LG Electronics USA WB1NP7 Bluetooth Module User Manual
LG Electronics USA Bluetooth Module
User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3263383 |
| Application ID | QtB/orNrqGNOo946X0xdrQ== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 45.11kB (563871 bits) |
| Date Submitted | 2017-01-18 00:00:00 |
| Date Available | 2017-07-17 00:00:00 |
| Creation Date | 2017-01-16 14:17:51 |
| Producing Software | Microsoft® Office Word 2007 |
| Document Lastmod | 2017-01-17 23:09:28 |
| Document Title | User manual |
| Document Creator | Microsoft® Office Word 2007 |
| Document Author: | Yoon |
1. Module : WB1NP7 [Top] [Bottom] This WB1NP7 Module can be easily designed into any embedded system for Bluetooth Spec 4.2 feature. It is based on Airoha’s AB1520 with specific interface design to meet LG Electronics’s needs. 2. Module Specification Chips AB1520 Bluetooth Spec Bluetooth 4.2 Frequency Band 2402 ~ 2480 MHz Tx Power 0.25 ~ 2.5mW (Bluetooth Power Class I) Rx Sensitivity < -70dBm (BER 0.1%) Distance < 100m (Open Space) Power Voltage 3.7V Dimension 20mmⅹ26mm ⅹ3.1 mm Environmental Range Operation temperature -10 ~ 50℃ Modulation GFSK, 8DPSK, π/4-DQPSK Communication Method FHSS 4. Pin Define Symbol Description CMOS input Output No Pin Name I/O Description NC GND GND CONNECTION FOR INTERNAL DIGITAL CIRCUITTRY AND PADS WAKE Input Pin with pull up PIO1 Input only PIO2 Input only NOT CONNECTION 6 PIO3 I/O UART_RX UART_TX PIO11 I/O AIO and I2S_SDI, Alternative function PIO[11] 10 PIO6 I/O I2S_MCLK, Alternative function PIO[6] 11 PIO7 I/O I2S_SCK, Alternative function PIO[7] 12 PIO14 I/O I2S_WS, Alternative function PIO[14] 13 PIO15 I/O I2S_SDO, Alternative function PIO[15] 14 PIO16 I/O I2S_MCLK2, Alternative function PIO[16] 15 PIO17 I/O I2S_SCK2, Alternative function PIO[17] 16 GND 17 SDA I/O I2C DATA LINE 18 SCL I/O I2C CLOCK LINE 19 LED2 LED DRIVER (OPEN DRAIN) 20 LED0 LED DRIVER (OPEN DRAIN) 21 LED1 LED DRIVER (OPEN DRAIN) 22 PIO5 I2S_SDO2, Alternative function PIO[5] 23 VCCIO 1.7~3.6V SUPPLY INPUT FOR PIO 24 PIO12 I/O AIO, Alternative function PIO[17] 25 VREGOUT_MV 26 RESET GOLBAL RESET, ACTIVE HIGH 27 GND GND CONNECTION FOR INTERNAL DIGITAL CIRCUITTRY AND PADS 28 VCHG_IN VCC FOR CHARGER 29 BAT_IN Battery input P 30 VREGOUT_HV LDO OUT(3V3) 31 PIO4 I2S_WS2, Alternative function PIO[4] 32 MIC_BIAS MICROPHONE 1 Bias 33 MIC1_P MICROPHONE 1 P-path I2S_SDI2, Alternative function PIO[3] UART DATA IN UART DATA OUT GND CONNECTION FOR INTERNAL DIGITAL CIRCUITTRY AND PADS LDO OUT(1V8) 34 MIC1_N 35 NC 36 NC 37 LINE_IN_L LINE IN L-path 38 LINE_IN_R LINE IN R-path 39 SPK_LP SPEAKER OUTPUT LP 40 LRVCM SPEAKER OUTPUT LRVCM 41 SPK_RP SPEAKER OUTPUT LP 42 GND GND CONNECTION FOR INTERNAL DIGITAL CIRCUITTRY AND PADS MICROPHONE 1 N-path 5. Mechanical Dimension TOP View Mark Dimension Mark Dimension Mark Dimension Mark Dimension 26.0±0.3 3.01±0.05 0.8±0.2 1±0.1 20.0±0.5 1.27±0.2 0.5±0.2 3±0.3 6.0±0.3 1.20±0.3 0.4±0.1 1.65±0.2 (Unit : mm) 6. Electrical Characteristics Conditions : BAT_P = 4.2V, Ta = 25 ℃, unless otherwise noted. Absolute Maximum Ratings Parameter Min Max Unit Power Supply Voltage : BAT_P -0.3V 4.4V DCV I/O Supply Voltage : VCCIO -0.3V 3.6V DCV -40 85 ℃ Min Max Unit 3.34V 4.2V DCV 60 ℃ Storage Temperature Recommended Operating Conditions Parameter Power Supply Voltage Operation Temperature Current consumption Parameter Inquiry and Page scan, Time interval ACL data transfer Condition Avg Peak Unit mA Master 20 mA Input/Output Characteristics Parameter Min Max Unit VIL Input Voltage Low 0.3*VCCIO VIH Input Voltage High 0.7*VCCIO VCCIO+0.4 VOL Output Voltage Low 0.4 VOH Output Voltage High VCCIO-0.4 General Performance Parameter Condition Frequency Range Min Type 2402 Max 2480 Unit MHz Transmitter Performance Parameter Condition Min Type Max Unit Transmit Power -6 dBm Power density 20 dBm 1000 KHz 20dB bandwidth ±2% -20 dBm ±3% -40 dBm ±4% -40 dBm 30MHz ~ 1GHz -36 dBm 1GHz ~ 12.75GHz -30 dBm 1.8GHz ~ 1.9GHz -47 dBm 5.1GHz ~ 5.3GHz -47 dBm ∆ F1avg 140 175 KHz ∆ F2max 115 KHz ∆ F2avg / ∆ F1avg 80 DH1 packet -40 40 KHz DH5 packet -25 25 KHz Condition Min Type Max Unit Sensitivity 0.1% BER Single slot (DH1 packet) -70 dBm Sensitivity 0.1% BER Multi slot (DH5 packet) -70 dBm -20 dBm -39 dBm Adjacent channel power Out-band Spurious Emission Modulation Characteristic Initial Carrier Frequency Tolerance Carrier Frequency Drift Receiver Performance Parameter Maximum received signal at 0.1% BER Maximum level of intermodulation interferers f1-f2 = 5 MHz, Pwanted= -64 dBm FCC WARNING STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user's authority to operate the equipment. Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Modifications not expressly approved by the manufacturer could void your authority to operate the equipment under FCC rules. FCC RF Radiation Exposure Statement This equipment complies with FCC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Information for OEM integrator The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user manual of the end product. The user manual which is provided by OEM integrators for end users must include the following information in a prominent location. “To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” Label for end product must include “Contains FCC ID: BEJ-WB1NP7, IC: 2703H-WB1NP7" or "A RF transmitter inside, FCC ID: BEJ-WB1NP7, IC: 2703HWB1NP7". IC WARNING STATEMENT This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions : (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This equipment complies with IC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Cet équipement est conforme aux limites établies par Industrie Canada en matière d'exposition aux radiofréquences dans un environnement non contrôlé. Cet appareil et son antenne ne doivent pas être colocalisés ou fonctionner en conjonction avec tout autre antenne ou émetteur. Cet équipement doit être installé et utilisé avec une distance minimale de 20cm entre le radiateur et votre corps.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : Yoon Create Date : 2017:01:16 14:17:51+09:00 Modify Date : 2017:01:17 23:09:28-08:00 Has XFA : No Language : ko-KR Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Creator : Yoon Creator Tool : Microsoft® Office Word 2007 Metadata Date : 2017:01:17 23:09:28-08:00 Producer : Microsoft® Office Word 2007 Document ID : uuid:fdb12028-4727-4f56-bc18-45cb5382ee66 Instance ID : uuid:0ba64c37-844c-4b22-8d76-eafea9ae1ee6 Page Count : 9EXIF Metadata provided by EXIF.tools