LG Innotek TWFMB005D Wi-Fi Module User Manual
LG Innotek Co., Ltd. Wi-Fi Module Users Manual
Users Manual
SPECIFICATIONS PRODUCT NAME : Dual Band 2T2R MIMO Wi-Fi Module MODEL NAME TWFM-B005D The information contained herein is the exclusive property of LG Innotek and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of LG Innotek. This module will be installed in only TV for Wi-Fi communication. (00)-0073 DOCUMENT No : REG. DATE : 2011.10.22 SPECIFICATION REV. DATE : 2011.10.22 MODEL NAME : TWFM-B005D HC40787 REV.NO : 1.1 PAGE : 1 / 16 Change History of Revision Revision 1.0 Date Contents of Revision Change ’11.10.22 First release ©2011 LGIT. All rights reserved. Remark Lee DOCUMENT No : REG. DATE : 2011.10.22 SPECIFICATION REV. DATE : 2011.10.22 MODEL NAME : TWFM-B005D HC40787 REV.NO : 1.1 PAGE : 2 / 16 Table of Contents No Description Page F t Features Ordering Information Block Diagram Absolute Maximum Ratings Operating Conditions Standard Test Conditions Electrical Specifications Environment Tests 11 Pin Description 12 10 S/W 13 11 Assembly Drawing 14 12 Packing Information 15 ©2011 LGIT. All rights reserved. DOCUMENT No : REG. DATE : 2011.10.22 SPECIFICATION REV. DATE : 2011.10.22 MODEL NAME : TWFM-B005D HC40787 REV.NO : 1.1 PAGE : 3 / 16 1. Features TWFM-B005D is the small size and low power module for IEEE 802.11a/b/g/n wireless LAN. TWFM-B005D is based on Broadcom BCM43236B solution. IEEE 802.11 a/b/g/n Dual Band WLAN infrastructure Size : 90mm x 16mm x 6.45mm 2.4GHz and 5GHz internal PA Two stream spatial multiplexing up to 300Mbps PIFA ANT (2T2R MIMO) Use on-chip OTP (One-Time Programmable) USB 2.0 Supports drivers for Windows Vista, 2000, XP, Linux Security : WPA,WPA2,AES(TKIP) ,IEEE 802.1X • Application: DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB 2. Ordering Information Model Description TWFM B005D TWFM-B005D Wi Fi Mod Wi-Fi Module, le Dual D al Band 2T2R MIMO ©2011 LGIT. All rights reserved. DOCUMENT No : REG. DATE : 2011.10.22 SPECIFICATION REV. DATE : 2011.10.22 MODEL NAME : TWFM-B005D HC40787 REV.NO : 1.1 PAGE : 4 / 16 3. Block Diagram BCM43236B RF Switch+ diplexer 2.4GHz PA 5GHz PA 2x2 Radio 802.11n PHY System Bus 802.11n MAC ANT Security OTP(2K bits) 384K Memory USB 2 2.0 0 or HSIC USB Connector ANT GPIO ARM Cortex M3 CPU 3.3V 1.2V DC-DC Main Clock(20MHz) 5V < Fig.1 Hardware Block Diagram > 4. Absolute Maximum Ratings Caution : The specifications in Table 1 define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device. Parameter Min Max Unit Storage Temperature -10 +80 ℃ Storage Humidity (40℃) 90 < Table 1 Absolute Maximum Ratings g > . Other conditions 1) Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. 2) Store the modules where the temperature and relative humidity do not exceed 5 to 40℃ and 20 to 60%. 3) Assemble the modules within 6 months. Check the soldering ability in case of 6 months over. ©2011 LGIT. All rights reserved. DOCUMENT No : REG. DATE : 2011.10.22 SPECIFICATION REV. DATE : 2011.10.22 MODEL NAME : TWFM-B005D HC40787 REV.NO : 1.1 PAGE : 5 / 16 5. Operating Conditions Parameter Min Typ Max Unit Operating Temperature -10 +60 ℃ Operating Humidity 85 4.5 5.0 5.5 Vdc Supply Voltage VDD_5V 6. Standard Test Conditions The Test for electrical specification shall be performed under the following condition unless otherwise specified. 1). Ambient condition . Temperature . Humidity 25℃ ± 5℃ 65% ± 5% R.H. 2). Power supply voltages . 5V (±5%) input power at the Module 3). Current consumption over recommended range of supply voltage and operating conditions is like below. When it’s tested, it must be supplied more than 2 times of maximal current. FCC (Federal Communications Commission) WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions: 1. This device may not cause harmful interference, and 2. This device must accept ant interference received, including interference that may cause undesirable operation. To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product. Contains Transmitter module FCC ID: YZP-TWFMB005D The antenna must be installed such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna. End users cannot modify this transmitter device. Any Unauthorized modification could void the user`s authority to operate this device. ©2011 LGIT. All rights reserved. DOCUMENT No : REG. DATE : 2011.10.22 SPECIFICATION REV. DATE : 2011.10.22 MODEL NAME : TWFM-B005D HC40787 REV.NO : 1.1 PAGE : 6 / 16 7. Electrical Specifications 1) DC Characteristics Current Consumption Min. Typ. Max. TX M Mode d ( MCS7) 470 Idle and Associated state 215 Radio disabled state 100 Unit mA 2) RF Characteristics for IEEE802.11b ( 11Mbps mode unless otherwise specified) Items Contents Specification IEEE802.11b Mode DSSS/CCK Channel frequency 2400 ~ 2483 MHz Data rate 1,2,5.5,11Mbps TX Characteristics Min. Typ. Max. Unit 13 15 17 dBm 1st side lobes ( to fc ±11MHz) -43 -30 dBr 2nd side lobes ( to fc ±22MHz) -58 -50 dBr Modulation Accuracy (EVM) 30 35 Power On/Off ramp 0.5 2.0 usec Freq. Tolerance -25 25 ppm Chip Clock Freq. Tolerance -25 25 ppm Min. Typ. Max. Unit -88 88 -76 76 dBm dBm Power Level Spectrum Mask RX Characteristics Minimum Input Level Sens Sens. (FER ≤ 8%) Maximum Input Level (FER ≤ 8%) * Normal Condition : 25℃, VDD=5V. ©2011 LGIT. All rights reserved. -10 DOCUMENT No : REG. DATE : 2011.10.22 SPECIFICATION REV. DATE : 2011.10.22 MODEL NAME : TWFM-B005D HC40787 REV.NO : 1.1 PAGE : 7 / 16 3) RF Characteristics for IEEE802.11g ( 54Mbps mode unless otherwise specified) Items Contents Specification ifi ti IEEE502 11 IEEE502.11g Mode OFDM Channel frequency 2400 ~ 2483.5 MHz , , , , , , , 6,9,12,18,24,36,48,54Mbps Data rate Min. Typ. Max. Unit 13 15 17 dBm at fc ±11MHz -32 -20 dBr at fc ±20MHz -43 -28 dBr at fc ≥ ± 30MHz -48 -40 dBr -34 -25 dB Freq. Tolerance -20 20 ppm Chip Clock Freq. Tolerance -20 20 ppm RX Characteristics Min. Typ. Max. Unit Minimum Input Level Sens. (PER ≤ 10%) -75 -65 dBm -20 dBm TX Characteristics Power Level Spectrum Mask Constellation Error (EVM) Maximum Input Level (PER ≤ 10%) * Normal Condition : 25℃ 25℃, VDD=5V. VDD=5V ©2011 LGIT. All rights reserved. DOCUMENT No : REG. DATE : 2011.10.22 SPECIFICATION REV. DATE : 2011.10.22 MODEL NAME : TWFM-B005D HC40787 REV.NO : 1.1 PAGE : 8 / 16 4) RF Characteristics for IEEE802.11a ( 54Mbps mode unless otherwise specified) Items Contents Specification ifi ti IEEE802.11a IEEE802 11 Mode OFDM 5150~5250MHz, 5725 ~ 5850MHz Channel frequency Data rate 6,9,12,18,24,36,48,54Mbps TX Characteristics Min. Typ. Max. Unit 11 13 15 dBm at fc ±11MHz -32 -20 dBr at fc ±20MHz -43 -28 dBr at fc ≥ ± 30MHz -48 -40 dBr -34 -25 dB Freq. Tolerance -20 20 ppm Chip Clock Freq. Tolerance -20 20 ppm RX Characteristics Min. Typ. Max. Unit Minimum Input Level Sens. (PER ≤ 10%) -72 -65 dBm -30 dBm Power Level Spectrum Mask Constellation Error (EVM) Maximum Input Level (PER ≤ 10%) * Normal Condition : 25℃, VDD=5V. ©2011 LGIT. All rights reserved. DOCUMENT No : REG. DATE : 2011.10.22 SPECIFICATION REV. DATE : 2011.10.22 MODEL NAME : TWFM-B005D HC40787 REV.NO : 1.1 PAGE : 9 / 16 5) RF Characteristics for IEEE802.11an ( MCS7 mode unless otherwise specified) Items Contents Specification ifi ti IEEE802 11 – 5GHz IEEE802.11n 5GH Mode OFDM 5150~5250MHz, 5725 ~ 5850MHz Channel frequency ~135Mbps Data rate Min. Typ. Max. Unit 11 13 15 dBm at fc ±11MHz -32 -20 dBr at fc ±20MHz -35 -28 dBr at fc ±30MHz -45 -40 dBr -32 -28 dB Freq. Tolerance -20 20 ppm Chip Clock Freq. Tolerance -20 20 ppm Min. Typ. Max. Unit Minimum Input Level Sens. (HT20,PER ≤ 10%) -71 -64 dBm Minimum Input Level Sens. ((HT40,PER ≤ 10%)) -68 -61 dBm -30 dBm TX Characteristics Power Level (HT20 / HT40 : MCS7) Spectrum Mask (HT20) Constellation Error (EVM) RX Characteristics Maximum Input Level (PER ≤ 10%) * Normal Condition : 25℃, VDD=5V. ©2011 LGIT. All rights reserved. DOCUMENT No : REG. DATE : 2011.10.22 SPECIFICATION REV. DATE : 2011.10.22 MODEL NAME : TWFM-B005D HC40787 REV.NO : 1.1 PAGE : 10 / 16 6) RF Characteristics for IEEE802.11gn ( MCS7 mode unless otherwise specified) Items Contents Specification ifi i IEEE802 11 – 2.4GHz IEEE802.11n 2 4GH Mode OFDM Channel frequency 2400 ~ 2483.5 MHz Data rate 6 5 13 19 5 26 39 52 58 5 65Mbps 6.5,13,19.5,26,39,52,58.5,65Mbps TX Characteristics Min. Typ. Max. Unit 11 13 15 dBm at fc ±11MHz -32 -20 dBr at fc ±20MHz -35 -28 dBr at fc ±30MHz -45 -40 dBr -32 -28 dB Freq. Tolerance -20 20 ppm Chip Clock Freq. Tolerance -20 20 ppm Min. Typ. Max. Unit Minimum Input Level Sens. (HT20,PER ≤ 10%) -73 -64 dBm Minimum Input Level Sens. (HT40,PER ≤ 10%) -70 -62 dBm -20 dBm Power Level (HT20/HT40 : MCS7) Spectrum Mask (HT20) Constellation Error (EVM) RX Characteristics Maximum Input Level (PER ≤ 10%) * Normal Condition : 25℃, VDD=5V. ©2011 LGIT. All rights reserved. DOCUMENT No : REG. DATE : 2011.10.22 SPECIFICATION REV. DATE : 2011.10.22 MODEL NAME : TWFM-B005D HC40787 REV.NO : 1.1 PAGE : 11 / 16 8. Environment Tests Item Test Conditions Specifications Initial values are measured at standard test condition. Heat Load Test Leave samples in 60℃±2℃ for 500 ±5 hours, and in standard test condition for 30 minutes, then take measurements within 1 hour. pp y voltage g : standard ± 5% - Supply - Supply voltage cycle : 1.5h on, 0.5h off Initial values are measured at standard test condition. Humidity Load Test Leave samples in 40℃±5℃, 40℃±5℃ 90 ~ 95% RH for 96 ±5 hours, and in standard test condition for 30 minutes, then take measurements within 1 hour. - Supply voltage : standard + 5% - Supply voltage cycle : 1.5h on, 0.5h off Initial values are measured at standard test condition. Cold Test Leave samples in -10℃ ±2℃ for 96 ±5 hours, and in standard ambient for 1 hour with standard power Supply then take measurements within 1 hour. Take measurements in standard test condition. Temperature Shock Temp. : -10℃ ~ +80℃ Duration : 30 min Ramp-up & Ramp-down for 5 min Cycle : 100cycle. 100cycle ©2011 LGIT. All rights reserved. •TX Power : ±4dB Max • Min Input Level : ±4dB Max DOCUMENT No : REG. DATE : 2011.10.22 SPECIFICATION REV. DATE : 2011.10.22 MODEL NAME : TWFM-B005D HC40787 REV.NO : 1.1 PAGE : 12 / 16 9. Pin Description Pin No. Pin Name I/O Pin Description VDD VDD 5V USB_DN I/O USB Communication signal USB_DN USB_DP I/O USB Communication signal USB_DP GND GND WoWLAN Wake-On - Wireless LAN GND GND < TOP View Vi Note Note. 1) Recommend a Module install sequence for prevent USB device failure - Supply 5V power - Connect to data signal (USB_DP, USB_DN) 2) If remove the module, proceed in reveres sequence 3) Connector A : A1257WR0-6PS ( JWT) ©2011 LGIT. All rights reserved. DOCUMENT No : REG. DATE : 2011.10.22 SPECIFICATION REV. DATE : 2011.10.22 MODEL NAME : TWFM-B005D HC40787 REV.NO : 1.1 PAGE : 13 / 16 10. S/W The module is controlled by wl command. It is intended for those evaluating and/or testing Broadcom’s IC, describes a subset of the commands available in wl, the Broadcom ® WLAN client utility. 1) Command Syntax The syntax is as follows: wl[-h] [-d|u|x] [arguments] where -h this message and command descriptions -d output format signed integer -u output format unsigned integer -x output format hexdecimal The [h,u] option is only to print help. Other syntax specifics are as follows: • Entries within square brackets, such as [arguments], are optional. In the above example, switches within brackets, such as –h, are typed as shown. The |symbol should not be typed, it represents the word or. • Entries within angle brackets, such as , are required and indicate that a value must be inserted in place of the item contained within the angle brackets. • Entries shown outside of either square or angle brackets are to be typed as shown. 2) Command List and Version • CMDS Syntax: wl cmds Purpose: Generates a list of available commands. Parameters:None Returns: All commands available to the attached 43XX chip. • VER Syntax: wl ver Purpose: Generates a list of available commands. Parameters:None Returns: All commands available to the attached 43XX chip. • Please refer to ‘80211-TI201-R’ technical document of Broadcom to other commands. ©2011 LGIT. All rights reserved. DOCUMENT No : REG. DATE : 2011.10.22 SPECIFICATION REV. DATE : 2011.10.22 MODEL NAME : TWFM-B005D 11. Assembly Drawing ©2011 LGIT. All rights reserved. HC40787 REV.NO : 1.1 PAGE : 14 / 16
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author :EXIF Metadata provided by EXIF.toolsCreate Date : 2011:11:16 18:00:50+09:00 Modify Date : 2011:12:02 11:06:46+09:00 Has XFA : No XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2011:12:02 11:06:46+09:00 Format : application/pdf Title : Microsoft PowerPoint - Specification_TWFM-B005D.ppt [호환 모드] Creator : Producer : Acrobat Distiller 9.0.0 (Windows) Document ID : uuid:33583ffb-adf5-4dae-b1fd-44a452bae6c6 Instance ID : uuid:8f9b3fbd-518b-42a5-81ed-5b2c99a40364 Page Count : 15