LG Electronics USA RBHP-B213A Bluetooth Module User Manual SPECIFICATIONS FOR APPROVAL
LG Electronics USA Bluetooth Module SPECIFICATIONS FOR APPROVAL
User manual
We only use Bluetooth. 5G WLAN function is disabled by software. CUSTOMER : LGE DATE : 2017.09.06. the module is to be installed in vehicle only SPECIFICATIONS FOR APPROVAL PRODUCT NAME : BT(v4.2) + WLAN(802.11a/b/g/n/ac) 2.4G SISO/5G MIMO MODEL NAME : RBHP-B213A CUSTOMER P/N : EAT63433501 APPROVAL REMARK APPENDIX Designed Checked Approved LG Innotek Co., Ltd. DOCUMENT No. RBHP-B213A PAGE 68 (00)-0070 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (2 / 68) (CUSTOMER P/NO : EAT63433501 ) Change History of Revision Revision Date Contents of Revision Change 0.1 2015.4.23. Establishment 0.2 2015.9.15. Digital I/O Pins IN/OUT Range Spec. changed 0.3 P.29 Pin configuration was modified P.52 Recommended Land Pattern updated P.59 P18 P22 PCIe power-on timing inserted P34 Pin configuration is modified(PCIe inserted) P51 P4 P58 2016.2.13. 2.4G WiFi power spec. updated 5G WiFi power spec. updated 0.4 0.5 Remark 2016.4.20. Model number is changed to RBHP-B213A(PCIe) 2016.6.10 Application updated Blockdiagram updated Customer P/N inserted 0.6 2016.9.4 P1 Block diagram updated 0.7 2016.10.14 Bluetooth, WiFi Radiation performance spec. inserted 0.8 2016.10.26 Customer P/N modified 0.9 2017.01.06 ESD spec. modified P12,13, 14, 17,18, 22 P1 Antenna Tube color modified 1.0 P58 2017.02.28 Module Radiation sensitivity spec. modified BT/WiFi core0 5G Antenna tube color changed P49 P6 P9 P6 1.1 2017.05.17 Label information updated P5 1.2 2017.05.23 Out box label information updated P63 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (3 / 68) (CUSTOMER P/NO : EAT63433501 ) Change History of Revision Revision 1.3 Date Contents of Revision Change 2017.6.27. PCIE power-on timing updated Remark P35 PCIE I/O characteristics updated P50 RF performance guarantee min. VBAT voltage updated P53 Application schematic updated P63 1.4 2017.7.17. Bluetooth version updated P1 1.5 2017.8.10. Low temp. operating comment added in Clause 5. (Customer Request) P5 1.6 2017.9.06. Reliability spec. updated P58 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (4 / 68) (CUSTOMER P/NO : EAT63433501 ) Table of Contents 1. Application 2. Quality 3. Appearance and Characteristics 4. Application of Bluetooth Module 5. Maximum Rating 6. Test 7. Labeling Information 8. Mechanical Dimension 9. General Features 10. Electrical Specification 11. Pin Configuration 12. Reliability Test 13. Block Diagram 14. Reference Circuit 15. Reflow Profile 16. Recommended Land Pattern 17. Packing Information 18. Ordering Information 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (5 / 68) (CUSTOMER P/NO : EAT63433501 ) 1. Application This specification is applied to LGInnotek Bluetooth (v4.2)and 2.4GHz SISO/5GHz MIMO WLAN(802.11a/b/g/n/ac) Module RBHP-B213A which includes BCM88359 2. Quality Quality should meet each condition which mentioned on this specification. However, the items which are not mentioned on this specification follow the inspection agreements and standards which are agreed with both companies. 3. Appearance and Characteristics 1) Appearance Appearance should not be contaminated by harmful materials and should not have cracks etc. Mechanical dimensions should meet the contents of clause 8. 2) Characteristics Electrical characteristics should meet the contents of clause 10. 4. Application of Bluetooth v4.2 and 2.4GHz/5GHz WLAN(IEEE 802.11.a/b/g/n/ac) 1) Automotive 5. Maximum Rating NO ITEM Operating Temperature Range Storage Temperature Range Rating -40 ~ +85 -40 ~ +105 UNIT ℃ ℃ VBAT Voltage Range VIO Voltage Range -0.5 ~ 6.0 -0.5 ~ 3.9 VBAT Max. Current VIO Max. Current 700(@3.3V) 50(@1.8V) mA mA ■ RBHP-B213A Module assures operating normally at -40 ~ +85℃. 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (6 / 68) (CUSTOMER P/NO : EAT63433501 ) 6. Test Electrical characteristics are tested for every products. However, if there are any objection in judgments, it should be treated with agreements of companies. 7. Labeling Information GWANGGAETOH Index ① PRODUCT ① RBHP-B213A ② ② MODEL PART NO. ③ 7 04 GJ 27 0059 ③④ ⑤ ⑥ No. ⑦ EAT63433501 ⑧ ④ MANUFACTURED YEAR (0~9) MANUFACTURED MONTH(1,2, …9, A,B,C) ⑤ GwangJu ⑥ MANUFACTURED DATE (1~31) ⑦ MANUFACTURED SERIAL NUMBER(0001~9999) ⑧ Customer P/N ⑨ ⑨ QR CODE INFORMATION : EAT63433501_704GJ270059 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (7 / 68) (CUSTOMER P/NO : EAT63433501 ) 8. Mechanical Dimension 1) Dimension without Antenna Ass’y [Unit: mm] 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (8 / 68) (CUSTOMER P/NO : EAT63433501 ) 8. Mechanical Dimension 2) Dimension with Antenna Ass’y [Unit: mm] 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (9 / 68) (CUSTOMER P/NO : EAT63433501 ) 9. General Features 9.1 BT(v4.2) + 2.4GHz/5GHz WLAN(IEEE 802.11a/b/g/n/ac) 2.4G SISO/5G MIMO 1) Features • Operation Voltage is 3.3V/1.8V Dual Power Rail • WiFi Single-stream up to 866 Mbps data rate • Automotive Module : All components are AEC-Q 100/200 qualified • Support 2 Antenna port : ANT0 : Bluetooth/5G WLAN, ANT1 : 2.4G/5G WLAN • Integrated WLAN PA, RF Switch and LNA • RoHS Compliant • Size : 35.3 x 35.3 x 7.8 mm3 • Support bandwidth : HT20 / HT40 / VHT80 • HOST Interface : PCIE/SDIO(WLAN), UART(BT), PCM(I2S) • Package type : Connector type(B to B) 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (10 / 68) (CUSTOMER P/NO : EAT63433501 ) 9. General Features 9.2 Bluetooth(BT v4.2+EDR compliant) 1) Bluetooth Key Features • Supports key features of upcoming Bluetooth standards • Fully supports Bluetooth Core Specification version 4.2 + (Enhanced Data Rate) EDR features: -. Adaptive Frequency Hopping (AFH) -. Quality of Service (QoS) -. Extended Synchronous Connections (eSCO) – Voice Connections -. Fast Connect (interlaced page and inquiry scans) -. Secure simple Pairing (SSP) -. Sniff Sub rating (SSR) -. Encryption Pause Resume (EPR) -. Extended Inquiry Response (EIR) -. Link Supervision Timeout (LST) • UART baud rates up to 4 Mbps • Supports all Bluetooth 4.2 packet types • Supports maximum Bluetooth data rates over HCI UART • Multipoint operation with up to seven active slaves -. Maximum of seven simultaneous active ACL links -. Maximum of three simultaneous active SCO and eSCO connections with scatternet support • Narrowband and wideband packet loss concealment • Scatternet operation with up to four active piconets with background scan and support for scatter mode • High-speed HCI UART transport support • Channel quality driven data rate and packet type selection • Standard Bluetooth test modes • Extended radio and production test mode features • Full support for power savings modes -. Bluetooth clock request -. Bluetooth standard sniff -. Deep-sleep modes and software regulator shutdown 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (11 / 68) (CUSTOMER P/NO : EAT63433501 ) 9. General Features 9.3 WLAN 1) WLAN RF band & modulation Features • Dual-band 2.4GHz and 5GHz 802.11 a/b/g/n/ac(802.11ac compliant) • Up to 866Mbps data rate • Supports 20, 40 and 80MHz channels with optional SGI(256 QAM modulation) • Tx and Rx low-density parity check(LDPC) • Supports IEEE 802.11ac/n beamforming • Supports PCIe v3.0-compliant interface running at GEN1 speeds • Supports two antennas with Bluetooth/5G WLAN and 2.4G/5G WLAN antenna • Supports standard SDIO V3.0 (up to SDR104 mode at 208MHz, 4-bit and 1-bit) • Backward compatibility with SDIO v2.0 host interface • WPA and WPA2(Personal) support for powerful encryption and authentication • AES and TKIP in hardware for faster data encryption and IEEE 802.11i compatibility • Reference WLAN subsystem provides Wi-Fi protected Setup(WPS) 2) WLAN MAC features • Enhanced MAC for supporting IEEE 802.11ac features • Transmission and reception of aggregated MPDUs(A-MPDU) for high throughput(HT) • Support for power management schemes, including WMM power-save multipoll(PSMP) and multiphase PSMP operation • Support for immediate ACK and block-ACK policies • Inter-frame space timing support, including RIFS • Back-off counters in hardware for supporting multiple priorities as specified in the WMM specification • Timing synchronization function(TSF), network allocation vector(NAV) maintenance, and target beacon transmission time(TBTT) generation in hardware • Hardware offload for AES-CCMP, legacy WPA TKIP, legacy WEP ciphers, WAPI, and support for key management • Programmable independent basic service set(IBSS) or infrastructure basic service set functionality 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (12 / 68) (CUSTOMER P/NO : EAT63433501 ) 9. General Features 9.3 WLAN 3) WLAN PHY features • Programmable data rates from MCS0-9 in 20MHz, 40MHz, and 80MHz channels, as specified in IEEE 802.11ac • Improved performance with channel smoothing and spur canceller support • Supports Optional short GI and Green field modes in Tx and Rx • Tx and Rx LDPC for improved range and power efficiency • Beamforming support • Supports IEEE 802.11h/k for worldwide operation • Advanced algorithms for low power, enhanced sensitivity, range, and reliability • IEEE 802.11a, 11b, 11g, 11n, 11ac single stream PHY standards • Designed to meet FCC and other worldwide regulatory requirements 9.4 JEDEC MSL (Moisture Sensitivity Level) Test • MSL 3 Level (Floor Life Time : 168Hrs. / Condition : ≤30℃, 60% RH) • Standard : IPC / JEDEC J-STD-020C Bake 24Hrs. / 125℃ Soak 40Hrs. / 60℃, 60% RH Reflow 3 times / 240℃ 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (13 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.1 Bluetooth 1) Basic Data Rate - Rx Performance General Performance Parameter Condition Min Frequency Range Impedance Typ 2402 BT_ANT Pin 50 Max Unit 2480 MHz Ohm Receiver Performance Parameter Condition Min Typ Max Unit Sensitivity level (BER≤0.1%) (Radiation performance) Single slot -84 (-75) dBm Sensitivity level (BER≤0.1%) (Radiation performance) Multi slot -84 (-75) dBm C/I performance1) (BER≤0.1%) C/I co-channel , Input=-60dBm 11 dB C/I 1MHz , Input=-60dBm dB C/I 2MHz , Input=-60dBm -20 dB -40 dB Image radio , Input=-67dBm -9 dB Image±1 -20 dB 30MHz ~ 2000MHz -10 dBm 2000MHz ~ 2400MHz -27 dBm 2500MHz ~ 3000MHz -27 dBm 3000MHz ~ 12.75GHz -10 dBm Input=-64dBm, n=5 -39 dBm -20 dBm C/I ≥3MHz Out-of-band Blocking2) (BER≤0.1%) Intermodulation (BER≤0.1%) , Input=-67dBm , Input=-67dBm Maximum Input Level (BER≤0.1%) 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (14 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.1 Bluetooth 2) Basic Data Rate - Tx Performance Transmitter Performance Parameter Condition Min Typ Max Unit Transmit Power (Radiation performance) All temperature -6 (-8) (6) dBm Power density All temperature 20 dBm Frequency Range All temperature 2402 2480 MHz 20dB bandwidth All temperature 1000 KHz Adjacent channel power3) ±2MHz -20 dBm ±3MHz -40 dBm ±4MHz -40 dBm 30MHz ~ 1GHz -36 dBm 1GHz ~ 12.75GHz -30 dBm 1.8GHz ~ 1.9GHz -47 dBm 5.1GHz ~ 5.3GHz -47 dBm ΔF1avg 140 175 KHz ΔF2max 115 KHz ΔF2avg/ΔF1avg 80 Initial Carrier Frequency Tolerance DH1 packet -75 75 KHz Carrier Frequency Drift Five slot packet(DH5) -40 40 KHz Out-band Spurious Emission Modulation Characteristics 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (15 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.1 Bluetooth 3) Enhanced Data Rate - Rx Performance Enhanced Data Rate Receiver Performance Parameter Condition Sensitivity at 0.01% BER (Radiation performance) π/4 DQPSK/8DPSK Maximum received signal at 0.1% BER Min Typ Max Unit -80 (-75) dBm π/4 DQPSK -20 dBm 8DPSK -20 dBm π/4 DQPSK 13 dB 8DPSK 21 dB π/4 DQPSK dB 8DPSK dB π/4 DQPSK dB 8DPSK dB π/4 DQPSK -30 dB 8DPSK -25 dB π/4 DQPSK -20 dB 8DPSK -13 dB π/4 DQPSK -40 dB 8DPSK -33 dB π/4 DQPSK -40 dB 8DPSK -33 dB π/4 DQPSK -7 dB 8DPSK dB C/I co-channel at 0.1% BER Adjacent channel selectivity C/I F=F0+1MHz Adjacent channel selectivity C/I F=F0-1MHz Adjacent channel selectivity C/I F=F0+2MHz Adjacent channel selectivity C/I F=F0-2MHz Adjacent channel selectivity C/I F≥F0+3MHz Adjacent channel selectivity C/I F≤F0-5MHz Adjacent channel selectivity C/I F=Fimage 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (16 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.1 Bluetooth 4) Enhanced Data Rate - Tx Performance Enhanced Data Rate Transmitter Performance Parameter Min Typ Max Unit Relative transmit power. -4 -1 dB π/4 DQPSK max carrier frequency stability |ωo| -10 10 kHz π/4 DQPSK max carrier frequency stability |ωi| -75 75 kHz π/4 DQPSK max carrier frequency stability |ωo+ωi | -75 75 kHz 8 DPSK max carrier frequency stability |ωo| -10 10 kHz 8 DPSK max carrier frequency stability |ωi| -75 75 kHz 8 DPSK max carrier frequency stability |ωo+ωi | -75 75 kHz RMS DEVM 20 99% DEVM 30 Peak DEVM 35 RMS DEVM 13 99% DEVM 20 Peak DEVM 25 F>F0+3MHz -40 dBm F<F0-3MHz -40 dBm F=F0-3MHz -40 dBm F=F0-2MHz -20 dBm F=F0-1MHz -26 dBm F=F0+1MHz -26 dBm F=F0+2MHz -20 dBm F=F0+3MHz -40 dBm 99 π/4 DQPSK Modulation Accuracy 8 DPSK Modulation Accuracy Condition In-Band spurious emissions EDR Differential Phase Encoding (No error) 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (17 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.1 Bluetooth 5) BLE Performance General Performance Parameter Condition Min Frequency Range Typ 2402 Max Unit 2480 MHz Impedance BT_ANT Pin 50 Ohm Sensitivity level (BER≤0.1%) (Radiation performance) GFSK(1Mbps) -87 (-75) dBm -6 (-8) (6) dBm ΔF1avg 225 275 KHz ΔF2avg 230 KHz ΔF2avg/ΔF1avg 80 Transmit Power Modulation Characteristics 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (18 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.2 WLAN General Performance Parameter Condition Min 2.4G WiFi 5G WiFi Typ Max Unit 2400 2500 MHz 4900 5845 MHz Ohm Frequency Range Impedance WLAN_ANT Pin 50 1) 2.4GHz DSSS and HR/DSSS (CCK) Transmitter -. IEEE 802.11b DSSS and HR/DSSS modulation Transmitter Performance Parameter Condition Min Typ Max Unit RMS Transmit power (Radiation performance) 11Mbps CCK 13 (8) 16 19 (24) dBm RMS EVM 11Mbps CCK 35 Spectral mask, 1st Sidelobe 11Mbps CCK (fc±11MHz) -30 dBr Spectral mask, 2nd Sidelobe 11Mbps CCK (fc±22MHz) -50 dBr RF Carrier suppression Normal/Extreme 15 dBc Spurious emissions 30MHz ~ 1GHz ( RBW=100kHZ) -62 dBm 1GHz ~ 12.75GHz (RBW=1MHz) -47 dBm 1.8GHz ~ 1.9GHz (RBW=1MHz) -53 dBm 5.15GMHz ~ 5.3GHz (RBW=1MHz) -53 dBm 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (19 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.2 WLAN 2) 2.4GHz OFDM Transmitter -. IEEE 802.11g and IEEE 802.11n(HT 20/40 modes MCS0 to MCS7) OFDM modulation Transmitter Performance Parameter RMS Transmit power (Radiation performance) RMS EVM Spectral mask Center frequency leakage Spurious emissions Condition Min Typ. Max Unit OFDM, 64-QAM(3/4) (4) 12 15 (20) dBm OFDM, 64-QAM(5/6) (4) 12 15 (20) dBm OFDM, 64-QAM(3/4) -25 dB OFDM, 64-QAM(5/6) -27 dB OFDM, 64-QAM(3/4) (fc±11MHz) -20 dBr OFDM, 64-QAM(3/4) (fc±20MHz) -28 dBr OFDM, 64-QAM(3/4) (fc±30MHz) -40 dBr OFDM, 64-QAM(5/6) (fc±11MHz) HT20 -20 dBr OFDM, 64-QAM(5/6) (fc±20MHz) HT20 -28 dBr OFDM, 64-QAM(5/6) (fc±30MHz) HT20 -45 dBr Normal/Extreme -15 dB 30MHz ~ 1GHz ( RBW=100kHZ) -62 dBm 1GHz ~ 12.75GHz (RBW=1MHz) -47 dBm 1.8GHz ~ 1.9GHz (RBW=1MHz) -53 dBm 5.15GMHz ~ 5.3GHz (RBW=1MHz) -53 dBm 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (20 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.2 WLAN 3) 2.4GHz DSSS and HR/DSSS (CCK) Receiver -. IEEE 802.11b DSSS and HR/DSSS modulation Receiver Performance Parameter Rx sensitivity (Radiation performance) Maximum input level Adjacent channel rejection 1) 2) Condition Min Typ Max Unit 1Mbps DSSS1) -89(-81) dBm 2Mbps DSSS1) -84(-76) dBm 5.5Mbps CCK1) -80(-72) dBm 11Mbps CCK1) -76(-68) dBm DSSS1) -10 dBm CCK1) -10 dBm DSSS2) 35 dBr CCK2) 35 dBr 1024-byte packets, 8% PER 1024-byte packets, 8% PER, 25MHz channel separation. 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (21 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.2 WLAN 4) 2.4GHz OFDM Receiver -. IEEE 802.11g and IEEE 802.11n (HT 20/40 modes MCS0 to MCS7 800ns Guard Interval non-STBC) OFDM modulation Receiver Performance Parameter Condition Min Typ Max Unit Maximum input level3) (Radiation performance) Normal/Extreme -20 dBm 6Mbps1) -82(-74) dBm 9Mbps1) -81(-73) dBm 12Mbps1) -79(-71) dBm 18Mbps1) -77(-69) dBm 24Mbps1) -74(-68) dBm 36Mbps1) -70(-62) dBm 48Mbps1) -66(-58) dBm 54Mbps1) -65(-57) dBm MCS02) (HT 20) -82(-74) dBm MCS12) (HT 20) -79(-71) dBm MCS22) (HT 20) -77(-69) dBm MCS32) (HT 20) -74(-68) dBm MCS42) (HT 20) -70(-62) dBm MCS52) (HT 20) -66(-58) dBm MCS62) (HT 20) -65(-57) dBm MCS72) (HT 20) -64(-56) dBm Rx sensitivity (Radiation performance) (IEEE 802.11g) Rx sensitivity (Radiation performance) (IEEE 802.11n) 1) 1024-byte packets, 10% PER. 4096-byte packets, 10% PER. Applies to both HT-mixed(HT_MF) and HT-greenfield(HT-GF) format packet preamble types. 3) 1024-byte packets OFDM or 4096-byte HT packets, 10% PER. 4) 1024-byte packets, 10% PER, 25MHz channel separation. 5) 4096-byte packets, 10% PER, 25MHz channel separation. 2) 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (22 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.2 WLAN Receiver Performance Parameter Condition Min Typ Max Unit Adjacent channel rejection (IEEE 802.11g) 6Mbps4) 16 dB 9Mbps4) 15 dB 12Mbps4) 13 dB 18Mbps4) 11 dB 24Mbps4) dB 36Mbps4) dB 48Mbps4) dB 54Mbps4) -1 dB MCS05) 16 dB MCS15) 13 dB MCS25) 11 dB MCS35) dB MCS45) dB MCS55) dB MCS65) -1 dB MCS75) -2 dB Adjacent channel rejection (IEEE 802.11n) 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (23 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.2 WLAN 5) 5GHz OFDM Transmitter -. IEEE 802.11a, IEEE 802.11n (HT 20/40 modes MCS0 to MCS7) and IEEE 802.11ac OFDM modulation((VHT 20/40, VHT80 modes MCS0 to MCS9) Transmitter Performance Parameter RMS Transmit power (Radiation performance) RMS EVM Spectral mask Condition Min Typ Max Unit OFDM, 64-QAM(3/4)/(5/6) (4) 12 15 (20) dBm OFDM, 256-QAM(3/4)/(5/6) (0) 11 (16) dBm OFDM, 64-QAM(3/4) -25 dB OFDM, 64-QAM(5/6) -27 dB OFDM, 256-QAM(3/4) -30 dB OFDM, 256-QAM(5/6) -32 dB OFDM, 64-QAM(3/4) (fc±11MHz) -20 dBr OFDM, 64-QAM(3/4) (fc±20MHz) -28 dBr OFDM, 64-QAM(3/4) (fc±30MHz) -40 dBr OFDM, 64-QAM(5/6) (fc±11MHz) HT20 -20 dBr OFDM, 64-QAM(5/6) (fc±20MHz) HT20 -28 dBr OFDM, 64-QAM(5/6) (fc±30MHz) HT20 -45 dBr OFDM, 64-QAM(5/6) (fc±21MHz) HT40 -20 dBr OFDM, 64-QAM(5/6) (fc±40MHz) HT40 -28 dBr OFDM, 64-QAM(5/6) (fc±60MHz) HT40 -45 dBr OFDM, 256-QAM(5/6) (fc±11MHz) VHT20 -20 dBr OFDM, 256-QAM(5/6) (fc±20MHz) VHT20 -28 dBr OFDM, 256-QAM(5/6) (fc±30MHz) VHT20 -40 dBr 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (24 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.2 WLAN Transmitter Performance Parameter Condition Spectral mask Center frequency leakage Spurious emissions Min Typ Max Unit OFDM, 256-QAM(5/6) (fc±21MHz) VHT40 -20 dBr OFDM, 256-QAM(5/6) (fc±40MHz) VHT40 -28 dBr OFDM, 256-QAM(5/6) (fc±60MHz) VHT40 -40 dBr OFDM, 256-QAM(5/6) (fc±41MHz) VHT80 -20 dBr OFDM, 256-QAM(5/6) (fc±80MHz) VHT80 -28 dBr OFDM, 256-QAM(5/6) (fc±120MHz) VHT80 -40 dBr Normal/Extreme -15 dB 30MHz ~ 1GHz ( RBW=100kHZ) -62 dBm 1GHz ~ 12.75GHz (RBW=1MHz) -47 dBm 1.8GHz ~ 1.9GHz (RBW=1MHz) -53 dBm 5.15GMHz ~ 5.3GHz (RBW=1MHz) -53 dBm 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (25 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.2 WLAN 5) 5GHz OFDM Receiver -. IEEE 802.11a, IEEE 802.11n (HT 20/40 modes MCS0 to MCS7) and IEEE 802.11ac OFDM modulation((HT 20/40, VHT80 modes MCS0 to MCS9) Receiver Performance Parameter Condition Min Typ Max Unit Maximum input level3) (Radiation performance) Normal/Extreme -30 dBm 6Mbps1) -82(-74) dBm 9Mbps1) -81(-73) dBm 12Mbps1) -79(-71) dBm 18Mbps1) -77(-69) dBm 24Mbps1) -74(-68) dBm 36Mbps1) -70(-62) dBm 48Mbps1) -66(-58) dBm 54Mbps1) -65(-57) dBm MCS02) (HT 20) -82(-74) dBm MCS12) (HT 20) -79(-71) dBm MCS22) (HT 20) -77(-69) dBm MCS32) (HT 20) -74(-68) dBm MCS42) (HT 20) -70(-62) dBm MCS52) (HT 20) -66(-58) dBm MCS62) (HT 20) -65(-57) dBm MCS72) (HT 20) -64(-56) dBm Rx sensitivity (Radiation performance) (IEEE 802.11a) Rx sensitivity (Radiation performance) (IEEE 802.11n) 1) 1024-byte packets, 10% PER. 4096-byte packets, 10% PER. Applies to both HT-mixed(HT_MF) and HT-greenfield(HT-GF) format packet preamble types. 3) 1024-byte packets OFDM or 4096-byte HT packets, 10% PER. 4) 1024-byte packets, 10% PER, 25MHz channel separation. 5) 4096-byte packets, 10% PER, 25MHz channel separation. 2) 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (26 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.2 WLAN Receiver Performance Parameter Condition Rx sensitivity (IEEE 802.11n) Rx sensitivity (IEEE 802.11ac) Min Typ Max Unit MCS02) (HT 40) -79(-71) dBm MCS12) (HT 40) -76(-68) dBm MCS22) (HT 40) -74(-66) dBm MCS32) (HT 40) -71(-63) dBm MCS42) (HT 40) -69(-61) dBm MCS52) (HT 40) -63(-55) dBm MCS62) (HT 40) -62(-54) dBm MCS72) (HT 40) -61(-53) dBm MCS02) (VHT 20) -82(-74) dBm MCS12) (VHT 20) -79(-71) dBm MCS22) (VHT 20) -77(-69) dBm MCS32) (VHT 20) -74(-66) dBm MCS42) (VHT 20) -70(-62) dBm MCS52) (VHT 20) -66(-58) dBm MCS62) (VHT 20) -65(-57) dBm MCS72) (VHT 20) -64(-56) dBm MCS82) (VHT 20) -59(-51) dBm MCS92) (VHT 20) -57(-49) dBm 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (27 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.2 WLAN Receiver Performance Parameter Condition Rx sensitivity (IEEE 802.11ac) Rx sensitivity (IEEE 802.11ac) Min Typ Max Unit MCS02) (VHT 40) -79(-71) dBm MCS12) (VHT 40) -76(-68) dBm MCS22) (VHT 40) -74(-66) dBm MCS32) (VHT 40) -71(-63) dBm MCS42) (VHT 40) -67(-59) dBm MCS52) (VHT 40) -63(-55) dBm MCS62) (VHT 40) -62(-54) dBm MCS72) (VHT 40) -61(-53) dBm MCS82) (VHT 40) -56(-48) dBm MCS92) (VHT 40) -53(-45) dBm MCS02) (VHT 80) -76(-68) dBm MCS12) (VHT 80) -73(-65) dBm MCS22) (VHT 80) -71(-63) dBm MCS32) (VHT 80) -68(-60) dBm MCS42) (VHT 80) -64(-56) dBm MCS52) (VHT 80) -60(-52) dBm MCS62) (VHT 80) -59(-51) dBm MCS72) (VHT 80) -58(-50) dBm MCS82) (VHT 80) -53(-45) dBm MCS92) (VHT 80) -51(-43) dBm 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (28 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.2 WLAN Receiver Performance Parameter Condition Adjacent channel rejection (IEEE 802.11a) Adjacent channel rejection (IEEE 802.11n) Min Typ Max Unit 6Mbps4) 16 dB 9Mbps4) 15 dB 12Mbps4) 13 dB 18Mbps4) 11 dB 24Mbps4) dB 36Mbps4) dB 48Mbps4) dB 54Mbps4) -1 dB MCS05) 16 dB MCS15) 13 dB MCS25) 11 dB MCS35) dB MCS45) dB MCS55) dB MCS65) -1 dB MCS75) -2 dB 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (29 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.2 WLAN Receiver Performance Parameter Condition Min Typ Max Unit Adjacent channel rejection (IEEE 802.11ac) MCS05) 16 dB MCS15) 13 dB MCS25) 11 dB MCS35) dB MCS45) dB MCS55) dB MCS65) -1 dB MCS75) -2 dB MCS85) -7 dB MCS95) -9 dB 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (30 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics 1) SDIO Interface I/O pins and PCIe out of band signals(PERST_N/PME_L/CLKREQ_N) *VIO_SD= 1.8V Item Symbol Min Typ Max Unit Input high voltage VIH 1.27 Input low voltage VIL 0.58 Output high voltage@2mA VOH 1.40 Output low voltage@2mA VOL 0.45 Symbol Min Typ Max Unit Input high voltage VIH 0.625xVIO Input low voltage VIL 0.25xVIO Output high voltage@2mA VOH 0.75xVIO Output low voltage@2mA VOL 1.25xVIO *VIO_SD = 3.3V Item 2) Other Digital I/O Pins(UART/PCM/WAKE/REG_ON/STRAP and GPIOs) *VIO = 1.8V Item Symbol Min Typ Max Unit Input high voltage VIH 0.625xVIO VIO+0.1 Input low voltage VIL 0.35xVIO Output high voltage@2mA VOH 0.45xVIO Output low voltage@2mA VOL 0.45 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (31 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics *VIO = 3.3V Item Symbol Min Typ Max Unit Input high voltage VIH 2.00 VIO+0.1 Input low voltage VIL 0.8 Output high voltage@2mA VOH VIO-0.4 Output low voltage@2mA VOL 0.4 3) WLAN host interface strap selection - PCIE_EN, SDIO_DIS, SDIO_PAD PCIE_EN SDIO_DIS SDIO_PAD Mode High High High PCIe Low Low High 1.8V SDIO Low Low low 3.3V SDIO 4) Sequencing of reset and regulator control signals - Description of control signals *WL_REG_ON : Used by the PMU to power up the WLAN section. It is also OR-gated with the BT_REG_ON input to control the internal BCM88359 regulators. When this pin is high, the regulators are enabled and the WLAN section is out of reset. When this pin is low, the WLAN section is in reset. If both the BT_REG_ON and WL_REG_ON pins are low, the regulators are disabled *BT_REG_ON : Used by the PMU(OR-gated with the WL_REG_ON)to power up the internal BCM88359 regulators. If both the BT_REG_ON and WL_REG_ON pins are low, the regulators are disabled. When this pin is low and WL_REG_ON is high, the BT section is in reset 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (32 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics - Control signal timing diagrams *WLAN =ON, Bluetooth = ON *WLAN =OFF, Bluetooth = OFF 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (33 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics - Control signal timing diagrams *WLAN =ON, Bluetooth = OFF *WLAN =OFF, Bluetooth = ON 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (34 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics - Boot-Up Sequence and Reset timing 3.3V <0ms VBAT VIO <70us WL_REG_ON /BT_REG_ON <200ms VDDC <200ms < 950us (on-chip PMU) < 104ms Internal POR (Power on Reset) < 4ms After a fixed delay following internal POR and REG_ON going high, Module responds to host(address0x14) reads 27ns 8ms Internal Reference Clock Boot ROM execution starts and firmware download begins (UART and SDIO command start) 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (35 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics - PCIe Power-on Timing *Timing Parameter WL_REG_ON)Perst# Deassertion – First Config Access) 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (36 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics 5) UART characteristics -. UART physical interface is a standard, 4-wire interface(Rx, Tx, RTS, CTS) with adjustable baud rates from 9600 bps to 4Mbps. Normally the UART baud rate is set by a configuration record downloaded after reset or by automatic baud rate detection. LGIT Module supports HCI 3-wire transport(UART H5) -. UART bus timing specifications Item Min Typ Max Unit Delay time, UART_CTS_N low to UART_TXD valid 1.5 Bit periods Setup time, UART_CTS_N high before midpoint of stop bit 0.5 Bit periods Delay time, midpoint of stop bit to UART RTS_N high 0.5 Bit periods 9600 4M bps Baud rates range(default rate : 115200bps) -. UART bus timing 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (37 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics 6) PCM characteristics -. LGIT Module PCM interface can connect to linear PCM codec devices in master or slave mode. In master mode, the device generates the PCM_CLK and PCM_SYNC signals. In slave mode, these signals are provided by another master on the PCM interfaces as inputs to the devices -. Short frame sync, master mode timing diagram -. Short frame sync, master mode interface timing specifications Item Min Typ Max Unit 12 MHz PCM bit clock LOW 41 ns PCM bit clock HIGH 41 ns PCM_SYNC delay 25 ns PCM_OUT delay 25 ns PCM_IN setup ns PCM_IN hold ns Delay from rising edge of PCM_BCLK during last bit period to PCM_OUT becoming high impedance 25 ns PCM bit clock frequency 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (38 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics 6) PCM characteristics -. Short frame sync, slave mode timing diagram -. Short frame sync, slave mode interface timing specifications Item Min Typ Max Unit 12 MHz PCM bit clock LOW 41 ns PCM bit clock HIGH 41 ns PCM_SYNC setup ns PCM_SYNC hold ns PCM_OUT delay 25 ns PCM_IN setup ns PCM_IN hold ns Delay from rising edge of PCM_CLK during last bit period to PCM_OUT becoming high impedance 25 ns PCM bit clock frequency 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (39 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics 6) PCM characteristics -. Long frame sync, master mode timing diagram -. Long frame sync, master mode interface timing specifications Item Min Typ Max Unit 12 MHz PCM bit clock LOW 41 ns PCM bit clock HIGH 41 ns PCM_SYNC delay 25 ns PCM_OUT delay 25 ns PCM_IN setup ns PCM_IN hold ns Delay from rising edge of PCM_BCLK during last bit period to PCM_OUT becoming high impedance 25 ns PCM bit clock frequency 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (40 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics 6) PCM characteristics -. Long frame sync, slave mode timing diagram -. Long frame sync, slave mode interface timing specifications Item Min Typ Max Unit 12 MHz PCM bit clock LOW 41 ns PCM bit clock HIGH 41 ns PCM_SYNC setup ns PCM_SYNC hold ns PCM_OUT Delay 25 ns PCM_IN setup ns PCM_IN hold ns Delay from falling edge of PCM_BCLK or PCM_SYNC during last bit period to PCM_OUT becoming high impedance 25 ns PCM bit clock frequency 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (41 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics 7) SDIO characteristics -. RBHP-B213A support up to SDIO 3.0 specification · DS : Default speed(DS) up to 25MHz(3.3V signaling) · SDR12 : SDR up to 25MHz(1.8V signaling) · SDR25 : SDR up to 50MHz(1.8V signaling) · SDR50 : SDR up to 100MHz(1.8V signaling) · SDR104 : SDR up to 208MHz(1.8V signaling) · DDR50 : DDR up to 50MHz(1.8V signaling) -. SDIO default mode timing(min.Vih = 0.7 X VIO, max.Vil = 0.2 x VIO) 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (42 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics -. SDIO default mode bus timing parameters Item Symbol Min Typ Max Unit Freq.(data transfer mode) fPP 25 MHz Freq.(identification mode) fOD 400 KHz Clock low time tWL 10 ns Clock high time tWH 10 ns Clock rise time tTLH 10 ns Clock low time tTHL 10 ns Input setup time tISU ns Input hold time tIH ns Output delay time-data transfer mode tODLY 14 ns Output delay time-data identification mode tODLY 50 ns SDIO CLK Input : CMD, DAT(referenced to CLK) Output : CMD, DAT(referenced to CLK) 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (43 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics -. SDIO high speed mode bus timing(min.Vih = 0.7 X VIO, max.Vil = 0.2 x VIO) -. SDIO high speed mode bus timing parameters Item Symbol Min Typ Max Unit Freq.(data transfer mode) fPP 50 MHz Freq.(identification mode) fOD 400 KHz Clock low time tWL ns Clock high time tWH ns Clock rise time tTLH ns Clock low time tTHL ns SDIO CLK 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (44 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics Item Symbol Min Typ Max Unit Input setup time tISU ns Input hold time tIH ns Output delay time-data transfer mode tODLY 14 ns Output delay time-data identification mode tODLY 2.5 ns Total system capacitance(each line) CL 40 pF Input : CMD, DAT(referenced to CLK) Output : CMD, DAT(referenced to CLK) -. SDIO SDR mode clock timing Item Clock duty Symbol Min Max Unit Comments 40 50 ns SDR12 mode 20 400 ns SDR25 mode 10 ns SDR50 mode 4.8 ns SDR104 mode tCR, tCF 0.2 X tCLK ns tCR, tCF < 2.0ns(max)@100MHz CCARD = 10pF tCR, tCF < 0.96ns(max)@208MHz CCARD = 10pF 30 70 tCLK 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (45 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics -. SDIO SDR mode Device input timing Item Symbol Min Max Unit Comments SDR104 Mode tIS 1.4 ns CCARD = 10pF, VCT=0.975V tIH 0.8 ns CCARD = 5pF, VCT=0.975V SDR50 Mode tIS ns CCARD = 10pF, VCT=0.975V tIH 0.8 ns CCARD = 10pF, VCT=0.975V 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (46 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics -. SDIO SDR mode Device output timing(SDR modes up to 100MHz) Symbol Min Max Unit Comments tODLY 7.5 ns tCLK > 10ns, CL = 30pF using driver type B for SDR50 tODLY 14.0 ns tCLK > 20ns, CL = 40pF using for SDR12, SDR25 tOH 1.5 ns Hold time at the tODLY (min) CL = 15pF 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (47 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics -. SDIO SDR mode Device output timing(SDR modes 100MHz to 208MHz) Symbol Min Max Unit Comments tOP UI Card output phase ΔtOP -350 +1550 Ps Delay variation due to temp. change after tuning ΔtODW 0.60 UI ΔtODW = 2.88ns @208MHz 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (48 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics -. SDIO DDR50 mode Clock timing Item Symbol Min Max Unit Comments tCLK 20 ns DDR50 mode tCR, tCK 0.2x tCLK ns tCR, tCF < 4.0ns(max)@50MHz CCARD = 10pF Clock duty 45 55 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (49 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics -. SDIO DDR50 mode Data timing Item Symbol Min Max Unit Comments Input CMD Input Setup time tISU ns CCARD < 10pF(1CARD) Input Hold time tIH 0.8 ns CCARD < 10pF(1CARD) Output CMD Output delay time tODLY 13.7 ns CCARD < 30pF(1CARD) Output hold time tOH 1.5 Ns CCARD < 15pF(1CARD) Input DAT Input Setup time tISU2X ns CCARD < 10pF(1CARD) Input Hold time tIH2X 0.8 ns CCARD < 10pF(1CARD) Output DAT Output delay time tODLY2X 7.5 ns CCARD < 25pF(1CARD) Output holdtime tODLY2X Ns CCARD < 15pF(1CARD) 1.5 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (50 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics 8) PCI Express characteristics -. PCI Express Reference CLK Parameters Symbol Comments Min. Typ. Max Unit Baud rate BPS 2.5 Gbaud Reference clock amplitude Vref LVPECL, AC coupled 1.0 -. PCI Express Receiver Parameters Symbol Comments Min. Typ. Max Unit Differential termination ZRX-DIFF-DC Differential termination 80 100 120 Ω DC impedance ZRX-DC DC common-mode impedance 40 50 60 Ω Powered down termination(POS) ZRX-HIGH-IMP-DCPOS Power-down or RESET high Impedance 100k Ω Powered down termination(NEG) ZRX-HIGH-IMP-DCNEG Power-down or RESET high Impedance 1k Ω Input voltage VRX-DIFFp-p AC coupled, differential(p-p) 175 mV Jitter tolerance TRX-EYE Minimum receiver eye width 0.4 UI Differential return loss RLRX-DIFF Differential return loss 10.0 dB Common-mode return loss RLRX-CM Common-mode return loss dB Unexpected electrical idle enter detect threshold integration time RX-IDEL-DETDIFFENTERTIME An unexpected electrical idle must be recognized no longer than this time to signal an unexpected idle condition. 10.0 ms Signal detect threshold VRX-IDLE-DETDIFFpp Electrical idle detect threshold 65.0 175 mV 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (51 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics 8) PCI Express characteristics -. PCI Express Transmitter Parameters Symbol Comments Min. Typ. Max Unit Output voltage VTXDIFFp-p Differential p-p, programmable in 16 steps 0.8 1200 mV 20% to 80% 0.125 (2.5 GT/s) 0.15 (5 GT/s) UI UI Output voltage rise time VTX-RISE Output voltage fall time VTX-FALL 80% to 20% 0.125 (2.5 GT/s) 0.15 (5 GT/s) RX detection voltage swing VTX-RCVDETECT The amount of voltage change allowed during receiver detection. 600 mV TX AC peak common-mode voltage(5 GT/s) VTX-CMAC-PP TX AC common mode voltage (5 GT/s) 100 mV TX AC peak commonmode voltage(2.5 GT/s) VTX-CMAC-P TX AC common mode voltage (2.5 GT/s) 20.0 mV Absolute delta of DC common-model voltage during L0 and electrical idle VTX-CMDCACTIVEIDLEDELTA Absolute delta of DC common-model voltage during L0 and electrical idle. 100 mV Absolute delta of DC common-model voltage between D+ and D- VTXCM-DCLINEDELTA DC offset between D+ and D- 25.0 mV Electrical idle differential peak output voltage VTXIDLEDIFF-ACp Peak-to-peak voltage 20.0 mV 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (52 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.3 I/O characteristics 8) PCI Express characteristics Parameters Symbol Comments Min. Typ. Max Unit TX short circuit current ITXSHORT Current limit when TX output is shorted to ground. 90.0 mA DC differential TX termination ZTXDIFF-DC Low impedance defined during signaling (parameter is captured for 5.0 GHz by RLTX-DIFF) 80.0 120 Ω Differential return loss RLTXDIFF Differential return loss 10 (min) for 0.05: 1.25 GHz dB Common-mode return loss RLTX-CM Common-mode return loss 6.0 dB TX eye width TTX-EYE Minimum TX eye width 0.75 UI 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (53 / 68) (CUSTOMER P/NO : EAT63433501 ) 10. Electrical Specification 10.4 Operating Conditions 1) Recommended operation conditions Parameter Min Max Unit Operating Temperature Range -40 +85 ℃ Supply Voltage : VBATT (3.3V) 3.01) 3.6 Supply Voltage : VIO (1.8V) 1.62 1.98 2) Current consumption Parameter Average Unit Stand-by (BT & WLAN) 10 mA WLAN Continuous Rx 180 mA WLAN Continuous Tx2) 420 mA Bluetooth Connection 20 mA 3) ESD Precautions RBHP-B213A is classified as a JESD22-A114(HBM) class 1C(1kV) product. Apply ESD static handling precautions during manufacturing. 4) External 32.768KHz low-power oscillator(LPO) External 32.768KHz precision oscillator is required. Parameter LPO clock Unit Nominal input frequency 32.768 KHz Frequency accuracy ±200 ppm 200 ~ 1800 mV, p-p Single input amplitude Signal type Square-wave or sine-wave 1) The BCM88359 is functional across this range of voltages. Optimal RF performance specified in the RBHP-B213A approval sheet, however , is guaranteed only for min. 3.2V including VBAT ripple 2) MIMO condition 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (54 / 68) (CUSTOMER P/NO : EAT63433501 ) 11. Pin Configuration < Opposite (Host) Pin Map (Top View) > Position#1 Indicator20 21 40 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (55 / 68) (CUSTOMER P/NO : EAT63433501 ) 11. Pin Configuration No. Pin Name I/O Description GND BT_UART_RTS I/O Bluetooth UART request to send BT_UART_CTS I/O Bluetooth UART clear to send BT_UART_TXD I/O Bluetooth UART signal output BT_UART_RXD I/O Bluetooth UART signal input VIO BT, WLAN VDDIO supply voltage.(3.3V or 1.8V) - BT and WLAN should be same power rail GND Ground SDIO_CLK SDIO clock SDIO_CMD I/O SDIO command line 10 SDIO_DATA3 I/O SDIO data line 3 11 SDIO_DATA2 I/O SDIO data line 2 12 SDIO_DATA1 I/O SDIO data line 1 13 SDIO_DATA0 I/O SDIO data line 0 14 GND Ground 15 GND Ground Ground 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (56 / 68) (CUSTOMER P/NO : EAT63433501 ) 11. Pin Configuration No. Pin Name I/O Description 16 LPO Low power clock input (32.768KHz, 200~1800mV P-P) 17 GND Ground 18 VBAT Positive supply - Supply voltage : Typical 3.3V. 19 VBAT Positive supply - Supply voltage : Typical 3.3V. 20 VBAT Positive supply - Supply voltage : Typical 3.3V. 21 GND Ground 22 SDIO_DIS SDIO_DIABLE : Low : SDIO Enabled, High : SDIO Disabled 23 PCIE_EN PCIE_ENABLE : Low : PCIE Disabled, High : PCIE Enabled 24 GND Ground 25 BT_PCM_IN PCM data input 26 BT_PCM_OUT PCM data output 27 BT_PCM_CLK I/O PCM clock, can be master (output) or slave (input) 28 BT_PCM_SYNC I/O PCM sync signal, can be master (output) or slave (input) 29 PCIE_TD_P PCIE Transmitter differential positive 30 PCIE_TD_N PCIE Transmitter differential negative 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (57 / 68) (CUSTOMER P/NO : EAT63433501 ) 11. Pin Configuration No. Pin Name I/O Description 31 PCIE_CLK_N PCIE differential clock input negative 32 PCIE_CLK_P PCIE differential clock input positive 33 PCIE_RD_N PCIE Receiver differential negative 34 PCIE_RD_P PCIE Receiver differential positive 35 PCIE_CLKREQ PCIE clock request signal 36 PCIE_PERST_N PCIE system reset. 37 PCIE_PME_L PCIE power management event output 38 SDIO_PADVIO SDIO_PADVDDIO :If VIO_SD=1.8Vhigh, If VIO_SD=3.3Vlow 39 BT_REG_ON BT Power on Reset 40 WL_REG_ON WLAN Power on reset - Internal 200KΩ pull-down 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (58 / 68) (CUSTOMER P/NO : EAT63433501 ) 12. Reliability Test Conditions 12.1 Items related with Non-Solderability(ES96100-02) NO ITEM High Temp. Load Test Initial value measured at standard test condition. Test Conditions: 25℃ → 85℃, 100hr(Over for 1hr) Supply Voltage Condition: standard ± 5% In standard test condition, take measurements within 3hr. - No electrical problem Low Temp. Load Test Initial value measured at standard test condition. Test Conditions: 25℃ → -40℃, 100hr(Drop for 1 hr) Supply Voltage Condition: standard ± 5% In standard test condition, take measurements within 3hr. - No electrical problem High Temp. Storage Test Initial value measured at standard test condition. Test Conditions: 105℃, 168hr In standard test condition, take measurements within 3hr. - No electrical problem Low Temp. Storage Test Initial value measured at standard test condition. Test Conditions: -40±3℃, 168hr In standard test condition, take measurements within 3hr. - No electrical problem Sweep Sine Vibration Test Drop Test Condition Characteristics IInitial value measured at standard test condition. Test Conditions: 10~50Hz, 1mm p-p 2hr In standard test condition, take measurements within 3hr. Initial value measured at standard test condition. Test Conditions: - Test height: 100 cm - Test times: 10 times Drop the module onto a 10mm thickness plywood. In standard test condition, take measurements within 3hr. - No electrical problem - No mechanical damage Shock Test Initial value measured at standard test condition. Test Conditions: - Impact acceleration: 50G(m/sec2) - Impact time: 11 msec - Impact times and direction: 10 times each in 6 directions In standard test condition, take measurements within 3hr. - No mechanical damage High Temperature Durability Initial value measured at standard test condition. Test Conditions: - Test Temp.: 85℃ - Test times : 500Hr Supply Voltage Condition: - V min: until 10% of operational cycles - V normal: until 80% of operational cycles - V max: until 10% of operational cycles In standard test condition, take measurements within 3Hr - No electrical problem 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (59 / 68) (CUSTOMER P/NO : EAT63433501 ) 12. Reliability Test Conditions 12.1 Items related with Non-Solderability(ES96100-02) NO ITEM Against flux Condition Characteristics Initial value measured at standard test condition. Test Conditions -Soak 5 seconds in a I.P.A and let waiting condition for 35 seconds. After then test. - No electrical problem Initial value measured at standard test condition. Test Conditions: 3 cycle condition. Temperature (℃) 70±2 10 Temperature and Humidity Cycling 55±2 23±5 -40±2 - No electrical problem Humidity (%) 4.5 14.5 17 19 20.5 22.5 24 19 20.5 22.5 24 Time (hour) 80 60±15 4.5 14.5 17 Time (hour) In standard test condition, take measurements 2hr after. 11 Dew Condensation test Initial value measured at standard test condition. Test Conditions: 3 cycle condition. -30℃ (1 Hr) -30℃ → 25℃, 90%RH (within 1 min) 25℃, 90%RH (1 Hr) - On : 15 min / Off : 15 min In standard test condition, take measurements 2hr after. 12 High humidity and Temp. load test IInitial value measured at standard test condition. Test Conditions: 60℃, 80%, 48hr In standard test condition, take measurements within 3hr. - No electrical problem 13 Dust IInitial value measured at standard test condition. Test Conditions: JIS Z 8901, 5kg In standard test condition, take measurements within 3hr. - No electrical problem 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD - No electrical problem LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (60 / 68) (CUSTOMER P/NO : EAT63433501 ) 12. Reliability Test Conditions 12.1 Items related with Non-Solderability(ES96100-02) NO ITEM Condition Characteristics Initial value measured at standard test condition. Test Conditions: 1 hour 70 65 14 Temperature Drift Test Temperature (℃) 55 45 - No electrical problem 25 -10 -20 Take measurements sustaining each temperature. 15 Dust IInitial value measured at standard test condition. Test Conditions: JIS Z 8901, 5kg In standard test condition, take measurements within 3hr. - No electrical problem 16 Complex Environment IInitial value measured at standard test condition. Test Conditions: -20℃~60℃, 10~50Hz, 1G In standard test condition, take measurements within 3hr. - No electrical problem 17 Operation Durability IInitial value measured at standard test condition. Test Conditions: 25±5℃ 60±20%, 1500Hrs In standard test condition, take measurements within 3hr. - No electrical problem 18 ESD IInitial value measured at standard test condition. Test Conditions: ±1KV 5time 150pF/330Ω In standard test condition, take measurements within 3hr. - No electrical problem 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (61 / 68) (CUSTOMER P/NO : EAT63433501 ) 12. Reliability Test Conditions 12.2 Items related with Solderability(ES90000-04) NO ITEM High Temperature and Humidity Load Test Initial value measured at standard test condition. Test Conditions: 85±3℃, 85±5%RH, 1000hr In standard test condition, take measurements within 3hr. Thermal Shock Initial value measured at standard test condition. Test Conditions: -40℃ ( 10 min) -40℃ → 85℃, (within 10 min) 85℃ ( 10 min) 85℃ → -40℃, (within 10 min) - Test cycle : 1000 cycles - Test Times : 667 Hr In standard test condition, take measurements within 3Hr. Power and Temperature Cycling Condition Characteristics Initial value measured at standard test condition. Test Conditions: 100 cycle condition - Test Times : 100 Hr Supply Voltage Condition: standard ± 5% Power Condition: -35℃ ( 10 min) -35℃ → 75℃, (Temp. variation velocity : over 6℃/min) 75℃ ( 10 min) 75℃ → -35℃, (Temp. variation velocity : over 6℃/min) - On: 300 sec , Off: 300 sec - Whisker, No electrical problem - No Whisker, Bond strength, section inspection, electrical problem In standard test condition, take measurements within 3Hr Random Vibration test With operation Initial value measured at standard test condition. Test Conditions: - Frequency : 10 ~ 1000Hz 3 2 - Power spectrum density : 0.0296 ~ 9.63 (m/s ) /Hz - Direction : X/Y/Z, 8hr/Axis In standard test condition, take measurements 2hr after. 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (62 / 68) (CUSTOMER P/NO : EAT63433501 ) 13. Block Diagram 2.4G/5G WLAN ANT 1 5GHz FEM VBAT(3.3V) W_Tx W_Rx SW Diplexer BT_PCM ≠4 WL_REG_ON BT_REG_ON WiFi Core1 2.4GHz FEM W_Tx BT_UART ≠4 W_Rx ESD protection SW PCIE ≠9 SDIO_DIS SDIO ≠6 BCM88359 Bluetooth /5G WLAN ANT 0 5GHz FEM W_Tx W_Rx Diplexer SW WiFi Core0 W_Tx ESD protection W_Rx PCIE_EN B_Tx/Rx SDIO_PAD Bluetooth VIO LPO_CLK (32.768kH z Clock) 37.4MHz (crystal) RBHP-B213A BT/WiFi Combo Module 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (63 / 68) (CUSTOMER P/NO : EAT63433501 ) 14. Reference Circuit 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (64 / 68) (CUSTOMER P/NO : EAT63433501 ) 15. Reflow Profile Temperature 250℃ 6℃ per second maximum 3℃ per second 217℃ 200℃ Tsmax 60~150 sec Tsmin 150℃ 3℃ per second maximum 60~120 sec Ramp up Soak(flux activation) Cool down Reflow Profile Feature Pb-free Assembly Initial ramp-up rate 3℃ per second maximum Preheat Temperature minimum(Tsmin) Temperature maximum(Tsmax) Time(minimum to maximum) 150℃ 200℃ 60-120s Ramp-up rate Tsmax to TL 3℃ per second maximum Liquidus Temperature(TL) 217℃ Time above TL 60-150s Peak temperature 250℃ maximum Time within 5℃ of actual peak 10s Ramp-down rate 6℃ per second maximum 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released t [sec] DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (65 / 68) (CUSTOMER P/NO : EAT63433501 ) 16. Recommended Land Pattern 1)Top view 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (66 / 68) (CUSTOMER P/NO : EAT63433501 ) 17. Packing Information of top on BOX. (400X250X285) 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (67 / 68) (CUSTOMER P/NO : EAT63433501 ) 17. Packing Information Item ① ② EAT63433501 LGE v1.0 ⑥ Spec RBHP-B213A ⑦ ⑧ ③ ④ 2016.05.30 ⑤ 130 LotNo 6530 - 001 ⑨ ⑩ ⑪ No. Index ① POSITION (ITEM / OUTBOX) ② CUSTOMER ③ FIRMWARE VERSION (vX.X) ④ SHIPPING DATE (YYYY.MM.DD) ⑤ BARCODE (Customer P/N, Quantity) Ex) EAT63433501 130 ⑥ CUSTOMER P/N ⑦ QUANTITY ⑧ MODEL P/N ⑨ LOT NUMBER ⑩ BARCODE (Lot No.) Ex) 6530-001 ⑪ BARCODE (Model P/N, Lot No.1) Ex) RBHP-B213A.6530-001.1 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 TITLE : Specifications for approval (RBHP-B213A) REV 1.6 (68 / 68) (CUSTOMER P/NO : EAT63433501 ) 18. Ordering Information Product RB Bluetooth Module Type BT(Class2)+WLAN Host Interface PCIe Chipset Maker Broadcom Serial Number 213 213 Revision A Version 1.2 2017. 05.23. Rev1.2 Released R 1.3 2017. 06.27. Rev1.3 Released DSGD LG Innotek Co., Ltd CHKD APPD RBHP-B213A E 1.4 2017. 07.14. Rev1.4 Released V 1.5 2017. 08.10. Rev1.5 Released 1.6 2017. 09.06. Rev1.6 Released DOCUMENT NO. 6-3 (30) - 4021 FCC WARNING STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user's authority to operate the equipment. Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Modifications not expressly approved by the manufacturer could void your authority to operate the equipment under FCC rules. FCC RF Radiation Exposure Statement This equipment complies with FCC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Information for OEM integrator The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user manual of the end product. The user manual which is provided by OEM integrators for end users must include the following information in a prominent location. “To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” Label for end product must include “Contains FCC ID: BEJRBHP-B213A, IC: 2703H-RBHP-B213A" or "A RF transmitter inside, FCC ID: BEJRBHP-B213A, IC: 2703H-RBHP-B213A". IC WARNING STATEMENT This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions : (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This equipment complies with IC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Cet équipement est conforme aux limites établies par Industrie Canada en matière d'exposition aux radiofréquences dans un environnement non contrôlé. Cet appareil et son antenne ne doivent pas être colocalisés ou fonctionner en conjonction avec tout autre antenne ou émetteur. Cet équipement doit être installé et utilisé avec une distance minimale de 20cm entre le radiateur et votre corps.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Has XFA : No Language : ko-KR Tagged PDF : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Format : application/pdf Creator : Wireless Connectivity Lab. Title : SPECIFICATIONS FOR APPROVAL Create Date : 2017:09:07 11:00:29+09:00 Creator Tool : Microsoft® PowerPoint® 2010 Modify Date : 2018:01:31 18:23:50+09:00 Metadata Date : 2018:01:31 18:23:50+09:00 Producer : Microsoft® PowerPoint® 2010 Document ID : uuid:790dc014-f326-4593-9825-ab2e6ae94f7f Instance ID : uuid:a56403cc-7fb8-449e-8ad8-38e141a99d57 Page Count : 70 Author : Wireless Connectivity Lab.EXIF Metadata provided by EXIF.tools