LG Electronics USA Z47LC6DFUN LCD TV User Manual Zenith US

LG Electronics USA LCD TV Zenith US

Users Manual 1

Installation and Operating GuideModel Numbers | Z42LC6DF, Z47LC6DF | LCD TVENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency (EPA).As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.© Copyright 2008, LG Electronics USA, Inc.
1WARNING / CAUTIONWARNING/CAUTIONTO REDUCE THE RISK OF FIRE AND ELECTRICSHOCK, DO NOT EXPOSE THIS PRODUCT TORAIN OR MOISTURE.TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.WARNING / CAUTIONRISK OF ELECTRIC SHOCK DO NOT OPENThe lightning flash with arrowheadsymbol, within an equilateral triangle, isintended to alert the user to thepresence of uninsulated “dangerous voltage”within the product’s enclosure that may be ofsufficient magnitude to constitute a risk of electricshock to persons.The exclamation point within anequilateral triangle is intended to alertthe user to the presence of important operatingand maintenance (servicing) instructions in theliterature accompanying the appliance.WARNING / CAUTIONTo prevent fire or shock hazards, do not expose thisproduct to rain or moisture.Class B digital deviceThis equipment has been tested and found to complywith the limits for a Class B digital device, pursuant toPart 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmfulinterference in a residential installation. Thisequipment generates, uses and can radiate radiofrequency energy and, if not installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications. However, thereis no guarantee that interference will not occur in aparticular installation. If this equipment does causeharmful interference to radio or television reception,which can be determined by turning the equipmentoff and on, the user is encouraged to try to correctthe interference by one or more of the followingmeasures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.Any changes or modifications not expresslyapproved by the party responsible for compliancecould void the user’s authority to operate theequipment.FCC NOTICEThis reminder is provided to call the CATV systeminstaller’s attention to Article 820-40 of the NationalElectric Code (U.S.A.). The code provides guidelines forproper grounding and, in particular, specifies that thecable ground shall be connected to the grounding systemof the building, as close to the point of the cable entry aspractical.NOTE TO CABLE/TV INSTALLERDo not attempt to modify this product in any waywithout written authorization from LG Electronics.Unauthorized modification could void the user’sauthority to operate this product.CAUTION
2SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONSRead these instructions.Keep these instructions.Heed all warnings.Follow all instructions.Do not use this apparatus near water.Clean only with dry cloth.Do not block any ventilation openings. Install inaccordance with the manufacturer’s instructions.Do not install near any heat sources such asradiators, heat registers, stoves, or other apparatus(including amplifiers) that produce heat.Do not defeat the safety purpose of thepolarized or grounding-type plug. A polarizedplug has two blades with one wider than theother. A grounding type plug has two bladesand a third grounding prong, The wide blade orthe third prong are provided for your safety. Ifthe provided plug does not fit into your outlet,consult an electrician for replacement of theobsolete outlet.Protect the power cord from being walked on orpinched particularly at plugs, conveniencereceptacles, and the point where they exit fromthe apparatus.Only use attachments/accessories specified bythe manufacturer.Use only with the cart, stand, tripod, bracket, ortable specified by the manufacturer, or sold withthe apparatus. When a cart is used, use cautionwhen moving the cart/apparatus combinationto avoid injury from tip-over.Unplug this apparatus during lighting storms orwhen unused for long periods of time.Refer all servicing to qualified service personnel.Servicing is required when the apparatus hasbeen damaged in any way, such as power supplycord or plug is damaged, liquid has been spilledor objects have fallen into the apparatus, theapparatus has been exposed to rain or moisture,does not operate normally, or has beendropped.Never touch this apparatus or antenna during athunder or lighting storm.When mounting a TV on the wall, make sure notto install the TV by the hanging power andsignal cables on the back of the TV.Do not allow an impact shock or any objects tofall into the product, and do not drop onto thescreen with something.CAUTION concerning the Power Cord:It is recommend that appliances be placed upona dedicated circuit; that is, a single outlet circuitwhich powers only that appliance and has noadditional outlets or branch circuits. Check thespecification page of this owner's manual to becertain. Do not connect too many appliances to thesame AC power outlet as this could result in fireor electric shock.
3Do not overload wall outlets. Overloaded walloutlets, loose or damaged wall outlets,extension cords, frayed power cords, ordamaged or cracked wire insulation aredangerous. Any of these conditions could resultin electric shock or fire. Periodically examine thecord of your appliance, and if its appearanceindicates damage or deterioration, unplug it,discontinue use of the appliance, and have thecord replaced with an exact replacement partby an authorized servicer. Protect the powercord from physical or mechanical abuse, such asbeing twisted, kinked, pinched, closed in a door,or walked upon. Pay particular attention toplugs, wall outlets, and the point where thecord exits the appliance.Do not make the TV with the power cordplugged in. Do not use a damaged or loosepower cord. Be sure do grasp the plug whenunplugging the power cord. Do not pull on thepower cord to unplug the TV.WARNING - To reduce the risk of fire or electricalshock, do not expose this product to rain,moisture or other liquids. Do not touch the TVwith wet hands. Do not install this product nearflammable objects such as gasoline or candles orexpose the TV to direct air conditioning.Do not expose to dripping or splashing and donot place objects filled with liquids, such asvases, cups, etc. on or over the apparatus (e.g.on shelves above the unit).GROUNDINGEnsure that you connect the earth ground wire toprevent possible electric shock (i.e. a TV with athree-prong grounded AC plug must be connectedto a three-prong grounded AC outlet). If groundingmethods are not possible, have a qualifiedelectrician install a separate circuit breaker. Do not try to ground the unit by connecting it totelephone wires, lightening rods, or gas pipes.DISCONNECTING DEVICE FROM MAINSMains plug is the disconnecting device. Theplug must remain readily operable.Short-circuit BreakerPower SupplyKeep the product away from direct sunlight.ANTENNASOutdoor antenna groundingIf an outdoor antenna is installed, follow theprecautions below. An outdoor antenna systemshould not be located in the vicinity ofoverhead power lines or other electric light orpower circuits, or where it can come in contactwith such power lines or circuits as death orserious injury can occur.Be sure the antenna system is grounded so as toprovide some protection against voltage surgesand built-up static charges.Section 810 of the National Electrical Code (NEC)in the U.S.A. provides information with respect toproper grounding of the mast and supportingstructure, grounding of the lead-in wire to anantenna discharge unit, size of groundingconductors, location of antenna discharge unit,connection to grounding electrodes andrequirements for the grounding electrode.Antenna grounding according to the NationalElectrical Code, ANSI/NFPA 70CleaningWhen cleaning, unplug the power cord andscrub gently with a soft cloth to preventscratching. Do not spray water or other liquidsdirectly on the TV as electric shock may occur.Do not clean with chemicals such as alcohol,thinners or benzene.MovingMake sure the product is turned off, unpluggedand all cables have been removed. It may take 2or more people to carry larger TVs. Do notpress against or put stress on the front panel ofthe TV.VentilationInstall your TV where there is properventilation. Do not install in a confined spacesuch as a bookcase. Do not cover the productwith cloth or other materials (e.g.) plastic whileplugged in. Do not install in excessively dustyplaces.If you smell smoke or other odors coming fromthe TV or hear strange sounds, unplug thepower cord contact an authorized servicecenter.SAFETY INSTRUCTIONS
4CONTENTSWARNING / CAUTION .................................1SAFETY INSTRUCTIONS .............................2FEATURE OF THIS TV ....................................6PREPARATIONAccessories ......................................................................7Front Panel Information ...............................................8Back Panel Information ................................................9Securing the TV to the Wall to Prevent Falling When the TV is Used on a Stand ...........................11Cable Management ....................................................12Desktop Pedestal Installation ..................................13VESA Wall Mounting ..................................................13Antenna or Cable Connection ................................ 14EXTERNAL EQUIPMENT SETUPHD Receiver Setup .....................................................15DVD Setup ...................................................................18VCR Setup .................................................................... 20Other A/V Source Setup ..........................................22PC Setup .......................................................................23Audio Out Connection ..............................................28WATCHING TV / CHANNEL CONTROLRemote Control Functions .......................................30Turning On TV ............................................................32Channel Selection .......................................................32Volume Adjustment ....................................................32On-Screen Menus Selection ....................................33Channel Setup .............................................................34- Auto Scan (Auto Tuning) ..................................34- Add/Delete Channel (Manual Tuning) ..........35- Channel Editing ...................................................36Input List ....................................................................... 37Input Label ...................................................................38Key Lock .......................................................................39PICTURE CONTROLPicture Size (Aspect Ratio) Control .......................40Preset Picture Settings ..............................................41- Picture Mode - Preset ........................................41- Color Tone - Preset ............................................42Manual Picture Adjustment ......................................43- Picture Mode - User Mode ...............................43- Color Tone - User Mode ...................................44DB - Picture Improvement Technology .................45Advanced - Cinema 3:2 Pulldown Mode ...............46Advanced - Black (Darkness) Level ........................47Picture Reset ................................................................48SOUND & LANGUAGE CONTROLAuto Volume Leveler (Auto Volume) .....................49Preset Sound Settings (Sound Mode) ..................50Sound Setting Adjustment - User Mode ...............51Balance ..........................................................................52TV Speakers On/Off Setup ......................................53Stereo/SAP Broadcasts Setup .................................54Audio Language ...........................................................55On-Screen Menus Language Selection ..................56Caption Mode ..............................................................57- Analog Broadcasting System Captions ..........58- Digital Broadcasting System Captions ..........59- Caption Option ....................................................60
5TIME SETTINGClock Setting ............................................................... 61- Auto Clock Setup ................................................ 61- Manual Clock Setup ........................................... 62Auto On/Off Timer Setting ..................................... 63Sleep Timer Setting ................................................... 64Auto Shut-off Setting ................................................ 65PARENTAL CONTROL / RATINGSSet Password & Lock System .................................. 66Channel Blocking ........................................................ 68External Input Blocking ............................................. 68Movie & TV Rating .................................................... 69APPENDIXTroubleshooting ......................................................... 72Maintenance ................................................................ 74Product Specifications .............................................. 75Programming the Remote Control ......................... 76IR Codes ....................................................................... 80External Control Through RS-232C ..................... 82Open Source Software License ............................... 89
6FEATURE OF THIS TVIf the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there isnothing wrong with TV.Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, theyhave no adverse effect on the monitor's performance.Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so mayproduce some temporary distortion effects on the screen.On DisposalThe fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority. is a trademark of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc.LG TV with this logo displays Full HD (high-definition) 1080p native resolution by receiving and processing a Full HD 1080p signal.It has three HDMI ports that connect audio and video devices with one cable and produces the highest quality digital images and sound.Manufactured under license from Dolby Laboratories. “Dolby “and the double-D symbol are trademarks of Dolby Laboratories.High-definition television. High-resolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080i and 720p resolutions.
7PREPARATIONPREPARATIONACCESSORIESEnsure that the following accessories are included with your TV. If an accessory is missing, please contact thedealer where you purchased the TV.The accessories included may differ from the images below.Owner’s Manual CD Manual Remote ControlPower Cord Batteries Cable Management ClipPolishing Cloth* Wipe spots on the exterior onlywith the polishing cloth.* Do not wipe roughly whenremoving stain. Please be cautionsof that excessive pressure maycause scratch or discoloration. D-sub 15 pin CableWhen using the VGA (D-sub 15 pincable) PC connection, the user mustuse shielded signal interface cableswith ferrite cores to maintainstandards compliance.Option Extras
8PREPARATIONPREPARATIONFRONT PANEL INFORMATIONHere shown may be somewhat different from your TV.NOTE: If your product has a protection tape attached, remove the tape.And then wipe the product with a cloth (If a polishing cloth is included with your product, use it).CHANNEL (S, T)ButtonsVOLUME (W, X)ButtonsENTER ButtonMENU ButtonINPUT ButtonPOWER ButtonPower/Standby Indicator• Illuminates red in standby mode.• Illuminates green when the set is switched on.Remote Control Sensor
9PREPARATIONBACK PANEL INFORMATIONHere shown may be somewhat different from your TV.
10PREPARATIONPREPARATIONHDMI/DVI INConnect a HDMI signal to 1, 2 or 3.Or DVI (VIDEO) signal to the 1, 2 or 3 port with a DVI to HDMI cable.COMPONENT INAnalog Connection.Supports HD.Uses a red, green, and blue cable for video & red and white for audio.RGB (PC)Analog PC Connection. Uses a D-sub 15 pin cable (VGA cable).AUDIO (RGB/DVI)1/8” headphone jack for analog PC audio input.REMOTE CONTROL PORTFor a wired remote control.RS-232C IN (CONTROL & SERVICE) PORTUsed by third party devices.ANTENNA/CABLE INConnect over-the air signals to this jack.Connect cable signals to this jack.DIGITAL AUDIO OUTConnect digital audio to various types of equipment.Note: In standby mode, these ports do not work.AUDIO OUTAnalog audio output for use with amps and home theater systems.AV (Audio/Video) INAnalog composite connection. Supports standard definition video only (480i).S -VIDEOBetter quality than standard composition.Supports standard definition video only (480i).USB INPUTPower Cord SocketFor operation with AC power.Caution: Never attempt to operate the TV onDC power.
11PREPARATIONSECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STANDYou should purchase necessary components to prevent TV from falling off of the stand.Image shown may differ from your TV.We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,potentially causing injury or damaging the product.Caution: Please make sure that children don’t climb on or hang from the TV.Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that ismounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely.NOTEXUse a platform or cabinet strong enough and large enough to support the size and weight of the TV.XTo use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.Use a sturdy rope (sold separately) to tie the product. It is safer to tiethe rope so it becomes horizontal between the wall and the product.!
12PREPARATIONPREPARATIONCABLE MANAGEMENTHere shown may be somewhat different from your TV.Connect the cables as necessary.To connect an additional equipment, see the EXTERNAL EQUIPMENT SETUP section.Install the CABLE MANAGEMENT CLIP as shown.How to remove the CABLE MANAGEMENT CLIPXHold the CABLE MANAGEMENT CLIP with both hands and pull it backward.CABLE MANAGEMENT CLIPNOTEXDo not hold the CABLE MANAGEMENT CLIP when moving the product.- If the product is dropped, you may be injured or the product may be broken.!
13PREPARATIONDESKTOP PEDESTAL INSTALLATIONFor proper ventilation, allow a clearance of 4 inches on all four sides from the wall.VESA WALL MOUNTINGThis TV accepts VESA FDMI compliant mounts via the four screw holes on the back of the TV.We recommend that you use a wall mounting bracket of LG brand when mounting the TV to a wall.CAUTION XEnsure adequate ventilation by following the clearance recommendations.NOTEXScrew length needed depends on the wall mount used. For further information, refer to the instructions included with the mount.4 inches4 inches4 inches4 inches600 mm400 mm!
14PREPARATIONPREPARATIONANTENNA OR CABLE CONNECTIONTo prevent damage do not connect to the power outlet until all connections are made between the devices.1. Antenna (Analog or Digital)Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections.For optimum picture quality, adjust antenna direction if needed.2. CableTo improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.If the antenna is not installed properly, contact your dealer for assistance.Wall Antenna SocketOutdoor Antenna (VHF, UHF)Multi-family Dwellings/Apartments (Connect to wall antenna socket)RF Coaxial Wire (75 ohm)Single-family Dwellings/Houses (Connect to wall jack for outdoor antenna) Copper WireBe careful not to bend the copper wire when connecting the antenna.Cable TV Wall JackRF Coaxial Wire (75 ohm)
15EXTERNAL EQUIPMENT SETUPEXTERNAL EQUIPMENT SETUPTo prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.HD RECEIVER SETUPThis TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you doreceive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.Component Connection12Y L RPBPR1. How to connect2. How to useTurn on the digital set-top box.(Refer to the owner’s manual for the digital set-top box operation)Select the Component 1 input source on the TV using the INPUT button on the remote control.If connected to COMPONENT IN 2 input, select the Component 2 input source on the TV.Connect the video outputs (Y, PB, PR) of the digital settop box to the COMPONENT IN VIDEO 1 jacks onthe set. Match the jack colors (Y = green, PB = blue,and PR = red).Connect the audio output of the digital set-top box tothe COMPONENT IN AUDIO 1 jacks on the TV.Supported Resolutions Y, CB/PB, CR/PRSignal Component 1/2 HDMI1, 2 or 3480i Yes No480p Yes Yes720p Yes Yes1080i Yes Yes1080p Yes YesResolution Horizontal Frequency (KHz)Vertical Frequency (Hz)720x480i 15 . 7315 . 7359.9460.00720x480p 31 . 4731 . 5059.9460.001280x720p 44.9645.0059.9460.001920x1080i 33.7233.7559.9460.001920x1080p26.9727.0033.7133.7567.43267.5023.97624.0029.9730.0059.93960.00
16EXTERNAL EQUIPMENT SETUPEXTERNAL EQUIPMENT SETUPHDMI Connection1. How to connect2. How to useTurn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)Select the HDMI1, HDMI2 or HDMI3 input source on the TV using the INPUT button on the remote control.Connect the digital set-top box to HDMI/DVI IN 1 , 2or 3 jack on the TV.No separated audio connection is necessary. HDMI supports both audio and video.HDMI-DTV modeResolution Horizontal Frequency (KHz)Vertical Frequency (Hz)720x480p 31 . 4731 . 5059.9460.001280x720p 44.9645.0059.9460.001920x1080i 33.7233.7559.9460.001920x1080p26.9727.0033.7133.7567.43267.5023.97624.0029.9730.0059.93960.00
17EXTERNAL EQUIPMENT SETUPDVI to HDMI Connection1. How to connect2. How to useTurn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)Select the HDMI1 input source on the TV using the INPUT button on the remote control.Connect the DVI output of the digital set-top box to the HDMI/DVI IN 1, 2 or 3 jack on the TV.Connect the audio output of the digital set-top box to the AUDIO (RGB/DVI) jack on the TV.NOTE XA DVI to HDMI cable or adapter is required for this connection. DVI doesn't support audio, so a separate audio connection is necessary.!
18EXTERNAL EQUIPMENT SETUPEXTERNAL EQUIPMENT SETUPDVD SETUPComponent ConnectionComponent Input portsTo get better picture quality, connect a DVD player to the component input ports as shown below.Y L RPBPR1. How to connect2. How to useTurn on the DVD player, insert a DVD.Select the Component 1 input source on the TV using the INPUT button on the remote control.If connected to COMPONENT IN 2 input, select the Component 2 input source on the TV.Refer to the DVD player's manual for operating instructions.Connect the video outputs (Y, PB, PR) of the DVD tothe COMPONENT IN VIDEO 1 jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red).Connect the audio outputs of the DVD to theCOMPONENT IN AUDIO 1 jacks on the TV.Component ports on the TV Y PBPRVideo output ports on DVD playerY PBPRYB-Y R-YYCb CrYPb Pr
19EXTERNAL EQUIPMENT SETUPS-Video ConnectionHDMI Connection1. How to connect2. How to useTurn on the DVD player, insert a DVD.Select the AV 1 input source on the TV using the INPUT button on the remote control.If connected to AV IN2, select AV 2 input source.Refer to the DVD player's manual for operating instructions.Connect the S-VIDEO output of the DVD to the S -VIDEO input on the TV.Connect the audio outputs of the DVD to the AUDIOinput jacks on the TV.1. How to connect2. How to useSelect the HDMI1, HDMI2 or HDMI3 input source on the TV using the INPUT button on the remote control.Refer to the DVD player's manual for operating instructions.Connect the HDMI output of the DVD to the HDMI/DVI IN 1, 2 or 3 jack on the TV.No separated audio connection is necessary.HDMI supports both audio and video.
20EXTERNAL EQUIPMENT SETUPEXTERNAL EQUIPMENT SETUPVCR SETUPTo avoid picture noise (interference), leave an adequate distance between the VCR and TV.If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. This phenomenon is common to all TVs and is not covered by warranty.Antenna Connection1. How to connect2. How to useSet VCR output switch to 3 or 4 and then tune TV to the same channel number.Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)Connect the RF antenna out socket of the VCR to the ANTENNA/CABLE IN socket on the TV.Connect the antenna cable to the RF antenna in socket of the VCR.Wall JackAntenna
21EXTERNAL EQUIPMENT SETUPNOTE XIf you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the set.L RComposite (RCA) Connection1. How to connect2. How to useInsert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)Select the AV 1 input source on the TV using the INPUT button on the remote control.If connected to AV IN2, select AV 2 input source.Connect the AUDIO/VIDEO jacks between TV andVCR. Match the jack colors (Video = yellow, Audio Left= white, and Audio Right = red)!( )L RS-Video Connection1. How to connect2. How to useInsert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)Select the AV 1 input source on the TV using the INPUT button on the remote control.If connected to AV IN2, select AV 2 input source.Connect the S-VIDEO output of the VCR to the S -VIDEO input on the TV.Connect the audio outputs of the VCR to the AUDIOinput jacks on the TV.CAUTIONXDo not connect to both Video and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work.NOTEXS-Video provides better quality than composite. Use it when available.!
22EXTERNAL EQUIPMENT SETUPEXTERNAL EQUIPMENT SETUPOTHER A/V SOURCE SETUP1. How to connect2. How to useSelect the AV 2 input source on the TV using the INPUT button on the remote control.If connected to AV IN1 input, select AV 1 input source.Operate the corresponding external equipment.Connect the AUDIO/VIDEO jacksbetween TV and external equipment. Match the jack colors. (Video = yellow, Audio Left = white,and Audio Right = red)CamcorderVideo Game Set
23EXTERNAL EQUIPMENT SETUPPC SETUPThis TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.VGA (D-Sub 15 pin) Connection1. How to connect2. How to useTurn on the PC and the TV.Select the RGB-PC input source on the TV using the INPUT button on the remote control.Connect the VGA output of the PC to the RGB (PC) jackon the TV.Connect the PC audio output to the AUDIO (RGB/DVI)jack on the TV.
24EXTERNAL EQUIPMENT SETUPEXTERNAL EQUIPMENT SETUPDVI to HDMI Connection1. How to connect2. How to useTurn on the PC and the TV.Select the HDMI1, HDMI2 or HDMI3 input source on the TV using the INPUT button on the remote control.Connect the DVI output of the PC to the HDMI/DVI IN 1, 2 or 3 jack on the TV.Connect the PC audio output to the AUDIO (RGB/DVI) jack on the TV.
25EXTERNAL EQUIPMENT SETUPSupported Display SpecificationsRGB-PC, HDMI-PC mode NOTES!XTo get the the best picture quality, adjust the PC graphics card to 1920x1080.XDepending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use.XIn PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.XAvoid keeping a fixed image on the screen for a long period of time. The fixed image could become permanently imprinted on the screen.XThe synchronization input form for Horizontal and Vertical frequencies is separate.XDepending on the graphics card, some resolution settings may not allow the image to be positioned on the screen properly.Resolution Horizontal Frequency (KHz)Vertical Frequency (Hz)640x350 31.468 70.09720x400 31.469 70.08640x48031 . 46937.50037.86159.9475.0072.80800x60035.15637.87946.87548.07756.2560.3175.0072.181024 x 76848.36356.47660.02360.0070.0675.021280x768 47.77660.28959.8774.8931280x1024 63.98179.97660.0275.025136 0 x 768 47. 712 6 0 . 0151600x1200 75.00 60.001920x1080 67.50 60.00* RGB-PC mode onlyNOTEXDepending on graphic card and signal status, there can be some shaking to find best picture in a little time.!
26EXTERNAL EQUIPMENT SETUPEXTERNAL EQUIPMENT SETUPScreen Setup for PC modeOverviewWhen the RGB input of the set is connected to a PC Output,Select RGB-PC using the INPUT button on the remotecontrol.When you change the resolution, select the properresolution in present input to see the best pictureappearance.Adjustment for screen Resolution, Position, Size, and PhasePress the MENU button and then use 1 or 2 buttonto select the PICTURE menu.Press the 4 button and then use 1 or 2 button toselect Screen.Press the 4 button and then use 1 or 2 button toselect Resolution, Position, Size, or Phase.Press the ENTER button and then use 1 2 3 4button to make appropriate adjustments.The Phase adjustment range is -16 ~ +16.The Size adjustment range is -30 ~ +30.Press RETURN button to return to normal viewing orpress MENU button to return to the previous menu.ResolutionResolutionSizePhaseReset1024 x 7681280 x 7681360 x 7681366 x 768MENU Prev Select OkScreenPicture ModeColor TemperatureDBAdvancedAspect RatioPicture Reset: User1: Cool: 16:9ScreenPicture ModeColor TemperatureDBAdvancedAspect RatioPicture ResetSelection (X or ) leads you to the screen adjustment menu.Resolution This function allows you select resolution of XGA/WXGA.Position This function is to adjust picture to left/right and up/down as you prefer.Size This function is to minimize any vertical bars or stripesvisible on the screen background. And the horizontalscreen size will also change.Phase This function allows you to remove any horizontal noiseand clear or sharpen the image of characters.
27EXTERNAL EQUIPMENT SETUPInitializing (Reset to original factory values)To initialize the adjusted values.PositionResolutionSizePhaseResetInitialize Settings.MENU Prev Select OkYes NoPress the MENU button and then use 1 or 2 buttonto select the PICTURE menu.Press the 4 button and then use 1 or 2 button toselect Screen.Press the 4 button and then use 1 or 2 button toselect Reset.Press the ENTER button and then use 3 or 4 buttonto select Yes .Press the ENTER button.ScreenPicture ModeColor TemperatureDBAdvancedAspect RatioPicture Reset: User1: Cool: 16:9ScreenPicture ModeColor TemperatureDBAdvancedAspect RatioPicture ResetSelection (X or ) leads you to the screen adjustment menu.
28EXTERNAL EQUIPMENT SETUPEXTERNAL EQUIPMENT SETUPAUDIO OUT CONNECTIONSend the TV’s audio to external audio equipment via the Audio Output port.Analog1. How to connectConnect audio outputs to the TV’s AUDIO OUT jacks.Set the “TV Speaker option - Off” in the AUDIO menu.(Xp.53). See the external audio equipment instructionmanual for operation.

Navigation menu