LG Electronics USA LTGEN90L Cellular/ PCS CDMA Automotive Transceiver Module with Bluetooth User Manual

LG Electronics USA Cellular/ PCS CDMA Automotive Transceiver Module with Bluetooth Users Manual

Contents

Users Manual

LG Telematics Test Manual [Gen90L] Version 1.0 2009.07.03
LG Telematics Revision History Author Description Date Sangjin Han Merged document. Document start July 3,2009
LG Telematics Contents 1. How to Place a Call 2. ATT Tool for TCU Setting 3. VCP Commander FCC information
LG Telematics 1. How to Place a Call Fig.9
LG Telematics
LG Telematics 2. ATT Tool for TCU Setting 1) Set COM Port Fig 18 2) Check Connection Status Fig.19
LG Telematics 3) NAD Screen Fig.20 4) Select Forced band mode and apply it Fig.21
LG Telematics - Click to see the selectable menu for changing - After select the Service mode, click “Control” to apply it. Fig.22 5) Check result of change. Fig.23
LG Telematics 3. VCP Commander 1) Run “VCP-Commander.exe”. This tool is single executable file. 2) Connect the named “CAIT”-port to your PC’s serial port. 3) Check the serial baud rate of VCP. (Power-up default is 38400 bps) 4) Select your PC’s COM-port, Press “Connect” button. 5) Test the right connection. Press “END”, verify that “Status” is flipped (“Cmd FAIL” to “Cmd OK”). Fig.25 6) Select command from drop-down-list and enter “Value 1” or “Value 2” according to each command. 7) Press “SET” button, then status is flipped. 8) Below table are command lists, value 1 and value 2. “Command” “Value 1” “Value 2”Description PREF_AUTOMATIC PREF_CELL_ONLY PREF_PCS_ONLY PREF_CDMA_ONLY PREF_ANALOG_ONLY PREF_HOME_ONLY Don’t care Don’t care Set system selection modePREF_P_REV_3 PREF_P_REV_4 PREF_P_REV_6 Don’t care Don’t care Set MOB_P_REV temporally
LG Telematics A_KEY See example 1 See example 1 Set A-key value PREF_FOR_RC 1 ~ 5 Don’t care Set NV_PREF_FOR_RC_I IMSI_MCC 3-digit decimal ie. “120” Don’t care Set NV_IMSI_MCC_I IMSI_11_12 2-digit decimal ie, “12” Don’t care Set NV_IMSI_11_12_I (MNC) SCM One-byte decimal Don’t care Set NV_SCM_I SLOT_SYCLE_INDEX 0 ~ 7 Don’t care Set NV_SLOT_CYCLE_INDEX_IMOB_TERM_HOME 0 or 1 Don’t care Enable(1) or Disable(0) MOB_TERM_FOR_SID 0 or 1 Don’t care Enable(1) or Disable(0) MOB_TERM_FOR_NID 0 or 1 Don’t care Enable(1) or Disable(0) Dial_SO2_LB, Dial_SO3_EVRC, Dial_SO9_LB13, Dial_SO54, Dial_SO55_LB, Dial_SO32768, Dial_SO32798, Dial_SO32799, Don’t care Don’t care Originate call with specified SO. Dial number is fixed to “111” internally.CALL_ANSWER Don’t care Don’t care Answer incoming call. CALL_END Don’t care Don’t care End call. Power_Down Don’t care Don’t care Force power-down “Communication Module” only. After this command, must do unplug then plug main VCP power to power-up Module. Power_Recycle Don’t care Don’t care Force power-recycle “Communication Module” only.
LG Telematics FCC Information FCC part 15.19 This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Part 15.21 statement Change or Modifications that are not expressly approved by the manufacturer could void the user's authority to operate the equipment. RF Exposure In order to comply with RF Exposure requirements the antenna or radiating element of this device must be installed to ensure that it is at least 20cm from end users. The antenna supplied with this device must not exceed a maximum gain of 9.74dBi in the cellular band and 8.25dBi in the PCS band. Installation This unit should only be installed by qualified personnel by GMOnstar. Address P.O. Box 430627 Pontiac, MI 48343

Navigation menu