LG Electronics USA WB2NB8 Bluetooth Module User Manual
LG Electronics USA Bluetooth Module
User Manual
User Manual PRODUCT NAME : Bluetooth 4.0 Module MODEL NAME : WB2NB8(TWBM-C302D) The information contained herein is the exclusive property of LG Innotek and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of LG Innotek. DOCUMENT No. : - SPECIFICATION REG. DATE : 2017. 10. 18 REV. DATE : 2017. 10. 18 MODEL NAME : WB2NB8(TWBM-C302D) REV. NO : 1.0 PAGE : 1 / 9 Table of Contents No Description Page Features Picture of Product Installation Manual Block Diagram Absolute Maximum Ratings Operating Test Conditions Standard Test Conditions Pin Description Outline Drawing 10 Packing Information Copyrightⓒ. 2017. All Rights Reserved. DOCUMENT No. : - SPECIFICATION REG. DATE : 2017. 10. 18 REV. DATE : 2017. 10. 18 REV. NO : 1.0 MODEL NAME : WB2NB8(TWBM-C302D) PAGE : 2 / 9 1. Features TWBM-C302D is the small size and low power module for Bluetooth 4.0. TWBM-C302D is based on Qualcomm CSR8510A10. Bluetooth 4.0 specification with EDR function / Class 1 Size : 34mm x 19mm x 3.1 mm Internal PCB Printed Antenna USB 2.0 interface Application : DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB 2. Picture of Product < Top > Copyrightⓒ. 2017. All Rights Reserved. < Bottom > DOCUMENT No. : - SPECIFICATION REG. DATE : 2017. 10. 18 REV. DATE : 2017. 10. 18 MODEL NAME : WB2NB8(TWBM-C302D) 3. Installation Manual Install the module like below on the Sound bar Copyrightⓒ. 2017. All Rights Reserved. REV. NO : 1.0 PAGE : 3 / 9 DOCUMENT No. : - SPECIFICATION REG. DATE : 2017. 10. 18 REV. DATE : 2017. 10. 18 REV. NO : 1.0 MODEL NAME : WB2NB8(TWBM-C302D) PAGE : 4 / 9 4. Block Diagram RF LPF 3.3V RAM ROM 2.4GHz Radio I/O USB MMU PIO MCU 26MHz Interface Connector CSR8510 A10 Ant. (2402~2480 MHz) EEPROM 5. Absolute Maximum Ratings Caution : The specifications below the Table define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device. Parameter Min Max Unit Storage Temperature -10 +80 ℃ Storage Humidity (40℃) 90 • Other conditions 1) Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. 2) Store the modules where the temperature and relative humidity do not exceed 5 to 40℃ and 20 to 60%. Copyrightⓒ. 2017. All Rights Reserved. DOCUMENT No. : - SPECIFICATION REG. DATE : 2017. 10. 18 REV. DATE : 2017. 10. 18 REV. NO : 1.0 MODEL NAME : WB2NB8(TWBM-C302D) PAGE : 5 / 9 6. Operating Test Conditions Parameter Min Typ Max Unit Ambient Temperature 60 ℃ Operating Humidity (40℃) 85 Supply Voltage 3.135 3.3 3.465 Vdc 7. Standard Test Conditions The Test for electrical specification shall be performed under the following condition Otherwise this following conditions, not guaranteed this performance. 7-1. Ambient condition Temperature 25 ± 5℃ Humidity 65 ± 5% 7-2. Power supply voltages Input power(VDD) Supply Voltage +3.3V +3.3V ±0.165V(5%) Copyrightⓒ. 2017. All Rights Reserved. DOCUMENT No. : - SPECIFICATION REG. DATE : 2017. 10. 18 REV. DATE : 2017. 10. 18 REV. NO : 1.0 MODEL NAME : WB2NB8(TWBM-C302D) PAGE : 6 / 9 8. Pin Description PIN No. Pin Name Type Pin Description 3.3VA Input 3.3V Power Supply 3.3VA Input 3.3V Power Supply NC GND Ground GND Ground USB+ Input / Output USB Communication signal USB D+ USB- Input / Output USB Communication signal USB D+ GND Ground GND Ground 10 RESET Input Bluetooth Reset 11 BT_WAKEUP Output Bluetooth Host Wake 12 MCU_STBY Input / Output MCU Standby Note. 1) Recommend a Module install sequence for prevent operation failure - Supply 3.3V power - Connect to pins 2) Connector : 12 Pin SMD Connector A Copyrightⓒ. 2017. All Rights Reserved. DOCUMENT No. : - SPECIFICATION REG. DATE : 2017. 10. 18 REV. DATE : 2017. 10. 18 MODEL NAME : WB2NB8(TWBM-C302D) 9. Outline Drawing Copyrightⓒ. 2017. All Rights Reserved. REV. NO : 1.0 PAGE : 7 / 9 DOCUMENT No. : - SPECIFICATION REG. DATE : 2017. 10. 18 REV. DATE : 2017. 10. 18 MODEL NAME : WB2NB8(TWBM-C302D) 10. Packing Information Copyrightⓒ. 2017. All Rights Reserved. REV. NO : 1.0 PAGE : 8 / 9 DOCUMENT No. : - SPECIFICATION REG. DATE : 2017. 10. 18 REV. DATE : 2017. 10. 18 MODEL NAME : WB2NB8(TWBM-C302D) Copyrightⓒ. 2017. All Rights Reserved. REV. NO : 1.0 PAGE : 9 / 9 FCC WARNING STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the user's authority to operate the equipment. Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Modifications not expressly approved by the manufacturer could void your authority to operate the equipment under FCC rules. FCC RF Radiation Exposure Statement This equipment complies with FCC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Information for OEM integrator The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user manual of the end product. The user manual which is provided by OEM integrators for end users must include the following information in a prominent location. “To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” Label for end product must include “Contains FCC ID: BEJ-WB2NB8, IC: 2703H-WB2NB8" or "A RF transmitter inside, FCC ID: BEJ-WB2NB8, IC: 2703HWB2NB8". IC WARNING STATEMENT This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions : (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This equipment complies with IC RF Radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Cet équipement est conforme aux limites établies par Industrie Canada en matière d'exposition aux radiofréquences dans un environnement non contrôlé. Cet appareil et son antenne ne doivent pas être colocalisés ou fonctionner en conjonction avec tout autre antenne ou émetteur. Cet équipement doit être installé et utilisé avec une distance minimale de 20cm entre le radiateur et votre corps.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : Create Date : 2017:10:18 19:49:57Z Modify Date : 2017:11:24 09:37:25+09:00 Subject : Microsoft PowerPoint - 6_WB2NB8(TWBM-C302D)_User_Manual(ENG)_V1-0_171018-ppt [호환 모드] Has XFA : No XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Format : application/pdf Creator : Description : Microsoft PowerPoint - 6_WB2NB8(TWBM-C302D)_User_Manual(ENG)_V1-0_171018-ppt [호환 모드] Title : (Microsoft PowerPoint - 6_WB2NB8\(TWBM-C302D\)_User_Manual\(ENG\)_V1.0_171018.ppt [\310\243\310\257 \270\360\265\345]) Creator Tool : nPDF, http://iblogbox.com/npdf Metadata Date : 2017:11:24 09:37:25+09:00 Keywords : Producer : nPDF, http://iblogbox.com/npdf Document ID : uuid:b6b0e15f-beea-4c4c-bf92-3a195eee268d Instance ID : uuid:6b1a1875-3b8f-4f2b-ab12-092867b93681 Page Count : 12EXIF Metadata provided by EXIF.tools