrightⓒ. 2016. All Rights Reserved.
DOCUMENT No :
User Manual
REG. DATE : 2016.09.02
REV. DATE : 2016.09.02
REV.NO : v0.01
MODEL NAME: TWFM-K008D(LGIT)
LGSWFAC71(LGE) PAGE : 10 / 9
Regulatory Notices
1. FCC
FCC Part 15.19 Statements:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC Part 15.21 statement
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment.
FCC Part 15.105 statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
OEM Responsibilities to comply with FCC and Industry Canada Regulations
The module has been certified for integration into products only by OEM integrators under the
following condition:
- The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is
maintained between the radiator (antenna) and all persons at all times.
- The transmitter module must not be co-located or operating in conjunction with any other antenna
or transmitter except in accordance with FCC multi-transmitter product procedures.
As long as the two condition above is met, further transmitter testing will not be required. However,
the OEM integrator is still responsible for testing their end-product for any additional compliance
requirements required with this module installed (for example, digital device emissions, PC
peripheral requirements, etc.).
End Product Labeling
The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC
Certification Number are not visible when the module is installed inside another device, then the
outside of the device into which the module is installed must also display a label referring to the
enclosed module. In that case, the final end product must be labeled in a visible area with the
following:
“Contains FCC ID: BEJLGSBWAC71
“Contains IC: 2703H-LGSBWAC71”
Copyrightⓒ. 2016. All Rights Reserved.
DOCUMENT No :
User Manual
REG. DATE : 2016.09.02
REV. DATE : 2016.09.02
REV.NO : v0.01
MODEL NAME: TWFM-K008D(LGIT)
LGSWFAC71(LGE) PAGE : 11 / 9
2. IC
RSS-GEN, Sec. 7.1.3 – (licence-exempt radio apparatus)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit
pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
RF Exposure
The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of
at least 20 cm between the radiation source (antenna) and any individual. This device may not be
installed or used in conjunction with any other antenna or transmitter.
l'exposition aux RF
L’antenne (ou les antennes) doit être installée de façon à maintenir à tout instant une distance
minimum de au moins 20 cm entre la source de radiation (l’antenne) et toute personne physique.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could
void your authority to operate thisequipment.Attention:
Les changements ou modifications de cet appareil non expressément approuvé par le fabricant
peuvent annuler votre droit à utiliser cet équipement.
É tiquetage du produit final (IC)
Le module BT111 est étiqueté avec sa propre identification FCC et son propre numéro de
certification IC. Si l’identification FCC et le numéro de certification IC ne sont pas visibles lorsque
le module est installé à l’intérieur d’un autre dispositif, la partie externe du dispositif dans lequel
le module est installé devra également présenter une étiquette faisant référence au module inclus.
Dans ce cas, le produit final devra être étiqueté sur une zone visible avec les informations
suivantes :
« Contient module émetteur identification FCC ID : BEJLGSWFAC71
« Contient module émetteur IC : 2703H-LGSWFAC71”
3. CE
Hereby, ' LG Electronics USA, Inc.' declares that this LGSWFAC71 is in compliance with the essential
requirements and other relevant provisions of directive 1999/5/EC.
This device is restricted to indoor use only within the 5.15 ~ 5.25GHz Band.
Copyrightⓒ. 2016. All Rights Reserved.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 12
Language                        : ko-KR
Tagged PDF                      : Yes
Title                           : 슬라이드 제목 없음
Author                          : 박장순
Create Date                     : 2016:09:08 09:32:59+09:00
Modify Date                     : 2016:09:08 09:32:59+09:00
Producer                        : Microsoft® PowerPoint® 2013
Creator                         : Microsoft® PowerPoint® 2013

EXIF Metadata provided by EXIF.tools