LG Electronics USA MU50PZ90MQ Plasma Monitor User Manual 410Hen 50PZ90MQ
LG Electronics USA Plasma Monitor 410Hen 50PZ90MQ
User Manual
PLASMA MONITOR OWNER’S MANUAL MODEL : MU-50PZ90MQ Please read this owner’s manual thoroughly before operating the Monitor. Retain it for future reference. Record model number and serial number of the Monitor. See the label attached on the back of the Monitor and relate this information to your dealer if you ever require service. Model Number : Serial Number : P/NO : 3828VA0410H (RF03GB) Warning Warning WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. FCC NOTICE • A Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. • Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. WARNING TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. 2 Plasma Monitor Safety Instructions Safety Instructions Important safeguards for you and your new product Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference. Observing the simple precautions discussed in this booklet can help you get many years of enjoyment and safe operation that are built into your new product. This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association. 1. Read Instructions All the safety and operating instructions should be read before the product is operated. 9. Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards. 2. Follow Instructions All operating and use instructions should be followed. 10. Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to. 3. Retain Instructions The safety and operating instructions should be retained for future reference. 4. Heed Warnings All warnings on the product and in the operating instructions should be adhered to. 5. Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. Water and Moisture Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. 7. Accessories, Carts, and Stands Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer. 8. Transporting Product A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 11. Power Sources This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12. Power-Cord Polarization This product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin. This plug will only fit into the grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 13. Power-Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. PORTABLE CART WARNING Owner’s Manual 3 Safety Instructions Safety Instructions continued 14. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. Example of Grounding According to National Electrical Code Instructions Ground Clamp Antenna Lead in Wire Antenna Discharge Unit (NEC Section 810-20) Electric Service Equipment Grounding Conductor (NEC Section 810-21) Ground Clamps Power Service Grounding Electrode System (NEC Art 250, Part H) NEC - National Electrical Code 15. Lightning For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 16. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17. Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 18. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 4 Plasma Monitor 19. Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 20. Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. If the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e. If the product has been dropped or the cabinet has been damaged. f. If the product exhibits a distinct change in performance. 21. Replacement Parts When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 22. Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 23. Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. 24. Heat The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. Contents Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4 Low power . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Security PIP Operation . . . . . . . . . . . . . . . . . . .21 Menu Rotation For Vertical Viewing . . . . . . . . . .21 Screen Menu Options Auto Adjustment . . . . . . . . . . . . . . . . . . . . . . . .22 Setting Picture Format . . . . . . . . . . . . . . . . . . .22 Picture Size Zoom . . . . . . . . . . . . . . . . . . . . . .22 Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Screen Position . . . . . . . . . . . . . . . . . . . . . . . .23 Manual Configure . . . . . . . . . . . . . . . . . . . . . . .23 Screen Adjustments . . . . . . . . . . . . . . . . . . . . .24 Initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Selecting Wide VGA/XGA mode . . . . . . . . . . . .24 Luminance Noise Reduction . . . . . . . . . . . . . . .24 PIP (Picture-in-Picture) Feature Watching PIP . . . . . . . . . . . . . . . . . . . . . . . . . .25 PIP Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 PIP Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . .25 Swapping PIP . . . . . . . . . . . . . . . . . . . . . . . . . .25 Moving PIP . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Selecting an Input Signal Source for PIP . . . . . .25 Twin Picture Setup Options Watching Twin Picture . . . . . . . . . . . . . . . . . . . .26 Sub Picture Size Adjustment . . . . . . . . . . . . . . .26 Swapping the Twin Picture . . . . . . . . . . . . . . . .26 Selecting a Source for the Twin Picture . . . . . . .26 Introduction Controls and Connection Options . . . . . . . . . . . .7 Remote Control Key Functions . . . . . . . . . . . . . .8 Installation Installation Instruction . . . . . . . . . . . . . . . . . . . .9~10 External Equipment Connections . . . . . . . . . .11~14 VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Cable TV Setup . . . . . . . . . . . . . . . . . . . . . . . .11 External A/V Source Setup . . . . . . . . . . . . . . . .12 DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 DTV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . .13~14 Operation Turning on the Monitor . . . . . . . . . . . . . . . . . . . . .15 Menu Language Selection . . . . . . . . . . . . . . . . . .15 Video Menu Options APC (Auto Picture Control) . . . . . . . . . . . . . . . .16 Manual Picture Control . . . . . . . . . . . . . . . . . . .16 Auto Color Temperature Control . . . . . . . . . . . .16 Manual Color Temperature Control . . . . . . . . . .16 Audio Menu Options DASP (Digital Auto Sound Processing) . . . . . . .17 Manual Sound Control . . . . . . . . . . . . . . . . . . .17 AVL (Auto Volume Leveler) . . . . . . . . . . . . . . . .17 Time Menu Options Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .18 On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .18 Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Security PIP Time Setup . . . . . . . . . . . . . . . . . .19 Security Active . . . . . . . . . . . . . . . . . . . . . . . . .19 Special Menu Options Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 ISM Method . . . . . . . . . . . . . . . . . . . . . . . . . . .20 External Control Device Setup . . . . . . . . . . . . . . . .27~32 IR Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33~34 Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .35 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Setup and Operation Checklist Setup and Operation Checklist (See pages 11~13 for available connection and operational setup options.) 1. Unpack Monitor and all accessories. 5. Turn video source equipment on. 2. Connect all external video and audio equipment. see pages 11 ~ 14. 6. Select viewing source for Monitor. See page 8. 3 Install batteries in remote control. See page 8. 7. Fine-tune source image and sound to personal preference or as required by source. See pages 16 ~ 17. 4. Turn Monitor on. See page 15. 8. Additional features Setup See Contents above. After reading this manual, keep it handy for future reference. Owner’s Manual 5 Introduction Introduction What is a Plasma Display Panel (PDP)? If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that instant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon. 160° - Wide angle range of vision Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room. Wide Screen The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater. Multimedia Connect your plasma display to a PC and you can use it for conferencing, games, and internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously. Versatile The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs would not fit. The PDP Manufacturing Process: Why minute colored dots may be present on the PDP screen The PDP (Plasma Display Panel) which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several minute colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products and the tiny dots appearing does not mean that this PDP is defective. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology is designed to minimize cell defects during the manufacture and operation of this product. Cooling Fan Noise In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the PDP. The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not sufficient cause for the PDP to be exchanged or returned. 6 Plasma Monitor Introduction Controls Front Panel Controls - This is a simplified representation of front panel. Here shown may be somewhat different from your monitor. ON/OFF INPUT SELECT MENU VOL. E, D Main Power Button INPUT SELECT Button Buttons VOLUME (F,G) Buttons MENU Button Remote Control Sensor Power Standby Indicator Illuminates red in standby mode, Illuminates green when the Monitor is turned on. Connection Options Back Connection Panel - Connection panels shown may be somewhat different from your monitor. ( )R( ) R AUDIO L ( )L ( ) EXTERNAL SPEAKER RS-232C INPUT (CONTROL/SERVICE) DVI INPUT RGB INPUT AUDIO INPUT RGB OUTPUT REMOTE CONTROL 1. EXTERNAL SPEAKER (8 ohm output) Connect to optional external speaker(s). * For further information, refer to ‘Speaker & Speaker Stand’ manual. 2. RS-232C INPUT (CONTROL/SERVICE) PORT Connect to the RS-232C port on a PC. 3. DVI (Digital Visual Interface) INPUT/ RGB INPUT/AUDIO INPUT JACKS Connect the monitor output connector from a PC to the appropriate input port. 4. RGB OUTPUT PORT You can watch the RGB signal on another monitor, connect RGB OUTPUT to another monitor’s PC input port. 5. REMOTE CONTROL Connect your wired remote control to the remote control port on the Monitor. AUDIO INPUT PB PR COMPONENT INPUT R AUDIO L (MONO) ALARM S-VIDEO VIDEO INPUT AUDIO INPUT AC INPUT 6. COMPONENT INPUT/AUDIO INPUT JACKS Connect a component video/audio device to these jacks. 7. ALARM JACK Connect your alarm sensor to this jack. Detailed installation instruction is included in the alarm sensor owner’s manual. 8. S-VIDEO INPUTS Connect S-Video out from an S-VIDEO VCR to the S-VIDEO input. AUDIO/VIDEO INPUT JACKS Connect audio/video out from external equipment to these jacks. 9. POWER CORD SOCKET This Monitor operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the Monitor on DC power. Owner’s Manual 7 Introduction Remote Control Key Functions - When using the remote control, aim it at the remote control sensor on the monitor. - Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press the key again as necessary. POWER Switches the Monitor between ON and STANDBY. SECURITY Turn on the security PIP. APC Adjusts the factory preset picture according to the room. (Refer to p.16) ARC Changes the picture format. (Refer to p.22) PIP Switches the sub picture on or off. (Refer to p.25) INPUT SELECT Selects source: Video, S-Video, RGB, DVI, or Component mode. POWER SECURITY INPUT SELECT APC DASP ARC PIP ARC PIP TWIN PICTURE SWAP SUB INPUT MENU MUTE VOL OK VOL SUB INPUT Selects the input source for the sub picture. MUTE Switches the sound on or off. NUMBER buttons WIN. SIZE Adjusts the sub picture size. POWER STOP P/STILL REW PLAY FF WIN.POSITION Moves the sub picture. REC WIN.SIZE WIN.POSITION SPLIT ZOOM SPLIT ZOOM Enlarges the picture. ZOOM-/ZOOM+ Enlarges or reduces the main picture size. PIP ARC Changes the PIP picture format. (Refer to p.25) TWIN PICTURE (Refer to p.26) SWAP Exchanges main and sub picture images. (Refer to p.25, 26) MENU Displays on screen menus one by one. Exits the current menu. DASP To select the sound appropriate to your viewing program character: Flat, Music, Cinema, Sports, or User (Refer to p.17) ZOOM - ZOOM + SLEEP OK D /E Selects menu option. Memorizes menu changes. F / G (Volume button) Increases/decreases sound level. Adjusts menu settings. VCR BUTTONS Control some video cassette recorders. SLEEP Sets the Sleep Timer. (Refer to p.18) Installing Batteries • Open the battery compartment cover on the back side and insert the batteries with correct polarity. • Install two 1.5V batteries of AAA type. Don’t mix used batteries with new batteries. 8 Plasma Monitor Installation Installation Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product. POWER SECURITY INPUT SELECT APC DASP ARC PIP ARC PIP TWIN PICTURE SUB INPUT SWAP MENU VOL MUTE OK VOL 1.5V 1.5V Owner’s Manual D-sub 15 pin Cable POWER STOP REW PLAY P/STILL FF REC WIN.SIZE WIN.POSITION SPLIT ZOOM ZOOM - Batteries BNC-RCA Adapter ZOOM + SLEEP Remote Control DVI-D Cable Power Cord Installation Instructions • The Monitor can be installed in various ways such as on a wall, or on a desktop etc. • The plasma display is designed to be mounted horizontally or vertically. The speakers shown are optional. GROUNDING Power Supply Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Short-circuit Breaker Wall Mount: Horizontal installation For proper ventilation, allow a clearance of 4” on each side and 2” from the wall. Detailed installation instructions are available from your dealer, see the optional Wall Mounting Bracket Installation and Setup Guide. 2 inches 4 inches 4 inches 4 inches 4 inches Owner’s Manual 9 Installation Installation Instructions continued Desktop Pedestal Installation For proper ventilation, allow a clearance of 4” on each side and the top, 2.36” on the bottom, and 2” from the wall. Detailed installation instructions are included in the optional Desktop Stand Installation and Setup Guide available from your dealer. 4 inches 4 inches 2 inches 4 inches 2.36 inches Wall Mount: Vertical Vertical installation Detailed installation instructions are included in the optional Vertical Wall Mounting Bracket Installation and Setup Guide available from your dealer. NOTE: When installing the monitor vertically, the front panel controls must be in the left side position. When installing the monitor vertically, you have to change the OSD display mode so that the menus will appear correctly and also to protect the monitor from overheating (Refer to P. 21). 10 Plasma Monitor Installation External Equipment Connections NOTE: Not all cables shown are included with the plasma display. VCR Setup - To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor - Use the ISM Method feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed image may remain visible on the screen. How to connect 1. Connect the provided BNC-RCA adapter to the monitor’s VIDEO INPUT. 2. Connect the audio and video cables from the VCR's output jacks to the monitor input jacks, as shown in the figure. When connecting the monitor to VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). R AUDIO L AUDIO INPUT PB PR COMPONENT INPUT R AUDIO L (MONO) ALARM S-VIDEO VIDEO INPUT AUDIO INPUT Mono VCR: Connect the video output cable from the VCR to the VIDEO input on the monitor. S-VIDEO VCR: Connect the S-Video output cable from the VCR to the S-VIDEO input on the monitor. (Note that S-Video offers higher quality). How to use 1. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) 2. Use the INPUT SELECT button on the remote control to select Video. (If connected to S-VIDEO, select the S-Video input source.) S-VIDEO VCR OUT (R) AUDIO (L) VIDEO IN Cable TV Setup - After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming. The monitor cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the Monitor. - For further information regarding cable TV service, contact your local cable TV service provider(s). How to connect 1. Connect the provided BNC-RCA adapter to the monitor’s VIDEO INPUT. 2. Connect the audio and video cables from the Cable Box's output jacks to the monitor input jacks, as shown in the figure. When connecting the monitor to a Cable Box, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). R AUDIO L AUDIO INPUT PB PR COMPONENT INPUT R AUDIO L (MONO) ALARM S-VIDEO VIDEO INPUT AUDIO INPUT How to use 1. Use the INPUT SELECT button on the remote control to select Video. 2. Select your desired channel with the remote control for cable box. (R) AUDIO (L) VIDEO TV VCR RF Cable Cable Box Owner’s Manual 11 Installation External A/V Source Setup How to connect 1. Connect the provided BNC-RCA adapter to the monitor’s VIDEO INPUT. 2. Connect the audio and video cables from the external equipment's output jacks to the monitor input jacks, as shown in the figure. When connecting the monitor to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). R AUDIO L AUDIO INPUT PB PR COMPONENT INPUT R AUDIO L (MONO) ALARM S-VIDEO VIDEO INPUT AUDIO INPUT Camcorder How to use 1. Use the INPUT SELECT button on the remote control to select Video. 2. Operate the corresponding external equipment. Refer to external equipment operating guide. Video Game Set AUDIO VIDEO DVD Setup How to connect R AUDIO L AUDIO INPUT PB PR COMPONENT INPUT 1. Connect the DVD video outputs to the COMPONENT (Y, PB, PR) INPUT jacks and connect the DVD audio outputs to the AUDIO INPUT jacks on the monitor, as shown in the figure. 2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the monitor and connect the DVD audio outputs to the AUDIO INPUT jacks on the monitor, as shown in the figure. R AUDIO L (MONO) ALARM S-VIDEO VIDEO INPUT AUDIO INPUT How to use 1. Turn on the DVD player, insert a DVD. 2. Use the INPUT SELECT button on the remote control to select Component. (If connected to S-VIDEO, select the S-Video external input source.) 3. Refer to the DVD player's manual for operating instructions. (R) AUDIO (L) or (R) AUDIO (L) S-VIDEO • Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. DVD Component ports of the Monitor Video output ports of DVD player DTV Setup - To watch digitally broadcast programs, purchase and connect a digital set-top box. - This monitor supports HDCP (High-bandwidth Digital Contents Protection) protocol for DVI DTV (480p,720p,1080i) mode. R AUDIO L DVI INPUT RGB INPUT AUDIO INPUT RGB OUTPUT REMOTE CONTROL AUDIO INPUT PR PB Pr Pb B-Y R-Y Cb Cr PB PR PB PR COMPONENT INPUT R AUDIO L (MONO) ALARM S-VIDEO VIDEO INPUT AUDIO INPUT How to connect Use the monitor’s COMPONENT (Y, PB, PR) INPUT, RGB or DVI jack for video connections, depending on your set-top box connector. Then, make the corresponding audio connections. How to use 1. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) 2. Use INPUT SELECT on the remote control to select Component, RGB, or DVI. DVI-DTV OUTPUT (R) AUDIO (L) or or RGB-DTV OUTPUT (R) AUDIO (L) Digital Set-top Box 12 Plasma Monitor (R) AUDIO (L) Installation PC Setup - This monitor provides Plug and Play capability, meaning that the PC adjusts automatically to its settings. The monitor sends configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel (DDC) protocol. - The monitor perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. In this case, change the screen scanning rate for the graphic card. How to connect 1. To get the best picture quality, adjust the PC graphics card to a 1024x768, 60Hz. Resolutions over UXGA cannot be displayed. 2. Use the monitor’s RGB INPUT or DVI (Digital Visual Interface) INPUT port for video connections, depending on your PC connector. If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of either RGB INPUT or DVI INPUT to display the PC on the monitor. If the graphic card on the PC does output analog and digital RGB simultaneously, set the monitor to either RGB or DVI; (the other mode is set to Plug and Play automatically by the monitor.) 3. Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required. ( )R( ) ( )L ( ) EXTERNAL SPEAKER RS-232C INPUT (CONTROL/SERVICE) DVI INPUT RGB INPUT AUDIO INPUT RGB OUTPUT REMOTE CONTROL How to use 1. Turn on the PC and the monitor. 2. Turn on the display by pressing the POWER button on the monitor's remote control. 3. Use the INPUT SELECT button on the remote control to select RGB or DVI. 4. Check the image on your monitor. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. NOTES: • Depending on the graphics card, DOS mode may not work if you use a DVI-I cable. • Avoid keeping a fixed image on the monitor's screen for a long period of time. The fixed image may become permanently imprinted on the screen. Use the Orbiter screen saver when possible. • The synchronization input form for Horizontal and Vertical frequencies is separate. Owner’s Manual 13 Installation Monitor Display Specifications (RGB-PC / DVI-PC Mode) Resolution 640x350 720x400 640x480 800x600 832x624 848x480 14 Plasma Monitor Vertical Horizontal Frequency(KHz) Frequency(Hz) 31.468 70.09 Resolution Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.500 60.00 37.861 85.08 35.000 70.00 31.469 70.08 37.500 75.00 37.927 85.03 48.363 60.00 31.469 59.94 56.476 70.06 35.000 66.66 60.023 75.02 37.861 72.80 54.348 60.05 37.500 75.00 63.995 70.01 43.269 85.00 67.500 75.00 35.156 56.25 1280x960 60.000 60.00 37.879 60.31 1280x1024 63.981 60.02 46.875 75.00 47.700 60.00 53.674 85.06 59.625 75.02 49.725 74.55 47.700 60.00 31.500 60.00 59.625 75.02 35.000 70.00 37.500 75.00 852x480 1024x768 1152x864 1360x768 1366x768 Operation Operation Turning on the Monitor Turning on the Monitor just after installation 1. Connect power cord correctly. 2. Press the ON/OFF button on the Monitor. At this moment, the Monitor is switched to standby mode. Press the INPUT SELECT button on the Monitor or press the POWER, INPUT SELECT button on the remote control and then the Monitor will switch on. Turning on the Monitor (power cord is still connected) 1. If the Monitor was turned off with the • Press the ON/OFF button on the Monitor ON/OFF button on the Monitor to turn the Monitor on. 2. If the Monitor was turned off with the remote control and then the ON/OFF button on the Monitor • Press the ON/OFF button on the Monitor and then press the INPUT SELECT button on the Monitor or press the POWER, INPUT SELECT button on the remote control to turn the Monitor on. Menu Language Selection - The menus can be shown on the screen in the selected language. First select your language. 1. Press the MENU button and then use button to select the SPECIAL menu. VIDEO Language 2. Press the G button and then use D / button to select Language. AUDIO TIME 3. Press the G button and then use D / E button to select your desired language. From this point on, the on-screen menus will be shown in the language of your choice. SPECIAL Key lock ISM Method Low power Set ID Security OSD Rotate 한국어 English Español Português Français SCREEN 4. Press the OK button to save. TWIN MENU Prev. Owner’s Manual 15 Operation V ideo Menu Options - Video menu adjustment are unique to each input source. Readjust Video menu settings for each following input source as preferred. • RGB (PC) / DVI (PC), • RGB (DTV) / DVI (DTV) / Component (480p, 720p, 1080i) • Video / S-Video / Component (480i) APC (Auto Picture Control) - APC adjusts the Monitor for the best picture appearance. - When adjusting Video menu options (contrast, brightness, color, sharpness, and tint) manually, APC automatically changes to User. 1. Press the APC button repeatedly to select the picture appearance setup option as shown below. Clear Optimum Soft User • You can also adjust APC in the VIDEO menu. • Clear, Optimum, and Soft settings are preset for optimum picture quality at the factory and cannot be changed. Manual Picture Control ( User option) - You can adjust picture contrast, brightness, color, sharpness, and tint to the levels you prefer. 1. Press the MENU button and then use D /E button to select the VIDEO menu. VIDEO AUDIO 2. Press the G button and then use D / E button to select the desired picture option (Contrast, Brightness, Color, Sharpness, or Tint). 3. Press the G button and then use F /G TIME SPECIAL button to make appropriate adjustments. SCREEN APC ACC Color temp. Contrast 85 Brightness Color Sharpness Tint 60 50 50 4. Press the OK button to save. TWIN MENU Prev. Auto Color Temperature Control - To initialize values (reset to default settings), select the Normal option. - When adjusting color temperature options (red, green, and blue) manually, ACC automatically changes to User. 1. Press the MENU button and then use 2. Press the button and then use D /E D /E button to select the VIDEO menu. button to select ACC . 3. Press the G button and then use D / E button to select either Normal (Default), Cool (Preset), Warm (Preset), or User (Manual Adjustment). VIDEO AUDIO TIME SPECIAL APC ACC Color temp. Contrast Brightness Color Sharpness Tint 85 60 50 50 Normal Cool Warm User SCREEN 4. Press the OK button to save. TWIN MENU Prev. Manual Color Temperature Control ( User option) - You can adjust red, green, and blue to any color temperature you prefer. 1. Press the MENU button and then use 2. Press the G button and then use 3. Press the 4. Use the button and then use D F /G D /E D /E /E button to select the VIDEO menu. button to select the Color temp . button to select Red, Green, or Blue. button to make appropriate adjustments. • The adjustment range for Red, Green, and Blue is -20 ~ +20. 5. Press the OK button to save. 16 Plasma Monitor VIDEO AUDIO TIME SPECIAL APC ACC Color temp. Contrast Brightness Color Sharpness Tint SCREEN TWIN MENU Prev. 85 60 50 50 Red Green Blue Operation Audio Menu Options DASP (Digital Auto Sound Processing) - DASP lets you enjoy the best sound without any special adjustment because the Monitor has the appropriate sound options based on the program content. - When adjusting sound options (treble, bass, and balance) manually, DASP automatically changes to User. 1. Press the DASP button repeatedly to select the appropriate sound setup as shown below. Flat Music Cinema Sports User • You can also adjust DASP in the AUDIO menu. • Flat, Music, Cinema and Sports are preset for good sound quality at the factory and cannot be changed. Manual Sound Control ( User option) 1. Press the MENU button and then use D 2. Press the G button and then use (Balance, Treble, or Bass). 3. Press the button and then use /E D / E button to select the AUDIO menu. button to select the desired sound option VIDEO AUDIO TIME F /G button to make appropriate adjustments. DASP AVL Balance Treble 50 Bass 50 SPECIAL SCREEN 4. Press the OK button to save. TWIN MENU Prev. AVL (Auto Volume Volume Leveler) - This feature maintains an equal volume level; even if you change channels. 1. Press the MENU button and then use 2. Press the 3. Press the button and then use button and then use 4. Press the OK button to save. D /E D /E D /E button to select the AUDIO menu. button to select AVL. button to select On or Off. VIDEO DASP AUDIO AVL TIME Balance Treble Bass 50 50 On Off SPECIAL SCREEN TWIN MENU Prev. Owner’s Manual 17 Operation T ime Menu Options Clock Setup - If current time setting is wrong, reset the clock. 1. Press the MENU button and then use D /E button to select the TIME menu. 2. Press the button and then use D /E button to select Clock. 3. Press the button and then use D /E button to set the hour. 4. Press the button and then use D /E VIDEO AUDIO TIME SPECIAL button to set the minutes. Clock -- -- Off timer On timer Auto off Security set Security active SCREEN 5. Press the OK button to save. TWIN MENU Prev. On/Off On/Off Timer Setup - Timer function operates only if current time has been already set. - Off-Timer function overrides On-Timer function if they are set to the same time. 1. Press the MENU button and then use D /E button to select the TIME menu. VIDEO 2. Press the button and then use D /E button to select Off timer or On timer. AUDIO On timer 3. Press the G button and then use D / E button to select On. • To cancel On/Off timer function, select Off. TIME SPECIAL button and then use D /E button to set the hour. 5. Press the button and then use D /E button to set the minutes. button and then use Auto off Security set Security active On Off 12 Vol. 4. Press the 6. For only On timer function; Press the volume level. Clock Off timer SCREEN TWIN D /E MENU Prev. button to set 7. Press the OK button to save. Auto Off Off - If there is no input signal, the Monitor turns off automatically after 10 minutes. 1. Press the MENU button and then use D /E 2. Press the G button and then use D /E button to select Auto off. button to select the TIME menu. 3. Press the G button and then use D /E button to select On or Off. VIDEO AUDIO Clock Off timer On timer TIME Auto off SPECIAL 4. Press the OK button to save. Security set Security active SCREEN TWIN MENU Prev. Sleep Timer - The sleep timer turns the Monitor off at a preset time. Note that this setting is cleared when the monitor is turned off. zz 1. Press the SLEEP button repeatedly to select the number of minutes. First the --- Min option appears on the screen, followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes. 2. When the number of minutes you want is displayed on the screen, press the OK button. The timer begins to count down from the number of minutes selected. 3. To check the remaining minutes before the monitor turns off, press the SLEEP or OK button once. 4. To cancel the Sleep Timer, press the SLEEP button repeatedly until 18 Plasma Monitor zz --- Min appears. On Off 00 30 Operation Security PIP Time Setup - This is the function to set the time for security PIP operation. 1. Press the MENU button and then use D /E button to select the TIME menu. VIDEO 2. Press the 3. Press the button and then use D /E button to select Security set. button and then use D /E button to select Always or Time set. AUDIO TIME Clock Off timer On timer Auto off Security set • Select Always, if you want to operate the security PIP at all times. • Select Time set, if you want to set the desired time for security PIP operation. 4. When selecting Time set a. Press the G button and then use D b. Press the G button and then use D c. Press the G button and then use D d. Press the G button and then use D SPECIAL Always Time set From 23 Security active 00 30 To SCREEN TWIN 07 MENU Prev. button to set the desired beginning hour. / E button to set the desired beginning minutes. / E button to set the desired end hour. / E button to set the desired end minutes. /E 5. Press the OK button to save. Security Active - Set the time to keep on operating when turning the security PIP on. 1. Press the MENU button and then use D /E button to select the TIME menu. VIDEO 2. Press the 3. Press the button and then use D /E button to select Security active. button and then use D /E button to set the desired setting time. • The setting time range is 5 ~ 60 seconds. 4. Press the OK button to save. AUDIO TIME SPECIAL Clock Off timer On timer Auto off Security set Security active 10 Sec. SCREEN TWIN MENU Prev. Owner’s Manual 19 Operation Special Menu Options Key Lock - The monitor can be set up so that it can only be used with the remote control. - This feature can be used to prevent unauthorized viewing by disabling the front panel controls. - This Monitor is programmed to remember which option it was last set to even if you turn the monitor off. 1. Press the MENU button and then use 2. Press the button and then use 3. Press the G button and then use D /E button to select Key lock. D /E D /E button to select the SPECIAL menu. button to select On or Off. VIDEO AUDIO TIME SPECIAL • When you select On, the display ‘ on the front panel is pressed. Key lock’ appears on the screen if any button Language Key lock ISM Method Low power Set ID Security OSD Rotate On Off SCREEN TWIN 4. Press the OK button to save. MENU Prev. -In setting Key lock ‘On’, if the monitor is turned off with the remote control, press the INPUT SELECT button on the monitor or POWER, INPUT SELECT on the remote control to turn the monitor on. ISM (Image Sticking Minimization) Method - A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost image remaining; even when you change the image. Avoid allowing a fixed image to remain on the Monitor's screen for a long period of time. VIDEO 1. Press the MENU button and then use 2. Press the D /E button to select the SPECIAL menu. button and then use D /E button to select ISM Method. 3. Press the G button and then use Orbiter, or Inversion. D /E button to select either Normal, White wash, AUDIO Language Key lock ISM Method TIME SPECIAL Low power Set ID Security OSD Rotate Normal White wash Orbiter Inversion SCREEN • Normal If image sticking is never a problem, ISM is not necessary - set to Normal. TWIN MENU Prev. • White wash White Wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear entirely with White Wash. To return to normal viewing, press the any button. • Orbiter Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the image will move every 1 minutes: Right → Right → Downside → Downside → Left → Left → Upside → Upside. • Inversion Inversion will automatically invert the plasma display panel color every 30 minutes. 4. Press the OK button to save. Low Power - Low power reduces the plasma display's power consumption. 1. Press the MENU button and then use D /E button to select the SPECIAL menu. VIDEO AUDIO Language Key lock ISM Method TIME Low power 2. Press the button and then use D /E button to select Low power. SPECIAL 3. Press the button and then use D /E button to select On or Off. SCREEN • When you select On, the screen darkens. 4. Press the OK button to save. 20 Plasma Monitor TWIN Set ID Security OSD Rotate MENU Prev. On Off Operation Security PIP Operation 1. Press the MENU button and then use the 2. Press the button and then use the D /E D /E 3. Press the G button and then use the D /E button to select the SPECIAL menu. button to select Security. button to select On, Standby or Off. VIDEO AUDIO TIME SPECIAL • On: The security PIP operates when turning the monitor on. • Standby: The monitor switches on from standby mode, then the security PIP operates. • Off: The security PIP doesn’t work. SCREEN TWIN Language Key lock ISM Method Low power Set ID Security OSD Rotate On Standby Off MENU Prev. 4. Press the OK button to save. Menu Rotation for Vertical Vertical Viewing Viewing 1. Press the MENU button and then use the 2. Press the button and then use the D /E D /E button to select the SPECIAL menu. button to select OSD Rotate. 3. Press the G button and then use the D / E button to select Normal or Rotate. • Select Normal, if the monitor was installed horizontally. • Select Rotate, if the monitor was installed vertically. 4. Press the OK button to save. VIDEO AUDIO TIME SPECIAL Language Key lock ISM Method Low power Set ID Security OSD Rotate TWIN Normal Rotate SCREEN MENU Prev. Owner’s Manual 21 Operation Screen Menu Options Auto Adjustment RGB (PC) mode only; This function doesn’t work for RGB-DTV. Automatically adjusts picture position and minimizes image shaking. After adjustment, if the image is still not correct, your Monitor is functioning properly but needs further adjustment. The Auto config. and Manual config. are not active in DVI mode. 1. Press the MENU button and then use 2. Press the button and then use D /E D /E button to select the SCREEN menu. button to select Auto config.. VIDEO AUDIO TIME 3. Press the G button to run Auto configure. • When Auto config. has finished, OK will be shown on screen. • If the position of the image is still not correct, try Auto adjustment again. 4. In RGB (PC) mode, if the image needs to be adjusted more after using Auto config., you can make further adjustments with the Manual config. option. SPECIAL Auto config. ARC Zoom in/out Position Manual config. Screen adj. Reset XGA Mode SCREEN TWIN MENU Prev. Setting Picture Format - Caution: If a 4:3 fixed image is on the screen for a long time, it may remain visible. - Set every aspect ratio for RGB 480p, DVI 480p, Component 480i/480p, Video, and S-Video sources. - Use 4:3, or 16:9 for other input sources. 1. Press the ARC button repeatedly to select the desired picture format. You can also adjust ARC in the SCREEN menu. • 4:3 - Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both the left and right sides. • 16:9 - Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen. • Horizon - Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both sides, to create a spectacular view. • Zoom - Choose Zoom when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped. Picture Size Zoom - When enlarging or reducing the picture, the image may become distorted. 1. Use ZOOM+/ZOOM- button to enlarge or reduce the picture size. • Zoom adjustment range is 100~300. 2. Adjust the main picture position using the Zoom out 100% 22 Plasma Monitor D /E /F /G buttons while in enlarged picture mode. To set Operation Split Zoom Enlarges the picture in correct proportions. Split Zoom can be used for all input sources. In 2-Split Zoom mode, you can only move the image up or down. If a screen is enlarged, a screen can move without selecting section of screen Split Zoom. It’s not available to use this function if OSD Rotate is set to the Rotate option. 1. Press the SPLIT ZOOM button repeatedly to select either 2, 4 , or 9 Split Zoom. 9-Split zoom 4-Split zoom 2-Split zoom ▲ ▼ ▲ ▼ ◀▶ ◀▶ ▲ ▼ ◀▶ 2. Press the number button corresponding to the section you wish to enlarge. You can move within the enlarged image with the D / E / F / G button. To return to normal viewing, press the SPLIT ZOOM button again. Example of choosing 5. 9-Split zoom Section 5 is enlarged to fill the screen. ▲ ▼ ◀▶ Screen Position - This function works in the following mode: RGB-PC, RGB-DTV (480p,720p,1080i), COMPONENT (480p,720p,1080i). 1. Press the MENU button and then use D /E button to select the SCREEN menu. 2. Press the button and then use D /E 3. Press the button and then use D /E /F /G button to select Position. button to adjust the position. VIDEO AUDIO Auto config. ARC Zoom in/out TIME Position SPECIAL 4. Press the OK button to save. SCREEN TWIN ▲ ◀ ▶ ▼ Manual config. Screen adj. Reset XGA Mode MENU Prev. Manual Configure (RGB-PC mode only) - If the image still isn’t clear after auto adjustment and especially if characters are still jittery, adjust the picture Phase manually. - To correct the screen size, adjust Clock. 1. Press the MENU button and then use D /E 2. Press the G button and then use D /E button to select Manual config.. button to select the SCREEN menu. 3. Press the G button and then use D /E button to to select Phase or Clock. VIDEO 4. Use the F /G button to make appropriate adjustments. • The Phase adjustment range is 0 ~ 31. • The Clock adjustment range is -50 ~ +50. AUDIO TIME SPECIAL SCREEN TWIN Auto config. ARC Zoom in/out Position Manual config. Screen adj. Reset XGA Mode Phase Clock MENU Prev. 5. Press the OK button to save. Owner’s Manual 23 Operation Screen Menu Options continued Screen Adjustments (Video, (Video, S-Video S-Video and Component 480i mode only) - Use this function to correct jittering or picture instability while viewing a video tape. 1. Press the MENU button and then use D /E 2. Press the G button and then use D /E button to select Screen adj.. 3. Press the G button and then use D /E button to to select TV or VCR. button to select the SCREEN menu. • Select the VCR option if watching a VCR. • Select the TV option for other equipment.(Except VCR) 4. Press the OK button to save. VIDEO AUDIO TIME Auto config. ARC Zoom in/out Position Manual config. SPECIAL Screen adj. SCREEN Reset YNR TWIN TV VCR MENU Prev. Initializing (Reset to original factory value) - This function operates in every mode. - To initialize the adjusted value 1. Press the MENU button and then use D /E 2. Press the G button and then use button to select Reset. D /E button to select the SCREEN menu. VIDEO AUDIO TIME 3. Press the G button. SPECIAL • You can initialize Zoom In/Out, Manual config., Position, Split zoom, PIP size, PIP position and sub picture size for twin picture. SCREEN Auto config. ARC Zoom in/out Position Manual config. Screen adj. Reset To set XGA Mode TWIN MENU Prev. Selecting Wide Wide VGA/XGA mode (RGB-PC, DVI-PC mode only) - To see a normal picture, match the resolution of RGB XGA mode (1024x768, 1360x768, 1366x768) with the selection for XGA mode and the resolution of RGB VGA mode (640x480, 848x480, 852x480) with the selection for VGA mode in the SCREEN menu. - If the input source is RGB VGA mode, the screen menu option is changed from XGA mode to VGA mode automatically. 1. Press the MENU button and then use D /E 2. Press the G button and then use button to select VGA mode/XGA mode. D /E 3. Press the G button and then use D button to select the SCREEN menu. / E button to select the desired VGA/XGA resolution. VIDEO AUDIO TIME SPECIAL 4. Press the OK button to save. SCREEN Auto config. ARC Zoom in/out Position Manual config. Screen adj. Reset XGA Mode TWIN 1024x768 1360x768 1366x768 MENU Prev. Luminance Noise Reduction (Video, (Video, S-Video S-Video and Component 480i modes only) - Use YNR to reduce the picture noise which may appear on the screen. 1. Press the MENU button and then use 2. Press the button and then use 3. Press the G button and then use 4. Press the OK button to save. D /E D /E D /E button to select the SCREEN menu. button to select YNR. button to select On or Off. VIDEO AUDIO TIME SPECIAL SCREEN Auto config. ARC Zoom in/out Position Manual config. Screen adj. Reset YNR TWIN 24 Plasma Monitor MENU Prev. On Off Operation PIP (Picture-In-Picture) Feature - PIP lets you view 2 different inputs (sources) on your monitor screen at the same time. One source will be large, and the other source will show a smaller inset image. PIP Size Watching PIP Press the PIP button repeatedly to turn PIP on or off. Press the WIN.SIZE button and then use change the sub picture size. F / G button to Component Video 10 : 30 Win.size PIP Aspect Ratio Swapping the PIP Press the PIP ARC button. The sub picture appears as shown. Press the SWAP button to switch the main and sub pictures. Component Video 10 : 30 Video Component 10 : 30 16 : 9 4: 3 Main Picture Sub Picture Moving the PIP Press the WIN.POSITION button. Press the D / E / F / G button repeatedly until desired position is achieved. The sub picture moves up/down/left/right. Win.position ▲ ◀ ▶ ▼ Selecting an Input Signal Source for the PIP Use the SUB INPUT button to select the input source for the sub picture. Main Picture Source Video S-Video Component 480i Component 480p/720p/1080i RGB and DVI Available Sub Picture Sources S-Video, Component 480i/480p/720p/1080i, RGB, and DVI Video, Component 480i/480p/720p/1080i, RGB, and DVI Video,S-Video, RGB, and DVI Video and S-Video Component 480i, Video, and S-Video Owner’s Manual 25 Operation Twin Picture Setup Option - As the name suggests, this mode splits the screen into 2, allowing 2 picture sources to be shown on the monitor screen at the same time. Each source is given half the screen. Watching Twin Picture Press the TWIN PICTURE button repeatedly to select one of the Twin Picture options. DW 1 DW 2 Sub Picture Size Adjustment Press the WIN.SIZE button and then use F /G button to change the sub picture size. • Using the WIN.SIZE function in Twin Picture mode, main and sub picture sizes are changed simultaneously. Using the WIN.SIZE function in PIP mode, sub picture size is changed. • WIN.POSITION is not functional in Twin Picture mode. Swapping the Twin Picture Use the SWAP button to switch the main and sub pictures in twin picture mode. Component Video 10 : 30 Main Picture Video Component 10 : 30 Sub Picture Selecting a Source for the Twin Picture Use the SUB INPUT button to select the input source for the sub picture. Main Picture Source Video S-Video Component 480i Component 480p/720p/1080i RGB and DVI 26 Plasma Monitor Available Sub Picture Sources S-Video, Component 480i/480p/720p/1080i, RGB, and DVI Video, Component 480i/480p/720p/1080i, RGB, and DVI Video,S-Video, RGB, and DVI Video and S-Video Component 480i, Video, and S-Video Win.size ◀F G▶ External Control Device Setup External Control Device Setup - Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally. - Connect the serial port of the control device to the RS-232C jack on the Monitor back panel. - RS-232C connection cables are not supplied with the Monitor. ( )R( ) R AUDIO L ( )L ( ) EXTERNAL SPEAKER RS-232C INPUT (CONTROL/SERVICE) DVI INPUT RGB INPUT AUDIO INPUT RGB OUTPUT REMOTE CONTROL AUDIO INPUT PB PR COMPONENT INPUT R AUDIO L (MONO) ALARM S-VIDEO VIDEO INPUT AUDIO INPUT AC INPUT Type of Connector: D-Sub 9-pin Male No. Pin Name No Connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection RS-232C Configurations 3- Wire Configuration (Not standard) 7-Wire Configuration (Standard RS-232C cable) RXD TXD GND DTR DSR RTS CTS PC PDP D-Sub 9 D-Sub 9 TXD RXD GND DSR DTR CTS RTS RXD TXD GND DTR DSR RTS CTS PC PDP D-Sub 9 D-Sub 9 TXD RXD GND DTR DSR RTS CTS Owner’s Manual 27 External Control Device Setup Set ID - Use this function to specify a monitor ID number. - Refer to ‘Real Data Mapping 1’. See page 29. 1. Press the MENU button and then use the 2. Press the button and then use D /E 3. Press the G button and then use monitor ID number. F /G D /E button to select the SPECIAL menu. button to select Set ID. VIDEO AUDIO button to adjust Set ID to choose the desired TIME SPECIAL SCREEN • The adjustment range of Set ID is 1 ~ 99. TWIN Language Key lock ISM Method Low power Set ID Security OSD Rotate MENU Prev. Communication Parameters • Baud rate : 115200 bps (UART) • Data length : 8 bits • Parity : None • Stop bit : 1 bit • Communication code : ASCII code Command Reference List Transmission / Receiving Protocol COMMAND 1 COMMAND 2 DATA (Hexadecimal) 01. Power 02. Input Select 03. Aspect Ratio 04. Screen Mute 05. Volume Mute 06. Volume Control 07. Contrast 08. Brightness 09. Color 10. Tint 11. Sharpness 12. OSD Select 13. Remote Control Lock Mode 14. PIP/Twin 15. PIP Aspect Ratio 16. Split Zoom 17. PIP Position 18. Treble 19. Bass 20. Balance 21. Color Temperature 22. Red Adjustment 23. Green Adjustment 24. Blue Adjustment 25. PIP Input Source 26. Abnormal State 27. ISM Method 28. Low Power 29. Orbiter Time Setting 30. Orbiter Pixel Setting 31. Picture Size Setting for Twin Picture mode 32. Auto Configure 0~1 0~4 0~3 0~1 0~1 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0~1 0~1 0~3 0~1 21 ~99 0~3 0 ~ 64 0 ~ 64 0 ~ 64 0~3 0 ~ C8 0 ~ C8 0 ~ C8 0~4 0~a 0~3 0~1 1 ~ FE 0 ~9 0 ~64 • Menu doesn’t display on screen when setting the 4, 12, 13, and 26 ~ 32. 28 Plasma Monitor Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] * [Command 1]: k, j * [Command 2]: To control PDP set. * [Set ID]: You can adjust the set ID to choose desired monitor ID number in Special menu. Adjustment range is 1 ~ 99. When selecting Set ID ‘0’, every connected PDP set is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa decimal (0x0~0x63) on transmission/receiving protocol. * [DATA]: To transmit command data. Transmit ‘FF’ data to read status of command. * [Cr]: Carriage Return ASCII code ‘0x0D’ * [ ]: ASCII code ‘space (0x20)’ OK Acknowledgement [Command2][ ][Set ID][ ][OK][Data][x] * The Monitor transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer. Error Acknowledgement [Command2][ ][Set ID][ ][NG][x] * The Monitor transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions or communication errors. Data 1: Illegal Code 2: Not supported function 3: Wait more time External Control Device Setup 01. Power (Command2:a) 04. Screen Mute (Command2:d) G To control Power On/Off of the Monitor. G To select screen mute on/off. Transmission Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 0 : Power Off [k][d][ ][Set ID][ ][Data][Cr] 1 : Power On Acknowledgement Data 0 : Screen mute off (Picture on) 1 : Screen mute on (Picture off) [a][ ][Set ID][ ][OK][Data][x] Acknowledgement [d][ ][Set ID][ ][OK][Data][x] G To show Power On/Off. 05. Volume Mute (Command2:e) Transmission [k][a][ ][Set ID][ ][FF][Cr] Data 0 : Power Off 1 : Power On Acknowledgement [a][ ][Set ID][ ][OK][Data][x] G To control volume mute on/off. You can also adjust mute using the MUTE button on remote control. Transmission [k][e][ ][Set ID][ ][Data][Cr] * In a like manner, if other functions transmit ‘FF’ data based on this format, Acknowledgement data feedback presents status about each function. Data 0 : Volume mute on (Volume off) 1 : Volume mute off (Volume on) Acknowledgement [e][ ][Set ID][ ][OK][Data][x] 02. Input Select (Command2:b) (Main Picture Input) G To select input source for the Monitor. You can also select an input source using the INPUT SELECT button on the Monitor's remote control. Transmission [k][b][ ][Set ID][ ][Data][Cr] Data 0 : RGB 1 : Component 2 : Video 06. Volume Control (Command2:f) G To adjust volume. You can also adjust volume with the volume buttons on remote control. Transmission 3 : S-video 4 : DVI Acknowledgement [k][f][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping1’ as shown below. Acknowledgement [b][ ][Set ID][ ][OK][Data][x] [f][ ][Set ID][ ][OK][Data][x] 03. Aspect Ratio (Command2:c) (Main picture format) 07. Contrast (Command2:g) G To adjust the screen format. You can also adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Special menu. Transmission G To adjust screen contrast. You can also adjust contrast in the Video menu. [k][c][ ][Set ID][ ][Data][Cr] Data 0 Wide screen (16:9) Normal screen (4:3) Full screen (Zoom) Horizon Acknowledgement Transmission [k][g][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping1’ as shown below. Acknowledgement [g][ ][Set ID][ ][OK][Data][x] * Real data mapping 1 [c][ ][Set ID][ ][OK][Data][x] 0 : Step 0 * You select either 16:9 or 4:3 screen aspect ratio using the PC, DTV 720p/1080i. A : Step 10 (SET ID 10) F : Step 15 (SET ID 15) 10 : Step 16 (SET ID 16) 64 : Step 100 Owner’s Manual 29 External Control Device Setup 08. Brightness (Command2:h) 13. Remote Control Lock Mode (Command2:m) G To adjust screen brightness. You can also adjust brightness in the Video menu. G To lock the remote control and front panel controls on the monitor Transmission Transmission [k][h][ ][Set ID][ ][Data][Cr] [k][m][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping 1’. See page 29. Data 0: Lock off Acknowledgement [m][ ][Set ID][ ][OK][Data][x] [h][ ][Set ID][ ][OK][Data][x] • If you’re not using the remote control and front panel con- 1: Lock on Acknowledgement trols on the monitor, use this mode. When main power is on/off, remote control lock is released. 09. Color (Command2:i) G To adjust the screen color. You can also adjust color in the Video menu. Transmission [k][i][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping 1’. See page 29. Acknowledgement 14. PIP / Twin (Command2:n) G To control the PIP (Picture-in-Picture) or Twin Picture. You can also control the PIP/Twin picture mode using the PIP or TWIN PICTURE button on the remote control or in the Twin menu. Transmission [k][n][ ][Set ID][ ][Data][Cr] Data 0: PIP/DW off 1: PIP [i][ ][Set ID][ ][OK][Data][x] 2: DW1 3: DW2 Acknowledgement 10. Tint (Command2:j) [n][ ][Set ID][ ][OK][Data][x] G To adjust the screen tint. You can also adjust tint in the Video menu. 15. PIP Aspect Ratio (Command2:o) G To select the PIP picture format. You can also select the PIP picture format using PIP ARC on the remote control. Transmission [k][j][ ][Set ID][ ][Data][Cr] Data Red : 0 ~ Green : 64 • Refer to ‘Real data mapping 1’. See page 29. Transmission [k][o][ ][Set ID][ ][Data][Cr] Acknowledgement Data 0: 4:3 [j][ ][Set ID][ ][OK][Data][x] Acknowledgement 1: 16:9 [o][ ][Set ID][ ][OK][Data][x] 11. Sharpness (Command2:k) G To adjust the screen sharpness. You can also adjust sharpness in the Video menu. Transmission 16. Split Zoom (Command2:p) G To operate split zoom function and select the split zoom section number. Transmission [k][k][ ][Set ID][ ][Data][Cr] [k][p][ ][Set ID][ ][Data][Cr] Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping 1’. See page 29. Acknowledgement Data Min: 21 ~ Max: 99 • Refer to ‘Real data mapping 2’. [k][ ][Set ID][ ][OK][Data][x] Acknowledgement [p][ ][Set ID][ ][OK][Data][x] 12. OSD Select (Command2:l) G To select OSD (On Screen Display) on/off. Transmission [k][l][ ][Set ID][ ][Data][Cr] Data 0: OSD off Acknowledgement [l][ ][Set ID][ ][OK][Data][x] 1: OSD on * Real data mapping 2 21: 24: 41: 42: 44: 45: 91: Selection Selection Selection Selection Selection Selection Selection of of of of of of of split split split split split split split zoom zoom zoom zoom zoom zoom zoom 99: Selection 9 of 9 split zoom 30 Plasma Monitor External Control Device Setup 17. PIP Position (Command2:q) 21. Color Temperature (Command2:u) G To select sub picture position for PIP. You can also adjust the sub picture position using Win.position on the remote control or in the Twin menu. G To adjust color temperature. You can also adjust ACC in the Video menu. Transmission [k][q][ ][Set ID][ ][Data][Cr] Data 0: 1: 2: 3: Right down on screen Left down on screen Left up on screen Right up on screen Transmission [k][u][ ][Set ID][ ][Data][Cr] Data 0: Normal 1: Cool 2: Warm 3: User Acknowledgement [u][ ][Set ID][ ][OK][Data][x] Acknowledgement [q][ ][Set ID][ ][OK][Data][x] 22. Red Adjustment (Command2:v) G To adjust red in color temperature. Transmission 18. Treble (Command2:r) G To adjust treble. You can also adjust treble in the Audio menu. [k][v][ ][Set ID][ ][Data][Cr] Transmission Data Min: 0 ~ Max: C8 • Refer to ‘Real data mapping 3’ as shown below. Acknowledgement [k][r][ ][Set ID][ ][Data][Cr] [v][ ][Set ID][ ][OK][Data][x] Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping 1’. See page 29. Acknowledgement [r][ ][Set ID][ ][OK][Data][x] 23. Green Adjustment (Command2:w) G To adjust green in color temperature. Transmission [k][w][ ][Set ID][ ][Data][Cr] 19. Bass (Command2:s) G To adjust bass. You can also adjust bass in the Audio menu. Transmission Data Min: 0 ~ Max: C8 • Refer to ‘Real data mapping 3’ as shown below. Acknowledgement [w][ ][Set ID][ ][OK][Data][x] [k][s][ ][Set ID][ ][Data][Cr] Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping 1’. See page 29. Acknowledgement 24. Blue Adjustment (Command2:$) [s][ ][Set ID][ ][OK][Data][x] G To adjust blue in color temperature. Transmission [k][$][ ][Set ID][ ][Data][Cr] 20. Balance (Command2:t) G To adjust balance. You can also adjust balance in the Audio menu. Data Min: 0 ~ Max: C8 • Refer to ‘Real data mapping 3’ as shown below. Acknowledgement [$][ ][Set ID][ ][OK][Data][x] Transmission [k][t][ ][Set ID][ ][Data][Cr] * Real data mapping 3 Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping 1’. See page 29. Acknowledgement 0 : -20 5 : -19 A : -18 [t][ ][Set ID][ ][OK][Data][x] 5F: -1 64: 0 69: +1 C3: +19 C8: +20 Owner’s Manual 31 External Control Device Setup 25. PIP Input Select (Command2:y) 29. Orbiter Time Setting (Command2:r) G To select input source for sub picture in PIP mode. G To adjust orbiter operation time term. Transmission Transmission [k][y][ ][Set ID][ ][Data][Cr] [j][r][ ][Set ID][ ][Data][Cr] Data 0: RGB 2: Video 1: Component 3: S-video Data Min: 1 ~ Max: FE 4: DVI Acknowledgement Acknowledgement [r][ ][Set ID][ ][OK][Data][x] [y][ ][Set ID][ ][OK][Data][x] 26. Abnormal State (Command2:z) 30. Orbiter Pixel Setting (Command2:s) G To recognize an abnormal state. G To adjust pixel number in orbiter function. Transmission Transmission [k][z][ ][Set ID][ ][FF][Cr] [j][s][ ][Set ID][ ][Data][Cr] Data FF:Read Data Min: 0 ~ Max: 9 Acknowledgement Acknowledgement [z][ ][Set ID][ ][OK][Data][x] [s][ ][Set ID][ ][OK][Data][x] Data 0: Normal (Power on and signal exist) 1: No signal (Power on) 2: Turn the monitor off by remote control 3: Turn the monitor off by sleep time function 4: Turn the monitor off by RS-232C function 5: 5V down 6: AC down 7: Turn the monitor off by Fan Alarm function 8: Turn the monitor off by off time function 9: Turn the monitor off by auto off function a: Turn the monitor off by AV board detect 27. ISM Method (Command2:p) 31. Picture Size Setting for Twin Picture mode (Command2:t) G To adjust main picture size in twin picture mode. Transmission [j][t][ ][Set ID][ ][Data][Cr] Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping1’. See page 29. Acknowledgement [t][ ][Set ID][ ][OK][Data][x] G To avoid having a fixed image remain on screen. Transmission [j][p][ ][Set ID][ ][Data][Cr] Data 0: Normal 1: White wash 32. Auto Configure (Command2:u) 2: Orbiter 3: Inversion Acknowledgement G To adjust picture position and minimize image shaking automatically. Auto Configure only works in RGB-PC mode. [p][ ][Set ID][ ][OK][Data][x] Transmission [j][u][ ][Set ID][ ][Data][Cr] 28. Low Power (Command2:q) Data 1: To set G To control the low power function on/off. Acknowledgement Transmission [u][ ][Set ID][ ][OK][Data][x] [j][q][ ][Set ID][ ][Data][Cr] Data 0: Low power off 1: Low power on Acknowledgement [q][ ][Set ID][ ][OK][Data][x] 32 Plasma Monitor IR Code IR Code How to Connect G Connect your wired remote control to the Remote Control port on the Monitor. Remote Control IR Code G Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz TC Carrier frequency FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3 T1 G Configuration of frame • 1st frame Lead code Low custom code High custom code Data code Data code C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 • Repeat frame Repeat code Tf G Lead code 9 ms 4.5 ms 0.55 ms G Repeat code 9 ms 2.25 ms G Bit description • Bit “0” • Bit “1” 0.56 ms 0.56 ms 1.12 ms 2.24 ms G Frame interval : Tf The waveform is transmitted as long as a key is depressed. Tf Tf Tf=108ms @455KHz Owner’s Manual 33 IR Code Code (Hexa) 00H 01H 02H 03H 08H C4H C5H 09H 10H 11H 12H 13H 14H 15H 16H 17H 18H 19H 0BH D5H C6H 5AH D8H BFH 0EH 44H 43H 52H 4DH 60H 61H 63H 64H 6BH 40H 41H 69H 6AH 7BH 79H 76H 77H AFH 99H 34 Plasma Monitor Function UP (D) DOWN (E) VOL+ (G) VOL- (F) POWER On/Off POWER ON POWER OFF MUTE Number Key 0 Number Key 1 Number Key 2 Number Key 3 Number Key 4 Number Key 5 Number Key 6 Number Key 7 Number Key 8 Number Key 9 AII INPUT SELECT RGB DVI VIDEO S-VIDEO COMPONENT SLEEP OK (Á) MENU DASP APC PIP SUB INPUT SWAP PIP ARC TWIN PICTURE ZOOM + ZOOM Window Size Window Position Split Zoom ARC ARC (4:3) ARC (16:9) ARC (ZOOM) Auto configure Note R/C Button R/C Button R/C Button R/C Button R/C Button (Power On/Off) Discrete IR Code (Only Power On) Discrete IR Code (Only Power Off) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button (RGB/DVI/Video/S-video/Component) Discrete IR Code (Input RGB Selection) Discrete IR Code (Input DVI Selection) Discrete IR Code (Input Video Selection) Discrete IR Code (Input S-video Selection) Discrete IR Code (Input Component Selection) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button (PIP/TWIN Exchange) R/C Button (4:3/16:9) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button(4:3/16:9/Zoom Mode Selection) Discrete IR Code (Only 4:3 mode) Discrete IR Code (Only 16:9 mode) Discrete IR Code (Only ZOOM mode) Discrete IR Code (Only RGB-PC mode) Troubleshooting Checklist Troubleshooting Checklist • Check whether the Monitor is turned on. No picture & No sound • Power cord inserted into wall outlet? • Test the wall power outlet, plug other product’s power cord into the wall outlet where the Monitor’s power cord was plugged in. Picture OK & No sound • Press the VOLUME (G) button. • Sound muted? Press MUTE button. • Check to see if there is any object between the Plasma Display and the remote control causing obstruction. The remote control doesn’t work • Are batteries installed with correct polarity (+ to +, - to -)? (Refer to p.8) • Install new batteries. (Refer to p.8) Picture appears slowly after switching on • This is normal, the image is muted during the plasma display startup process. Please contact your service center, if the picture has not appeared after five minutes. • Select Color in the VIDEO menu and press the VOLUME (G) button. (Refer to p.16) No or Poor color or Poor picture • Keep a sufficient distance between the Monitor and the VCR. • Activate any function to restore the brightness of the picture. (If still picture is on the screen for more than 5 minutes, the screen gets dark.) Horizontal/vertical bars or picture shaking • Check for local interference such as an electrical appliance or power tool. No output from one of the speakers • Adjust Balance in the AUDIO menu. (Refer to p.17) Unusual sound from inside the monitor • A change in ambient humidity or temperature may result in an unusual noise when the plasma display is turned on or off and does not indicate a fault with the monitor. Owner’s Manual 35 Maintenance Maintenance - Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new Monitor. Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen 1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen. 2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your Monitor. Cleaning the Cabinet To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth. Extended Absence If you expect to leave your Monitor dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges. 36 Plasma Monitor Specification Product Specifications MODELS MU-50PZ90MQ Width (inches / mm) 48.2 / 1223 Height (inches / mm) 28.9 / 734 Depth (inches / mm) 4.1 / 105 Weight (pounds / kg) 95.2 / 43.2 Power requirement AC120V, 60Hz Resolution 1366 x 768 (Dot) Color 16,770,000 (256 steps of each R, G and B) Operating Temperature Range 32 ~ 104°F (0 ~ 40°C) Operating Humidity Range Less than 80% Maximum Elevation 6561 feet (2000m) • The specifications shown above may be changed without notice for quality improvement. Owner’s Manual 37 Notes Notes 38 Plasma Monitor Notes Notes Owner’s Manual 39 PLASMA MONITOR OWNER’S MANUAL MODEL : MU-50PZ90MQ Please read this owner’s manual thoroughly before operating the Monitor. Retain it for future reference. Record model number and serial number of the Monitor. See the label attached on the back of the Monitor and relate this information to your dealer if you ever require service. Model Number : Serial Number : P/NO : 3828VA0410H (RF03GB)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2003:10:08 12:55:51 Producer : Acrobat Distiller 4.0 for Macintosh Creator : QuarkXPressª3.3E: LaserWriter 8 Z1-8.7.1 Author : PSY Title : 410Hen(50PZ90MQ) Modify Date : 2003:10:08 13:00:37+09:00 Page Count : 40EXIF Metadata provided by EXIF.tools