LG Innotek RNTDST01A IP Camera User Manual

LG Innotek Co., Ltd. IP Camera

User manual

REGULATION INFORMATION TO THE USER (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment. This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. A minimum separation distance of 20 ㎝ must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements. Home Security Camera REGULATION INFORMATION TO THE USER (IC) Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps 1. Product & Accessories2. Operating Condition - IP Network Camera : 32℉~104℉ 3. Wall mount InstallationIP Network Camera, Adapter, Ethernet to Micro USB Cable Anchor & Screw Quick Manual Non-slip pad 1. Tighten two screws to fix the bracket on the wall using screw driver.2.Push and lock stand body to the bracket .This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:(1) this device may not cause interference, and(2) this device must accept any interference, including interference that may cause undesired operation of the device.This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
6. Mount SD Card(Optional)Press and hold ‘Reset’ button more than 10 seconds until blink red of Network LED Reset Button 표현 그림 필요 9. Caution1) This camera is an indoor good.(Don’t install outdoor)2) Don’t cover vent hole3) Don’t drop water or chemical substance.4) Strong light is a cause of some image quality problem.(sun light, headlight form automobiles, etc.)Reset 5. Pairing the Device4. Table-top installation1. Attach the non-slip pad under mount bracket and lock thecamera body.2. Adjust thecamera view direction8. Factory ResetLED Status Description Camera Power LED Blinking Green Firmware updating Pulsing Amber Connecting to Server Pulsing Green Booting Solid Amber No Connectivity to Server Solid Green Working Solid Red Malfunction Off Power Off Camera Network LED Pulsing Green Connecting to Router Pulsing Red No Connectivity to Router Solid Green Network Working Solid Red Network Working with weak signal (RSSI < -80) Off Network Disabled Camera Video LED Solid Green Recording Off Camera not Working 1. Plug in the camera.2. Connect ethernet cable to controller ethernet port.3. Please follow instructions on their controller.Camera Video Led 7. LED Descriptioin1. Insert a micro SD memory(be careful memory up/down side)Camera Power Led Camera Network Led

Navigation menu