LG Electronics USA RU50PY10 Plasma Display Panel User Manual 479Hen

Download:
Mirror Download [FCC.gov]
Document ID	475855
Application ID	+/1hJ8gFf7S+5EZVLLVJNA==
Document Description	Users Manual Part 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	267.38kB (3342259 bits)
Date Submitted	2004-10-05 00:00:00
Date Available	2004-10-05 00:00:00
Creation Date	2004-10-04 19:53:36
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2004-10-04 19:53:36
Document Title	479Hen
Document Creator	QuarkXPressª3.3E: LaserWriter 8 Z1-8.7.1
Document Author:	PSY

PLASMA TV
OWNER’S MANUAL
MODELS: DU-50PY10
DU-60PY10
TruSurround XT
TM
Please read this manual carefully and completely before
operating your TV.
Retain this manual for future reference.
Record model number and serial number of the TV in the
spaces provided below.
See the label attached on the back cover and relate this
information to your dealer if you require service.
Model Number :
Serial Number :
LG Electronics U.S.A., Inc.
Warning
Warning
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
POWER CORD POLARIZATION:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code
(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point of the cable entry as practical.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
CAUTION:
Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.
COMPLIANCE:
The responsible party for this product’s compliance is:
LG Electronics U.S.A., Inc
1000 Sylvan Avenue, Englewood Cliffs, NJ 07632
1-201-816-2000
http://www.lgusa.com
2 Plasma TV
TV Guide On Screen Notices for U.S.A.
In the United States, the TV Guide On Screen system and other related marks are registered marks of Gemstar-TV Guide
On Screen system International, Inc. and/or one of its affiliates. In Canada,TV Guide On Screen system is a registered mark
of Transcontinental Inc., and is used under license by Gemstar-TV Guide On Screen system International, Inc.
The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide On Screen system International,
Inc. and/or one of its affiliates.
The TV Guide On Screen system is protected by one or more of the following issued United States patents 6,498,895,
6,418,556, 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121.
Use of the CableCARDTM TradeMark.
“CableCARDTM is a trademark of Cable Television Laboratories, Inc.”
Digital Cable Compatibility
This digital television is capable of receiving basic analog, digital basic and digital premium cable television programming by
direct connection to a cable system providing such programming. A security card provided by your cable operator is required
to view encrypted digital programming. Certain advanced interactive digital cable services such as video-on-demand, cable
operator enhanced program the TV Guide On Screen system, and data enhanced television service may require the use of
a set top box. For more information contact your local cable operator.
Owner’s Manual 3
Safety Instructions
Safety Instructions
Important safeguards for you and your new product
Your product has been manufactured and tested with your safety in mind. However, improper use can result in electrical
shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe
the following safety points when installing and using your new product, and save them for future reference.
Observing the simple precautions discussed in this manual can help you get many years of enjoyment and safe operation
that are built into your new product.
This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.
1. Read Instructions
All the safety and operating instructions should be read
before the product is operated.
9. Attachments
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
2. Follow Instructions
All operating and use instructions should be followed.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect
it from overheating, and these openings must not be blocked
or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface.
This product should not be placed in a built-in installation
such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered
to.
3. Retain Instructions
The safety and operating instructions should be retained for
future reference.
4. Heed Warnings
All warnings on the product and in the operating instructions
should be adhered to.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
6. Water and Moisture
Do not use this product near water, for example, near a bath
tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
7. Accessories, Carts, and Stands
Do not place this product on a slippery or tilted surface, or on
an unstable cart, stand, tripod, bracket, or table. The product
may slide or fall, causing serious injury to a child or adult,
and serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the manufacturer.
8. Transporting Product
A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.
PORTABLE CART WARNING
4 Plasma TV
11. Power Sources
This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supply to your home, consult your product
dealer or local power company. For products intended to
operate from battery power, or other sources, refer to the
operating instructions.
12. Power-Cord Polarization
This product is equipped with a three-wire grounding type
plug, a plug having a third (grounding) pin. This plug will only
fit into the grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the grounding-type plug.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from
the product.
Safety Instructions
Safety Instructions continued
14. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the
product, be sure the antenna or cable system is grounded so
as to provide some protection against voltage surges and
built-up static charges. Article 810 of the National Electrical
Code (U.S.A.), ANSI/ NFPA 70 provides information with
regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
Example of Grounding According to National
Electrical Code Instructions
Ground Clamp
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Electric Service
Equipment
Grounding Conductor
(NEC Section 810-21)
Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
NEC - National Electrical Code
15. Lightning
For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage to the
product due to lightning and power-line surges.
16. Power Lines
An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power lines
or circuits as contact with them might be fatal.
17. Overloading
Do not overload wall outlets and extension cords as this can
result in a risk of fire or electric shock.
19. Servicing
Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service personnel.
20. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified technician
to restore the product to its normal operation.
e. If the product has been dropped or the cabinet has been
damaged.
f. If the product exhibits a distinct change in performance.
21. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
22. Safety Check
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to determine that the product is in proper operating condition.
23. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer. The product may slide
or fall, causing serious injury to a child or adult, and serious
damage to the product.
24. Heat
The product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
18. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
Owner’s Manual 5
Contents
Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Digital Cable Compatibility . . . . . . . . . . . . . . . . . . . . . . . . .3
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4~5
Front Surround . . . . . . . . . . . . . . . . . . . . . . . . .64
TV Speakers On/Off Setup . . . . . . . . . . . . . . . .64
Stereo/SAP Broadcasts Setup . . . . . . . . . . . . .64
Time Menu Options
Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . .65
Manual Clock Setup . . . . . . . . . . . . . . . . . . . . .65
On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .65
Sleep Timer / Auto Off . . . . . . . . . . . . . . . . . . . .66
Option Menu Features
Aspect Ratio Control . . . . . . . . . . . . . . . . . . . . .67
Cinema Mode Setup . . . . . . . . . . . . . . . . . . . . .67
Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Caption / Text . . . . . . . . . . . . . . . . . . . . . . . . . .68
Caption Option / Demo . . . . . . . . . . . . . . . . . . .69
ISM Method . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Low Power . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Lock Menu Options
Parental Lock Setup . . . . . . . . . . . . . . . . . . . . .73
CableCARDTM Function
Cable menu options . . . . . . . . . . . . . . . . . . . . .74
Scrambled channel . . . . . . . . . . . . . . . . . . . . . .74
Cable Channel List . . . . . . . . . . . . . . . . . . . . . .75
Emergency Alert Message . . . . . . . . . . . . . . . .75
Remote Control
PIP (Picture-in-Picture)/Twin Picture . . . . . . . . . ..76
Watching PIP/POP/Twin Picture . . . . . . . . . . . ..76
Selecting an Input Signal Source for PIP/Twin Picture . .76
Swapping PIP/Twin Picture . . . . . . . . . . . . . . . .76
TV Program Selection for PIP . . . . . . . . . . . . . .76
Moving the PIP sub picture . . . . . . . . . . . . . . . .77
Adjusting Main and Sub Picture Sizes for Twin Picture . .77
POP (Picture-out-of-Picture: Channel Scan) . . .77
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
EZ Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Introduction
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connection Options . . . . . . . . . . . . . . . . . . . . . .9
Remote Control Key Functions . . . . . . . . . . . . 10
Installation
Joining the TV assembly to the wall to protect the set tumbling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Installation Instructions . . . . . . . . . . . . . . . . . . . . .12
External Equipment Connections . . . . . . . . . .13~18
Antenna or Cable Connection . . . . . . . . . . .13~14
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .14
External A/V Source Setup . . . . . . . . . . . . . . . .15
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
CableCARDTM Setup . . . . . . . . . . . . . . . . . . . . .16
HDSTB Setup . . . . . . . . . . . . . . . . . . . . . . . . .16
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Monitor Out Setup . . . . . . . . . . . . . . . . . . . . . .18
Digital Audio Output . . . . . . . . . . . . . . . . . . . . .18
HDMI/DVI (VIDEO) . . . . . . . . . . . . . . . . . . . . .19~21
TV Guide On Screen Setup . . . . . . . . . . . . . .22~31
IEEE 1394 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32~36
TV Guide On Screen® System . . . . . . . . . . . . . .37~55
Operation
Screen Setup for PC mode
Adjustments for screen Position, Size, and Phase . .56
On-screen Menus Language Selection . . . . . . . . .57
Setup Menu Options
EZ Scan (Channel Search) . . . . . . . . . . . . . . . .58
Manual Scan . . . . . . . . . . . . . . . . . . . . . . . . . .58
Channel Edit . . . . . . . . . . . . . . . . . . . . . . . . . . .59
DTV Signal Strength . . . . . . . . . . . . . . . . . . . . .59
Channel Label Setup . . . . . . . . . . . . . . . . . . . .60
Main Picture Source Selection . . . . . . . . . . . . .60
Aux.Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Video Menu Options
EZ Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Manual Picture Control (Off Option) . . . . . . . . .61
Color Temperature Control . . . . . . . . . . . . . . . .61
XD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Video Preset . . . . . . . . . . . . . . . . . . . . . . . . . .62
Audio Menu Options
Audio Language . . . . . . . . . . . . . . . . . . . . . . . .63
EZ SoundRite / EZ Sound . . . . . . . . . . . . . . . . .63
Manual Sound Control (off Option) . . . . . . . . . .63
External Control Device Setup . . . . . . . . . . . . . . . .80~84
IR Codes
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85~86
Programming the Remote
Programming Codes
. . . . . . . . . . . . . . . . . . . . . .87
. . . . . . . . . . . . . . . . . . . . . . .88~89
Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .90
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .92
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95~96
Setup and Operation Checklist
Setup and Operation Checklist
(See pages 11~18 for available connection and operational setup options.)
1. Unpack TV and all accessories.
5. Turn video source equipment on.
2. Connect all external video and audio equipment.
see pages 13~ 18.
6. Select viewing source for TV.
See pages 60.
3 Install batteries in remote control.
See page 10.
7. Fine-tune source image and sound to your personal preference or as required by source.
See pages 61~ 64.
4. Turn TV on.
See page 57.
8. Additional features set up
See Contents above.
After reading this manual, keep it handy for future reference.
6 Plasma TV
Introduction
Introduction
What is a Plasma Display Panel (PDP)?
A plasma display panel is the latest display technology and the best way to achieve flat panel displays with excellent image quality
and large screen sizes that are easily viewable. The PDP can be thought of as a descendant of the neon lamp and it can be also
be viewed as a series of fluorescent lamps.
How does it work?
PDP is an array of cells, known as pixels, which are comprised of 3 sub pixels, corresponding to the colors red, green, and blue.
Gas in a plasma state is used to react with phosphors in each sub-pixel to produce colored light (red, green, or blue). These phosphors are the same types used in Cathode Ray Tube (CRT) devices such as televisions and common computer monitors.
You get the rich, dynamic colors that you expect. Each sub-pixel is individually controlled by advanced electronics to produce over
16 million different colors. All of this means that you get perfect images that are easily viewable in a display that is less than 5
inches thick.
160° - Wide angle range of vision
Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is
clear and visible to viewers anywhere in the room who can see the screen.
Wide Screen
The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater.
Multimedia
Connect your plasma display to a PC and you can use it for conferencing, games, and Internet browsing. The Picture-in-Picture
feature allows you to view your PC and video images simultaneously.
Versatile
The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs will not
fit.
The PDP Manufacturing Process: a few minute colored dots may be present on the PDP screen
The PDP (Plasma Display Panel), which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell
defects will normally occur in the PDP manufacturing process. Several tiny, minute colored dots visible on the screen should be
acceptable. This also occurs in other PDP manufacturers' products. The tiny dots appearing does not mean that this PDP is defective. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology minimizes these cell defects during the manufacture and operation of this product.
Cooling Fan Noise
In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with
cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the PDP.
The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the
operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not sufficient cause for the PDP to be exchanged or returned.
Owner’s Manual 7
Introduction
Controls
- This is a simplified representation of front panel.
Here shown may be somewhat different from your TV.
Front Panel Controls
INDEX
Switches
LED Display
on or off.
TruSurround XT
POWER
MENU
TV GUIDE TV/VIDEO
POWER
TV GUIDE TV/VIDEO MENU
VOL
VOL
CH
CH
Remote Control
Sensor
CHANNEL (E,
POWER Button
D)
Buttons
VOLUME (F,G) Buttons
MENU Button
TV/VIDEO Button
TV GUIDE Button
8 Plasma TV
Power Indicator
Illuminates orange in standby mode, Illuminates green
when the TV is turned on.
(If power isn’t turn on in red,
contact your service center.)
Introduction
Connection Options
Back Connection Panel
VIDEO
L / MONO
R AUDIO
FRONT A/V INPUT
S-VIDEO
S-VIDEO Input
A connection available to provide better picture quality than the video input.
G-LINK
Connect an
IR controller
to this jack.
Digital Audio (DVI: Digital
Visual
Interface/Component2)
Input/
Digital Audio Output
Connect digital audio from
various types of equipment.
Note: In standby mode,
these ports will not work.
HDMI /
DVI(VIDEO)
RS-232C
INPUT (CONTROL/SERVICE) PORT
Connect to the
RS-232C port
on a PC.
IEEE1394
Connect
DVHS or
MicroMV to
IEEE1394
Connector.
VIDEO Input
Connects the video signal from a
video device.
AUDIO Input
Use to connect to hear stereo sound
from an external device.
Remote Control Port
Connect your wired
remote control here.
CableCARD™
Used for
CableCARD™
received Cable
Service Provider.
CABLE Inputs
Connect cable
signals to the TV,
either directly or
through your
cable box.
DIGITAL AUDIO(OPTICAL)
DVI
AUDIO INPUT
COMPONENT2
Cable
VIDEO INPUT
ANTENNA
CABLE
AC INPUT
RGB/AUDIO
INPUT
Connect the monitor output connector from a PC to
the appropriate
input port.
DVD/DTV Input
(Component 1-2)
Connect a component
video/audio device to
these jacks.
HDMI/DVI(VIDEO)
Connect a
HDMI/DVI(Video)
signal to this jack.
Antenna Inputs
Connect antenna signals to the TV, either
directly or through
your cable box.
Monitor Output
Connect a second
TV or Monitor.
S-Video Input
Audio/Video Input
Connect S-Video out
Connect audio/video
from an S-VIDEO
output from an exterdevice to the Snal device to these
VIDEO input.
jacks.
Power Cord Socket
This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power.
- This manual explains the features available on the DU-50PY10 series TVs.
Owner’s Manual 9
Installation
Remote Control Key Functions
- When using the remote control, aim it at the remote control sensor on the TV.
LIGHT
Illuminates the remote control buttons.
TV/VIDEO
Selects: DTV, Analog, Video, Front Video,
Component 1-2, RGB-DTV (or RGB-PC),
HDMI/DVI input sources.
COMP/RGB/HDMI
Selects: Component 1-2, RGB-DTV (or RGBPC), HDMI/DVI input sources.
MODE
LIGHT
TV/VID
EO
POWER
COMP/RGB/HDMI
1394
FLASHBK
Tunes to the last channel viewed.
NUMBER buttons
DASH
Uses to enter a program number for multiple
program channels such as 2-1,2-2,etc.
MUTE
Switches the sound on or off.(Refer to p.79)
VOLUME UP/DOWN
Increases/decreases the sound level.
INFO
When you watch the TV, information displays
on top of the screen. Not available in
Component 1-2, RGB and HDMI/DVI
mode.(Refer to p.78)
SAP
Selects MTS sound: Mono, Stereo, and SAP
in Analog mode. Change the audio language
in DTV mode.
THUMBSTICK (Up/Down/Left/Right/ENTER)
Allows you to navigate the on-screen menus
and adjust the system settings to your preference.
MENU
Brings up the main menu to the screen.
Enters or exits a Panel Menu in the TV Guide On
Screen system.
TV GUIDE
Brings up the TV Guide On Screen system to
the screen.
FLASHBK
MUTE
SURF
PGUP
VOL
CH
PGDN
SAP
RATIO
INFO
CC
ENTER
MENU
EXIT
TV GUIDE TIMER
PLAY
REW
PAUSE
STOP
RECORD
FF
DAY -
DAY +
SKIP
PIP
PIPCH-
PIPCH+
PIPINPUT
VIDEO
SOUND
SIGNAL
SWAP
ADJUST
FREEZE
ZOOM
VIDEO
Adjusts the factory preset picture
depending on the viewing environment.
ADJUST
Adjusts screen position, size, and
phase in PC mode.
SOUND
Selects the sound appropriate
for the program's character.
SIGNAL
Displays the digital signal strength.
FREEZE
Freezes the currently-viewed picture. Main picture is frozen in PIP/Twin picture mode.
Installing Batteries
• Open the battery compartment cover on the back side and install the batteries
matching correct polarity (+ with +, - with -).
• Install two 1.5V AA batteries. Don’t mix old or used batteries with new ones.
Replace cover.
10 Plasma TV
MODE
Selects the remote operating mode: TV,
VCR, DVD, CABLE, HDSTB or AUDIO.
Select other operating modes, for the
remote to operate external devices.
POWER
Turns your TV or any other programmed
equipment on or off, depending on mode.
1394 (Refer to p.32-36)
SURF
Use to scroll the Surf channel.
CHANNEL UP/DOWN
Selects available channels found with EZ
scan.
PAGE UP/PAGE DOWN
Moves from one full set of screen information to the next one.
RATIO
Changes the aspect ratio.
CC
Select a closed caption:
Off, CC1~4, Text1~4.
EXIT
Clears all on-screen displays and returns to
TV viewing from any menu.
TIMER
Lets you select the amount of time before
your TV turns itself off automatically.
VCR/DVD BUTTONS
Control some video cassette recorders or
DVD player. ("RECORD" button is not available for DVD player.)
Selects the frequency setting in the recording: Once, Regularly, Weekly,
Off.("RECORD" button only)
DAY+/DAYMoves forward or backward in 24 hour
increments in the Listings Grid.
PIP
Switches between PIP, POP (Picture-out-ofPicture) and Twin picture modes.
Switches the video window locking or
unlocking in the Listings Grid.
PIPCH-/PIPCH+
Changes to next higher/lower PIP channel.
PIP INPUT
Selects the input source for the sub picture.
SWAP
Exchanges the main/sub images in
PIP/Twin picture mode.
ZOOM
Enlarges the main picture size.
Installation
Installation
Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer
where you purchased the product.
1.5V
1.5V
Owner’s Manual
Batteries
MODE
LIGHT
TV/VIDEO
Power Cord
75Ω Round Cable
POWER
COMP/RGB/DVI TIMER
FLASHBK
MUTE
SURF
VOL
CH
RATIO
SAP
INFO
CC
OK
EXIT
MENU
PLAY
REW
SOUND
VIDEO
PAUSE
STOP RECORD
FF
SKIP
PIP
PIPCH-
PIPCH+
PIPINPUT
FREEZE
ZOOM
SIGNAL
SWAP
ADJUST
4-TV bracket bolts(50”)
2-TV bracket bolts(60”)
2-TV brackets
2-Wall brackets
G-LINK Cable
Joining the TV assembly to the wall to protect the set tumbling
- Secure the TV assembly by joining it to a wall by using the TV/Wall brackets.
• After the set must be mounted on the desk top, install the
TV brackets on the TV as shown.
Install the TV brackets on the TV as shown.
Insert the 2 bolts and tighten securely, in the upper holes
on the bracket.
Install the wall brackets on the wall with 4 bolts*, (not
supplied with the product), as shown.
Match the height of the TV brackets and the wall brackets.
Check to be sure the brackets are tightened securely.
• Secure the TV assembly to the wall with strong strings
or wound wire cables, (not supplied with the product), as
shown.
Owner’s Manual 11
Installation
Installation Instructions
• The TV can be installed in various ways such as on a wall, or on a desktop etc.
• The TV is designed to be mounted horizontally. The speakers shown are optional.
GROUNDING
Power
Supply
Ensure that you connect the grounding / earth wire to prevent possible
electric shock. If grounding methods are not possible, have a qualified
electrician install a separate circuit breaker. Do not try to ground the
unit by connecting it to telephone wires, lightening rods, or gas pipes.
Short-circuit
Breaker
Desktop Pedestal Installation
Wall Mount: Horizontal installation
For proper ventilation, allow a clearance of 4” on each
side and 2” from the wall. Detailed installation instructions are available from your dealer, see the optional
Wall Mounting Bracket Installation and Setup The TV
guide on screen system.
For proper ventilation, allow a clearance of 4” on each
side and the top, 2.36” on the bottom, and 2” from the
wall. Detailed installation instructions are included in
the optional Desktop Stand Installation and Setup The
tv guide on screen system available from your dealer.
2 inches
4 inches
4 inches
4 inches
4 inches
4 inches
12 Plasma TV
4 inches
2 inches
4 inches
2.36 inches
Installation
External Equipment Connections
Antenna or Cable Connection
1. Analog and Digital TV signals provided on antenna
- Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections
- For optimum picture quality, adjust antenna direction if needed.
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
ANTENNA
CABLE
Wall Antenna
Socket
Bronze Wire
RF Coaxial Wire (75 ohm)
VHF Antenna
Turn clockwise to tighten.
UHF Antenna
Bronze Wire
Outdoor
Antenna
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Be careful not to bend the bronze wire when
connecting the antenna.
2. Analog and Digital TV signals provided on cable
Cable
Cable TV Wall
Jack
ANTENNA
CABLE
RF Coaxial Wire (75 ohm)
Bronze Wire
Owner’s Manual 13
Installation
3. Analog and Digital TV signals provided on cable and antenna
Antenna
Bronze Wire
RF Coaxial Wire (75 ohm)
Cable
ANTENNA
Cable TV Wall
Jack
CABLE
Turn clockwise to tighten.
RF Coaxial Wire (75 ohm)
• In a poor signal area to improve picture quality, purchase
and install a signal amplifier.
• If the antenna needs to be split for two TV’s, install a “2Way Signal Splitter” in the connections.
• If the antenna is not installed properly, contact your dealer for assistance.
Signal
Amplifier
Note: The TV will let you know when the analog, cable, and digital channel scans are complete.
VCR Setup
- To avoid picture noise (interference), leave an adequate distance between the VCR and TV
- Use the ISM Method (on the Option menu) feature to avoid having a fixed image remain on the screen for a long period of time.
If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen.
Connection Option 1
Set VCR output switch to 3 or 4 and then tune
TV to the same channel number.
HDMI /
DVI(VIDEO)
AUDIO INPUT
DIGITAL AUDIO(OPTICAL)
COMPONENT2
DVI
Cable
VIDEO INPUT
ANTENNA
Connection Option 2
1. Connect the audio and video cables from the
VCR's output jacks to the TV input jacks, as
shown in the figure.
When connecting the TV to VCR, match the
jack colors (Video = yellow, Audio Left = white,
and Audio Right = red).
If you connect an S-VIDEO output from VCR to
the S-VIDEO input, the picture quality is
improved; compared to connecting a regular
VCR to the Video input.
2. Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner’s
manual.)
3. Select the input source with using the
TV/VIDEO button on the remote control. (If
connected to A/V INPUT , select Video input
source)
Do not connect to both Video and
S-Video at the same time.
14 Plasma TV
CABLE
AC INPUT
ANT OUT
ANT IN
S-VIDEO
VCR Rear
OUT
OUTPUT
SWITCH
IN
(R) AUDIO (L)
VIDEO
External A/V Source Setup
HDMI /
DVI(VIDEO)
How to connect
DIGITAL AUDIO(OPTICAL)
Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the
figure.
When connecting the TV to external equipment, match the
jack colors (Video = yellow, Audio Left = white, and Audio
Right = red).
Cable
COMPONENT2
DVI
AUDIO INPUT
VIDEO INPUT
ANTENNA
CABLE
AC INPUT
How to use
1. Select the input source with using the TV/VIDEO button on
the remote control. (If connected to A/V INPUT , select
Video input source).
2. Operate the corresponding external equipment. Refer to
external equipment operating the tv guide on screen system.
Camcorder
Video Game Set
DVD Setup
HDMI /
DVI(VIDEO)
AUDIO
VIDEO
DIGITAL AUDIO(OPTICAL)
COMPONENT2
DVI
AUDIO INPUT
Cable
VIDEO INPUT
ANTENNA
CABLE
AC INPUT
DVD
or
or
DIGITAL AUDIO
OPTICAL
(R) AUDIO (L)
S-VIDEO
(R) AUDIO (L)
How to connect
1. Connect the DVD video outputs (Y, PB, PR) to the COMPONENT (Y, PB, PR) INPUT jacks on the TV and connect the DVD
audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure.
2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the TV and connect the DVD audio outputs
to the AUDIO INPUT jacks on the TV, as shown in the figure.
Note: If your DVD player does not have component video output, use S-Video.
How to use
1. Turn on the DVD player, insert a DVD.
2. Use the TV/VIDEO or COMP/RGB/HDMI button on the remote control to select Component 1 or Component 2. (If connected
to S-VIDEO, select the Video or Front Video external input source.)
3. Refer to the DVD player's manual for operating instructions.
• Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports
on the TV
PB
Video output ports
on DVD player
Pr
Pb
B-Y R-Y
Cr
Cb
PB PR
PR
Notes:
• Digital Audio will not work for Component 1 input source.
• Digital Audio operation has priority if Digital Audio and AUDIO L/R
are connected at the same time.
Owner’s Manual 15
Installation
TM
CableCARDTM
Setup
How to use
Insert the CableCARDTM received from Cable Service provider to
CableCARDTM slot of TV back panel.
If Host or CableCARDTM does not display on the screen, contact with Cable
service provider by phone.
Cable
ANTENNA
CABLE
Note :
• CableCARDTM has the types of Motorola, Scientific Atlanta, SCM etc..
These 3 types of CableCARDTM can be used for this PLASMA TV.
AC INPUT
Caution: When removing the CableCARDTM, do not
fall it as this may cause impact to the
CableCARDTM.
HDSTB Setup
- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital
signals from a digital set-top box or other digital external device, refer to the figure as shown below.
- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i).
HDMI /
DVI(VIDEO)
DIGITAL AUDIO(OPTICAL)
COMPONENT2
DVI
AUDIO INPUT
Cable
VIDEO INPUT
ANTENNA
CABLE
AC INPUT
or
or
RGB-DTV OUTPUT
or
(R) AUDIO (L)
(R) AUDIO (L)
DIGITAL AUDIO
OPTICAL
or
DVI-DTV OUTPUT HDMI-DTV OUTPUT
DIGITAL AUDIO
OPTICAL
(R) AUDIO (L)
Digital Set-top Box
How to connect
Use the TV’s COMPONENT (Y, PB, PR) INPUT, RGB or HDMI/DVI jack
for video connections, depending on your set-top box connector. Then,
make the corresponding audio connections.
How to use
1. Turn on the digital set-top box. (Refer to the owner’s manual for the
digital set-top box.)
2. Use TV/VIDEO or COMP/RGB/HDMI on the remote control to select
Component 1, Component 2, RGB-DTV, or HDMI/DVI source.
16 Plasma TV
Signal
480i
480p
720p
1080i
Component 1/2
Yes
Yes
Yes
Yes
RGB-DTV,HDMI/DVI
No
Yes
Yes
Yes
Installation
PC Setup
- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
- The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card, change the screen scanning rate for the graphic
card accordingly.
HDMI /
DVI(VIDEO)
AUDIO INPUT
DIGITAL AUDIO(OPTICAL)
DVI
COMPONENT2
Cable
VIDEO INPUT
ANTENNA
CABLE
AC INPUT
How to connect
1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz.
2. Use the TV’s RGB INPUT or HDMI/DVI (Digital Visual Interface) INPUT port for video connections, depending on your PC connector.
• If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of either RGB INPUT
or DVI INPUT to display the PC on the TV.
• If the graphic card on the PC does output analog and digital RGB simultaneously, set the TV to either RGB or HDMI/DVI; (the
other mode is set to Plug and Play automatically by the TV.)
3. Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required.
How to use
1. Turn on the PC and the TV.
2. Turn on the display by pressing the POWER button on the TV's remote control.
3. Select RGB-PC or HDMI/DVI input source in main input option of SETUP menu. (Refer to P.59)
4. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC
mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the
brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed,
change the PC graphic card or consult the manufacturer of the PC graphic card.
Notes:
• Depending on the graphics card, DOS mode may not work if you use a HDMI to DVI cable.
• Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently
imprinted on the screen. Use the Orbiter screen saver when possible.
• The synchronization input form for Horizontal and Vertical frequencies is separate.
Monitor Display Specifications (RGB-PC )
Resolution
640x350
720x400
640x480
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
31.468
70.09
37.861
85.08
31.469
70.08
37.927
Resolution
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
56.25
35.156
37.879
60.31
48.077
72.18
85.03
46.875
75.00
31.469
59.94
53.674
85.06
37.861
72.80
48.363
60.00
37.500
75.00
56.476
70.06
43.269
85.00
60.023
75.02
800x600
1024x768
Owner’s Manual 17
Installation
Monitor Display Specifications (HDMI/DVI Mode)
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
Resolution
31.469
640x480
37.861
800x600
Resolution
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
59.94
48.363
60.00
72.80
56.476
70.06
60.023
75.02
37.500
75.00
35.156
56.25
37.879
60.31
48.077
72.18
46.875
75.00
1024x768
Monitor Out Setup
HDMI /
DVI(VIDEO)
DIGITAL AUDIO(OPTICAL)
DVI
AUDIO INPUT
Cable
COMPONENT2
VIDEO INPUT
The TV has a special signal output capability which allows you to
hook up a second TV or monitor.
ANTENNA
Connect the second TV or monitor to the TV’s MONITOR OUTPUT.
See the Operating Manual of the second TV or monitor for further
details regarding that device’s input settings.
Note
• Component, RGB-PC/RGB-DTV, HDMI/DVI, DTV input sources
cannot be used for Monitor out.
S-VIDEO
IN
(R) AUDIO (L)
VIDEO
Digital Audio Output
Send the TV’s audio to external audio equipment (stereo system) via
the Digital Audio Output (Optical) port.
HDMI /
DVI(VIDEO)
How to connect
1. Connect one end of an optical cable to the TV Digital Audio
(Optical) Output port.
2. Connect the other end of the optical cable to the digital audio (optical) input on the audio equipment.
3. Set the “ TV Speaker option - Off” in the AUDIO menu. Refer to
page 64.
See the external audio equipment instruction manual for operation.
Caution: Do not look into the optical output port.
Looking at the laser beam may damage
your vision.
18 Plasma TV
DIGITAL AUDIO(OPTICAL)
DVI
AUDIO INPUT
COMPONENT2
Cable
VIDEO INPUT
ANTENNA
HDMI
HDMI/DVI (VIDEO)
-HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC."
-This TV SET can receive the High-Definition Multimedia Interface(HDMI) or Input of Digital Visual Interface(DVI).
-This TV SET supports HDCP(High-bandwidth Digital Contents Protection) Protocol for TV SET(480p, 720p, 1080i) modes.
-When you Connect with HDMI/DVI Source Devices (DVD Player or Set Top Box or PC) supporting Auto HDMI/DVI function, automatically, support Plug & Play and then set the HDMI/DVI Source Devices(1280 x 720p). After reading in HDMI/DVI Source
Devices using Display Data Channel(DDC) Protocol, EDID stored in TV SET is used . If HDMI/DVI Source Devices not supported Auto HDMI/DVI is been, the Resolution is setted, manually.
- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1280 x 720p.
- To get the best picture quality, adjust the PC graphics card to 1024 x 768, 60Hz.
- When Source Devices have DVI Output Connector, you must connect audio with separated cable.(Refer to )
How to connect
1. When Source Devices(DVD Player or Set Top Box) support HDMI.
- If Source Devices have HDMI Output Connector, Source Devices connect to DTV with HDMI Cable .(not supplied with the product).
- If Source Devices support Auto HDMI, automatically, Source Devices divert output resolution in 1280x720p. But if not, resolution
divert Manually Setting for reference Manual of Source Devices.
- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1280 x 720p.
- Because HDMI sends Digital Video and Audio with one cable, need not especial Audio Cable for using HDMI Cable.
2. When Source Devices(DVD Player or Set Top Box) supports DVI.
- If Source Devices have DVI Output Connector, Source Devices connect to DTV with HDMI to DVI Cable (not supplied with the
product).
- If Source Devices support Auto DVI, automatically, Source Devices divert output resolution in 1280x720p. But if not, resolution
divert Manually Setting for reference Manual of Source Devices.
- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1280 x 720p.
- In this case, Audio use other cable. When Source Devices have Fiber Optic Digital Audio Output Connector, Digital Audio DVI
Input(DVI) of DTV connect to Fiber Optic Digital Audio Cable (not supplied with the product) or when Source Devices have Analog
Audio Output Connector, RGB/DVI Audio Input of DTV connect to Audio Cable (not supplied with the product). And then you can
listen to normal Audio.
3. When PC supports DVI.
- If PC have DVI Output Connector, Source Devices connect to DTV with HDMI to DVI Cable (not supplied with the product).
- To get the best picture quality, adjust the PC graphics card to 1024 x 768, 60Hz.
- Use the DTV’s HDMI/DVI(VIDEO) for video connections, depending on your PC connector.
- If the graphics card on the PC does not output analog RGB and DVI simultaneously, connect only one of either RGB Input or
HDMI/DVI Input to display the PC on the DTV.
- If he graphics card on the PC does output analog RGB and DVI simultaneously, set the DTV to either RGB Input or HDMI/DVI
Input;(the other mode is set to Plug and Play automatically by the DTV.)
- Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required.
- In this case, Audio use other cable. When PC (or sound card of PC) have Fiber Optic Digital Audio Output Connector, Digital Audio
DVI Input(DVI) of DTV connect to Fiber Optic Digital Audio Cable (not supplied with the product) or when PC (or sound card of
PC) have Analog Audio Output Connector, RGB/DVI Audio Input of DTV connect to Analog Audio Cable (not supplied with the
product). And then you can listen to normal Audio.
Owner’s Manual 19
HDMI
Reference
Cable sample
HDMI Cable
(not supplied with the product)
HDMI to DVI Cable
(not supplied with the product)
Fiber Optic Digital Audio Cable
(not supplied with the product)
Analog Audio Cable(RCA type)
(not supplied with the product)
Analog Audio Cable(Stereo to RCA type)
(not supplied with the product)
20 Plasma TV
HDMI
How to use
1. Connect the HDMI/DVI Source Devices(DVD Player or Set Top Box or PC) and the TV SET.
2. Turn on the display by pressing the POWER button on the TV SET and HDMI/DVI Source Devices remote control.
3. Select HDMI/DVI Input source in Main Input option of SETUP menu.(Refer to P.60)
4. Check the image on your TV SET. There may be noise associated with the resolution, vertical pattern, contrast or brightness in
HDMI/DVI Source Devices. If noise is present, change the HDMI/DVI Source Devices to another resolution, change the refresh
rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphics card can
not changed, change the PC graphics card or consult the manufacturer of the PC graphics card.
Notes:
- Depending on the graphics card, DOS mode may not work if you use a HDMI to DVI Cable.
- Avoid keeping a fixed image on the TV SET screen for a long period of time. The fixed image may become permanently imprinted on the screen. Use the Orbiter screen saver when possible.
- When Source Devices connected HDMI/DVI Input, output PC Resolution(VGA, SVGA, XGA), Position, Size may not fit to
Screen. As shown the lower picture, press the Adjust button to adjust the screen Position of TV SET and contact an PC graphics card service center.
- When Source Devices connected HDMI/DVI Input output TV SET Resolution(480p, 720p, 1080i), TV SET Display fit EIA/CEA861-B Specification to Screen. If not, refer to the Manual of HDMI/DVI Source Devices or contact your service center.
- In case HDMI/DVI Source Devices is not connected Cable or poor cable connection, "NO SIGNAL" OSD display in HDMI/DVI
Input. And In case of, Video Resolution not supported TV SET output in HDMI/DVI Source Devices, "INVALID FORMAT" OSD
display. Refer to the Manual of HDMI/DVI Source Devices or contact your service center.
POSITION
SIZE
PHASE
RESET
Adjust Close
In This Mode, the Supported TV SET Resolution Specification
1920 x 1080 I @ 59.94Hz / 60Hz, 16:9
1280 x 720 P @ 59.94Hz / 60Hz, 16:9(preferred format)
704 x 480 P @ 59.94Hz / 60Hz, 16:9
704 x 480 P @ 59.94Hz / 60Hz, 4:3
In This Mode, the Supported PC Resolution Specification
640 x 480 @ 60Hz
640 x 480 @ 72Hz
640 x 480 @ 75Hz
800 x 600 @ 56Hz
800 x 600 @ 60Hz
800 x 600 @ 72Hz
800 x 600 @ 75Hz
1024 x 768 @ 60Hz(preferred format)
1024 x 768 @ 70Hz
1024 x 768 @ 75Hz
Owner’s Manual 21
Installation
TV Guide On Screen Setup
- The TV Guide On Screen system uses Setup information to provide you with show listings and lineups in your area—which are
updated several times a day.
- Once you set up the TV according to manufacturer’s instructions, you are ready to set up the TV Guide On Screen system.
Note: The TV Guide On Screen System interactive program guide provides listings for cable-ready, cable box, and digital cable
services as well as over-the-air broadcast. It does not provide listings for satellite services.
How to connect VCR and Cable Box
1. Antenna Service
HDMI /
DVI(VIDEO)
DIGITAL AUDIO(OPTICAL)
COMPONENT2
DVI
AUDIO INPUT
Cable
VIDEO INPUT
ANTENNA
CABLE
AC INPUT
ANT OUT
ANT IN
OUT
OUTPUT
SWITCH
IN
(R) AUDIO (L)
VIDEO
S-VIDEO
VCR Rear
VCR Front
2. Cable Service without a Cable Box
HDMI /
DVI(VIDEO)
AUDIO INPUT
DIGITAL AUDIO(OPTICAL)
DVI
COMPONENT2
Cable
VIDEO INPUT
ANTENNA
CABLE
AC INPUT
ANT OUT
ANT IN
OUT
OUTPUT
SWITCH
IN
(R) AUDIO (L)
S-VIDEO
VCR Front
22 Plasma TV
VCR Rear
VIDEO
Installation
3. Cable Service with a Cable Box
Cable
CABLE
ANTENNA
AC INPUT
or
ANT OUT
ANT IN
OUT
OUTPUT
SWITCH
IN
VCR Front
(R) AUDIO (L)
VIDEO
VCR Rear
S-VIDEO
Cable Box Front
(R) AUDIO (L)
OUTPUT
SWITCH
RF
VIDEO
TV
Cable Box Rear
VCR
Cable
4. Antenna and Cable Service without a Cable Box
Cable
CABLE
ANTENNA
AC
INPUT
AC INPUT
ANT OUT
VCR Front
ANT IN
OUT
OUTPUT
SWITCH
IN
(R) AUDIO (L)
VIDEO
VCR Rear
S-VIDEO
5. Antenna and Cable Service with a Cable Box
Cable
CABLE
ANTENNA
AC INPUT
or
VCR Front
ANT OUT
ANT IN
OUT
OUTPUT
SWITCH
IN
(R) AUDIO (L)
VIDEO
VCR Rear
S-VIDEO
Cable Box Front
(R) AUDIO (L)
OUTPUT
SWITCH
RF
Cable
TV
VIDEO
Cable Box Rear
VCR
Owner’s Manual 23
Installation
Note:
• The G-LINK cable is necessary for the TV Guide On Screen system to work with your Cable Box and VCR. See Page
22~23 for G-LINK connection instructions.
1.Reminder Screen
The TV Guide On Screen system's Reminder Screen appears:
-- after initial TV set up
-- if you power Off the TV and then power it back On
To make a selection, use the
and press ENTER.
button to highlight to an option,
• "Set up TV Guide On Screen now," displays the Welcome Screen.
Press ENTER to begin Setup.
• "Remind me to set up later" returns you to watching TV.
• "Don't remind me again" returns you to watching TV and stops the
reminder screen from appearing upon power On.
2.Welcome Screen
The TV Guide On Screen system's Welcome Screen appears:
-- by pressing the TV Guide key
-- when you power On your TV if you previously skipped "Set up TV
Guide On Screen now" on the Reminder Screen.
The Welcome Screen highlights features of the TV Guide On Screen
system.
Press ENTER to begin Setup.
How to use
1. Screen 1: Country
•This screen asks you the location of your TV.
•Use the D / E button to highlight a country.
•Press ENTER to display Screen 2.
24 Plasma TV
Installation
2. Screen 2: Enter Zip or Postal Code
Option 1
•If you selected USA in Screen 1, you see the ZIP Code screen.
•You input numbers by either pressing the number keys on the remote
or using the D / E button to display a number, and then the F / G button to move to another field.
•Press ENTER to display Screen 3.
Option 2
•If you selected Canada in Screen 1, you see the Postal Code screen.
•You input characters by using the
button, and then the
F /G
but-
ton to move to another field.
•Press ENTER to display Screen 3.
3. Screen 3: Do you have Cable?
•If you select Yes, you see Screen 4.
•If you select No, you see Screen 12.
4. Screen 4: Do you have a Cable Box?
•If you select Yes, you see Screen 5.
•If you select No, you see Screen 12.
Owner’s Manual 25
Installation
5. Screen 5: Which TV input is the cable box plugged into?
•If you select Cable, you see Screen 6.
•If you make any other choice, you see Screen 7 .
6. Screen 6: Cable Box Tuning Channel
•Select the channel used for the cable box.
•Press ENTER to display Screen 7.
7. Screen 7: Cable Box Configuration Diagram
•The diagram shows the correct way to install the G-LINK Cable from
the back of the device to the cable box.
Make sure the G-LINK Cable is properly installed.
•Press ENTER to display Screen 8.
26 Plasma TV
Installation
8. Screen 8: Cable Box Brand Name
•Use the D / E button to select a cable box brand.
•Press ENTER to display Screen 9.
9. Screen 9: Cable Box Preparation
Follow the on-screen instructions, and press ENTER to display
Screen 10.
10. Screen 10: Cable Box Code Testing
When testing is done, Screen 11 displays automatically.
11. Screen 11: Cable Box Tuned to Channel 9?
If you select Yes, you see Screen 12.
If you select No, a different code is tested in Screen 10.
Note:
•Many Cable Boxes require testing more than one code.
If you select Test this code again, the same code is tested again
in Screen 10.
Owner’s Manual 27
Installation
12. Screen 12: Do you have an antenna connected?
•If you select Yes, you see Screen 13.
Note:
•If you selected No in Screen 3 then you must
select Yes in this screen to receive a channel
lineup and listings.
•If you select No, you see Screen 13.
13. Screen 13: Are your basic settings correct?
•If you select Yes, you see Screen 14.
•If you select No, you see Screen 1.
14. Screen 14: Congratulations
•Press ENTER to display Screen 15.
28 Plasma TV
Installation
15. Screen 15: Is a VCR Connected?
•If you select Yes, you see Screen 16.
•If you select No, you see Screen 21.
16. Screen 16: VCR Configuration Diagram
•This screen shows the correct way to install the G-LINK Cable from
the back of the TV to the Recording device.
Make sure the G-LINK Cable is properly installed.
•Press ENTER, and you see Screen 17.
17. Screen 17: VCR Brand Name
•Use the D / E button to select the brand of the recording device.
•Press ENTER, and you see Screen 18.
Owner’s Manual 29
Installation
18. Screen 18: VCR Preparation
Follow the on-screen instructions, and press ENTER to display Screen
19.
19. Screen 19: VCR Code Testing
When testing is done, Screen 20 displays automatically.
20. Screen 20: VCR Tuned to Channel 9?
•If you select Yes, you see Screen 21.
•If you select No, a different code is tested in Screen 19.
Note : Many VCRs require testing more than one code.
•If you select Test this code again, the same code is tested again in
Screen 19.
30 Plasma TV
Installation
21. Screen 21: Confirming Your Settings
Verify the Setup information is correct.
If it is, select Yes, end setup, and you see Screen 22.
If it is not, select No, repeat setup process, and you see Screen 1.
22. Screen 22: Congratulations
•You have successfully completed Setup!
•Press ENTER and you see Screen 23.
23. Screen 23: Helpful Information
•This screen tells you valuable information on using your Guide.
•Press ENTER to watch TV.
Notes:
The TV Guide On Screen system receives program listings data through your cable or over-the-air video signal. In order to
receive regular program listings, please remember to do the following:
1. Turn OFF your TV when it is not in use. (Do not unplug the power cord.)
2. If you have a Cable box connected, leave it ON.
3. If you have a VCR connected, turn it OFF when not in use. (Do not unplug the power cord.)
4. If you have more than one Cable system in your area, you may be prompted to select which Cable system’s program data to
download. If so prompted, please follow the on-screen instructions.
Owner’s Manual 31
IEEE 1394
IEEE 1394 Functions
IEEE 1394
- It's available to communicate to either direction and you can give and take a image, sound, or each control command
with one cable.
- Only use the DVHS and MicroMV Camcorder to work the 1394.
How to connect the 1394
•To work the 1394, this 3 methods can used.
1. When connecting the DVHS or the MicroMV Camcorder, as shown in the (a) or (b) figure, press the 1394 button to show the
control panel.
(a) TV
DVHS
(b) TV

MicroMV Camcorder



TV GUIDE TV/VIDEO
POWER
MENU
VOL
CH
TV GUIDE TV/VIDEO
POWER
MENU
VOL
CH


2. When connecting the DVHS and the MicroMV Camcorder, as shown in the (c) figure, press the 1394 button to show the contents panel and then select the DVHS or the MicroMV Camcorder to show the control panel.
(c) TV
DVHS + MicroMV Camcorder


TV GUIDE TV/VIDEO
POWER
MENU
VOL
CH



When connecting the 1394 and then playing, you must use the original DVHS tape. If not, it may be
occurred the errors.
32 Plasma TV
IEEE 1394
IEEE 1394 functions continued
DVHS
How to play the DVHS
1. Connect the IEEE 1394 jack of the TV to the IEEE 1394
jack of the DVHS with IEEE 1394 Cable.
2. When watching the TV, press the 1394 button.
• Show the control panel of DVHS.

Panasonic
NV-DH2
DVHS
VSTOP
+0:00:06
POWER
TV GUIDE TV/VIDEO
POWER
MENU
VOL
FF
CH
GG
FF
0:00
GG

* Supported DVHS List
• The control panel of DVHS
-Depending on the connected equipment, marked control panel may differ.
VICTOR(HM-DH35000U)
JVC(HM-DH30000U)
1. DVHS Company
JVC(HM-DH40000U)
2. DVHS Model
MITSUBISHI(HS-HD1100U)
MITSUBISHI(HS-HD2000U)
Hitachi(DT-DR20000)
Hitachi(DT-DRX100)
PANASONIC(NV-DH1)
PANASONIC(NV-DH2)
PANASONIC(NV-DHE20)
TOSHIBA(A-HD2000)
Panasonic
NV-DH2
DVHS
VSTOP
+0:00:06
3. Connected Equipment to the 1394
POWER
FF
GG
FF
0:00
GG
4. DVHS Operating Status
5. Power On/Off
6. Tape Status
• Tape shape Icon - Tape in or not
• Lock shape Icon - Use or not use
7. DVHS Play Time
8. Initializing Play Time
9. DVHS Play, Pause, Stop, Search or Skip
(Notes:
• Skip- This function is for a fast search.
It searches the program’s start
point and then plays.
On skipping, Search (GG,
FF
), Pause
( ) and Play (G) are displayed on the
Control Panel.
In some models, it’s not available to
operate the Skipping (
FF
GG
function.
Owner’s Manual 33
IEEE 1394
IEEE 1394 functions continued
MicroMV Camcorder
How to play the MicroMV Camcorder
1. Connect the IEEE 1394 jack of the TV to the IEEE 1394
jack of the MicroMV Camcorder with IEEE 1394 Cable.
2. When watching the TV, press the 1394 button.
• Show the control panel of MicroMV Camcorder.
Sony
DCR-IP45
CAM
VSTOP
+0:00:06
FF
GG
0:00

TV GUIDE TV/VIDEO
POWER
MENU
VOL
CH

• The control panel of MicroMV Camcorder
-Depending on the connected equipment, marked control panel may differ.
1. MicroMV Camcorder Company
Sony
2. MicroMV Camcorder Model
3. Connected Equipment to the 1394
DCR-IP45
CAM
VSTOP
+0:00:06
FF
GG
0:00
4. MicroMV Camcorder Operating Status
5. Tape Status
• Tape shape Icon - Tape in or not
• Lock shape Icon - Use or not use
6. MicroMV Camcorder Play Time
7. MicroMV Camcorder Play, Search or Stop
8. Initializing Play Time
* Supported MicroMV Camcorder List
SONY MICORMV
SONY MICORMV
SONY MICORMV
SONY MICORMV
SONY MICORMV
SONY MICORMV
34 Plasma TV
IP-5
IP-45
IP-210
IP-7
IP-55
IP-220
IEEE 1394
IEEE 1394 functions continued
MicroMV Camcorder and DVHS
how to play the MicroMV Camcorder and DVHS
1. Synchronously, connect the IEEE 1394 jack of the TV to the IEEE 1394 jack of the DVHS and the
MicroMV Camcorder with IEEE 1394 Cable.
Panasonic
NV-DH1
DVHS
CAM
2. Press the F / G button to select device, then press ENTER button to play it . And then selected device
will be showed OSD.
Panasonic
NV-DH1
DVHS
CAM
Panasonic
NV-DH1
CAM
VSTOP
+0:00:06
FF
GG
0:00
Owner’s Manual 35
IEEE 1394
IEEE 1394 functions continued
How to connect the 1394
• When connecting these 3 methods, the
1394 will not work properly.
(a) LOOP Connection
(b) Daisy Chain


TV GUIDE TV/VIDEO
POWER
MENU
VOL



TV GUIDE TV/VIDEO
POWER
CH
MENU
VOL
CH





(c) MicroMV Camcorder Daisy Chain

or

TV GUIDE TV/VIDEO
POWER

36 Plasma TV
MENU
VOL
CH


TV Guide On Screen System
TV Guide On Screen ® System
Overview
- Your new TV contains the TV Guide On Screen Interactive Program Guide.
- The TV Guide On Screen system has features that help you get the most out of your viewing
experience.
TV Guide On Screen Overview
The TV Guide On Screen system has the following features:
•Eight days of show listings (today plus seven days).
•Icons that indicate show rating, stereo, HDTV, new episode, etc.
•Intuitive up/down/left/right navigation using your remote control.
•Set shows to Record.
•Schedule show Reminders.
•Search shows by category (e.g., Movies, Sports, Children, etc.).
•Search for shows based on keywords or alphabetically by title.
•Direct tuning to a channel.
•Show information while watching TV.
•Streamlined System Setup and default setting options.
•Channel lineup customization.
•Help screens while in the Guide.
Owner’s Manual 37
TV Guide On Screen System
TV Guide On Screen ® System continued
Screen Components
- The screens displayed in the TV Guide On Screen system share many of the same compo-
nents, as shown in the following figure:
•Video Window - displays TV video while the Guide is displayed
•Service Bar - provides access to the 4 main Guide Services
•Current Service Label - indented to indicate current Service displayed
•Tile - displays show title
•Highlight - indicates an active tile
•Info Box - provides information for a highlighted item
•Info Button - cycles through the various Info Box sizes
•Channel Logo - identifies network
•Record/Remind Icons - indicates a show is set to Record or set as a Reminder
•Panel Ad - location where show- or product-specific information appears (and also where Panel Menu appears)
38 Plasma TV
TV Guide On Screen System
TV Guide On Screen ® System continued
• Panel Menu
•A Panel Menu appears when the Menu key is pressed on a highlighted tile and additional options are available. It also
appears when you press ENTER on a show starting in the future.
•When a Panel Menu appears, the highlighted tile changes color to indicate the Panel Menu relates to this tile.
•The Panel Menu displays below the Video Window.
•Help is available for a displayed Panel Menu by pressing the INFO button.
•The
D /E
button move between the options within the Panel Menu.
•The left and right arrows move to adjacent options unless the highlight is on an odometer, where these arrows change the
odometer choice.
•Pressing ENTER from an odometer or number entry box moves the highlight to the default command button of that Panel
Menu, for example, Schedule Reminder.
•Pressing ENTER from a highlighted command button executes the action and closes the Panel Menu (e.g., Schedule
Reminder, Cancel).
•Select Cancel to cancel any changes and press ENTER to close this menu.
•Pressing Menu is a shortcut to Cancel. Press Menu to cancel any changes and close the menu.
•If a Panel Menu contains more menu options than can be displayed on a single screen,
D /E
button appear at the top or
bottom of a menu. Simply scroll down to access these options.
Owner’s Manual 39
TV Guide On Screen System
TV Guide On Screen ® System continued
Main Services
V < Listings >
- Access Listings by pressing the TV Guide button on your remote or on the front panel of your TV.
- Listings is always the first Service displayed in the Guide.
- With Listings highlighted, press the Info button to display a Help screen.
Press the Info button again to close the screen.
Use the
D /E /F /G
buttons to move the highlight
within Listings to:
•View 8 days of show listings
•Read show descriptions
•Tune directly to a show currently airing
•Set a show to Remind
•Set a show to Record
•Lock and unlock the Video Window
•Access Panel and Channel Ads
Notes: There may be times when the TV Guide On
Screen system could display partial or no program listings. The reasons for this include:
• Program schedule information was not provided to TV
Guide On Screen.
• The transmission of the program listings was interrupted.
The phrase “No Listings” will be replaced with program
information during the next transmission, which should
occur within the next 24 hours.
Please remember to turn off your TV when not in use
in order to receive program listings.
40 Plasma TV
TV Guide On Screen System
TV Guide On Screen ® System continued
V < Search >
- Search lets you find shows by category (Alphabetical, Movies, Sports, Children, Educational, News, Variety, Series, HDTV) or by
Keyword.
- With Search highlighted, press the Info button to display a Help screen.
Press the Info button again to close the screen.
•Category Search Example: Movies
1. From Search, use the
button to highlight Movies.
Owner’s Manual 41
TV Guide On Screen System
TV Guide On Screen ® System continued
2. Use the
button to highlight a subcategory (for example, All).
3. Press ENTER to display a list of all Movies, organized by date
and time.
4. Highlight a show and press ENTER to watch (if on now) or
the Menu key to display the Episode Options menu.
You can choose to set a recording, a reminder, or tune to the
channel.
Go to Service Bar - closes the menu, changes no information, and returns to the Search Service Bar.
Tune to Channel - exits the Guide and tunes to the channel of the highlighted show (show airs in the future).
Note: This option reads Watch Now if the show is currently airing.
Set Recording - displays the Record Options menu, from
which you can set frequency, start and end time, etc.
Set Reminder - displays the Remind Options menu, from
which you can set frequency, when, automatically power
On, and auto-tune the TV.
Cancel - closes the menu, changes no information, and
returns to the highlighted show.
42 Plasma TV
TV Guide On Screen System
TV Guide On Screen ® System continued
• Keyword Search
- Keyword search lets you enter a word(s) to look for a particular show by category or for every show title that matches.
1. Highlight the Keyword navigation label, and press
ENTER button to display the Keyword Search menu.
2. Highlight New Search, and press ENTER button.
3. The Search Options menu is displayed.
4. Highlight Category, and use the F
/ G button to select
a category to search (e.g. All, HDTV, Children, Sports,
etc.). When finished, use the E button to highlight
Enter Keyword.
5. Highlight Enter Keyword, and press ENTER.
Then the keyboard is displayed.
6. Use the D / E / F / G button to highlight a character,
and press ENTER to display it. When complete, highlight Done and press ENTER.
Owner’s Manual 43
TV Guide On Screen System
TV Guide On Screen ® System continued
7. A list of all matching shows for that keyword is displayed.
Like the Category Search Example, you can highlight
a show, and press ENTER to display all airings. You
can then highlight a specific listing and press ENTER
to watch (if On now) or the Menu key to display the
Episode Options menu.
From the Episode Options menu, choose to set a
recording, a reminder, or tune to the channel, as previously described.
The TV guide on screen system stores all the keywords
you create. To edit or delete a keyword, highlight the
keyword and press the Menu key. A Search Options
menu is displayed.
Go to Service Bar - closes the menu, changes no information, and returns to the Search Service Bar.
Edit Search - displays the keyboard, where you can
change the keyword.
Delete Search - A Confirm menu is displayed.
•Yes - deletes the Search
•No - closes the panel menu
Cancel - closes the menu, changes no information, and
returns to the highlighted show.
44 Plasma TV
TV Guide On Screen System
TV Guide On Screen ® System continued
V < Schedule >
- Schedule lets you review, edit, or delete Record and Remind events that you set previously.
- With Schedule highlighted, press the Info button to display a Help screen. Press the Info button again to close the screen.
- An icon identifies the event type:
Record
W Once
—records the show one time
Regularly
, Daily
—records the show every time
the show airs on the same channel and starts at the same
time
W Weekly
—records the show each time the show airs on
the same day of the week, on the same channel and starts at
the same time
Off
—keeps the show in the list but will not record this
show until the frequency is changed.
Remind
W Once
—sets a show reminder one time
Regularly
, Daily
—sets a show reminder
every time the show airs on the same channel and
starts at the same time
W Weekly
—sets a show reminder each time the
show airs on the same day of the week, on the same
channel and starts at the same time
Off
—keeps the show in the list but will not remind
until the frequency is changed
Highlight an event, and press the Menu key for options.
Go to Service Bar - closes the menu, changes no information,
and returns to the Schedule Service Bar.
Tune to channel - exits the tv guide on screen system and
tunes to the highlighted show.
Delete Recording - removes the recording from the Schedule,
after a Confirm screen.
Edit Recording - opens a menu from which you can change
existing recording information.
Set Reminder - opens a menu from which you can set a
Reminder for the show (Record is not cancelled).
Cancel - closes the menu, changes no information, and returns
to the highlighted show.
Owner’s Manual 45
TV Guide On Screen System
TV Guide On Screen ® System continued
V < Setup >
- After you initially complete Guide Setup, you can make changes to Guide settings in the following areas:
• Change System Settings
• Change Channel Display
• Change Default Options
Highlight a choice, press ENTER, and follow the on-screen instructions.
With Setup highlighted, press the Info button to display a Help
screen. Press the Info button again to close the screen.
• Change System Settings
This option appears after you have completed the initial Guide
Setup process.
Press ENTER to display the Confirming Your Settings screen. You
see your current settings.
Choose one of the options, press ENTER, and follow the on-screen
instructions.
46 Plasma TV
TV Guide On Screen System
TV Guide On Screen ® System continued
• Change Channel Display
Change Channel Display lets you edit channel information
that appears in Listings. With Change Channel Display you
can :
• Re-order the position or the channel appears in Listings
• Change the tune channel number
• Switch a channel
On - the channel is always displayed
Off - the channel is never displayed
Auto-Hide - the channel is only displayed when
program information is available.
Press ENTER to display the Channel Editor screen.
Then, highlight a channel and press Menu. A Grid Options
menu is displayed.
Highlight Go Back to Setup to close the menu, change no
information, and return to the Setup Service Bar.
Or make changes and when finished, press ENTER to highlight Done. Press ENTER again to close the menu and
accept the changes.
Highlight Cancel to close the menu, change no information,
and return to the highlighted channel.
Owner’s Manual 47
TV Guide On Screen System
TV Guide On Screen ® System continued
• Change Default Options
Change Default Options lets you change default settings in the
following categories:
•General Default Options
•Record Defaults
•Remind Defaults
Highlight Change Default Options, and press ENTER.

General Default Options lets you set defaults for the following:
•The initial Info Box size when the TV guide on screen system is
entered.
Choices are No, Small, Large, and Last Used
(Default = Last Used).
•The Info Box size rotation when the Info key is pressed while in
the TV guide on screen system.
Choices are No only, Small only, Large only, No & Small, No &
Large, Small & Large, All (Default = All)
•Automatic entry into the TV guide on screen system (Auto-Guide)
when the TV is powered On.
Choices are On and Off (Default = On).
Highlight General Default Options, and press the Menu key to display the General Default Options menu.
Highlight Go to Service Bar to close the menu, change no information, and return to the Setup Service Bar.
When finished, press ENTER to highlight Done. Press ENTER
again to close the menu and accept the changes.
Highlight Cancel to close the menu, change no information, and
return to the highlighted option.
48 Plasma TV

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 48
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:6b4d4b78-0db6-422e-a97a-a76008d68ca4
Producer                        : Acrobat Distiller 6.0 (Windows)
Modify Date                     : 2004:10:04 19:53:36+09:00
Create Date                     : 2004:10:04 19:53:36+09:00
Creator Tool                    : QuarkXPressª3.3E: LaserWriter 8 Z1-8.7.1
Document ID                     : uuid:8cf597db-1471-4f6b-85d8-3266de7fb92b
Format                          : application/pdf
Title                           : 479Hen
Creator                         : PSY
Author                          : PSY

EXIF Metadata provided by EXIF.tools