LG Electronics USA RBHP-B213A Bluetooth Module User Manual SPECIFICATIONS FOR APPROVAL

LG Electronics USA Bluetooth Module SPECIFICATIONS FOR APPROVAL

User manual

CUSTOMER : LGE DATE : 2017.09.06. SPECIFICATIONS FOR APPROVAL PRODUCT NAME : BT(v4.2) + WLAN(802.11a/b/g/n/ac) 2.4G SISO/5G MIMO MODEL NAME : RBHP-B213A CUSTOMER P/N : EAT63433501 APPROVAL REMARK Designed Checked Approved LG Innotek Co., Ltd. DOCUMENT No. RBHP-B213A PAGE 68 APPENDIX (00)-0070 We only use Bluetooth.5G WLAN function is disabled by software.the module is to be installed in vehicle only
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (2 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released i Change History of Revision Revision Date Contents of Revision Change Remark 0.1 2015.4.23. Establishment 0.2 2015.9.15. Digital I/O Pins IN/OUT Range Spec. changed P.29 Pin configuration was modified P.52 Recommended Land Pattern updated P.59 0.3 2016.2.13. 2.4G WiFi power spec. updated P18 5G WiFi power spec. updated P22 0.4 2016.4.20. Model number is changed to RBHP-B213A(PCIe) PCIe power-on timing inserted P34 Pin configuration is modified(PCIe inserted) P51 0.5 2016.6.10 Application updated P4 Blockdiagram updated P58 Customer P/N inserted P1 0.6 2016.9.4 Block diagram updated P58 0.7 2016.10.14 Bluetooth, WiFi Radiation performance spec. inserted P12,13, 14, 17,18, 22 0.8 2016.10.26 Customer P/N modified P1 0.9 2017.01.06 ESD spec. modified P49 Antenna Tube color modified P6 1.0 2017.02.28 Module Radiation sensitivity spec. modified P9 BT/WiFi core0 5G Antenna tube color changed P6 1.1 2017.05.17 Label information updated P5 1.2 2017.05.23 Out box label information updated P63 a b c d e f g h j k l m n o p q
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (3 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released Change History of Revision Revision Date Contents of Revision Change Remark 1.3 2017.6.27. PCIE power-on timing updated P35 PCIE I/O characteristics updated P50 RF performance guarantee min. VBAT voltage updated P53 Application schematic updated P63 1.4 2017.7.17. Bluetooth version updated P1 1.5 2017.8.10. Low temp. operating comment added in Clause 5. (Customer Request) P5 1.6 2017.9.06. Reliability spec. updated P58 r s t u v w x
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (4 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released Table of Contents 1. Application 2. Quality 3. Appearance and Characteristics 4. Application of Bluetooth Module 5. Maximum Rating 6. Test 7. Labeling Information 8. Mechanical Dimension 9. General Features 10. Electrical Specification 11. Pin Configuration 12. Reliability Test 13. Block Diagram 14. Reference Circuit 15. Reflow Profile 16. Recommended Land Pattern 17. Packing Information 18. Ordering Information
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (5 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 1. Application This specification is applied to LGInnotek Bluetooth (v4.2)and 2.4GHz SISO/5GHz MIMO WLAN(802.11a/b/g/n/ac) Module RBHP-B213A which includes BCM88359 2. Quality Quality should meet each condition which mentioned on this specification. However, the items which are not mentioned on this specification follow the inspection agreements and standards which are agreed with both companies. 3. Appearance and Characteristics 1) Appearance Appearance should not be contaminated by harmful materials and should not have cracks etc. Mechanical dimensions should meet the contents of clause 8. 2) Characteristics Electrical characteristics should meet the contents of clause 10. 4. Application of Bluetooth v4.2 and 2.4GHz/5GHz WLAN(IEEE 802.11.a/b/g/n/ac) 1) Automotive 5. Maximum Rating NO ITEM Rating UNIT 1 Operating Temperature Range -40 ~ +85 ℃ 2 Storage Temperature Range -40 ~ +105 ℃ 3 VBAT Voltage Range -0.5 ~ 6.0 V 4 VIO Voltage Range -0.5 ~ 3.9 V 5 VBAT Max. Current 700(@3.3V) mA 6 VIO Max. Current 50(@1.8V) mA v ■ RBHP-B213A Module assures operating normally at -40 ~ +85℃. w
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (6 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released EAT63433501 6. Test Electrical characteristics are tested for every products. However, if there are any objection in judgments, it should be treated with agreements of companies. 7. Labeling Information No. Index ① PRODUCT ② MODEL PART NO. ③ MANUFACTURED YEAR (0~9) ④ MANUFACTURED MONTH(1,2, …9, A,B,C) ⑤ GwangJu ⑥ MANUFACTURED DATE (1~31) ⑦ MANUFACTURED SERIAL NUMBER(0001~9999) ⑧ Customer P/N ⑨ QR CODE INFORMATION : EAT63433501_704GJ270059 ② ④ ⑤ ① ③ ⑥ ⑧ RBHP-B213A GWANGGAETOH 7 04 GJ 27 0059 ⑦ p ⑨
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (7 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 8. Mechanical Dimension 1) Dimension without Antenna Ass’y [Unit: mm]
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (8 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 8. Mechanical Dimension 2) Dimension with Antenna Ass’y [Unit: mm]
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (9 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 9. General Features 1) Features • Operation Voltage is 3.3V/1.8V Dual Power Rail • WiFi Single-stream up to 866 Mbps data rate • Automotive Module : All components are AEC-Q 100/200 qualified • Support 2 Antenna port : ANT0 : Bluetooth/5G WLAN, ANT1 : 2.4G/5G WLAN • Integrated WLAN PA, RF Switch and LNA • RoHS Compliant • Size : 35.3 x 35.3 x 7.8 mm3 • Support bandwidth : HT20 / HT40 / VHT80 • HOST Interface : PCIE/SDIO(WLAN), UART(BT), PCM(I2S) • Package type : Connector type(B to B) 9.1 BT(v4.2) + 2.4GHz/5GHz WLAN(IEEE 802.11a/b/g/n/ac) 2.4G SISO/5G MIMO
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (10 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 9. General Features 1) Bluetooth Key Features • Supports key features of upcoming Bluetooth standards • Fully supports Bluetooth Core Specification version 4.2 + (Enhanced Data Rate) EDR features: -. Adaptive Frequency Hopping (AFH) -. Quality of Service (QoS) -. Extended Synchronous Connections (eSCO) – Voice Connections -. Fast Connect (interlaced page and inquiry scans) -. Secure simple Pairing (SSP) -. Sniff Sub rating (SSR) -. Encryption Pause Resume (EPR) -. Extended Inquiry Response (EIR) -. Link Supervision Timeout (LST) • UART baud rates up to 4 Mbps • Supports all Bluetooth 4.2 packet types • Supports maximum Bluetooth data rates over HCI UART • Multipoint operation with up to seven active slaves -. Maximum of seven simultaneous active ACL links -. Maximum of three simultaneous active SCO and eSCO connections with scatternet support • Narrowband and wideband packet loss concealment • Scatternet operation with up to four active piconets with background scan and support for scatter mode • High-speed HCI UART transport support • Channel quality driven data rate and packet type selection • Standard Bluetooth test modes • Extended radio and production test mode features • Full support for power savings modes -. Bluetooth clock request -. Bluetooth standard sniff -. Deep-sleep modes and software regulator shutdown 9.2 Bluetooth(BT v4.2+EDR compliant)
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (11 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 9. General Features 1) WLAN RF band & modulation Features • Dual-band 2.4GHz and 5GHz 802.11 a/b/g/n/ac(802.11ac compliant) • Up to 866Mbps data rate • Supports 20, 40 and 80MHz channels with optional SGI(256 QAM modulation) • Tx and Rx low-density parity check(LDPC) • Supports IEEE 802.11ac/n beamforming • Supports PCIe v3.0-compliant interface running at GEN1 speeds • Supports two antennas with Bluetooth/5G WLAN and 2.4G/5G WLAN antenna • Supports standard SDIO V3.0 (up to SDR104 mode at 208MHz, 4-bit and 1-bit) • Backward compatibility with SDIO v2.0 host interface • WPA and WPA2(Personal) support for powerful encryption and authentication • AES and TKIP in hardware for faster data encryption and IEEE 802.11i compatibility • Reference WLAN subsystem provides Wi-Fi protected Setup(WPS) 2) WLAN MAC features • Enhanced MAC for supporting IEEE 802.11ac features • Transmission and reception of aggregated MPDUs(A-MPDU) for high throughput(HT) • Support for power management schemes, including WMM power-save multi-poll(PSMP) and multiphase PSMP operation • Support for immediate ACK and block-ACK policies • Inter-frame space timing support, including RIFS • Back-off counters in hardware for supporting multiple priorities as specified in the WMM specification • Timing synchronization function(TSF), network allocation vector(NAV) maintenance, and target beacon transmission time(TBTT) generation in hardware • Hardware offload for AES-CCMP, legacy WPA TKIP, legacy WEP ciphers, WAPI, and support for key management • Programmable independent basic service set(IBSS) or infrastructure basic service set functionality 9.3 WLAN
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (12 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 3) WLAN PHY features • Programmable data rates from MCS0-9 in 20MHz, 40MHz, and 80MHz channels, as specified in IEEE 802.11ac • Improved performance with channel smoothing and spur canceller support • Supports Optional short GI and Green field modes in Tx and Rx • Tx and Rx LDPC for improved range and power efficiency • Beamforming support • Supports IEEE 802.11h/k for worldwide operation • Advanced algorithms for low power, enhanced sensitivity, range, and reliability • IEEE 802.11a, 11b, 11g, 11n, 11ac single stream PHY standards • Designed to meet FCC and other worldwide regulatory requirements 9. General Features 9.3 WLAN 9.4 JEDEC MSL (Moisture Sensitivity Level) Test • MSL 3 Level (Floor Life Time : 168Hrs. / Condition : ≤30℃, 60% RH) • Standard : IPC / JEDEC J-STD-020C Bake Soak Reflow 24Hrs. / 125℃ 40Hrs. / 60℃, 60% RH 3 times / 240℃
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (13 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 1) Basic Data Rate - Rx Performance General Performance Parameter Condition Min Typ Max Unit Frequency Range 2402 2480 MHz Impedance BT_ANT Pin - 50 - Ohm Receiver Performance Parameter Condition Min Typ Max Unit Sensitivity level (BER≤0.1%) (Radiation performance) Single slot - - -84 (-75) dBm Sensitivity level (BER≤0.1%) (Radiation performance) Multi slot - - -84 (-75) dBm C/I performance1) (BER≤0.1%) C/I co-channel , Input=-60dBm - - 11 dB C/I 1MHz , Input=-60dBm - - 0 dB C/I 2MHz , Input=-60dBm - - -20 dB C/I ≥3MHz , Input=-67dBm - - -40 dB Image radio , Input=-67dBm - - -9 dB Image±1 , Input=-67dBm - - -20 dB Out-of-band Blocking2) (BER≤0.1%) 30MHz ~ 2000MHz -10 - - dBm 2000MHz ~ 2400MHz -27 - - dBm 2500MHz ~ 3000MHz -27 - - dBm 3000MHz ~ 12.75GHz -10 - - dBm Intermodulation (BER≤0.1%) Input=-64dBm, n=5 -39 - - dBm Maximum Input Level (BER≤0.1%) -20 - - dBm 10.1 Bluetooth k
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (14 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 2) Basic Data Rate - Tx Performance Transmitter Performance Parameter Condition Min Typ Max Unit Transmit Power (Radiation performance) All temperature -6 (-8) 2 4 (6) dBm Power density All temperature - - 20 dBm Frequency Range All temperature 2402 - 2480 MHz 20dB bandwidth All temperature - - 1000 KHz Adjacent channel power3) ±2MHz - - -20 dBm ±3MHz - - -40 dBm ±4MHz - - -40 dBm Out-band Spurious Emission 30MHz ~ 1GHz - - -36 dBm 1GHz ~ 12.75GHz - - -30 dBm 1.8GHz ~ 1.9GHz - - -47 dBm 5.1GHz ~ 5.3GHz - - -47 dBm Modulation Characteristics ΔF1avg 140 - 175 KHz ΔF2max 115 - - KHz ΔF2avg/ΔF1avg 80 - - % Initial Carrier Frequency Tolerance DH1 packet -75 - 75 KHz Carrier Frequency Drift Five slot packet(DH5) -40 - 40 KHz 10. Electrical Specification 10.1 Bluetooth k
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (15 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 3) Enhanced Data Rate - Rx Performance Enhanced Data Rate Receiver Performance Parameter Condition Min Typ Max Unit Sensitivity at 0.01% BER (Radiation performance) π/4 DQPSK/8DPSK - - -80 (-75) dBm Maximum received signal at 0.1% BER π/4 DQPSK -20 - - dBm 8DPSK -20 - - dBm C/I co-channel at 0.1% BER π/4 DQPSK - - 13 dB 8DPSK - - 21 dB Adjacent channel selectivity C/I F=F0+1MHz π/4 DQPSK - - 0 dB 8DPSK - - 5 dB Adjacent channel selectivity C/I F=F0-1MHz π/4 DQPSK - - 0 dB 8DPSK - - 5 dB Adjacent channel selectivity C/I F=F0+2MHz π/4 DQPSK - - -30 dB 8DPSK - - -25 dB Adjacent channel selectivity C/I F=F0-2MHz π/4 DQPSK - - -20 dB 8DPSK - - -13 dB Adjacent channel selectivity C/I F≥F0+3MHz π/4 DQPSK - - -40 dB 8DPSK - - -33 dB Adjacent channel selectivity C/I F≤F0-5MHz π/4 DQPSK - - -40 dB 8DPSK - - -33 dB Adjacent channel selectivity C/I F=Fimage π/4 DQPSK - - -7 dB 8DPSK - - 0 dB 10. Electrical Specification 10.1 Bluetooth k
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (16 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released Enhanced Data Rate Transmitter Performance Parameter Condition Min Typ Max Unit Relative transmit power. -4 -1 1 dB π/4 DQPSK max carrier frequency stability |ωo| -10 - 10 kHz π/4 DQPSK max carrier frequency stability |ωi| -75 - 75 kHz π/4 DQPSK max carrier frequency stability |ωo+ωi | -75 - 75 kHz 8 DPSK max carrier frequency stability |ωo| -10 - 10 kHz 8 DPSK max carrier frequency stability |ωi| -75 - 75 kHz 8 DPSK max carrier frequency stability |ωo+ωi | -75 - 75 kHz π/4 DQPSK Modulation Accuracy RMS DEVM - - 20 % 99% DEVM - - 30 % Peak DEVM - - 35 % 8 DPSK Modulation Accuracy RMS DEVM - - 13 % 99% DEVM - - 20 % Peak DEVM - - 25 % In-Band spurious emissions F＞F0+3MHz - - -40 dBm F＜F0-3MHz - - -40 dBm F=F0-3MHz - - -40 dBm F=F0-2MHz - - -20 dBm F=F0-1MHz - - -26 dBm F=F0+1MHz - - -26 dBm F=F0+2MHz - - -20 dBm F=F0+3MHz - - -40 dBm EDR Differential Phase Encoding (No error) 99 - - % 4) Enhanced Data Rate - Tx Performance 10. Electrical Specification 10.1 Bluetooth
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (17 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 5) BLE Performance 10. Electrical Specification 10.1 Bluetooth General Performance Parameter Condition Min Typ Max Unit Frequency Range 2402 2480 MHz Impedance BT_ANT Pin - 50 - Ohm Sensitivity level (BER≤0.1%) (Radiation performance) GFSK(1Mbps) - - -87 (-75) dBm Transmit Power - -6 (-8) 2 4 (6) dBm Modulation Characteristics ΔF1avg 225 - 275 KHz ΔF2avg 230 - - KHz ΔF2avg/ΔF1avg 80 - - % J
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (18 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released General Performance Parameter Condition Min Typ Max Unit Frequency Range 2.4G WiFi 2400 2500 MHz 5G WiFi 4900 5845 MHz Impedance WLAN_ANT Pin - 50 - Ohm 10. Electrical Specification 1) 2.4GHz DSSS and HR/DSSS (CCK) Transmitter -. IEEE 802.11b DSSS and HR/DSSS modulation Transmitter Performance Parameter Condition Min Typ Max Unit RMS Transmit power (Radiation performance) 11Mbps CCK 13 (8) 16 19 (24) dBm RMS EVM 11Mbps CCK - - 35 % Spectral mask, 1st Sidelobe 11Mbps CCK (fc±11MHz) - - -30 dBr Spectral mask, 2nd Sidelobe 11Mbps CCK (fc±22MHz) - - -50 dBr RF Carrier suppression Normal/Extreme 15 - - dBc Spurious emissions 30MHz ~ 1GHz ( RBW=100kHZ) - - -62 dBm 1GHz ~ 12.75GHz (RBW=1MHz) - - -47 dBm 1.8GHz ~ 1.9GHz (RBW=1MHz) - - -53 dBm 5.15GMHz ~ 5.3GHz (RBW=1MHz) - - -53 dBm 10.2 WLAN k
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (19 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released Transmitter Performance Parameter Condition Min Typ. Max Unit RMS Transmit power (Radiation performance) OFDM, 64-QAM(3/4) 9 (4) 12 15 (20) dBm OFDM, 64-QAM(5/6) 9 (4) 12 15 (20) dBm RMS EVM OFDM, 64-QAM(3/4) - - -25 dB OFDM, 64-QAM(5/6) - - -27 dB Spectral mask OFDM, 64-QAM(3/4) (fc±11MHz) - - -20 dBr OFDM, 64-QAM(3/4) (fc±20MHz) - - -28 dBr OFDM, 64-QAM(3/4) (fc±30MHz) - - -40 dBr OFDM, 64-QAM(5/6) (fc±11MHz) HT20 - - -20 dBr OFDM, 64-QAM(5/6) (fc±20MHz) HT20 - - -28 dBr OFDM, 64-QAM(5/6) (fc±30MHz) HT20 - - -45 dBr Center frequency leakage Normal/Extreme - - -15 dB Spurious emissions 30MHz ~ 1GHz ( RBW=100kHZ) - - -62 dBm 1GHz ~ 12.75GHz (RBW=1MHz) - - -47 dBm 1.8GHz ~ 1.9GHz (RBW=1MHz) - - -53 dBm 5.15GMHz ~ 5.3GHz (RBW=1MHz) - - -53 dBm 10. Electrical Specification 2) 2.4GHz OFDM Transmitter -. IEEE 802.11g and IEEE 802.11n(HT 20/40 modes MCS0 to MCS7) OFDM modulation 10.2 WLAN d k
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (20 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 3) 2.4GHz DSSS and HR/DSSS (CCK) Receiver -. IEEE 802.11b DSSS and HR/DSSS modulation Receiver Performance Parameter Condition Min Typ Max Unit Rx sensitivity (Radiation performance) 1Mbps DSSS1) - - -89(-81) dBm 2Mbps DSSS1) - - -84(-76) dBm 5.5Mbps CCK1) - - -80(-72) dBm 11Mbps CCK1) - - -76(-68) dBm Maximum input level DSSS1) -10 - - dBm CCK1) -10 - - dBm Adjacent channel rejection DSSS2) - - 35 dBr CCK2) - - 35 dBr 1) 1024-byte packets, 8% PER 2) 1024-byte packets, 8% PER, 25MHz channel separation. 10.2 WLAN n
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (21 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 4) 2.4GHz OFDM Receiver -. IEEE 802.11g and IEEE 802.11n (HT 20/40 modes MCS0 to MCS7 800ns Guard Interval non-STBC) OFDM modulation 10.2 WLAN Receiver Performance Parameter Condition Min Typ Max Unit Maximum input level3) (Radiation performance) Normal/Extreme -20 - - dBm Rx sensitivity (Radiation performance) (IEEE 802.11g) 6Mbps1) - - -82(-74) dBm 9Mbps1) - - -81(-73) dBm 12Mbps1) - - -79(-71) dBm 18Mbps1) - - -77(-69) dBm 24Mbps1) - - -74(-68) dBm 36Mbps1) - - -70(-62) dBm 48Mbps1) - - -66(-58) dBm 54Mbps1) - - -65(-57) dBm Rx sensitivity (Radiation performance) (IEEE 802.11n) MCS02) (HT 20) - - -82(-74) dBm MCS12) (HT 20) - - -79(-71) dBm MCS22) (HT 20) - - -77(-69) dBm MCS32) (HT 20) - - -74(-68) dBm MCS42) (HT 20) - - -70(-62) dBm MCS52) (HT 20) - - -66(-58) dBm MCS62) (HT 20) - - -65(-57) dBm MCS72) (HT 20) - - -64(-56) dBm 1) 1024-byte packets, 10% PER. 2) 4096-byte packets, 10% PER. Applies to both HT-mixed(HT_MF) and HT-greenfield(HT-GF) format packet preamble types. 3) 1024-byte packets OFDM or 4096-byte HT packets, 10% PER. 4) 1024-byte packets, 10% PER, 25MHz channel separation. 5) 4096-byte packets, 10% PER, 25MHz channel separation.
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (22 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.2 WLAN Adjacent channel rejection (IEEE 802.11g) 6Mbps4) 16 - - dB 9Mbps4) 15 - - dB 12Mbps4) 13 - - dB 18Mbps4) 11 - - dB 24Mbps4) 8 - - dB 36Mbps4) 4 - - dB 48Mbps4) 0 - - dB 54Mbps4) -1 - - dB Adjacent channel rejection (IEEE 802.11n) MCS05) 16 - - dB MCS15) 13 - - dB MCS25) 11 - - dB MCS35) 8 - - dB MCS45) 4 - - dB MCS55) 0 - - dB MCS65) -1 - - dB MCS75) -2 - - dB Receiver Performance Parameter Condition Min Typ Max Unit
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (23 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released Transmitter Performance Parameter Condition Min Typ Max Unit RMS Transmit power (Radiation performance) OFDM, 64-QAM(3/4)/(5/6) 9 (4) 12 15 (20) dBm OFDM, 256-QAM(3/4)/(5/6) 5 (0) 8 11 (16) dBm RMS EVM OFDM, 64-QAM(3/4) - - -25 dB OFDM, 64-QAM(5/6) - - -27 dB OFDM, 256-QAM(3/4) - - -30 dB OFDM, 256-QAM(5/6) - - -32 dB 10. Electrical Specification 5) 5GHz OFDM Transmitter -. IEEE 802.11a, IEEE 802.11n (HT 20/40 modes MCS0 to MCS7) and IEEE 802.11ac OFDM modulation((VHT 20/40, VHT80 modes MCS0 to MCS9) 10.2 WLAN Spectral mask OFDM, 64-QAM(3/4) (fc±11MHz) - - -20 dBr OFDM, 64-QAM(3/4) (fc±20MHz) - - -28 dBr OFDM, 64-QAM(3/4) (fc±30MHz) - - -40 dBr OFDM, 64-QAM(5/6) (fc±11MHz) HT20 - - -20 dBr OFDM, 64-QAM(5/6) (fc±20MHz) HT20 - - -28 dBr OFDM, 64-QAM(5/6) (fc±30MHz) HT20 - - -45 dBr OFDM, 64-QAM(5/6) (fc±21MHz) HT40 - - -20 dBr OFDM, 64-QAM(5/6) (fc±40MHz) HT40 - - -28 dBr OFDM, 64-QAM(5/6) (fc±60MHz) HT40 - - -45 dBr OFDM, 256-QAM(5/6) (fc±11MHz) VHT20 - - -20 dBr OFDM, 256-QAM(5/6) (fc±20MHz) VHT20 - - -28 dBr OFDM, 256-QAM(5/6) (fc±30MHz) VHT20 - - -40 dBr e k
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (24 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.2 WLAN Transmitter Performance Parameter Condition Min Typ Max Unit Spectral mask OFDM, 256-QAM(5/6) (fc±21MHz) VHT40 - - -20 dBr OFDM, 256-QAM(5/6) (fc±40MHz) VHT40 - - -28 dBr OFDM, 256-QAM(5/6) (fc±60MHz) VHT40 - - -40 dBr OFDM, 256-QAM(5/6) (fc±41MHz) VHT80 - - -20 dBr OFDM, 256-QAM(5/6) (fc±80MHz) VHT80 - - -28 dBr OFDM, 256-QAM(5/6) (fc±120MHz) VHT80 - - -40 dBr Center frequency leakage Normal/Extreme - - -15 dB Spurious emissions 30MHz ~ 1GHz ( RBW=100kHZ) - - -62 dBm 1GHz ~ 12.75GHz (RBW=1MHz) - - -47 dBm 1.8GHz ~ 1.9GHz (RBW=1MHz) - - -53 dBm 5.15GMHz ~ 5.3GHz (RBW=1MHz) - - -53 dBm
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (25 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 1) 1024-byte packets, 10% PER. 2) 4096-byte packets, 10% PER. Applies to both HT-mixed(HT_MF) and HT-greenfield(HT-GF) format packet preamble types. 3) 1024-byte packets OFDM or 4096-byte HT packets, 10% PER. 4) 1024-byte packets, 10% PER, 25MHz channel separation. 5) 4096-byte packets, 10% PER, 25MHz channel separation. 10.2 WLAN 5) 5GHz OFDM Receiver -. IEEE 802.11a, IEEE 802.11n (HT 20/40 modes MCS0 to MCS7) and IEEE 802.11ac OFDM modulation((HT 20/40, VHT80 modes MCS0 to MCS9) Receiver Performance Parameter Condition Min Typ Max Unit Maximum input level3) (Radiation performance) Normal/Extreme -30 - - dBm Rx sensitivity (Radiation performance) (IEEE 802.11a) 6Mbps1) - - -82(-74) dBm 9Mbps1) - - -81(-73) dBm 12Mbps1) - - -79(-71) dBm 18Mbps1) - - -77(-69) dBm 24Mbps1) - - -74(-68) dBm 36Mbps1) - - -70(-62) dBm 48Mbps1) - - -66(-58) dBm 54Mbps1) - - -65(-57) dBm Rx sensitivity (Radiation performance) (IEEE 802.11n) MCS02) (HT 20) - - -82(-74) dBm MCS12) (HT 20) - - -79(-71) dBm MCS22) (HT 20) - - -77(-69) dBm MCS32) (HT 20) - - -74(-68) dBm MCS42) (HT 20) - - -70(-62) dBm MCS52) (HT 20) - - -66(-58) dBm MCS62) (HT 20) - - -65(-57) dBm MCS72) (HT 20) - - -64(-56) dBm
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (26 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.2 WLAN Receiver Performance Parameter Condition Min Typ Max Unit Rx sensitivity (IEEE 802.11n) MCS02) (HT 40) - - -79(-71) dBm MCS12) (HT 40) - - -76(-68) dBm MCS22) (HT 40) - - -74(-66) dBm MCS32) (HT 40) - - -71(-63) dBm MCS42) (HT 40) - - -69(-61) dBm MCS52) (HT 40) - - -63(-55) dBm MCS62) (HT 40) - - -62(-54) dBm MCS72) (HT 40) - - -61(-53) dBm Rx sensitivity (IEEE 802.11ac) MCS02) (VHT 20) - - -82(-74) dBm MCS12) (VHT 20) - - -79(-71) dBm MCS22) (VHT 20) - - -77(-69) dBm MCS32) (VHT 20) - - -74(-66) dBm MCS42) (VHT 20) - - -70(-62) dBm MCS52) (VHT 20) - - -66(-58) dBm MCS62) (VHT 20) - - -65(-57) dBm MCS72) (VHT 20) - - -64(-56) dBm MCS82) (VHT 20) - - -59(-51) dBm MCS92) (VHT 20) - - -57(-49) dBm
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (27 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.2 WLAN Receiver Performance Parameter Condition Min Typ Max Unit Rx sensitivity (IEEE 802.11ac) MCS02) (VHT 40) - - -79(-71) dBm MCS12) (VHT 40) - - -76(-68) dBm MCS22) (VHT 40) - - -74(-66) dBm MCS32) (VHT 40) - - -71(-63) dBm MCS42) (VHT 40) - - -67(-59) dBm MCS52) (VHT 40) - - -63(-55) dBm MCS62) (VHT 40) - - -62(-54) dBm MCS72) (VHT 40) - - -61(-53) dBm MCS82) (VHT 40) - - -56(-48) dBm MCS92) (VHT 40) - - -53(-45) dBm Rx sensitivity (IEEE 802.11ac) MCS02) (VHT 80) - - -76(-68) dBm MCS12) (VHT 80) - - -73(-65) dBm MCS22) (VHT 80) - - -71(-63) dBm MCS32) (VHT 80) - - -68(-60) dBm MCS42) (VHT 80) - - -64(-56) dBm MCS52) (VHT 80) - - -60(-52) dBm MCS62) (VHT 80) - - -59(-51) dBm MCS72) (VHT 80) - - -58(-50) dBm MCS82) (VHT 80) - - -53(-45) dBm MCS92) (VHT 80) - - -51(-43) dBm
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (28 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.2 WLAN Receiver Performance Parameter Condition Min Typ Max Unit Adjacent channel rejection (IEEE 802.11a) 6Mbps4) 16 - - dB 9Mbps4) 15 - - dB 12Mbps4) 13 - - dB 18Mbps4) 11 - - dB 24Mbps4) 8 - - dB 36Mbps4) 4 - - dB 48Mbps4) 0 - - dB 54Mbps4) -1 - - dB Adjacent channel rejection (IEEE 802.11n) MCS05) 16 - - dB MCS15) 13 - - dB MCS25) 11 - - dB MCS35) 8 - - dB MCS45) 4 - - dB MCS55) 0 - - dB MCS65) -1 - - dB MCS75) -2 - - dB
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (29 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.2 WLAN Receiver Performance Parameter Condition Min Typ Max Unit Adjacent channel rejection (IEEE 802.11ac) MCS05) 16 - - dB MCS15) 13 - - dB MCS25) 11 - - dB MCS35) 8 - - dB MCS45) 4 - - dB MCS55) 0 - - dB MCS65) -1 - - dB MCS75) -2 - - dB MCS85) -7 - - dB MCS95) -9 - - dB
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (30 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released Item Symbol Min Typ Max Unit Input high voltage VIH 1.27 - - V Input low voltage VIL - - 0.58 V Output high voltage@2mA VOH 1.40 - - V Output low voltage@2mA VOL - - 0.45 V 1) SDIO Interface I/O pins and PCIe out of band signals(PERST_N/PME_L/CLKREQ_N) 10. Electrical Specification 10.3 I/O characteristics *VIO_SD= 1.8V Item Symbol Min Typ Max Unit Input high voltage VIH 0.625xVIO - - V Input low voltage VIL - - 0.25xVIO V Output high voltage@2mA VOH 0.75xVIO - - V Output low voltage@2mA VOL - - 1.25xVIO V *VIO_SD = 3.3V 2) Other Digital I/O Pins(UART/PCM/WAKE/REG_ON/STRAP and GPIOs) *VIO = 1.8V Item Symbol Min Typ Max Unit Input high voltage VIH 0.625xVIO - VIO+0.1 V Input low voltage VIL - - 0.35xVIO V Output high voltage@2mA VOH 0.45xVIO - - V Output low voltage@2mA VOL - - 0.45 V
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (31 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics 4) Sequencing of reset and regulator control signals - Description of control signals *WL_REG_ON : Used by the PMU to power up the WLAN section. It is also OR-gated with the BT_REG_ON input to control the internal BCM88359 regulators. When this pin is high, the regulators are enabled and the WLAN section is out of reset. When this pin is low, the WLAN section is in reset. If both the BT_REG_ON and WL_REG_ON pins are low, the regulators are disabled *BT_REG_ON : Used by the PMU(OR-gated with the WL_REG_ON)to power up the internal BCM88359 regulators. If both the BT_REG_ON and WL_REG_ON pins are low, the regulators are disabled. When this pin is low and WL_REG_ON is high, the BT section is in reset 3) WLAN host interface strap selection *VIO = 3.3V Item Symbol Min Typ Max Unit Input high voltage VIH 2.00 - VIO+0.1 V Input low voltage VIL - - 0.8 V Output high voltage@2mA VOH VIO-0.4 - - V Output low voltage@2mA VOL - - 0.4 V PCIE_EN Mode High PCIe SDIO_DIS High Low 1.8V SDIO Low Low 3.3V SDIO - PCIE_EN, SDIO_DIS, SDIO_PAD SDIO_PAD Low High High low
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (32 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics - Control signal timing diagrams *WLAN =ON, Bluetooth = ON *WLAN =OFF, Bluetooth = OFF
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (33 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification - Control signal timing diagrams *WLAN =ON, Bluetooth = OFF *WLAN =OFF, Bluetooth = ON 10.3 I/O characteristics
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (34 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics - Boot-Up Sequence and Reset timing VBAT WL_REG_ON /BT_REG_ON VDDC (on-chip PMU) Internal POR (Power on Reset) Internal Reference Clock < 950us 3.3V 8ms Boot ROM execution starts and firmware download begins (UART and SDIO command start) < 104ms < 4ms After a fixed delay following internal POR and REG_ON going high, Module responds to host(address0x14) reads VIO <0ms <70us 27ns <200ms <200ms
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (35 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics - PCIe Power-on Timing *Timing Parameter WL_REG_ON)Perst# Deassertion – First Config Access) r
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (36 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics 5) UART characteristics -. UART physical interface is a standard, 4-wire interface(Rx, Tx, RTS, CTS) with adjustable baud rates from 9600 bps to 4Mbps. Normally the UART baud rate is set by a configuration record downloaded after reset or by automatic baud rate detection. LGIT Module supports HCI 3-wire transport(UART H5) Item Min Typ Max Unit Delay time, UART_CTS_N low to UART_TXD valid - - 1.5 Bit periods Setup time, UART_CTS_N high before midpoint of stop bit - - 0.5 Bit periods Delay time, midpoint of stop bit to UART RTS_N high - - 0.5 Bit periods Baud rates range(default rate : 115200bps) 9600 - 4M bps -. UART bus timing specifications -. UART bus timing
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (37 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics 6) PCM characteristics -. LGIT Module PCM interface can connect to linear PCM codec devices in master or slave mode. In master mode, the device generates the PCM_CLK and PCM_SYNC signals. In slave mode, these signals are provided by another master on the PCM interfaces as inputs to the devices -. Short frame sync, master mode timing diagram -. Short frame sync, master mode interface timing specifications Item Min Typ Max Unit PCM bit clock frequency - - 12 MHz PCM bit clock LOW 41 - - ns PCM bit clock HIGH 41 - - ns PCM_SYNC delay 0 - 25 ns PCM_OUT delay - - 25 ns PCM_IN setup 8 - - ns PCM_IN hold 8 - - ns Delay from rising edge of PCM_BCLK during last bit period to PCM_OUT becoming high impedance - - 25 ns
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (38 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics 6) PCM characteristics -. Short frame sync, slave mode timing diagram -. Short frame sync, slave mode interface timing specifications Item Min Typ Max Unit PCM bit clock frequency - - 12 MHz PCM bit clock LOW 41 - - ns PCM bit clock HIGH 41 - - ns PCM_SYNC setup 8 - - ns PCM_SYNC hold 8 - - ns PCM_OUT delay - - 25 ns PCM_IN setup 8 - - ns PCM_IN hold 8 - - ns Delay from rising edge of PCM_CLK during last bit period to PCM_OUT becoming high impedance 0 - 25 ns
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (39 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics 6) PCM characteristics -. Long frame sync, master mode timing diagram -. Long frame sync, master mode interface timing specifications Item Min Typ Max Unit PCM bit clock frequency - - 12 MHz PCM bit clock LOW 41 - - ns PCM bit clock HIGH 41 - - ns PCM_SYNC delay 0 - 25 ns PCM_OUT delay 0 - 25 ns PCM_IN setup 8 - - ns PCM_IN hold 8 - - ns Delay from rising edge of PCM_BCLK during last bit period to PCM_OUT becoming high impedance 0 - 25 ns
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (40 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics 6) PCM characteristics -. Long frame sync, slave mode timing diagram -. Long frame sync, slave mode interface timing specifications Item Min Typ Max Unit PCM bit clock frequency - - 12 MHz PCM bit clock LOW 41 - - ns PCM bit clock HIGH 41 - - ns PCM_SYNC setup 8 - - ns PCM_SYNC hold 8 - - ns PCM_OUT Delay 0 - 25 ns PCM_IN setup 8 - - ns PCM_IN hold 8 - - ns Delay from falling edge of PCM_BCLK or PCM_SYNC during last bit period to PCM_OUT becoming high impedance 0 - 25 ns
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (41 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics -. SDIO default mode timing(min.Vih = 0.7 X VIO, max.Vil = 0.2 x VIO) 7) SDIO characteristics -. RBHP-B213A support up to SDIO 3.0 specification · DS : Default speed(DS) up to 25MHz(3.3V signaling) · SDR12 : SDR up to 25MHz(1.8V signaling) · SDR25 : SDR up to 50MHz(1.8V signaling) · SDR50 : SDR up to 100MHz(1.8V signaling) · SDR104 : SDR up to 208MHz(1.8V signaling) · DDR50 : DDR up to 50MHz(1.8V signaling)
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (42 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics Item Symbol Min Typ Max Unit SDIO CLK Freq.(data transfer mode) fPP 0 - 25 MHz Freq.(identification mode) fOD 0 400 KHz Clock low time tWL 10 - - ns Clock high time tWH 10 - - ns Clock rise time tTLH - - 10 ns Clock low time tTHL - - 10 ns Input : CMD, DAT(referenced to CLK) Input setup time tISU 5 - - ns Input hold time tIH 5 - - ns Output : CMD, DAT(referenced to CLK) Output delay time-data transfer mode tODLY 0 - 14 ns Output delay time-data identification mode tODLY 0 - 50 ns -. SDIO default mode bus timing parameters
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (43 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released -. SDIO high speed mode bus timing(min.Vih = 0.7 X VIO, max.Vil = 0.2 x VIO) Item Symbol Min Typ Max Unit SDIO CLK Freq.(data transfer mode) fPP 0 - 50 MHz Freq.(identification mode) fOD 0 - 400 KHz Clock low time tWL 7 - - ns Clock high time tWH 7 - - ns Clock rise time tTLH - - 3 ns Clock low time tTHL - - 3 ns -. SDIO high speed mode bus timing parameters 10. Electrical Specification 10.3 I/O characteristics
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (44 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released Input : CMD, DAT(referenced to CLK) Input setup time tISU 6 - - ns Input hold time tIH 2 - - ns Output : CMD, DAT(referenced to CLK) Output delay time-data transfer mode tODLY - - 14 ns Output delay time-data identification mode tODLY 2.5 - - ns Total system capacitance(each line) CL - - 40 pF 10. Electrical Specification 10.3 I/O characteristics -. SDIO SDR mode clock timing Item Symbol Min Typ Max Unit Item Symbol Min Max Unit Comments - tCLK 40 50 ns SDR12 mode 20 400 ns SDR25 mode 10 - ns SDR50 mode 4.8 - ns SDR104 mode - tCR, tCF - 0.2 X tCLK ns tCR, tCF < 2.0ns(max)@100MHz CCARD = 10pF tCR, tCF < 0.96ns(max)@208MHz CCARD = 10pF Clock duty - 30 70 % -
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (45 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics -. SDIO SDR mode Device input timing Item Symbol Min Max Unit Comments SDR104 Mode tIS 1.4 - ns CCARD = 10pF, VCT=0.975V tIH 0.8 - ns CCARD = 5pF, VCT=0.975V SDR50 Mode tIS 3 - ns CCARD = 10pF, VCT=0.975V tIH 0.8 - ns CCARD = 10pF, VCT=0.975V
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (46 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics -. SDIO SDR mode Device output timing(SDR modes up to 100MHz) Symbol Min Max Unit Comments tODLY - 7.5 ns tCLK > 10ns, CL = 30pF using driver type B for SDR50 tODLY - 14.0 ns tCLK > 20ns, CL = 40pF using for SDR12, SDR25 tOH 1.5 - ns Hold time at the tODLY (min) CL = 15pF
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (47 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics -. SDIO SDR mode Device output timing(SDR modes 100MHz to 208MHz) Symbol Min Max Unit Comments tOP 0 2 UI Card output phase ΔtOP -350 +1550 Ps Delay variation due to temp. change after tuning ΔtODW 0.60 - UI ΔtODW = 2.88ns @208MHz
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (48 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics -. SDIO DDR50 mode Clock timing Item Symbol Min Max Unit Comments - tCLK 20 - ns DDR50 mode - tCR, tCK - 0.2x tCLK ns tCR, tCF < 4.0ns(max)@50MHz CCARD = 10pF Clock duty - 45 55 % -
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (49 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics -. SDIO DDR50 mode Data timing Item Symbol Min Max Unit Comments Input CMD Input Setup time tISU 6 - ns CCARD < 10pF(1CARD) Input Hold time tIH 0.8 - ns CCARD < 10pF(1CARD) Output CMD Output delay time tODLY - 13.7 ns CCARD < 30pF(1CARD) Output hold time tOH 1.5 - Ns CCARD < 15pF(1CARD) Input DAT Input Setup time tISU2X 3 - ns CCARD < 10pF(1CARD) Input Hold time tIH2X 0.8 - ns CCARD < 10pF(1CARD) Output DAT Output delay time tODLY2X 7.5 ns CCARD < 25pF(1CARD) Output holdtime tODLY2X 1.5 - Ns CCARD < 15pF(1CARD)
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (50 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics 8) PCI Express characteristics Parameters Symbol Comments Min. Typ. Max Unit Baud rate BPS - - 2.5 - Gbaud Reference clock amplitude Vref LVPECL, AC coupled 1.0 - - V -. PCI Express Reference CLK Parameters Symbol Comments Min. Typ. Max Unit Differential termination ZRX-DIFF-DC Differential termination 80 100 120 Ω DC impedance ZRX-DC DC common-mode impedance 40 50 60 Ω Powered down termination(POS) ZRX-HIGH-IMP-DC-POS Power-down or RESET high Impedance 100k - - Ω Powered down termination(NEG) ZRX-HIGH-IMP-DC-NEG Power-down or RESET high Impedance 1k - - Ω Input voltage VRX-DIFFp-p AC coupled, differential(p-p) 175 - - mV Jitter tolerance TRX-EYE Minimum receiver eye width 0.4 - - UI Differential return loss RLRX-DIFF Differential return loss 10.0 - - dB Common-mode return loss RLRX-CM Common-mode return loss 6 - - dB Unexpected electrical idle enter detect threshold integration time RX-IDEL-DET-DIFFENTERTIME An unexpected electrical idle must be recognized no longer than this time to signal an unexpected idle condition. - - 10.0 ms Signal detect threshold VRX-IDLE-DET-DIFFpp Electrical idle detect threshold 65.0 - 175 mV -. PCI Express Receiver s
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (51 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics 8) PCI Express characteristics Parameters Symbol Comments Min. Typ. Max Unit Output voltage VTX-DIFFp-p Differential p-p, programmable in 16 steps 0.8 - 1200 mV Output voltage rise time VTX-RISE 20% to 80% 0.125 (2.5 GT/s) 0.15 (5 GT/s) - - UI Output voltage fall time VTX-FALL 80% to 20% 0.125 (2.5 GT/s) 0.15 (5 GT/s) - - UI RX detection voltage swing VTX-RCV-DETECT The amount of voltage change allowed during receiver detection. - - 600 mV TX AC peak common-mode voltage(5 GT/s) VTX-CM-AC-PP TX AC common mode voltage (5 GT/s) - - 100 mV TX AC peak commonmode voltage(2.5 GT/s) VTX-CM-AC-P TX AC common mode voltage (2.5 GT/s) - - 20.0 mV Absolute delta of DC common-model voltage during L0 and electrical idle VTX-CM-DC-ACTIVE-IDLE- DELTA Absolute delta of DC common-model voltage during L0 and electrical idle. 0 - 100 mV Absolute delta of DC common-model voltage between D+ and D- VTX- CM-DC-LINE-DELTA DC offset between D+ and D- 0 - 25.0 mV Electrical idle differential peak output voltage VTX-IDLE-DIFF-AC-p Peak-to-peak voltage 0 - 20.0 mV -. PCI Express Transmitter
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (52 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 10. Electrical Specification 10.3 I/O characteristics 8) PCI Express characteristics Parameters Symbol Comments Min. Typ. Max Unit TX short circuit current ITX-SHORT Current limit when TX output is shorted to ground. - - 90.0 mA DC differential TX termination ZTX-DIFF-DC Low impedance defined during signaling (parameter is captured for 5.0 GHz by RLTX-DIFF) 80.0 - 120 Ω Differential return loss RLTX-DIFF Differential return loss 10 (min) for 0.05: 1.25 GHz - - dB Common-mode return loss RLTX-CM Common-mode return loss 6.0 - - dB TX eye width TTX-EYE Minimum TX eye width 0.75 - - UI
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (53 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 1) Recommended operation conditions 2) Current consumption Parameter Unit Stand-by (BT & WLAN) mA Average 10 WLAN Continuous Rx mA 180 WLAN Continuous Tx2) mA 420 Bluetooth Connection mA 20 Parameter Unit Operating Temperature Range ℃ Min Max -40 +85 Supply Voltage : VBATT (3.3V) V 3.01) 3.6 3) ESD Precautions RBHP-B213A is classified as a JESD22-A114(HBM) class 1C(1kV) product. Apply ESD static handling precautions during manufacturing. 10. Electrical Specification 10.4 Operating Conditions 4) External 32.768KHz low-power oscillator(LPO) External 32.768KHz precision oscillator is required. Parameter Unit Nominal input frequency KHz LPO clock 32.768 Frequency accuracy ppm ±200 Single input amplitude mV, p-p 200 ~ 1800 Signal type Square-wave or sine-wave Supply Voltage : VIO (1.8V) 1.62 1.98 V l 1) The BCM88359 is functional across this range of voltages. Optimal RF performance specified in the RBHP-B213A approval sheet, however , is guaranteed only for min. 3.2V including VBAT ripple 2) MIMO condition t
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (54 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 11. Pin Configuration < Opposite (Host) Pin Map (Top View) > 1 20 21 Position#1 Indicator <FCI 61082-041 > 40 * * *
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (55 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 11. Pin Configuration No. Pin Name I/O Description 1 GND - Ground 2 BT_UART_RTS I/O Bluetooth UART request to send 3 BT_UART_CTS I/O Bluetooth UART clear to send 4 BT_UART_TXD I/O Bluetooth UART signal output 5 BT_UART_RXD I/O Bluetooth UART signal input 6 VIO I BT, WLAN VDDIO supply voltage.(3.3V or 1.8V) - BT and WLAN should be same power rail 7 GND - Ground 8 SDIO_CLK I SDIO clock 9 SDIO_CMD I/O SDIO command line 10 SDIO_DATA3 I/O SDIO data line 3 11 SDIO_DATA2 I/O SDIO data line 2 12 SDIO_DATA1 I/O SDIO data line 1 13 SDIO_DATA0 I/O SDIO data line 0 14 GND - Ground 15 GND - Ground g
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (56 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 11. Pin Configuration No. Pin Name I/O Description 16 LPO I Low power clock input (32.768KHz, 200~1800mV P-P) 17 GND - Ground 18 VBAT I Positive supply - Supply voltage : Typical 3.3V. 19 VBAT I Positive supply - Supply voltage : Typical 3.3V. 20 VBAT I Positive supply - Supply voltage : Typical 3.3V. 21 GND - Ground 22 SDIO_DIS I SDIO_DIABLE : Low : SDIO Enabled, High : SDIO Disabled 23 PCIE_EN I PCIE_ENABLE : Low : PCIE Disabled, High : PCIE Enabled 24 GND - Ground 25 BT_PCM_IN I PCM data input 26 BT_PCM_OUT O PCM data output 27 BT_PCM_CLK I/O PCM clock, can be master (output) or slave (input) 28 BT_PCM_SYNC I/O PCM sync signal, can be master (output) or slave (input) 29 PCIE_TD_P O PCIE Transmitter differential positive 30 PCIE_TD_N O PCIE Transmitter differential negative
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (57 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 11. Pin Configuration No. Pin Name I/O Description 31 PCIE_CLK_N I PCIE differential clock input negative 32 PCIE_CLK_P I PCIE differential clock input positive 33 PCIE_RD_N I PCIE Receiver differential negative 34 PCIE_RD_P I PCIE Receiver differential positive 35 PCIE_CLKREQ O PCIE clock request signal 36 PCIE_PERST_N I PCIE system reset. 37 PCIE_PME_L O PCIE power management event output 38 SDIO_PADVIO I SDIO_PADVDDIO :If VIO_SD=1.8Vhigh, If VIO_SD=3.3Vlow 39 BT_REG_ON I BT Power on Reset 40 WL_REG_ON I WLAN Power on reset - Internal 200KΩ pull-down
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (58 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 12. Reliability Test Conditions NO ITEM Condition Characteristics 1 High Temp. Load Test Initial value measured at standard test condition. Test Conditions: 25℃ → 85℃, 100hr(Over for 1hr) Supply Voltage Condition: standard ± 5% In standard test condition, take measurements within 3hr. - No electrical problem 2 Low Temp. Load Test Initial value measured at standard test condition. Test Conditions: 25℃ → -40℃, 100hr(Drop for 1 hr) Supply Voltage Condition: standard ± 5% In standard test condition, take measurements within 3hr. - No electrical problem 3 High Temp. Storage Test Initial value measured at standard test condition. Test Conditions: 105℃, 168hr In standard test condition, take measurements within 3hr. - No electrical problem 4 Low Temp. Storage Test Initial value measured at standard test condition. Test Conditions: -40±3℃, 168hr In standard test condition, take measurements within 3hr. - No electrical problem 5 Sweep Sine Vibration Test IInitial value measured at standard test condition. Test Conditions: 10~50Hz, 1mm p-p 2hr In standard test condition, take measurements within 3hr. - No electrical problem 6 Drop Test Initial value measured at standard test condition. Test Conditions: - Test height: 100 cm - Test times: 10 times Drop the module onto a 10mm thickness plywood. In standard test condition, take measurements within 3hr. - No mechanical damage 7 Shock Test Initial value measured at standard test condition. Test Conditions: - Impact acceleration: 50G(m/sec2) - Impact time: 11 msec - Impact times and direction: 10 times each in 6 directions In standard test condition, take measurements within 3hr. - No mechanical damage 8 High Temperature Durability Initial value measured at standard test condition. Test Conditions: - Test Temp.: 85℃ - Test times : 500Hr Supply Voltage Condition: - V min: until 10% of operational cycles - V normal: until 80% of operational cycles - V max: until 10% of operational cycles In standard test condition, take measurements within 3Hr - No electrical problem 12.1 Items related with Non-Solderability(ES96100-02) x
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (59 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released NO ITEM Condition Characteristics 9 Against flux Initial value measured at standard test condition. Test Conditions -Soak 5 seconds in a I.P.A and let waiting condition for 35 seconds. After then test. - No electrical problem 10 Temperature and Humidity Cycling Initial value measured at standard test condition. Test Conditions: 3 cycle condition. In standard test condition, take measurements 2hr after. - No electrical problem 11 Dew Condensation test Initial value measured at standard test condition. Test Conditions: 3 cycle condition. -30℃ (1 Hr) -30℃ → 25℃, 90%RH (within 1 min) 25℃, 90%RH (1 Hr) - On : 15 min / Off : 15 min In standard test condition, take measurements 2hr after. - No electrical problem 12 High humidity and Temp. load test IInitial value measured at standard test condition. Test Conditions: 60℃, 80%, 48hr In standard test condition, take measurements within 3hr. - No electrical problem 13 Dust IInitial value measured at standard test condition. Test Conditions: JIS Z 8901, 5kg In standard test condition, take measurements within 3hr. - No electrical problem 12. Reliability Test Conditions Temperature (℃) -40±2 23±5 55±2 70±2 4 4.5 14.5 17 19 20.5 22.5 24 Time (hour) Humidity (%) 60±15 80 4 4.5 14.5 17 19 20.5 22.5 24 Time (hour) 12.1 Items related with Non-Solderability(ES96100-02)
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (60 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 12. Reliability Test Conditions NO ITEM Condition Characteristics 14 Temperature Drift Test Initial value measured at standard test condition. Test Conditions: Take measurements sustaining each temperature. - No electrical problem Temperature (℃) 25 70 65 55 45 -20 -10 0 1 hour 12.1 Items related with Non-Solderability(ES96100-02) 15 Dust IInitial value measured at standard test condition. Test Conditions: JIS Z 8901, 5kg In standard test condition, take measurements within 3hr. - No electrical problem 16 Complex Environment IInitial value measured at standard test condition. Test Conditions: -20℃~60℃, 10~50Hz, 1G In standard test condition, take measurements within 3hr. - No electrical problem 17 Operation Durability IInitial value measured at standard test condition. Test Conditions: 25±5℃ 60±20%, 1500Hrs In standard test condition, take measurements within 3hr. - No electrical problem 18 ESD IInitial value measured at standard test condition. Test Conditions: ±1KV 5time 150pF/330Ω In standard test condition, take measurements within 3hr. - No electrical problem
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (61 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 12.2 Items related with Solderability(ES90000-04) NO ITEM Condition Characteristics 1 High Temperature and Humidity Load Test Initial value measured at standard test condition. Test Conditions: 85±3℃, 85±5%RH, 1000hr In standard test condition, take measurements within 3hr. - Whisker, No electrical problem 2 Thermal Shock Initial value measured at standard test condition. Test Conditions: -40℃ ( 10 min) -40℃ → 85℃, (within 10 min) 85℃ ( 10 min) 85℃ → -40℃, (within 10 min) - Test cycle : 1000 cycles - Test Times : 667 Hr In standard test condition, take measurements within 3Hr. - No Whisker, Bond strength, section inspection, electrical problem 3 Power and Temperature Cycling Initial value measured at standard test condition. Test Conditions: 100 cycle condition - Test Times : 100 Hr Supply Voltage Condition: standard ± 5% Power Condition: -35℃ ( 10 min) -35℃ → 75℃, (Temp. variation velocity : over 6℃/min) 75℃ ( 10 min) 75℃ → -35℃, (Temp. variation velocity : over 6℃/min) - On: 300 sec , Off: 300 sec In standard test condition, take measurements within 3Hr 4 Random Vibration test With operation Initial value measured at standard test condition. Test Conditions: - Frequency : 10 ~ 1000Hz - Power spectrum density : 0.0296 ~ 9.63 (m/s3)2/Hz - Direction : X/Y/Z, 8hr/Axis In standard test condition, take measurements 2hr after. 12. Reliability Test Conditions
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (62 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 13. Block Diagram W_Tx W_Rx BCM88359 RBHP-B213A BT/WiFi Combo Module 37.4MHz (crystal) SW W_Tx W_Rx SW W_Tx W_Rx 5GHz FEM 2.4GHz FEM Diplexer ESD protection 2.4G/5G WLAN ANT 1 VBAT(3.3V) BT_PCM ≠4 WL_REG_ON BT_REG_ON BT_UART ≠4 SDIO ≠6 VIO LPO_CLK (32.768kH z Clock) SDIO_DIS PCIE ≠9 B_Tx/Rx SDIO_PAD PCIE_EN WiFi Core1 SW W_Tx W_Rx 5GHz FEM Diplexer ESD protection Bluetooth /5G WLAN ANT 0 WiFi Core0 Bluetooth j
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (63 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 14. Reference Circuit u
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (64 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 15. Reflow Profile 150℃ 60~120 sec Temperature t [sec] Ramp up Soak(flux activation) 200℃ 250℃ 217℃ 60~150 sec Reflow Cool down 3℃ per second 3℃ per second maximum 6℃ per second maximum Tsmin Tsmax Profile Feature Pb-free Assembly Initial ramp-up rate 3℃ per second maximum Preheat Temperature minimum(Tsmin) Temperature maximum(Tsmax) Time(minimum to maximum) 150℃ 200℃ 60-120s Ramp-up rate Tsmax to TL 3℃ per second maximum Liquidus Temperature(TL) 217℃ Time above TL 60-150s Peak temperature 250℃ maximum Time within 5℃ of actual peak 10s Ramp-down rate 6℃ per second maximum
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (65 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 16. Recommended Land Pattern <Unit : mm> 1)Top view <FCI 61082-041 > c
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (66 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 17. Packing Information of top on BOX.(400X250X285)
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (67 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 17. Packing Information No. Index ① POSITION (ITEM / OUTBOX) ② CUSTOMER ③ FIRMWARE VERSION (vX.X) ④ SHIPPING DATE (YYYY.MM.DD) ⑤ BARCODE (Customer P/N, Quantity) Ex) EAT63433501 130 ⑥ CUSTOMER P/N ⑦ QUANTITY ⑧ MODEL P/N ⑨ LOT NUMBER ⑩ BARCODE (Lot No.) Ex) 6530-001 ⑪ BARCODE (Model P/N, Lot No.1) Ex) RBHP-B213A.6530-001.1 6530 - 001 Item LGE v1.0 2016.05.30 EAT63433501 130 Spec RBHP-B213A LotNo ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪ q
TITLE : Specifications for approval (RBHP-B213A) (CUSTOMER P/NO : EAT63433501 ) REV 1.6 (68 / 68) R E V APPD CHKD DSGD DOCUMENT NO. 6-3 RBHP-B213A LG Innotek Co., Ltd 1.4 2017. 07.14. Rev1.4 Released 1.5 2017. 08.10. Rev1.5 Released (30) - 4021 1.2 2017. 05.23. Rev1.2 Released 1.3 2017. 06.27. Rev1.3 Released 1.6 2017. 09.06. Rev1.6 Released 18. Ordering Information P Host Interface PCIe R B H P - B 2 1 3 A B Chipset Maker Broadcom 213 Serial Number 213 A Revision A Version H Module Type BT(Class2)+WLAN RB Product Bluetooth
FCC WARNING STATEMENTThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operationAny changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user's authority to operate the equipment.Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Modifications not expressly approved by the manufacturer could void your authority to operate the equipment under FCC rules.FCC RF Radiation Exposure StatementThis equipment complies with FCC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Information for OEM integratorThe OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user manual of the end product. The user manual which is provided by OEM integrators for end users must include the following information in a prominent location.“To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” Label for end product must include “Contains FCC ID: BEJRBHP-B213A, IC: 2703H-RBHP-B213A" or "A RF transmitter inside, FCC ID: BEJRBHP-B213A, IC: 2703H-RBHP-B213A".
IC WARNING STATEMENTThis device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions : (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.This equipment complies with IC RF Radiation exposure limits set forth for an uncontrolledenvironment. This device and its antenna must not be co-located or operating in conjunctionwith any other antenna or transmitter.This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.Cet équipement est conforme aux limites établies par Industrie Canada en matière d'exposition aux radiofréquences dans un environnement non contrôlé. Cet appareil et son antenne ne doivent pas être colocalisés ou fonctionner en conjonction avec tout autre antenne ou émetteur.Cet équipement doit être installé et utilisé avec une distance minimale de 20cm entre le radiateur et votre corps.

Navigation menu