LG Electronics USA RU50PY10 Plasma Display Panel User Manual 479Hen
LG Electronics USA Plasma Display Panel 479Hen
Contents
- 1. Users Manual Part 1
- 2. User Manual Part 2
User Manual Part 2
TV Guide On Screen System TV Guide On Screen ® System continued • Change Default Options Change Default Options lets you change default settings in the following categories: •General Default Options •Record Defaults •Remind Defaults Highlight Change Default Options, and press ENTER.General Default Options lets you set defaults for the following: •The initial Info Box size when the TV guide on screen system is entered. Choices are No, Small, Large, and Last Used (Default = Last Used). •The Info Box size rotation when the Info key is pressed while in the TV guide on screen system. Choices are No only, Small only, Large only, No & Small, No & Large, Small & Large, All (Default = All) •Automatic entry into the TV guide on screen system (Auto-Guide) when the TV is powered On. Choices are On and Off (Default = On). Highlight General Default Options, and press the Menu key to display the General Default Options menu. Highlight Go to Service Bar to close the menu, change no information, and return to the Setup Service Bar. When finished, press ENTER to highlight Done. Press ENTER again to close the menu and accept the changes. Highlight Cancel to close the menu, change no information, and return to the highlighted option. 48 Plasma TV TV Guide On Screen System TV Guide On Screen ® System continued < Record Defaults> Record Default Options lets you set defaults for the following: • When to start the record event. Choices are 120 minutes early to 120 minutes late, to On time. (Default = On time) • When to end the record event. Choices are 120 minutes early to 120 minutes late, to On time. (Default = On time) • Recorder choice: Please choose the VCR only. This TV does not provide other devices with a recording feature. Highlight Record Defaults, and press the Menu key to display the Record Default Options menu. Highlight Go to Service Bar to close the menu, change no information, and return to the Setup Service Bar. < Remind Defaults> Remind Default Options lets you set defaults for the following: •Power On the TV, if Off, when a Reminder is scheduled. Choices are Yes and No. (Default = No) •Automatically tune the TV to the channel (TV must be On), when a Reminder is scheduled. Choices are Yes and No. (Default = No) •When to display the reminder screen. Choices are 30 seconds to 15 minutes early, to 30 seconds to 15 minutes late, to On time. (Default = 1 min early) Highlight Remind Defaults, and press the Menu key to display the Remind Default Options menu. Highlight Go to Service Bar to close the menu, change no information, and return to the Setup Service Bar. When finished, press ENTER to highlight Done. Press ENTER again to close the menu and accept the changes. Highlight Cancel to close the menu, change no information, and return to the highlighted option. Owner’s Manual 49 TV Guide On Screen System TV Guide On Screen ® System continued Record And Remind Features V < Record > You can set a show to Record in Listings, Search, and Once Regularly Schedule or change Record settings for a show in Schedule. There are 3 ways to set a show to Record: 1) Using the Record Button on the Remote • Press the Record button on the remote to record the show Once with current default settings (Start and End recording On Time). Each time you press the Record button, you change the record frequency (but not the default settings) among Once (default), Regularly, Daily, Weekly and then Cancel. —records the show one time —records the show every time the show airs on the same channel and starts at the same time Weekly —records the show each time the show airs on the same day of the week, on the same channel and starts at the same time Off (not cancel) —keeps the show in the list but will not record this show until the frequency is changed Note: The proper Record icon appears on the show tile, as the Record button is pressed. 2) From a Panel Menu •Highlight a show, and press Menu to display the Episode Options menu. •Highlight Set Recording, and press ENTER to display the Record Options menu. •Highlight the Frequency option, and use the left and right arrows to choose among Once, Regularly, Weekly, and Off, as previously described. • Recorder choice: Please choose the VCR only. This TV does not provide other devices with a recording feature. •Note: Video Window Lock is operated to on or off using PIP button in Listings mode. 50 Plasma TV Cancel (no icon displayed)—does not record TV Guide On Screen System TV Guide On Screen ® System continued When finished, press ENTER to highlight Schedule Recording. Press ENTER again to close the menu. You see a Record icon for the selected frequency next to the show title. Highlight Cancel to close the menu, change no information, and return to the highlighted show. 3) Manual Recording •Highlight the Schedule Service label, and press Menu to display the Schedule Options menu. •Use the D / E / F / G buttons to move through the options. Use the number or Use the D / E / F / G buttons to change the information, as necessary. •Highlight New Manual Recording and press ENTER to display the Record Options menu. •Current information (i.e., date, start and end times, channel, input) is displayed. • Recorder choice: Please choose the VCR only. This TV does not provide other devices with a recording feature. Owner’s Manual 51 TV Guide On Screen System TV Guide On Screen ® System continued •Use the left and right arrows to choose between Once, Daily, Weekly, and Off, as follows. Once —records the time, channel, input, recorder combi- nation one time. W Daily —records the time, channel, input, recorder combination Monday through Friday. Weekly —records the time, channel, input, recorder com- bination once a week on this selected day of the week Off (not cancel) —keeps the time, channel, input, recorder combination in the list without recording until the frequency is changed. When finished, press ENTER to highlight Schedule Recording. Press ENTER again to close the menu. You see a Record icon for the selected frequency next to the show title. Note: Manual recording is listed by channel number. Highlight Cancel to close the menu, change no information, and return to the highlighted show. Before a recording begins, a notification screen appears if you are using a Cable box and your TV is On. At that time, you can choose to start or cancel recording. If the TV is not On, the recording occurs as scheduled. If there is no activity for 3 minutes, the notification screen automatically closes and completes the highlighted item. Record Conflict A conflict message appears for the following reasons: • a show set to Record overlaps with any part of another show previously set to Record, • a show set to Record overlaps with a show previously set to autotune Select one of these options: W record anyway - this show will override an existing show set to Record or auto-tune W don't record this show - cancel the Recording 52 Plasma TV TV Guide On Screen System TV Guide On Screen ® System continued V < Remind > You can set a show Reminder in Listings, Search, and Schedule or change Reminder settings for a show in Schedule. There are 2 ways to set a show Reminder: 1) From a Panel Menu • Highlight a show, and press Menu to display the Episode Options menu. • Highlight Set Reminder, and press ENTER to display the Remind Options menu. •Highlight the Frequency option, and use the left and right arrows to choose between: Once —sets a show reminder one time Regularly —sets a show reminder every time the show airs on the same channel and starts at the same time Weekly —sets a show reminder each time the show airs on the same day of the week, on the same channel and starts at the same time W Off —keeps the show in the list but will not remind until the frequency is changed •Power On the TV, if Off, when a Reminder is scheduled. Choices are Yes and No. (Default = No) •Automatically tune the TV to the channel (TV must be On), when a Reminder is scheduled. Choices are Yes and No. (Default = No) •When to display the reminder screen. Choices are 30 seconds to 15 minutes early, to 30 seconds to 15 minutes late, to On time. (Default = 1 min early) When finished, press ENTER to highlight Schedule Reminder. Press ENTER again to close the menu. You see a Remind icon for the selected frequency next to the show title. Highlight Cancel to close the menu, change no information, and return to the highlighted show. Owner’s Manual 53 TV Guide On Screen System TV Guide On Screen ® System continued 2) Manual Reminder •Highlight the Schedule Service label, and press the Menu key to display the Schedule Options menu. •Use the D / E / F / G buttons to move through the options. Use the number or D / E / F / G buttons to change the information, as necessary. •Highlight New Manual Reminder and press the ENTER key to display the Remind Options menu. •Current information (i.e., date, start and end times, channel, input, frequency, etc.) is displayed. •Highlight the Frequency option, and use the F / G buttons to choose among Once, Daily, Weekly, and Off, as follows. Once —sets a show reminder for the time, channel, input, recorder combination one time W Daily —reminds for the time, channel, input, recorder combination Monday through Friday W Weekly —sets a show reminder for the time, channel, input, recorder combination once a week on this selected day of the week W Off (not cancel) —keeps the time, channel, input, destination combination in the list without reminding until the frequency is changed •Power On the TV, if Off, when a Reminder is scheduled. Choices are Yes and No (Default =No). •Automatically tune the TV to the channel (TV must be On), when a Reminder is scheduled. Choices are Yes and No (Default = No). When finished, press ENTER to highlight Schedule Reminder. Press ENTER again to close the menu. You see a Remind icon for the selected frequency next to the show title. Note: Manual reminder is listed by channel number. Highlight Cancel to close the menu, change no information, and return to the highlighted show. 54 Plasma TV TV Guide On Screen System TV Guide On Screen ® System continued Based on your option settings, a notification screen will appear, if your TV is On at the reminder time. You can then choose to hide the reminder, or highlight the show, and press ENTER to tune to the show. If there is no activity for 3 minutes, the notification screen automatically closes and completes the highlighted item (hide reminders). If you choose Hide Reminders, the window closes for the show or shows, but does not affect other Reminders you set. Note: If more than 2 reminders are set for the same time, arrows appear on the Reminder screen. Use the buttons to view the shows. D /E Remind Conflict A conflict message appears for the following reasons: • a show set with an Auto-Tune Reminder has the same start time as an existing Auto-Tune Reminder. • If you are using a cable box, a show set with an AutoTune Reminder overlaps with a Recording already scheduled. Select one of these options: auto-tune anyway - this show will override an existing show set to auto-tune W proceed, no auto-tune - set the show as a Reminder but do not auto-tune W don't set this reminder - cancel the Reminder Owner’s Manual 55 Operation Operation Screen Setup for PC mode - Be sure to select the RGB-PC/RGB-TV SET source before operation. (For RGB-DTV input source, Position and Reset are available.) - In RGB-PC/DVI-PC input source, setting are available. - You can manually adjust picture position and minimize image shaking for the PC input source. Adjustment for screen Position, Size, and Phase 1. Press the ADJUST button and then use D or PHASE. 2. Press ENTER button and then use adjustments. /E button to select POSITION, SIZE, D /E /F /G buttons to make appropriate POSITION SIZE PHASE • The PHASE adjustment range is -16 ~ +16. • The SIZE adjustment range is -30 ~ +30. RESET 3. Press ENTER button. Adjust Close •Note: In HDMI/DVI-PC mode, screen PHASE is not available. Initializing (Reset to original factory values) - To initialize the adjusted values 1. Press the ADJUST button and then use D 2. Press ENTER button and then use 3. Press ENTER button F /G /E button to select the RESET option. button to select Yes. POSITION SIZE Initialize Settings PHASE RESET Adjust Close 56 Plasma TV Operation Turning the TV On 1. First, connect power cord correctly. At this moment, the TV switches to standby mode. In standby mode to turn TV on, press the power, TV/VIDEO, CH (D / E) button on the TV or press the POWER, TV/VIDEO, COMP/RGB/HDMI, CH (+, -), Number (0 ~ 9) button on the TV . 2. Select the viewing source by using TV/VIDEO, COMP/RGB/DVI button on the remote control. This TV is programmed to remember which mode it was last set to, even if you turn the TV off. 3. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode. Notes: • If you intend to be away on vacation, disconnect the power plug from the wall power outlet. • After turning on the TV, it takes time to be initialized for the TV Guide On Screen System. On-screen Menus Language Selection - The menus can be shown on the screen in the selected language. First select your language. 1. Press the MENU button and then use 2. Press the button and then use button to select the OPTION menu. button to select Language. 3. Press the G button and then use D / E button to select your desired language. From this point on, the on-screen menus will be shown in the selected language. SETUP Cinema VIDEO Caption Caption/Text AUDIO Caption Option Language TIME 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Aspect Ratio OPTION English Demo Español ISM Method Français Low Power LOCK CABLE MENU Previous Owner’s Manual 57 Operation Setup Menu Options EZ Scan (Channel Search) - Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list. - Run EZ Scan again after any Antenna/Cable connection changes. 1. Press the MENU button and then use 2. Press the G button and then use D /E D /E button to select the SETUP menu. button to select EZ Scan. 3. Press the ENTER button to begin the channel search. Allow EZ Scan to complete the channel search cycle for TV, DTV, CATV, and CADTV. Manual Scan 1. Press the MENU button and then use 2. Press the G button and then use 3. Press the CADTV. D /E D /E button and then use 4. Press the G button and then use D to add or delete. button to select the SETUP menu. SETUP D / E VIDEO button to select TV, DTV, CATV, and button to select channel number you want 5. Press the ENTER button to add or delete for the channel number. 6. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Channel Label Main Input TIME OPTION Sub Input Aux. Label Set ID LOCK CABLE MENU Notes: •This channel number is different from normal channel showed Channel Edit. •When Cable Box connect to RF2,3,4 in TV Guide Setup, CATV, CADTV is not working in EZ Scan. 58 Plasma TV Select channel type and RF-channel number. Channel Edit DTV Signal AUDIO /E EZ Scan Manual Scan button to select Manual Scan. Previous TV 20 Operation Channel Edit - Create two different types of channel lists in memory: “Custom list” and “Surf" (Favorite) channel list” from the default channel list created from the EZ Scan channel search. - A custom list can be created by toggling each channel on or off with ENTER button. Once a channel is highlighted, you will be able to see whether the channel is currently added or deleted by referring to the small window at the top-left corner of the screen. You can create your own Surf channel with all channels. Use the SURF button on the remote control when a channel is highlighted and then you can create your Surf channel. SETUP EZ Scan Manual Scan VIDEO Channel Edit DTV Signal AUDIO Selection ( G or ) leads you to the channel edit screen. Channel Label Main Input TIME OPTION Sub Input Aux. Label Set ID LOCK CABLE 1. Press the MENU button and then use 2. Press the G button and then use D /E D /E MENU Previous button to select the SETUP menu. button to select Channel Edit. 3. Press the G button. You will now see a screen filled with channel numbers and a preview picture. 4. Use D / E / F / G utton to select a channel and then use the ENTER button to add or delete it. Press SURF to add the channel to the Surf List. 5. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Note: •When Cable Box connect to RF2,3,4 in TV Guide Setup, CATV, CADTV is not working in EZ Scan. DTV Signal Strength - Shows how strong your DTV signal is and whether you need to adjust your antenna or digital cable input. The higher the signal strength, the less likely you are to experience picture degradation. - DTV Signals: When input signals are DTV, CADTV, this function is available. 1. Press the SIGNAL button. 2. View the on-screen signal strength monitor to see the quality of the signal being received. • You can also check the DTV Signal strength with the SETUP menu. Owner’s Manual 59 Operation Setup Menu Options continued Channel Label Setup - Choose preset labels for your channels. - If a channel label is provided on the signal from the broadcasting station, the TV displays a short name for a channel even if you didn't preset a label for the channel. SETUP EZ Scan Manual Scan VIDEO Channel Edit DTV Signal AUDIO Channel Label Main Input TIME OPTION Selection ( G or ) leads you to the channel logo screen. Sub Input Aux. Label Set ID LOCK CABLE MENU Previous 1. Press the MENU button and then use 2. Press the G button and then use D /E D /E button to select the SETUP menu. button to select Channel Label. 3. Press the G button. You will now see a screen filled with Labels and a preview screen. 4. Use the CH +/- button to select a channel to Label. 5. Use D / E / F / G button to select the appropriate label for the channel, then press ENTER button to set the Label to the selected channel. - If you press ENTER button, you will see the channel banner. • For example: CADTV 27-1 DOLBY DIGITAL HD CNN Main Picture Source Selection - Changes the picture source so you can watch your off-air TV, cable TV, VCR, DVD, or any other devices that are connected to your TV. SETUP 1. Press the MENU button and then use 2. Press the G button and then use D /E D /E button to select the SETUP menu. button to select Main Input. EZ Scan Manual Scan VIDEO 3. Press the G button and then use D / E button to select the source: Antenna, Cable, Video, Front Video, Component1, Component2, RGB-DTV (or RGB-PC), HDMI/DVI. AUDIO 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. OPTION Channel Edit Antenna DTV Signal Cable Channel Label Main Input TIME Video Component1 Aux. Label Component2 Set ID RGB-DTV HDMI/DVI LOCK CABLE Front Video Sub Input MENU Previous Aux. Label 1. Press the MENU button and then use 2. Press the G button and then use D /E D /E button to select the SETUP menu. SETUP button to select Aux. Label. 3. Press the G button and then use D / E button to select the source: Video, Front Video, Component1, Component2, RGB, HDMI/DVI. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. EZ Scan Manual Scan VIDEO Channel Edit Front Video Channel Label TIME Set ID LOCK CABLE MENU Previous VCR Component2 Set Top Box Sub Input Aux. Label Cable Box Component1 DVD Main Input OPTION 60 Plasma TV Video DTV Signal AUDIO RGB PC HDMI/DVI Game Operation V ideo Menu Options EZ Picture - EZ Picture adjusts the TV for the best picture appearance. Select the preset value in the EZ Picture menu based on the program category. - When adjusting Video menu options (contrast, brightness, color, sharpness, tint, and color temperature) manually, EZ Picture automatically changes to Off. - Daylight, Normal, Night Time, Movie, Video Game, and Sports settings are preset for optimum picture quality at the factory and are not adjustable. 1. Press the VIDEO button repeatedly to select the picture appearance setup option as shown below: Off (your own settings), Daylight, Normal, Night Time, Movie, Video Game, and Sports. • You can also use the VIDEO menu to adjust EZ Picture. 2. Press the EXIT button to save and return to TV viewing. Manual Picture Control ( Off option) - Adjust the picture appearance to suit your preference and viewing situations. SETUP 1. Press the MENU button and then use D /E button to select the VIDEO menu. 2. Press the G button and then use D / E button to select the desired picture option (Contrast, Brightness, Color, Sharpness, or Tint ). 3. Press the G button and then use F / G button to make appropriate adjustments. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. VIDEO AUDIO EZ Picture Contrast 85 Brightness 50 Color 50 Sharpness 50 Tint TIME OPTION Color Temperature Video Preset LOCK CABLE MENU Previous Color Temperature Control - Choose one of three automatic color adjustments. Set to warm to enhance hotter colors such as red, or set to cool to see less intense colors with more blue. SETUP EZ Picture Contrast VIDEO 1. Press the MENU button and then use 2. Press the button and then use D /E D /E 3. Press the G button and then use D Warm. /E button to select the VIDEO menu. button to select Color Temperature . button to select either Cool, Medium or 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Brightness Color AUDIO Sharpness Tint TIME Color Temperature G Cool Medium OPTION Video Preset Warm LOCK CABLE MENU Previous Owner’s Manual 61 Operation XD - XD is LG Electronic’s unique picture improving technology to display a real HD source through an advanced digital signal processing algorithm. - When selecting EZ Picture options (Daylight, Normal, Night Time, Movie, Video Game, and Sports), XD is automatically change to On. SETUP EZ Picture Contrast VIDEO Brightness Color 1. Press the MENU button and then use D /E button to select the PICTURE menu. AUDIO Sharpness Tint 2. Press the G button and then use 3. Press the button and then use D /E button to select XD. D /E button to set On or Off. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. TIME Color Temperature OPTION Off On Video Preset LOCK CABLE MENU Previous V ideo Preset - Use to quickly reset all the Video menu options to their original factory preset values. SETUP EZ Picture Contrast 1. Press the MENU button and then use 2. Press the button and then use D /E D /E button to select the VIDEO menu. button to select Video Preset . VIDEO Brightness Color AUDIO Sharpness Tint 3. Press the G button to reset the Video menu options to original values. TIME OPTION Color Temperature Video Preset LOCK CABLE 62 Plasma TV MENU Previous Selection ( G or ) presets the video configuration. Operation Audio Menu Options Audio Language - Other languages may be available if a digital signal is provided by the broadcasting station. SETUP VIDEO 1. Press the MENU button and then use D /E button to select the AUDIO menu. button to select Audio Language. D /E button and then use D /E button to select: English, Spanish, or OPTION 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. English Spanish EZ Sound French Treble Bass TIME 3. Press the French. EZ SoundRite Balance AUDIO 2. Press the G button and then use Audio Language Front Surround TV Speaker LOCK CABLE MENU Previous EZ SoundRite - Scans for changes in sound level during commercials, then adjusts the sound to match the specified audio level. SoundRite makes sure that the volume level remains consistent whether you are watching a commercial or a regular TV program. 1. Press the MENU button and then use D /E button to select the AUDIO menu. 2. Press the button and then use D /E button to select EZ SoundRite. 3. Press the button and then use D /E button to select On or Off. SETUP EZ SoundRite VIDEO Off EZ Sound On Balance AUDIO Treble Bass TIME OPTION 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Audio Language Front Surround TV Speaker LOCK CABLE MENU Previous EZ Sound - EZ Sound lets you enjoy the best sound without any special adjustment because the TV sets the appropriate sound options based on the program content. - When adjusting sound options (treble, bass, and front surround) manually, EZ Sound automatically switches Off. - Normal, Stadium, Theater, and Music are preset for good sound quality at the factory and are not adjustable. 1. Press the SOUND button repeatedly to select the appropriate sound setup as shown below: Off (your own settings), Normal, Stadium, Theater, and Music. • You can also adjust EZ Sound in the AUDIO menu. 2. Press EXIT button to save and return to TV viewing. Manual Sound Control ( Off option) - Adjust the sound to suit your taste and room situations. SETUP 1. Press the MENU button and then use D 2. Press the G button and then use D (Balance, Treble, or Bass). /E 3. Press the G button and then use F /G /E button to select the AUDIO menu. EZ SoundRite VIDEO button to select the desired sound option 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. EZ Sound Balance AUDIO button to make appropriate adjustments. Audio Language TIME OPTION Treble 50 Bass 50 Front Surround TV Speaker LOCK CABLE MENU Previous Owner’s Manual 63 Operation Front Surround is a trademark of SRS Labs, Inc. - TruSurround XT technology is incorporated under license from SRS Labs, Inc. - Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. 1. Press the MENU button and then use D 2. Press the button and then use D /E /E button to select the AUDIO menu. button to select Front Surround. 3. Press the G button and then use D / E button to select Off, 3D EchoSound System or SRS (Sound Retrieval System) TruSurround XT.. • 3D EchoSound System Creates a stunning simulated stereo effects from any mono sound and a realistic three-dimensional sound with a very wide and deep sound stage into stereo sound. SETUP Audio Language EZ SoundRite VIDEO EZ Sound Balance AUDIO Treble Bass TIME OPTION Front Surround Off 3D EchoSound System TV Speaker SRS TruSurround XT LOCK • SRS TruSurround XT Takes advantage of any multi-channel format without needing to add extra speakers or equipment. Dialog clarity, bass enrichment, and the addition of stereo audio enhancement that produces an immersive sound experience from standard stereo material. CABLE MENU Previous 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. TV Speakers On/Off On/Off Setup - Turn TV speakers off if using external audio equipment. Feature turns the TV Speakers option On or Off. SETUP EZ SoundRite VIDEO 1. Press the MENU button and then use D 2. Press the 3. Press the button and then use button and then use /E button to select the AUDIO menu. D /E button to select TV Speaker. D /E button to select On or Off. Treble Bass OPTION Front Surround TV Speaker Off On LOCK CABLE Stereo/SAP Broadcasts Setup EZ Sound Balance AUDIO TIME 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Audio Language MENU Previous - This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program; if the station transmits an additional sound signal as well as the original one. - When having selected Stereo or SAP button on the remote control, this TV can only receive the signal in case that the TV station transmits the proper signals. - Mono sound is automatically received if the broadcast is only in Mono; even though Stereo or SAP has been selected. - Select Mono if you want to listen to the mono sound in remote fringe areas during stereo/SAP broadcasting. - Stereo or SAP can be received in Analog channel. 1. Use the SAP button to select your desired MTS mode in analog signal. Each time you press the SAP button, Mono, Stereo, or SAP appear in turn. • If other languages available on the digital signal, select them with the SAP button. 2. Press EXIT button to save and return to TV viewing. 64 Plasma TV Operation T ime Menu Options Auto Clock Setup The time is set automatically from a digital channel signal. The digital channel signal includes information for the current time provided by the broadcasting station. Set the clock manually, if the current time is set incorrectly by the auto clock function. When you set up TV guide on screen system, Auto Clock menu is not selected. 1. Press the MENU button and then use 2. Press the 3. Press the button and then use button and then use D /E button to select the TIME menu. D /E button to select Auto Clock. D /E button to select On. SETUP 5. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Manual Clock VIDEO AUDIO 4. Press the G button and then use D / E button to select your viewing area time zone: Eastern, Central, Mountain, Pacific, Alaska, or Hawaii. Auto Clock Off On Off Timer On Timer Time Zone Eastern Sleep Timer Daylight Saving Auto Off Auto TIME OPTION LOCK CABLE MENU Previous Manual Clock Setup - If current time setting is wrong, reset the clock manually. - When you set up TV guide on screen system, Manual Clock menu is not worked. 1. Press the MENU button and then use 2. Press the button and then use D /E D /E button to select the TIME menu. button to select Manual Clock. SETUP Auto Clock Manual Clock VIDEO AUDIO Year ---- Off Timer Date -- -- On Timer Time -- -- -- Sleep Timer Auto Off 3. Press the G button and then use F / G button to select either the year, date, or time option. Once selected, use the D / E button to set the year, date, and time options. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. TIME OPTION LOCK CABLE MENU Previous On/Off On/Off Timer Setup Timer function operates only if current time has been set. Off-Timer function overrides On-Timer function if they are set both set to the same time. The TV must be in standby mode for the On-Timer to work. If you do not press any button within 2 hours after the TV turns on with the On Timer function, the TV will automatically revert to standby mode. 1. Press the MENU button and then use 2. Press the G button and then use D D /E /E button to select the TIME menu. button to select Off Timer or On Timer. SETUP Auto Clock Manual Clock 3. Press the G button and then use D / E button to select On. • To cancel On/Off timer function, select Off. VIDEO On Timer AUDIO 4. Press the 5. Press the button and then use button and then use 6. For only On timer function Press the G button and then use Press the G button and then use D /E D /E button to set the hour. button to set the minutes. Off Timer D /E button to select the channel at turn-on. button to set the sound level at turn-on. 7. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Off On Auto Off Time 6 : 30 AM TIME OPTION D /E Sleep Timer Ch. TV 2-0 Vol 17 LOCK CABLE MENU Previous Owner’s Manual 65 Operation Sleep Timer - The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off. - You can also set up the Sleep Timer in the TIME menu. 1. Press the TIMER button repeatedly to select the number of minutes. First the Off option appears on the screen, followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes. 2. When the number of minutes you want is displayed on the screen, press the ENTER button. The timer begins to count down from the number of minutes selected. 3. To check the remaining minutes before the TV turns off, press the TIMER button once. 4. To cancel the Sleep Timer, press the TIMER button repeatedly to select Off. Auto Off Off - If set to on and there is no input signal, the TV turns off automatically after 10 minutes. 1. Press the MENU button and then use D / E button to select the TIME menu. 2. Press the G button and then use D / E button to select Auto Off. 3. Press the G button and then use D /E button to select On or Off. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. SETUP Auto Clock Manual Clock VIDEO Off Timer On Timer AUDIO Sleep Timer Auto Off TIME LOCK 66 Plasma TV Off On OPTION CABLE MENU Previous Operation Option Menu Features Aspect Ratio Control - Lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV with a 16:9 ratio picture format. When you receive an analog picture with a 4:3 aspect ratio on your 16:9 TV, you need to specify how the picture is to be displayed. - If you are viewing a picture with a 16:9 aspect ratio, you can’t use the Horizon aspect ratio option. - Horizon aspect ratio is not available for Component 1-2 (720p/1080i)/RGB-DTV (720p/1080i)/HDMI/DVI-DTV (720p/1080i)/DTV(720p/1080i) input source. - RGB-PC/DVI-PC input source use 4:3 or 16:9 aspect ratio. - Note: If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and remain visible. 1. Press the RATIO button repeatedly to select the desired picture format. You can also adjust Aspect Ratio in the OPTION menu. • Set By Program Selects the proper picture proportion to match the source’s image. (4:3 → 4:3, 16:9 → 16:9) • 4:3 Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both the left and right sides. • 16:9 Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen. • Horizon Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both sides, to create a spectacular view. • Zoom 1 Choose Zoom 1 when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped. • Zoom 2 Choose Zoom 2 when you want the picture to be altered, both vertically extended and cropped. The picture taking a halfway trade off between alteration and screen coverage. • Cinema Zoom Choose Cinema Zoom when you want to enlarge the picture in correct proportion. Note: When enlarging or reducing the picture, the image may become distorted. You can adjust the enlarge proportion of Cinema Zoom using D / E button. The adjustment range is 1~16. Cinema Mode Setup SETUP Aspect Ratio Cinema - Set up the TV for the best picture appearance for viewing movies. VIDEO Caption Off On Caption / Text AUDIO 1. Press the MENU button and then use D /E button to select the OPTION menu. 2. Press the G button and then use 3. Press the G button and then use button to select Cinema. / E button to select On or Off. D /E 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Caption Option Language TIME OPTION Demo ISM Method Low Power LOCK CABLE MENU Previous Owner’s Manual 67 Owner’s Manual 67 Operation Caption 1. Press the MENU button and then use 2. Press the G button and then use 3. Press the G button and then use D /E button to select the OPTION menu. button to select Caption. / E button to select On or Off. D /E 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. SETUP Aspect Ratio Cinema VIDEO Caption AUDIO Off On Caption / Text Caption Option Language TIME OPTION Demo ISM Method Low Power LOCK CABLE MENU Previous Caption/Text Caption/Text Analog Broadcasting System Captions Select a caption mode for displaying captioning information if provided on a program. Analog caption displays information at any position on the screen usually the program's dialog. Text displays information, usually at the bottom position and is used for a data service, generally not program related. Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna/Cable. This TV is programmed to remember the caption/text mode it was last set to, when you turn the power off. 1. Use the CC button repeatedly to select Caption CC1, CC2, CC3, CC4, Text1, Text2, Text3, or Text4. • EZ Mute shows the selected captions option (if available on program) when the TV sound is muted .2. Press EXIT button to save and return to TV viewing. • You can also use the OPTION menu to select Caption/Text. 1. Press the MENU button and then use D / E button to select the OPTION menu. 2. Press the G button and then use D / E button to select Caption/Text. SETUP Aspect Ratio CC 1 Cinema 3. Press the G button and then use D / E button to select caption: CC1, CC2, CC3, CC4, Text1, Text2, Text3, or Text4. VIDEO Caption / Text AUDIO • CAPTION The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired. • TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster. CC 2 Caption TIME OPTION CC 3 Caption Option CC 4 Language Text 1 Demo Text 2 ISM Method Text 3 Low Power Text 4 LOCK CABLE MENU Previous 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Digital Broadcasting System Captions - Choose the language you want the DTV/CADTV Captions to appear in. - Languages can be chosen for digital sources only if they are included on the program. 1. Press the MENU button and then use D / E button to select the OPTION menu. 2. Press the G button and then use D / E button to select Caption/Text. 3. Press the G button and then use D / E button to select available caption languages: English, Spanish, or French. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. SETUP Aspect Ratio Cinema VIDEO Caption Caption / Text AUDIO TIME OPTION Spanish French Demo ISM Method Low Power 68 Plasma TV English Language LOCK CABLE Caption Option MENU Previous Operation Option Menu Features continued Caption Option - Customize the DTV/CADTV captions that appear on your screen. button to select the OPTION 1. Press the MENU button and then use menu. D /E 2. Press the G button and then use button to select Caption Option. SETUP D /E Cinema VIDEO 3. Press the G button and then use F /G button to select Custom. 4. Use D / E button to customize the Style, Font, etc., to your preference. A preview icon is provided at the bottom of the screen, use it to see the caption language. • • • • • • • • Size: Set the size the words will appear in. Font: Select a typeface for the words. Text Color: Choose a color for the text. Text Opacity: Specify the opacity for the text color. Bg (Background) Color: Select a background color. Bg (Background) Opacity: Select the opacity for the background color. Edge Type: Select an edge type. Edge Color: Select a color for the edges. Aspect Ratio Caption Caption/Text AUDIO Caption Option TIME A Standard Font Font 0 Text Color White Solid Bg Color Demo ISM Method Low Power Black Bg Opacity Solid Edge Type None Edge Color LOCK CABLE Custom Size Text Opacity Language OPTION Style MENU Black Previous 5. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Demo - EZ Demo Use to scan the features and menu options available on your TV. - XD Demo Use to see the difference between XD Demo On and XD Demo Off. SETUP Aspect Ratio Cinema VIDEO Caption Caption/Text 1. Press the MENU button and then use D 2. Press the button and then use 3. Press the G button and then use D /E D /E /E button to select the OPTION menu. button to select Demo. button to select EZ Demo or XD Demo. AUDIO Caption Option Language TIME OPTION Demo ISM Method EZ Demo Demo Low Power 4. Press the G button to start EZ Demo or XD Demo. Press EXIT button to stop EZ Demo or XD Demo. LOCK CABLE MENU Previous Owner’s Manual 69 Operation Option Menu Features continued ISM (Image Sticking Minimization) Method - A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost image remaining; even when you change the image. Avoid allowing any fixed image to remain on the TV's screen for a long period of time. 1. Press the MENU button and then use D 2. Press the button and then use D /E /E button to select the OPTION menu. button to select ISM Method. SETUP Cinema VIDEO 3. Press the G button and then use D wash, Orbiter or Inversion. /E Aspect Ratio button to select either Normal, White Caption Caption/Text AUDIO Caption Option Language • Normal If image sticking is never a problem, ISM is not necessary - set to Normal. • White wash White Wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear entirely with White Wash. To return to normal viewing, press the any button. • Orbiter Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the image will move once per minute: Right → Right → Downside → Downside → Left → Left → Upside → Upside. • Inversion Inversion will automatically invert the plasma display panel color every 30 minutes. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. 70 Plasma TV TIME OPTION Demo ISM Method Low Power LOCK CABLE MENU Previous Normal White Wash Orbiter Inversion Operation Low Power - Low power reduces the plasma display power consumption. 1. Press the MENU button and then use D /E button to select the OPTION menu. 2. Press the button and then use D /E button to select Low power. 3. Press the button and then use D /E button to select On or Off. Aspect Ratio SETUP Cinema VIDEO Caption Caption / Text AUDIO Caption Option • When you select On, the screen darkens. Language TIME 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Demo ISM Method OPTION Low Power Off On LOCK CABLE MENU Previous Owner’s Manual 71 Split Zoom (DTV 720p, or 1080i mode only) - Enlarges the picture with correct proportions. - When enlarging the picture, the image may become distorted. 1. Press the ZOOM button in DTV 720p, or 1080i modes. buttons to select the screen split zoom section. D /E /F /G 3. To return to normal viewing, press the ZOOM button again. 2. Use the Owner’s Manual 71 Operation Lock Menu Options Parental Control can be used to block specific channels, ratings and other viewing sources. The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by the type of program and by the categories chosen to be blocked. It is also possible to block all program viewing for a time period. To use this function, the following must be done : 1. Set ratings and categories to be blocked. 2. Specify a password 3. Enablethe lock V-Chip rating and categories Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie Rating System (MPAA) only. Ratings for Movies previously shown in theaters: Movie Ratings : • Blocking Off (Permits all programs) •G (General audience) • PG (Parental guidance suggested) • PG-13 (Parents strongly cautioned) •R (Restricted) • NC-17 (No one 17 and under admitted) •X (Adult only) If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked. Ratings for Television programs including made-for-TV movies : • TV-G • TV-PG • TV-14 • TV-MA • TV-Y • TV-Y7 (General audience) (Parental guidance suggested) (Parents strongly cautioned) (Mature audience only) (All children) (Children 7 years older) TV Rating Children: • Age • Fantasy Violence (applies to TV-Y, TV-Y7) (applies to TV-Y7) TV Rating General: • Age • Dialogue - sexual dialogue • Language - adult language • Sex - sexual situations • Violence (applies (applies (applies (applies (applies Aux. Block • Video, Front Video • Component 1, 2 • RGB, HDMI/DVI 72 Plasma TV (On, Off) (On, Off) (On, Off) to TV-G, TV-PG, TV-14, TV-MA) to TV-PG, TV-14) to TV-PG, TV-14, TV-MA) to TV-PG, TV-14, TV-MA) to TV-PG, TV-14, TV-MA) Operation Parental Lock Setup - Set up blocking schemes to block specific channels, ratings, and external viewing sources. - A password is required to gain access to this menu if the Lock System is turned on. 1. Press the MENU button and then use D Then, press the G button /E button to select the LOCK menu. SETUP Lock System Set Password • If Lock is already set, enter the password as requested. • The TV is set up with the initial password “0-0-0-0”. VIDEO • Lock System: Activates or disables the blocking scheme you set up previously. • Set Password: Change the password by inputting a new password twice. • Movie Rating (MPAA): Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas. • TV Rating-Children: Prevents children from watching certain children's TV programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audiences in the TV Rating - sub menu, your children can view those programs. • TV Rating-General: Based on the ratings, blocks certain TV programs that you and your family do not want to view. • Aux. Block: Enables you to select a source to block from the external source devices you have hooked up. Off On Block Channel Movie Rating AUDIO 2. Use the D / E button to choose from the following Lock Menu options. Once the option is selected, change the settings to your preference. TV Rating-Children TV Rating-General TIME Aux. Block OPTION LOCK CABLE MENU Previous 3. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Note: • If you ever forget your password, key in ‘7’, ‘7’, ‘7’, ‘7’ on the remote control. Owner’s Manual 73 Operation CableCARD ™ Function * In this manual, the OSD (On Screen Display) may be different from your TV’s because it is just example to help the TV operation. Cable menu options In case of Scientific Atlanta CableCARD™ - The Cable sub menu displays when inserting the CableCARDTM to the TV. - The CableCARDTM type is Motorola, Scientific Atlanta (SA), or SCM etc. The OSD (On screen display) is different from your TV according to your CableCARDTM type. 1. Press the MENU button and then use 2. Press the button and then use 3. Press the button. D /E D /E SETUP SA CableCARD™ Diag Screen SA CableCARD™/Host ID Screen button to select the CABLE menu. button to select your desired item. VIDEO AUDIO TIME 5. Press EXIT button to return to TV viewing. OPTION LOCK CABLE MENU i.e) CableCARD™/ Host ID Screen CableCARD™ Message In order to start service for this device, please contact customer service at Ph#: 1-866-303-0422 As shown, the pairing number means your TV and CableCARDTM ID. For further information regarding cable TV service, contact your local cable TV service provider(s). CableCARD™(tm): 0-010-405-698-001 HOST ID: 0-080-000-000-226 EXIT Exit Scrambled channel - Insert the CableCARDTM. If you do it at first, it takes about 1 minute to exchange the data between the TV and the CableCARDTM. Then, TV screen displays as shown right. - Let your cable TV service provider know CableCARDTM ID and Host ID. - If your cable TV service provider is registered CableCARDTM ID and Host ID, you can watch the premium or high value channel. - If you ever registered to the cable TV service provider, you can watch the premium or high value channel without a message. CableCARD™ Message In order to start cable service for this device, please contact SuperVision Cable at 1-800-555-8888 POD ID: 7-561-034-449-009 Host ID: 0-100-331-784-018 EXIT Please call your operator and report an invalid CableCARDTM. - If the certificate don’t match between the TV and the CableCARDTM, the OSD (On screen display) displays as shown left. 74 Plasma TV Exit Operation Cable Channel List 1. 2. SETUP EZ Scan Manual Scan VIDEO Channel Edit DTV Signal AUDIO Selection ( G or ) leads you to the channel edit screen. Channel Label Main Input TIME OPTION Sub Input Aux. Label LOCK CABLE 3. MENU Prev. 4. 1. If you enter the Channel Edit after running the EZ Scan, you can see the cable channel list. 2. Inserting the CableCARDTM. Then, the TV receive a new cable channel list. At this time, it takes about 2~3 minutes. (Occasionally more than that time). Note: • As data gathering of CableCARDTM, it may make a noise by fan in standby mode. Emergency Alert Message - If an emergency situation occur during watching the TV, you can receive a message from cable TV service provider(s). - When receiving an emergency message, the message is displayed on the screen as shown below or the channel is changed automatically to a channel that maintains the emergency message. The message automatically disappeared. Emergency Action Notification Hurricane will be coming!!! Owner’s Manual 75 Operation Remote Control PIP (Picture-In-Picture) / POP / Twin Picture - PIP lets you view 2 different inputs (sources) on your TV screen at the same time. One source will be large, and the other source will show a smaller inset image. - Twin Picture mode splits the screen into 2, allowing 2 picture sources to be shown on the TV screen at the same time. Each source is given half the screen. - If you set the block/rating for Lock menu options in PIP/Twin Picture mode, “Rating Blocked” doesn’t display on screen. Watching PIP/POP/Twin PIP/POP/Twin Picture Press the PIP button to access the sub picture. Each press of PIP changes the PIP options as shown below. PIP Mode Twin Picture Mode POP Mode TV 2-0 TV 4-0 TV 6-0 PIP Off Selecting an Input Signal Source for PIP/Twin PIP/Twin Picture Use the PIP INPUT button to select the input source for the sub picture. Each press of PIP INPUT button changes the PIP source. You can also select sources for the Sub Input in the SETUP menu. Main Picture Source DTV Analog Available Sub Picture Sources Analog, Video, and Front Video DTV, Analog, Video, and Front Video Swapping the PIP/T win Picture PIP/Twin Repeatedly, use the SWAP button to switch the main and sub pictures. • Component 1, Component 2, RGB-PC (or RGB-DTV), HDMI/DVI input sources for the main picture can’t be used to swap the main and sub pictures. Main Picture Sub Picture Main Picture Sub Picture TV Program selection for PIP 1. Press the PIP button. 2. Select the Antenna or Cable option on the Sub input menu or with the PIP INPUT button. Use the PIPCH+ PIPCH- button to select a channel for the sub picture. (You can’t select DTV for main and sub picture simultaneously). 76 Plasma TV Operation Moving the PIP sub picture In PIP mode, press the screen. button to move the sub picture to a different location on the Adjusting Main and Sub Picture Sizes for Twin Picture Use the i.e) D /E /F /G D /E /F /G button to change main and sub picture sizes in Twin Picture mode. If screen is adjusted to the maximal size, the large screen is filled with entire screen vertically as shown. POP (Picture-out-of-Picture: Channel Scan) - Use POP to search the programs of all the memorized channels one-by-one on the 3 PIP screen display, (while the main picture source remains the current channel). The pictures of all the programmed channels are searched with the 3 POP screen. - Notes: •Run EZ Scan channel search before using POP mode. •When Sub pictures are changed from the TV/DTV to CATV/CADTV in POP mode, it may make a noise from the Tuner switch. 1. Press the PIP button to activate the POP mode while in PIP mode. • Channel selection: Use F button to enlarge the selected channel being searched on the PIP screen to shift it for viewing on the Main screen. • PIP selection: Use D / E button to select one of 3 PIP screen pictures in POP mode. • When watching TV on Main picture, TV or DTV on Sub pictures are in channel scanning. However, when watching DTV on Main picture, only TV on Sub picture is in channel scanning. TV 2-0 TV 4-0 TV 6-0 2. Press the EXIT button to cancel POP mode. Owner’s Manual 77 Operation Information Operation: • Watching TV/DTV/CATV/CADTV • Watching Video, Front Video • Watching IEEE 1394 • In Component1, Component2, RGB, HDMI/DVI modes, INFO button is not working. 4:3 Screen Ratio of Input Signal 4:3 16 : 9 Screen Ratio of Input Signal 16:9 480i 480p 720p Function: • Show the present screen information. • On Watching with the upper Input signal, press the INFO button. • Press the INFO button or EXIT button to exit. A: Banner information, Refer to the . B: Program title C: Day, Month, Year D: Program start time E: Program finish time F: Show the prosessing rate G: Present time H: Added information. Refer to the icon explanation. Resolution of Input Signal 720x480i Resolution of Input Signal 720x480p Resolution of Input Signal 1280x720p 1080i Resolution of Input Signal 1920x1080i Multilingual : Input Signal have over two Audio inforCC mation. Press the SAP button to select wanted Audio. Caption: Input Signal have over one Close service. Press the CC button to select wanted Closed caption. Input Signal have rating information . Refer to the . D (Dialogue), L (Language), S (Sex), V (Violence), FV (Fantasy Violence) Sophie’s Choice 3:11AM TV 6-0 MONO Tue, Oct 7, 2004 7:00PM STEREO 9:00PM CNBC CC Caption 4 : 3 480i TV-PG D L S V 78 Plasma TV Operation EZ Mute - Nothing to do with Caption on/Off using Mute button, the mode selected Caption/Text is to be displayed. - When you repeatedly press the Mute button, the screen is displayed in turn. (Refer to the lower picture) Mute EZ Mute 24 Note: • EZ Mute only operates in DTV/Analog/Video/Front Video/IEEE1394. Owner’s Manual 79 External Control Device Setup External Control Device Setup - Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally. - Connect the serial port of the control device to the RS-232C jack on the Monitor back panel. - RS-232C connection cables are not supplied with the Monitor. RS-232C Setup HDMI / DVI(VIDEO) DIGITAL AUDIO(OPTICAL) DVI AUDIO INPUT COMPONENT2 Cable VIDEO INPUT CABLE ANTENNA AC INPUT PC Type of Connector; D-Sub 9-Pin Male No. Pin Name No connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection RS-232C Configurations 3-Wire Configurations (Not standard) 7-Wire Configurations (Standard RS-232C cable) RXD TXD GND DTR DSR RTS CTS 80 Plasma TV PC PDP D-Sub 9 D-Sub 9 TXD RXD GND DSR DTR CTS RTS RXD TXD GND DTR DSR RTS CTS PC PDP D-Sub 9 D-Sub 9 TXD RXD GND DTR DSR RTS CTS External Control Device Setup Set ID Use this function to specify a monitor ID number. Refer to ‘Real Data Mapping’. See page 82. SETUP EZ Scan Manual Scan 1. Press the MENU button and then use D /E button to select the SETUP menu. 2. Press the G button and then use button to select SET ID. VIDEO Channel Edit DTV Signal D /E AUDIO 3. Press the G button and then use D / E button to adjust SET ID to choose the desired monitor ID number. The adjustment range of SET ID is 1 ~ 99. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Channel Label Main Input TIME OPTION Sub Input SET ID LOCK Aux. Label MENU Previous Communication Parameters • Baud rate : 9600 bps (UART) • Data length : 8 bits • Parity : None • Stop bit : 1 bit • Communication code : ASCII code * Use a crossed (reverse) cable. Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] Command Reference List COMMAND 1 COMMAND 2 DATA (Hexadecimal) 01. Power 02. Input Select 03. Aspect Ratio 04. Screen Mute 05. Volume Mute 06. Volume Control 07. Contrast 08. Brightness 09. Color 10. Tint 11. Sharpness 12. OSD Select 13. Remote Control Lock Mode 14. PIP/Twin 15. PIP Position 16. Treble 17. Bass 18. Balance 19. Color Temperature 20. PIP Input Source 21. ISM Method 22. White Wash 23. Orbiter Time Setting 24. Orbiter Pixel Setting 0~1 0~8 0 ~ 15 0~1 0~1 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0~1 0~1 0~3 0~3 0 ~ 64 0 ~ 64 0 ~ 64 0~2 0~3 0~2 0~1 1 ~ FE 1 ~A * [Command 1]: First command to control the set. (j or k) * [Command 2]: Second command to control the set. * [Set ID]: You can adjust the set ID to choose desired monitor ID number in Setup menu. Adjustment range is 1 ~ 99. When selecting Set ID ‘0’, every connected the TV is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa decimal (0x0~0x63) on transmission/receiving protocol. * [DATA]: To transmit command data. Transmit ‘FF’ data to read status of command. * [Cr]: Carriage Return ASCII code ‘0x0D’ * [ ]: ASCII code ‘space (0x20)’ OK Acknowledgement [Command2][ ][Set ID][ ][OK][Data][x] * The Monitor transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer. Error Acknowledgement [Command2][ ][Set ID][ ][NG][Data][x] * The Monitor transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions or communication errors. Data 1: Illegal Code 2: Not supported function 3: Wait more time COMCOMDATA 0 DATA 1 DATA 2 DATA 3 MAND 1 MAND 2 (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) 25. Channel Tuning 26. Channel Add/Del 27. Key 01 ~ 87 00 ~ 01 01 ~ 87 00 ~ FE 00 ~ FF Owner’s Manual 81 External Control Device Setup 01. Power (Command2:a) 05. Volume Mute (Command2:e) G To control Power On/Off of the Monitor. G To control volume mute on/off. You can also adjust mute using the MUTE button on remote control. Transmission Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 0 : Power Off 1 : Power On Acknowledgement [k][e][ ][Set ID][ ][Data][Cr] Data 0 : Volume mute off (Volume on) 1 : Volume mute on (Volume off) [a][ ][Set ID][ ][OK][Data][x] * In a like manner, if other functions transmit ‘FF’ data based on this format, Acknowledgement data feedback presents status about each function. Acknowledgement [e][ ][Set ID][ ][OK][Data][x] 06. Volume Control (Command2:f) 02. Input Select (Command2:b) (Main Picture Input) G To select input source for the Monitor. G To adjust volume. You can also adjust volume with the volume buttons on remote control. Transmission Transmission [k][b][ ][Set ID][ ][Data][Cr] Data 0: Antenna 1: Cable 2: Video 3: Front Video 4: Component 1 [k][f][ ][Set ID][ ][Data][Cr] 5: 6: 7: 8: Component 2 RGB-DTV RGB-PC HDMI/DVI Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping’ as shown below. Acknowledgement [f][ ][Set ID][ ][OK][Data][x] Acknowledgement 07. Contrast (Command2:g) [b][ ][Set ID][ ][OK][Data][x] G To adjust screen contrast. You can also adjust contrast in the Video menu. 03. Aspect Ratio (Command2:c) (Main picture format) G To adjust the screen format. You can also adjust the screen format using the RATIO button on remote control or in the Option menu. Transmission [k][c][ ][Set ID][ ][Data][Cr] Data 0: 1: 2: 3: 4: Set by program 4:3 16:9 Horizon Zoom 1 Transmission [k][g][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping’ as shown below. Acknowledgement [g][ ][Set ID][ ][OK][Data][x] 5: Zoom 2 6: Cinema Zoom (1) 15: Cinema Zoom (16) Acknowledgement [c][ ][Set ID][ ][OK][Data][x] 04. Screen Mute (Command2:d) 08. Brightness (Command2:h) G To adjust screen brightness. You can also adjust brightness in the Video menu. Transmission [k][h][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping’ as shown below. Acknowledgement [h][ ][Set ID][ ][OK][Data][x] G To select screen mute on/off. Transmission [k][d][ ][Set ID][ ][Data][Cr] Data 0 : Screen mute off (Picture on) 1 : Screen mute on (Picture off) Acknowledgement [d][ ][Set ID][ ][OK][Data][x] * Real data mapping 0 : Step 0 A : Step 10 (SET ID 10) F : Step 15 (SET ID 15) 10 : Step 16 (SET ID 16) 63 : Step 99 (SET ID 99) 64 : Step 100 82 Plasma TV External Control Device Setup 09. Color (Command2:i) 14. PIP / POP / Twin Picture (Command2:n) G To adjust the screen color. You can also adjust color in the Video menu. G To control the PIP (Picture-in-Picture)/POP/Twin picture. You can also control the PIP/POP/Twin picture using the PIP button on the remote control. Transmission Transmission [k][i][ ][Set ID][ ][Data][Cr] [k][n][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping’. See page 82. Acknowledgement Data 0: PIP off 1: PIP [i][ ][Set ID][ ][OK][Data][x] Acknowledgement 2: POP 3: Twin Picture [n][ ][Set ID][ ][OK][Data][x] 10. Tint (Command2:j) G To adjust the screen tint. You can also adjust tint in the Video menu. 15. PIP Position (Command2:q) G To select sub picture position for PIP. Transmission Transmission [k][q][ ][Set ID][ ][Data][Cr] [k][j][ ][Set ID][ ][Data][Cr] Acknowledgement Data 0: 1: 2: 3: [ j ][ ][Set ID][ ][OK][Data][x] Acknowledgement Data Red : 0 ~ Green : 64 • Refer to ‘Real data mapping’. See page 82. Right down on screen Left down on screen Left up on screen Right up on screen [q][ ][Set ID][ ][OK][Data][x] 11. Sharpness (Command2:k) G To adjust the screen sharpness. You can also adjust sharpness in the Video menu. Transmission 16. Treble (Command2:r) G To adjust treble. You can also adjust treble in the Audio menu. Transmission [k][k][ ][Set ID][ ][Data][Cr] Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping’. See page 82. Acknowledgement [k][ ][Set ID][ ][OK][Data][x] [k][r][ ][Set ID][ ][Data][Cr] Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping’. See page 82. Acknowledgement [r][ ][Set ID][ ][OK][Data][x] 12. OSD Select (Command2:l) G To select OSD (On Screen Display) on/off. 17. Bass (Command2:s) Transmission G To adjust bass. You can also adjust bass in the Audio menu. [k][l][ ][Set ID][ ][Data][Cr] Data 0: OSD off 1: OSD on Transmission [k][s][ ][Set ID][ ][Data][Cr] Acknowledgement [l][ ][Set ID][ ][OK][Data][x] Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping’. See page 82. Acknowledgement 13. Remote Control Lock Mode (Command2:m) [s][ ][Set ID][ ][OK][Data][x] G To lock the remote control and the front panel controls on the set. 18. Balance (Command2:t) G To adjust balance. You can also adjust balance in the Audio menu. Transmission [k][m][ ][Set ID][ ][Data][Cr] Data 0: Lock off 1: Lock on Transmission Acknowledgement [k][t][ ][Set ID][ ][Data][Cr] [m][ ][Set ID][ ][OK][Data][x] Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping’. See page 82. Acknowledgement [t][ ][Set ID][ ][OK][Data][x] Owner’s Manual 83 External Control Device Setup 19. Color Temperature (Command2:u) 24. Orbiter Pixel Setting (Command2:s) G To adjust color temperature. You can also adjust color temperature in the Video menu. G To adjust pixel number in orbiter function. [ j ][s][ ][Set ID][ ][Data][Cr] Transmission [k][u][ ][Set ID][ ][Data][Cr] Data 0: Cool Transmission 1: Medium 2: Warm Acknowledgement [u][ ][Set ID][ ][OK][Data][x] Data Min: 1 ~ Max: A Acknowledgement [s][ ][Set ID][ ][OK][Data][x] 25. Tune Command (Command: m a) G To tune channel to following physical/major/minor number 20. PIP Input Select (Command2:y) G To select input source for sub picture in PIP/Twin picture mode. Transmission [k][y][ ][Set ID][ ][Data][Cr] Data 0: Antenna 1: Cable 2: Video 3: Front Video Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][ ][Data3][ ][Data4][ ][Data5][Cr] Data 0: Physical channel number Min: 1~ Max: 0x87 Data 1, Data 2: Major Channel Number (two part)/ Channel Number (One part) (Data 1: High, Data 2: Low) Data 3, Data 4: Minor Channel Number (Data3: High, Data4: Low) Data 5: Main/Sub 6 Picture Two/One Part Channel Reserved Reserved Step Main Two Sub One 1 NTSC Cable ATSC Air G To avoid having a fixed image remain on screen. ATSC Cable_std ATSC Cable_hrc ATSC Cable_irc 0 ATSC cable Transmission [ j ][p][ ][Set ID][ ][Data][Cr] Acknowledgement [y][ ][Set ID][ ][OK][Data][x] 21. ISM Method (Command2:p) Data 0: Normal 1: Orbiter 2: Inversion NTSC Air Reserved ... Reserved [p][ ][Set ID][ ][OK][Data][x] *All data are transmitted by Hexadecimal code Example) If you want PIP channel tuned to ATSC air (standard) 30-5, the command sequence is ma 00 1e 00 1e 00 05 82. Acknowledgement 22. White Wash (Command2:q) [a][ ][Set ID][ ][OK][Data0][Data1][Data2][Data3][Data4][x] [a][ ][Set ID][ ][NG][Data0][x] Acknowledgement G To control the white wash function on/off. You can also adjust white wash in Option menu. 26. Channel Add/Del (Command: m b) Transmission Transmission G To add and delete the channels [ j ][q][ ][Set ID][ ][Data][Cr] [m][b][ ][Set ID][ ][Data][Cr] Data 0: White Wash off 1: White Wash on Acknowledgement Data 0: Channel Delete 1: Channel Add Acknowledgement [q][ ][Set ID][ ][OK][Data][x] [b][ ][Set ID][ ][OK][Data][x] [b][ ][Set ID][ ][NG][Data][x] 23. Orbiter Time Setting (Command2:r) G To adjust orbiter operation time term. Transmission [ j ][r][ ][Set ID][ ][Data][Cr] Data Min: 1 ~ Max: FE Acknowledgement [r][ ][Set ID][ ][OK][Data][x] 84 Plasma TV 27. Key (Command: m c) G To send IR remote key code Transmission [m][c][ ][Set ID][ ][Data][ ][Cr] Data Key code: Refer to page 86. Acknowledgement [c][ ][Set ID][ ][OK][Data][x] * It’s impossible to command the IR Code 0x08 and 0xC4 with RS-232C. IR Codes IR Codes How to Connect G Connect your wired remote control to the Remote Control port on the TV. Remote Control IR Codes G Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz TC Carrier frequency FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3 T1 G Configuration of frame • 1st frame Lead code Low custom code High custom code Data code Data code C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 • Repeat frame Repeat code Tf G Lead code 9 ms 4.5 ms 0.55 ms G Repeat code 9 ms 2.25 ms G Bit description • Bit “0” • Bit “1” 0.56 ms 0.56 ms 1.12 ms 2.24 ms G Frame interval : Tf The waveform is transmitted as long as a key is depressed. Tf Tf Tf=108ms @455KHz Owner’s Manual 85 IR Codes Code (Hexa) Function 0B TV/VIDEO MODE POWER POWER ON POWER OFF COMP/RGB RATIO TIMER Number Key 0~ 9 - (Dash) FLASHBK MUTE VOL + VOL CH + CH SURF INFO CC 08 C4 C5 98 79 0E 10 ~ 19 4C 1A 09 02 03 00 01 1E AA 39 40 41 07 06 44 43 52 4D 5B 60 72 71 61 63 65 7B 0A CB D6 5A D0 BF D4 D5 D7 C6 76 77 AF 70 96 87 B0 BA B1 BD 8F 8E B2 B3 A9 86 Plasma TV ENTER MENU SOUND VIDEO EXIT PIP PIPCH PIPCH + PIP INPUT SWAP FREEZE ZOOM SAP ADJUST TV VIDEO Front Video COMPONENT 1 COMPONENT 2 RGB-PC RGB-DTV HDMI/DVI Ratio 4:3 Ratio 16:9 Ratio Zoom POP SIGNAL 1394 PLAY PAUSE STOP REC REW FF GOTOPREV GOTONEXT TV GUIDE Note R/C Button R/C Button R/C Button (Power On/Off) Discrete IR Code (Only Power On) Discrete IR Code (Only Power Off) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button Discrete IR Code (TV Input Selection) Discrete IR Code (Video Input Selection) Discrete IR Code (Front Video Input Selection) Discrete IR Code (Component1 Input Selection) Discrete IR Code (Component2 Input Selection) Discrete IR Code (RGB-PC Input Selection) Discrete IR Code (RGB-DTV Input Selection) Discrete IR Code (HDMI/DVI Input Selection) Discrete IR Code (Only 4:3 Mode) Discrete IR Code (Only 16:9 Mode) Discrete IR Code (Only Zoom1 Mode) Discrete IR Code (Channel Search) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button Programming the Remote Programming the Remote G The remote control is a multi-brand or universal remote control. It can be programmed to operate most remote-controllable devices of other manufacturers. Note that the remote control may not control all models of other brands. Programming a code into a remote mode 1. Test your remote control. To find out whether your remote control can operate the component without programming, turn on the component such as a VCR and press the corresponding MODE button (VCR) on the remote control, while pointing at the component. Test the POWER and CH +/- buttons to see if the component responds properly. If not, the remote requires programming to operate the device. 2. Turn on the component to be programmed, then press the corresponding MODE button on the remote control. 3. Press the MENU and MUTE buttons simultaneously, the remote control is ready to be programmed for the code. 4. There are two ways to find the right code for the component. A. If you press the CH +/- buttons repeatedly, the codes will change one at-a-time. Press the POWER button after each code change. If the right code is found, the device will turn off. B. Enter a code number using the number buttons on the remote. Programming code numbers for the corresponding component can be found on the following pages. Again, if the code is correct, the device will turn off. 5. Press the MENU button to store the code. 6. Test the remote control functions to see if the component responds properly. If not, repeat from step 2. Owner’s Manual 87 Programming Codes Programming Codes VCRs Brand Codes Brand Codes Brand Codes Brand Codes AIWA AKAI 034 016 125 072 031 012 035 028 108 003 031 005 065 112 108 012 034 059 006 029 036 129 003 034 031 107 132 012 004 043 031 031 012 040 043 012 048 130 KENWOOD 014 047 001 101 034 003 017 040 031 067 012 069 101 027 031 003 033 101 045 013 013 049 151 034 024 012 048 043 053 066 133 013 063 031 031 067 101 013 PORTLAND PULSAR QUARTZ QUASAR RCA 108 072 011 033 013 040 107 145 003 031 053 058 148 014 032 105 113 125 022 003 102 017 131 003 013 031 101 031 024 003 056 077 034 013 031 067 034 010 TATUNG TEAC TECHNICS TEKNIKA 039 034 031 019 101 034 006 008 059 040 040 012 048 012 040 003 031 053 012 034 058 AMPRO ANAM AUDIO DYNAMICS BROKSONIC CANON CAPEHART CRAIG CURTIS MATHES DAEWOO DAYTRON DBX DYNATECH ELECTROHOME EMERSON FISHER FUNAI GE GO VIDEO HARMAN KARDON HITACHI INSTANTREPLAY JCL JCPENNY JENSEN JVC 043 046 124 146 033 023 037 031 103 039 043 129 033 040 033 007 108 116 135 041 010 064 110 111 117 119 023 039 043 053 027 035 101 153 010 LG (GOLDSTAR) LLOYD LXI MAGIN MAGNAVOX MARANTZ MARTA MATSUI MEI MEMOREX MGA MINOLTA MITSUBISHI 017 031 037 131 008 025 034 046 138 009 033 109 136 045 018 063 033 033 013 066 063 072 144 147 MTC MULTITECH NEC 026 034 137 150 NORDMENDE OPTONICA PANASONIC PENTAX 015 033 101 031 033 043 050 055 060 150 152 PHILCO PHILIPS PILOT PIONEER 034 039 043 048 012 013 020 106 114 123 009 013 014 034 101 106 033 034 041 068 031 033 067 030 033 010 034 102 046 020 020 051 REALISTIC RICO RUNCO SALORA SAMSUNG 014 031 053 072 134 139 059 045 046 059 061 040 034 023 039 043 054 070 074 083 140 145 020 031 033 034 067 033 034 054 071 101 021 048 SANSUI SANYO SCOTT SEARS 010 SHARP SHINTOM SONY SOUNDESIGN STS SYLVANIA SYMPHONIC TANDY 014 066 020 041 109 147 008 033 054 075 033 062 140 145 034 063 144 010 014 034 040 101 THOMAS TMK TOSHIBA TOTEVISION UNITECH VECTOR RESEARCH 040 102 104 107 109 112 115 120 122 043 048 135 007 010 014 134 037 112 129 VICTOR VIDEO CONCEPTS VIDEOSONIC WARDS YAMAHA ZENITH 043 039 043 033 070 031 033 034 013 042 047 082 112 131 101 034 046 013 033 054 034 048 072 017 034 131 039 056 080 024 040 043 101 00 009 014 017 020 042 073 081 054 149 009 031 052 057 058 076 078 149 033 034 059 034 CATV CATV Brand Codes Brand Codes ABC 003 046 112 014 005 026 092 007 007 065 080 019 023 020 057 032 072 008 052 GOLDEN CHANNEL HAMLIN HITACHI HOSPITALITY JERROLD 030 049 052 070 002 009 074 001 037 033 010 100 028 015 073 016 044 100 006 AJIN ANTRONIK ARCHER CABLE STAR CENTURION CENTURY CITIZEN COLOUR VOICE COMBANO COMTRONICS DIAMOND EAGLE EASTERN ELECTRICORD GE GEMINI GI 88 Plasma TV 004 039 042 052 053 007 014 024 090 081 030 030 040 062 066 022 025 054 074 LG (GOLDSTAR) M-NET MACOM MAGNAVOX MEMOREX MOVIE TIME NSC OAK PANASONIC PARAGON PHILIPS 050 055 055 077 003 004 008 010 052 069 106 101 005 012 064 079 032 028 038 071 Brand PIONEER POST NEWS WEEK PRUCER PTS PULSAR RCA REGAL REGENCY REMBRANT RK SAMSUNG SCIENTIFIC ATLANTA 031 037 053 047 012 013 020 SHERITECH SIGNAL SIGNATURE Codes Brand Codes 065 034 076 016 059 011 073 100 047 049 057 025 091 102 003 043 022 030 052 SL MARX SPRUCER STARCOM STARGATE SYLVANIA TADIRAN TAEKWANG TAIHAN TANDY TEXSCAN TOCOM TOSHIBA UNIKA UNITED CABLE UNIVERSAL 030 047 002 008 067 030 110 105 017 029 039 100 007 004 005 026 012 087 100 085 090 051 052 063 048 071 072 074 050 107 030 068 011 041 042 045 046 VIEWSTAR ZENITH 078 004 008 009 030 067 040 056 014 053 007 027 015 088 114 024 014 032 018 089 060 024 035 086 093 Programming Codes HDSTB Brand Codes Brand ALPHASTAR DSR AMPLICA BIRDVIEW BSR CAPETRONICS CHANNEL MASTER 123 050 051 053 053 013 036 008 054 050 005 011 141 024 038 093 097 122 089 EUROPLUS FUJITSU CHAPARRAL CITOH CURTIS MATHES DRAKE DX ANTENNA ECHOSTAR ELECTRO HOME 126 129 014 015 018 055 009 012 077 145 006 007 010 052 112 116 046 040 094 098 056 057 095 099 076 058 096 100 Codes 114 017 133 GENERAL INSTRUMENT 003 031 HITACHI 139 033 HOUSTON TRACKER 057 HUGHES 068 HYTEK 053 JANIEL 060 JERROLD 061 KATHREIN 108 LEGEND 057 LG 001 LUTRON 132 LUXOR 062 MACOM 010 065 021 134 004 059 140 037 104 Brand 022 027 016 029 101 039 051 147 144 059 063 064 Codes MEMOREX NEXTWAVE NORSAT 057 028 069 PACE SKY SATELLITE 143 PANASONIC 060 PANSAT 121 PERSONAL CABLE 117 PHILIPS 071 PICO 105 PRESIDENT 019 PRIMESTAR 030 PROSAT 072 RCA 066 REALISTIC 043 SAMSUNG 123 SATELLITE SERVICE CO 028 085 SCIENTIFIC ATLANTA 032 SONY 103 124 125 070 Brand Codes STARCAST SUPER GUIDE TEECOM 041 020 023 088 137 002 016 044 078 101 135 115 128 081 091 142 TOSHIBA UNIDEN 102 110 111 UNIDEN VIEWSTAR WINEGARD ZENITH 106 074 124 125 026 075 087 090 107 130 127 025 042 043 045 048 049 079 080 086 136 146 082 083 084 120 035 047 057 138 Audio Brand AIWA Codes 014 125 230 AKAI 163 ANAM 003 059 217 BURMECTER 252 CARVER 086 CLARION 199 DAEWOO 027 102 DENON 015 FANTASIA 071 FINEARTS 022 FISHER 089 LG(GOLDSTAR) 001 087 190 211 HAITAI 034 HARMAN/KARDON 068 INKEL 037 078 122 152 157 189 225 247 028 070 096 129 139 229 014 017 023 106 189 216 235 236 Brand Codes JVC KEC KENWOOD 004 185 038 170 215 030 045 014 100 175 179 201 214 238 103 111 002 034 097 049 104 107 046 013 048 133 158 007 142 104 KOHEL NAD LOTTE 053 060 084 148 198 221 075 130 143 099 021 107 191 212 035 024 108 192 239 188 222 058 079 149 153 158 207 226 062 095 150 154 159 222 227 069 121 151 155 160 224 243 029 110 210 LXI MAGNAVOX MARANTZ MCINTOSH MCS MEMOREX NAD ONKYO OPTIMUS PANASONIC PENNEY 013 186 050 171 222 046 016 172 176 180 202 219 240 141 187 067 089 197 206 036 173 177 181 208 223 098 174 178 183 213 232 018 020 025 041 081 090 112 Brand Codes PHILIPS PIONEER 026 039 065 115 113 080 092 103 124 193 204 011 019 106 031 072 156 206 005 044 118 012 076 162 166 205 254 010 185 101 QUASAR RCA RCX REALISTIC SAMSUNG SANSUI SANYO SCOTT SHARP SHERWOOD SONY TAEKWANG 040 041 047 056 057 132 140 033 064 113 220 241 251 TEAC TECHNICS 112 042 091 123 106 145 194 244 135 083 186 032 082 184 209 006 045 126 020 077 163 167 231 143 043 093 127 253 063 094 250 146 195 245 138 234 182 203 246 144 Brand Codes TOSHIBA THE VICTOR WARDS YAMAHA 147 218 137 061 088 131 089 054 055 066 092 199 051 052 117 119 199 200 158 109 248 073 105 164 168 233 114 249 074 161 165 169 242 085 106 136 187 237 113 128 134 DVD Brand Codes Brand Codes Brand Codes Brand Codes APEX DIGITAL DENON GE HARMAN KARDON JVC LG 022 020 014 005 006 027 012 001 010 016 025 MAGNAVOX MARANTZ MITSUBISHI NAD ONKYO PANASONIC 013 024 002 023 008 017 003 009 PHILIPS PIONEER PROCEED PROSCAN RCA SAMSUNG 013 004 021 005 005 011 SONY THOMPSON TOSHIBA YAMAHA ZENITH 007 005 019 009 010 026 006 006 015 006 008 018 016 025 Owner’s Manual 89 Troubleshooting Checklist Troubleshooting Checklist • Check whether the TV is turned on. No picture & No sound • Is the power cord inserted into wall power outlet? • Test the wall power outlet, plug another product’s power cord into the outlet where the TV’s power cord was plugged in. Picture OK & No sound • Press the VOLUME (G) button. • Sound muted? Press MUTE button. • Check to see if there is any object between the TV and the remote control causing obstruction. The remote control doesn’t work • Are batteries installed with correct polarity (+ to +, - to -)? (Refer to p.10) • Correct remote operating mode set: TV, VCR etc.? • Install new batteries. (Refer to p.10) Picture appears slowly after switching on • This is normal, the image is muted during the TV startup process. Please contact your service center, if the picture has not appeared after five minutes. • Select Color in the Video menu and press the VOLUME (G) button. (Refer to p.61) No or poor color or poor picture • Keep a sufficient distance between the TV and the VCR. • Activate any function to restore the brightness of the picture. (If still picture is on the screen for more than 5 minutes, the screen gets dark.) Horizontal/vertical bars or picture shaking • Check for local interference such as an electrical appliance or power tool. No output from one of the speakers • Adjust Balance in the AUDIO menu. (Refer to p.63) Unusual sound from inside the TV • A change in ambient humidity or temperature may result in an unusual noise when the plasma display is turned on or off and does not indicate a fault with the TV. 90 Plasma TV Maintenance Maintenance - Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen 1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen. 2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV. Cleaning the Cabinet To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth. Extended Absence If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges. Owner’s Manual 91 Specification Product Specifications MODELS DU-60PY10 DU-50PY10 Width (inches / mm) 55.2 / 1402 67.24 / 1708 Height (inches / mm) 31.4 / 798.5 36.6 / 931 Depth (inches / mm) 11.9 / 302.5 12.6 / 320.7 Weight (pounds / kg) 122 / 55.3 189.2 / 85.8 Resolution 1024 x 768 (Dot) 1366 x 768 (Dot) Power requirement AC100-240V ~ 60Hz Television System NTSC-M, ATSC Program Coverage VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 135, CADTV 1 ~ 135. DTV 2 ~ 69 External Antenna Impedance 75 Ω Color 16,770,000 (256 steps of each R, G and B) Operating Temperature Range 32 ~ 104°F (0 ~ 40°C) Operating Humidity Range Less than 80% Maximum Elevation 6561 feet (2000m) • The specifications shown above may be changed without prior notice for quality improvement. 92 Plasma TV Notes Owner’s Manual 93 Notes 94 Plasma TV LG ELECTRONICS, INC. PLASMA TV — U.S. LIMITED WARRANTY Your LG Plasma TV will be repaired or replaced in accordance with the terms of this warranty, at LGE’s option, if it proves to be defective in material or workmanship under normal use, during the warranty period (“Warranty Period”) listed below, effective from the date (“Date of Purchase”) of original consumer purchase of the product. This warranty is good only to the original purchaser of the product and effective only when used in the United States, including Alaska, Hawaii, and U.S. Territories. WARRANTY PERIOD: HOW SERVICE IS HANDLED: LABOR and PARTS: 2 YEARS from the Date of Purchase. In-Home Service: Please retain dealer’s Your unit will be repaired or replaced with a new, substitute model or factory reconditioned unit, at LGE’s option. If dated bill of sale or delivery ticket as evidence of the Date of Purchase for proof of warranty, repaired, parts used in the repair may be new or remanufactured. and submit a copy of the bill of sale to the service person at the time warranty service is pro- Replacement Units and Repair Parts are warranted for the remaining portion of the original unit’s warranty period. vided. EFFECTIVE DATE OF WARRANTY: Your warranty period begins on the date of sale to the original consumer/end user. KEEP THE DEALER’S DATED BILL OF SALE OR PROOF OF DELIVERY as evidence of the purchase date. You will be required to submit a legible copy of your bill of sale or proof of delivery when requesting warranty service. Please call 1-201-816-2000 to locate your nearest LGE Authorized Service Center. Visit our website at: http://www.lgservice.com THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. NEITHER THE MANUFACTURER NOR ITS U.S. DISTRIBUTOR SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST PROFITS, LOST OR CORRUPTED PROGRAMMING OR DATA, OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights that vary from state to state. CONCERNING PIXEL FUNCTIONALITY: Your Plasma TV contains about one million individual pixels. Plasma TV typically contain a small number of pixels that do not function normally. Your display has been inspected and is in compliance with manufacturer’s specifications, indicating that any pixel defects do not effect the operation or use of your display. IMPORTANT: Please fill out and mail in your Product Registration Card or go to www.lgservice.com to register your product online. This information will allow us to reach you promptly should we discover a safety or reliability problem that could affect you. THIS LIMITED WARRANTY DOES NOT APPLY TO: ● damage caused in shipping or transit gence, improper maintenance or storage, or to acts ● service required as a result of improper installation, of nature or other causes beyond our control. including incorrect or insufficient AC supply (please consult the owner’s manual for power supply (Causes beyond our control include but are not limited to lightning strike, power surges, power out- ● requirements) installation or repair of antenna systems, cable con- ● verters, cable company supplied equipment, or other components in a video system set-up or adjustment on consumer controls, or ● damage caused by improper adjustments damage caused by other system components ● any panel that has been modified or incorporated ages and water damage.) ● image burn-in repair or replacement of warranted parts by other ● than LGE authorized service centers. units purchased or serviced outside of the coverage ● area. product where the original factory serial numbers ● have been removed, defaced or changed in any way. into any other product ● ● replacement of batteries on the remote control. damage (including cosmetic damage), failure, loss ● product sold and labeled as “as is, where is” or similar disclaimer. or personal injury due to misuse, abuse, negli- The cost of repair or replacement under these excluded circumstances shall be borne by the consumer. CUSTOMER INTERACTIVE CENTER NUMBERS: To obtain customer assistance, product information or Dealer or Service locations Call 1-201-816-2000 24 hours a day, 365 days per year FOR SERVICE: Before you call for warranty service, check your operating guide – you may avoid a service call. For warranty service information, please contact the LGE Customer Interactive Center telephone number. When calling for service, please have your product model number, serial number and the date of purchase or the date of original installation available. If a replacement unit is required, under some circumstances you may be asked to provide a reserve deposit to the LGE Service Center against a credit card number as surety for advanced shipment. Your credit card will not be charged if you return the defective unit within 10 working days. If a replacement unit is received, please use the carton and packaging from that unit in returning the defective unit to the LG®Brand Service Center. Parts and service in accordance with the LGE warranty are LGE’s responsibility and will be provided without charge. Other service requirements will be at the owner’s expense. If you have problems in obtaining satisfactory warranty service, write or call the LGE Customer Interactive Center. Service may be provided by independently owned and operated service organizations. To assure proper credit and avoid unnecessary charges, you must obtain an LGE Return Authorization before returning any product to the LGE Service Center. Contact the Customer Interactive Center for details. TO CONTACT THE LGE CUSTOMER SERVICE CENTER BY MAIL: LGE Customer Interactive Center P.O. Box 240007 201 James Record Road Huntsville, Alabama 35824 http://www.lgservice.com P/NO : 3828VA0479H (3828VB0002L)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 49 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:723d7307-bfa7-4e81-9147-692e8ac0992c Producer : Acrobat Distiller 6.0 (Windows) Modify Date : 2004:10:04 19:55:21+09:00 Create Date : 2004:10:04 19:55:21+09:00 Creator Tool : QuarkXPressª3.3E: LaserWriter 8 Z1-8.7.1 Document ID : uuid:8cf597db-1471-4f6b-85d8-3266de7fb92b Format : application/pdf Title : 479Hen Creator : PSY Author : PSYEXIF Metadata provided by EXIF.tools