LabelZone Tsc Ttp 247 345 245 Plus 343 User Manual
2017-09-18
User Manual: LabelZone Tsc Ttp-247-Ttp-345-Ttp-245-Plus-Ttp-343-Plus User Manual
Open the PDF directly: View PDF 
.
Page Count: 52
| Download | |
| Open PDF In Browser | View PDF |
TTP-245 Plus / TTP-343 Plus TTP-247 / TTP-345 THERMAL TRANSFER / DIRECT THERMAL BAR CODE PRINTER USER’S MANUAL Contents COPYRIGHT DECLARATION ....................................................................................................... 1 COMPLIANCES......................................................................................................................... 1 1. Introduction ................................................................................................................. 1 2. Getting Started ............................................................................................................ 1 2.1 Unpacking and Inspection ................................................................................... 1 2.2 Equipment Checklist ............................................................................................ 1 2.3 Printer Parts .......................................................................................................... 3 3. Setup ............................................................................................................................ 4 3.1 Setting Up the Printer ........................................................................................... 4 3.2 Loading the Ribbon .............................................................................................. 5 3.3 Loading Label Stock ............................................................................................ 7 3.4 External Label Roll Mount Installation (Option) ................................................ 9 3.5 Peel-off Module Installation (Option) ................................................................ 11 3.5.1 Loading the Paper in Peel-off Mode .......................................................... 14 3.6 Cutter Module Installation (Option) .................................................................. 16 3.6.1 Loading Label in Cutter Mode.................................................................... 19 3.7 Instructions to Top Cover Operation ................................................................ 20 3.8 Diagnostic Tool ................................................................................................... 22 3.8.1 Start the Diagnostic Tool ............................................................................ 22 3.8.2 Printer Function (Calibrate sensor, Ethernet setup, RTC setup………) 23 3.9 Setting Ethernet by Diagnostic Utility (Option) ............................................... 24 3.9.1 Using USB interface to setup Ethernet interface ..................................... 24 3.9.2 Using RS-232 interface to setup Ethernet interface ................................ 25 3.9.3 Using Ethernet interface to setup Ethernet interface .............................. 26 3.10 Install Memory Card ......................................................................................... 28 4. Power on Utilities ...................................................................................................... 30 4.1 Ribbon and Gap/Black Mark Sensor Calibration ............................................ 30 4.2 Gap/Black Mark Calibration, Self-test and Dump Mode ................................. 31 4.3 Printer Initialization ............................................................................................ 35 4.4 Set Black Mark Sensor as Media Sensor and Calibrate the Black Mark Sensor 36 4.5 Set Gap Sensor as Media Sensor and Calibrate the Gap Sensor.................. 36 4.6 Skip AUTO.BAS .................................................................................................. 36 5. Maintenance .............................................................................................................. 38 5.1 Cleaning............................................................................................................... 38 6. Troubleshooting ........................................................................................................ 40 i 6.1 LED Status .......................................................................................................... 40 6.2 Print Quality ........................................................................................................ 41 7. LED and Button Operation ....................................................................................... 43 7.1 LED....................................................................................................................... 43 8.2 Button Operation ................................................................................................ 43 Revise History ............................................................................................................... 46 ii Copyright Declaration Information in this subject to change without notice and does not represent a commitment on the part of TSC Auto ID Technology Co., Ltd.. No part of this manual may be reproduced or transmitted in any form by any means, for any purpose other than the purchaser’s personal use, without the expressed written permission of TSC Auto ID Technology Co., Ltd.. Compliances CE Class B: EN55022: 1998+A1: 2000+A2: 2003 EN55024: 1998+A1: 2001+A2: 2003 IEC 61000-4 Series EN61000-3-2: 2006 & EN61000-3-3: 1995+A1: 2001 FCC Part 15, Class B UL, CUL C-Tick: CFR 47, Part 15/CISPR 22 3rd Edition: 1997, Class B ANSI C63.4: 2003 Canadian ICES-003 TÜ V/Safety: EN60950: 2000 Wichtige Sicherheits-Hinweise 1. Bitte lesen Sie diese Hinweis sorgfältig durch. 2. Heben Sie diese Anleitung fűr den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromentz zu trennen. Verwenden Sie keine Flüssig-oder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur Reinigung. 4. Die Netzanschluß -Steckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuchtigkeit zu schűtzen. 6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen könnte Beschädigungen hervorrufen. 7. Beachten Sie beim Anschluß ans Stromnetz die Anschluß werte. 8. Dieses Gerät kann bis zu einer Auß entemperatur von maximal 40℃ betrieben werden. 1 CAUTION 1. HAZARDOUS MOVING PARTS IN CUTTER MODULE. KEEP FINGER AND OTHER BODY PARTS AWAY. 2. THE MAIN BOARD INCLUDES REAL TIME CLOCK FEATURE HAS LITHIUM BATTERY CR2032 INSTALLED. RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. 3. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER INSTRUCTIONS. B 급기기 (가정용 정보통신기기) 이 기기는 가정용으로 전자파 적합등록을 한 기기로서 주거지역에서는 물론 모든 지역에서 사용할 수 있습니다. 2 1. Introduction Thank you for purchasing the TSC TTP-245/343 Plus series, TTP-247/345 series Thermal Transfer and Direct Thermal Bar Code Printers. Although the printer takes only a small amount of space, it delivers reliable, superior performance. This printer provides both thermal transfer and direct thermal printing at user selectable speed of: 2.0, 3.0, 4.0 or 5.0 ips, for TTP-245/345 series; 2.0 or 3.0 ips for TTP-343 series, .2.0, 3.0, 4.0, 5.0, 6.0 or 7.0 ips It accepts roll feed, die-cut, and fan-fold labels for both thermal transfer and direct thermal printing. All common bar codes formats are available. Fonts and bar codes can be printed in 4 directions, 8 different alphanumeric bitmap fonts and a build-in true type font capability. You will enjoy high throughput for printing labels with this printer. 2. Getting Started 2.1 Unpacking and Inspection This printer has been specially packaged to withstand damage during shipping. Please carefully inspect the packaging and printer upon receiving the bar code printer. Please retain the packaging materials in case you need to reship the printer. 2.2 Equipment Checklist Printer BarTender UltraLite CD disk Quick start guide USB port cable External universal switching power supply Power Cord Label Spindle, fixing tab x2, 1.5” core adapter x2 Ribbon spindle x2 Ribbon rewind spindle paper core If any parts are missing, please contact the Customer Service Department of your purchased reseller or distributor. Dealer option Peel off module assembly Support paper: Art paper (Plain paper) Support label length: 1”~6” Support speed: 2~3 ips Guillotine cutter Full cut: Paper thickness: 0.06~ 0.19mm, 500,000 cuts Paper thickness: 0.19mm 200,000 cuts Partial cut: Paper thickness: 0.06~0.12mm, 500,000 cuts Note: Except for the linerless cutter, all regular/heavy duty/care label cutters DO NOT cut on media with glue. Main board integrated with internal Ethernet Internal Ethernet print server module User option KP-200 KU-007 plus External Ethernet print server External wireless (802.11b/g) print server External roll mount, media OD. 214 mm (8.4”) with 3” core label spindle Contact CCD contact scanner Long range linear image bar code scanner 2 2.3 Printer Parts Clear Window Ribbon Access Cover LED Indicator Feed Button Printer Top Cover Top Cover Open Lever Fig. 1 Top front view 1. USB Interface 2. Centronics Interface 3. RS-232C DB-9 Interface 4. Power Jack 5. Power Switch 6 6. 1 2 3 4 Rear Paper Guide 5 Fig. 2 Rear view Note: The interface picture here is for reference only. Please refer to the product specification for the interfaces availability. 3 3. Setup 3.1 Setting Up the Printer 1. Place the printer on a flat, secure surface. 2. Make sure the power switch is off. 3. Connect the printer to the computer with the Centronics or USB cable. 4. Plug the power cord into the power supply connector at the rear of the printer, and then plug the power cord into a properly grounded receptacle. Plug USB Power Switch Power Cable Centronics RS-232C Power Supply Fig. 3 Attach power supply to printer Note: Please switch OFF printer power switch prior to plug in the power cord to printer power jack. 4 3.2 Loading the Ribbon The printer will detect if the ribbon is installed after turning on power on and it will set printing mode to thermal transfer or direct thermal printing mode automatically. If printer does not detect the ribbon, the ribbon take up motor will be turned off. Make sure the printer top cover is engaged properly at both sides prior to powering up the printer. Please follow the steps below to install the ribbon into printer. 1. 2. 3. 4. 5. 6. 7. 8. Push down on the ribbon access window to unlatch and open the cover. Place a paper core onto the ribbon rewind spindle. Mount the ribbon rewind paper core on the front hubs. Install a ribbon on the ribbon supply spindle. Mount the ribbon supply spindle on the rear hubs. Thread the ribbon leading tape downward pass the print head. Attach the ribbon leader to the ribbon rewind paper core. Rotate the ribbon rewind paper core until the ribbon leader is thoroughly, firmly encompassed by the black section of the ribbon. 9. Close the ribbon access window. Note: Please refer to videos on TSC YouTube or driver CD. Paper Core Ribbon Access Cover Ribbon Spindle Back Hub Front Hub Fig. 4 Ribbon installation (I) 5 Ribbon supply spindle Ribbon Lead Tape Rear Hub Ribbon Rewind Spindle with Paper Core Fig. 5 Ribbon installation (II) 6 3.3 Loading Label Stock 1. Insert a 1” label spindle into a paper roll ( * If your paper core is 1 inch, remove the 1.5” core adapter from the fixed tab. If label width is 4 inch wide, two fixing tabs are not required. ). 1.5” Core Paper Roll Adapter* Fixed Tab Printing Side Face Up 1” Label Spindle Fig. 6 Label roll installation (I) 2. Open the printer’s top cover by releasing the green top cover open levers located on each side of the printer and lifting the top cover. A top cover support at the rear of the printer will hold the printer top cover open. Lower Cover 3. 4. 5. 6. Fig. 7 Pull the lever to open the cover Place a roll of paper onto the center of the paper roll mount. Feed the paper, printing side face up, through the Teflon bar and the paper guide and pass over the platen. Adjust the green center-biased paper guides to slightly touch the edges of the label backing. To close the printer top cover, lift the cover to the ultimate open angle then use 7 both hands to close the cover gently. Close the printer top cover slowly and make sure the cover latches securely. Note: Make sure hands are not placed between printer top cover and lower cover when close the top cover. 1. Do not free fall the top cover. 2. Failure to securely close and lock the cover will result in poor print quality. 3. Please refer to videos on TSC YouTube or driver CD. Printer Top Cover Top Cover Support Paper Roll Mount Teflon Bar Paper Guide Top Cover Open Lever Fig. 8 Label installation (II) 8 3.4 External Label Roll Mount Installation (Option) 1. Attach an external paper roll mount on the bottom of the printer. Fig. 9 Attach the external roll mount to the printer 4. Open the printer top cover by releasing the top cover open levers. The top cover support will hold the printer top cover. Install a roll of paper on the external paper roll mount. 5. Feed the paper to the external paper feed opening through the rear paper guide. External Paper Roll Mount External Paper Feed Opening Fig. 10 External roll mount label installation (I) 4. Feed the paper, printing side face up, through the paper guide and pass over the platen. 5. Adjust the paper guides to fit the paper width. 9 6. Close the printer top cover by lifting the top cover to the maximum opening angle then push down the top cover gently. Rear Paper Guide Top Cover Support Paper Guide Platen Fig. 11 External roll mount label installation (II) 10 3.5 Peel-off Module Installation (Option) 1. Open the top cover and remove the front panel from the printer. Front Panel Fig. 12 Remove the front panel 2. Open the top cover and hold it and push down and push backward the top cover support then push backward the top cover. 3. Use a screwdriver to screw off 6 screws on the lower inner cover. Top Cover Top Cover Support Screws Flute Lower Inner Cover Screws Lower Cover Fig. 13 Remove 6 screws from lower inner cover 4. Upside down the printer. Remove two screws at the hinge and remove one screw at memory card cover. 11 5. Hold the lower cover to lift up the top cover open levers to separate the lower inner cover and the lower cover. 6. Arrange the cable through the bezel. Connect the peel-off panel cable to the 5-pin socket on printer PCB. PCB 5-pin Socket Peel-off panel Cable Peel-off panel Fig. 14 Connect peel-off sensor cable to main board Tenon Bezel Mortise Fig. 15 Peel-off sensor cable installation 7. Insert the peel-off tenons into the lower inner cover mortises until tenons snap 12 into places. Lower Inner Cover Roller Lower Cover Tenon Mortise Fig. 16 Peel-off panel installation (I) 8. Arrange the lower inner cover back to the lower cover. Peel-off panel Roller Fig. 17 Peel-off panel installation (II) 9. Lift up the peel-off panel to the lower cover to close it. 10. Use a screwdriver to screw down whole screws on the lower inner cover and the lower cover. 11. Close the top cover by arranging the top cover support back to the flute and push it forward then close the top cover slowly. 13 3.5.1 Loading the Paper in Peel-off Mode 1. Insert a 1” label spindle into a paper roll. 2. Open the printer top cover by pulling the top cover open levers. The top cover support will hold the printer top cover. Peel-off panel Backing paper Top Cover Open Lever Opening Fig. 18 Open the top cover 3. Install the paper roll on the paper roll mount. 4. Open the peel-off panel by pulling it out. Peel-off panel Fig. 19 Open the peel-off panel 5. Feed the paper, printing side facing up, through the paper guide and pass over the platen. 6. Lead the paper through the backing paper opening, beneath the roller, and tear off one piece of the label. 14 7. Adjust the paper guide by removing left or right to fit the paper width. Top Cover Top Cover Support Roller Peel-off panel Fig. 20 Lead the paper through the backing paper opening, beneath the roller 8. Push the peel-off panel back to the printer. 9. Close the top cover by lifting up the top cover support and close the top cover slowly. Note: 1. Pull the label outward tightly after closing the top cover. 2. Both thermal paper and plain paper apply for peel-off function but neither PVC nor vynle work at peel-off function. 3. Please refer to videos on TSC YouTube or driver CD. Fig. 21 Complete label installation for peel-off mode 15 3.6 Cutter Module Installation (Option) 1. Pull the top cover open levers to open the top cover. 2. Remove the front panel from the lower cover. Lower Cover Fig. 22 Pull the lever to open the cover 3. Open the top cover and hold it and push down and push backward the top cover support then push backward the top cover. 4. Use a screwdriver to screw off 6 screws on the lower inner cover. Top Cover Top Cover Support Screws Flute Front Panel Screws Lower Inner Cover Lower Cover Fig. 23 Remove 6 screws from lower inner cover 16 5. Place the printer upside down and unscrew the two screws of the hinge holder on the lower cover. 6. Unscrew the screw of the memory card cover and remove the memory card cover. Plug in the cutter driver IC at U14(TTP-245/343) / U30(TTP-245 Plus/343 Plus/247/345) socket on the main board. 7. Use both thumbs to hold the lower cover and index fingers to lift up the top cover open levers to separate the lower inner cover and the lower cover. 8. Arrange the cable through the bezel. Connect the cutter module cable to the 4-pin socket on printer PCB. PCB 4-pin Socket Cutter Cable Cutter Fig. 24 Cutter module installation Lower Inner Cover Cutter Cable Lower Cover Fig. 25 Cutter module cable arrangement 9. Arrange the lower inner cover back to the lower cover. 10. Install the cutter into the niches of the printer. 17 Bezel Cutter Niche Fig. 26 Cutter module installation 11. Use a screwdriver to screw whole screws on the lower inner cover and the lower cover. 12. Close the top cover by arranging the top cover support back to the flute and push it forward then close the top cover slowly. 18 3.6.1 Loading Label in Cutter Mode 1. 2. 3. 4. Insert a 1” label spindle into a paper roll. Open the printer top. Install a paper roll on the paper roll mount. Feed the paper, printing side face up, through the paper guide and pass over the platen. 5. Lead the paper through the cutter paper opening. 6. Adjust the paper guide by removing left or right to fit the paper width. Top Cover Top Cover Support Paper Guide Platen Cutter Fig. 27 Label installation in cutter mode 7. Close the top cover by lifting up the top cover support and close the top cover slowly. Fig. 28 Complete label installation in cutter mode 19 3.7 Instructions to Top Cover Operation Please take care when opening or closing the printer’s top cover by carefully following these instructions. To Open: 1. When facing the front of the printer pull the cover release levers on both sides of printer towards you. 2. Lift up the top gradually. There are two stop positions for the top cover. Position 1 and 2 are indicated on the label below. Note: To hold the cover open at position 1, you must lift the cover higher than the stopping point at position 1 and gently lower the cover to stop position 1. DO NOT free fall the top cover! 3. Fully open the top cover and gently lower it to stop position 2. Fig. 1 Top cover support is fixed at position 2 4. To close the cover, lift up the top cover to the ultimate angle then close the top cover gently and it will be kept at a stop position between 1 and 2 for a while. Use both hands to gently push down the top cover to close it and make sure the cover is latched on both sides. Note: DO NOT place your hands between top cover and lower cover while close the top cover! 20 Fig. 2 Top cover is fully open and ready to close Fig. 3 Use both hands to close the top cover 5. Do not force the cover! If you are not sure if top cover is fixed at stop position, please do not push top cover to close it or the top cover will be damaged. Please open the top cover to the ultimate angle to close the top cover again. Use both hands to push top cover to close it. Note: Please refer to videos on TSC YouTube or driver CD. 21 3.8 Diagnostic Tool The Diagnostic Utility is a toolbox that allows users to explore the printer’s settings and status; change printer settings; download graphics, fonts, and firmware; create printer bitmap fonts; and to send additional commands to the printer. Using this convenient tool, you can explore the printer status and settings and troubleshoot the printer. Note: This utility works with printer firmware V6.00 and later versions. 3.8.1 Start the Diagnostic Tool 1. Double click on the Diagnostic tool icon to start the software. 2. There are four features (Printer Configuration, File Manager, Bitmap Font Manager, Command Tool) included in the Diagnostic utility. Features tab Interface Printer functions Printer setup Printer Status 22 3.8.2 Printer Function (Calibrate sensor, Ethernet setup, RTC setup………) 1. Select the PC interface connected with bar code printer. 2. Click the “Function” button to setting. 3. The detail functions in the Printer Function Group are listed as below. Function Calibrate Sensor Ethernet Setup Description Calibrate the sensor specified in the Printer Setup group media sensor field Setup the IP address, subnet mask, gateway for the on board Ethernet (Please refer to next section) RTC Time Synchronize printer Real Time Clock with PC Print Test Page Print a test page Reset Printer Reboot printer Factory Default Initialize the printer and restore the settings to factory default. Dump Text To activate the printer dump mode. Ignore AUTO.BAS Ignore the downloaded AUTO.BAS program Configuration Page Print printer configuration Note: For more information about Diagnostic Tool, please refer to the diagnostic utility quick start guide in the CD disk \ Utilities directory. 23 3.9 Setting Ethernet by Diagnostic Utility (Option) The Diagnostic Utility is enclosed in the CD disk \Utilities directory. Users can use Diagnostic Tool to setup the Ethernet by RS-232, USB and Ethernet interfaces. The following contents will instruct users how to configure the Ethernet by these three interfaces. 3.9.1 Using USB interface to setup Ethernet interface 1. Connect the USB cable between the computer and the printer. 2. Turn on the printer power. 3. Start the Diagnostic Utility by double clicking on the icon. Note: This utility works with printer firmware V6.00 and later versions. 4. The Diagnostic Utility default interface setting is USB interface. If USB interface is connected with printer, no other settings need to be changed in the interface field. 5. Click on the “Ethernet Setup” button from “Printer Function” group in Printer Configuration tab to setup the IP address, subnet mask and gateway for the on board Ethernet. 24 3.9.2 Using RS-232 interface to setup Ethernet interface 1. Connect the computer and the printer with a RS-232 cable. 2. Turn on the printer power. 3. Start the Diagnostic Utility by double clicks on the icon. Note: This utility works with printer firmware V6.00 and later versions. 4. Select “COM” as interface then click on the “Setup” button to setup the serial port baud rate, parity check, data bits, stop bit and flow control parameters. 5. Click on the “Ethernet Setup” button from printer function of Printer Configuration tab to setup the IP address, subnet mask and the gateway for the on board Ethernet. 25 3.9.3 Using Ethernet interface to setup Ethernet interface 1. Connect the computer and the printer to the LAN. 2. Turn on the printer power. 3. Start the Diagnostic Utility by double clicks on the icon. Note: This utility works with printer firmware V6.00 and later versions. 4. Select “Ethernet” as the interface then click on the “Setup” button to setup the IP address, subnet mask and gateway for the on board Ethernet. 5. Click the “Discover Device” button to explore the printers that exist on the network. 6. Select the printer in the left side of listed printers, the correspondent IP address will be shown in the right side “IP address/Printer Name” field. 7. Click “Change IP Address” to configure the IP address obtained by DHCP or static. 26 The default IP address is obtained by DHCP. To change the setting to static IP address, click “Static IP” radio button then enter the IP address, subnet mask and gateway. Click “Set IP” to take effect the settings. Users can also change the “Printer Name” by another model name in this fields then click “Set Printer Name” to take effect this change. Note: After clicking the “Set Printer Name” or “Set IP” button, printer will reset to take effect the settings. 8. Click “Exit” button to exit the Ethernet interface setup and go back to Diagnostic Tool main screen. Factory Default button This function will reset the IP, subnet mask, gateway parameters obtained by DHCP and reset the printer name. Web setup button Except to use the Diagnostic Utility to setup the printer, you can also explore and configure the printer settings and status or update the firmware with the IE or Firefox web browser. This feature provides a user friendly setup interface and the capability to manage the printer remotely over a network. 27 3.10 Install Memory Card 1. Turn the printer upside down. 2. Remove the screw that fixes the memory card cover. Screw Memory Card Cover 3. Plug in the memory card on main board. TTP-245/343 Model (Option) 4. TTP-245 Plus/343 Plus/247/345 Model (SD Card) Close the memory card cover. * Recommended SD card specification. SD card spec SD card capacity Approved SD card manufacturer V1.0, V1.1 128 MB SanDisk, Transcend V1.0, V1.1 256 MB SanDisk, Transcend, Panasonic V1.0, V1.1 512 MB SanDisk, Transcend, Panasonic V1.0, V1.1 1 GB SanDisk, Transcend, Panasonic V2.0 SDHC CLASS 4 4 GB V2.0 SDHC CLASS 6 4 GB SanDisk, Transcend, Panasonic V1.0, V1.1 microSD 128 MB Transcend, Panasonic V1.0, V1.1 microSD 256 MB Transcend, Panasonic 28 V1.0, V1.1 microSD 512 MB Panasonic V1.0, V1.1 microSD 1 GB Transcend, Panasonic V2.0 SDHC CLASS 4 microSD 4 GB Panasonic V2.0 SDHC CLASS 6 microSD 4 GB Transcend V1.0, V1.1 miniSD 128 MB Transcend, Panasonic V1.0, V1.1 miniSD 256 MB Transcend, Panasonic V1.0, V1.1 miniSD 512 MB Transcend, Panasonic V1.0, V1.1 miniSD 1 GB Transcend, Panasonic V2.0 SDHC CLASS 4 miniSD 4 GB Transcend V2.0 SDHC CLASS 6 miniSD 4 GB - The DOS FAT file system is supported for the SD card. - Folders/files stored in the SD card should be in the 8.3 filename format - The miniSD/microSD card to SD card slot adapter is required. 29 4. Power on Utilities There are six power-on utilities to set up and test printer hardware. These utilities are activated by pressing FEED button and by turning on the printer power simultaneously. The utilities are listed as below: 1. Ribbon sensor calibration and Gap or black mark sensor calibration 2. Gap/black mark sensor calibration；Self-test and dump mode 3. 4. 5. 6. Printer initialization Set black mark sensor as media sensor and calibrate the black mark sensor Set gap sensor as media sensor and calibrate the gap sensor Skip AUTO.BAS Note: Please refer to videos on TSC YouTube or driver CD. 4.1 Ribbon and Gap/Black Mark Sensor Calibration Gap/black mark sensor sensitivity should be calibrated at the following conditions: 1. A brand new printer 2. Change label stock. 3. Printer initialization. Please follow the steps below to calibrate the ribbon and gap/black mark sensor. 1. Turn off the power switch. 2. Hold on the button then turn on the power switch. 3 Release the button when LED becomes red and blinking. (Any red will do during the 5 blinks). It will calibrate the ribbon sensor and gap/black mark sensor sensitivity. The LED color will be changed as following order： Amber red (5 blinks) amber (5 blinks) green (5 blinks) green/amber (5 blinks) red/amber (5 blinks) solid green Note: Please select gap or black mark sensor by sending GAP or BLINE command to printer prior to calibrate the sensor. For more information about GAP and BLINE command, please refer to TSPL2 programming manual. 30 4.2 Gap/Black Mark Calibration, Self-test and Dump Mode While calibrate the gap/black mark sensor, printer will measure the label length, print the internal configuration (self-test) on label and then enter the dump mode. To calibrate gap or black mark sensor, depends on the sensor setting in the last print job. Please follow the steps below to calibrate the sensor. 1.Turn off the power switch. 2. Hold on the button then turn on the power switch. 3. Release the button when LED becomes amber and blinking. (Any amber will do during the 5 blinks). The LED color will be changed as following order. Amber red (5 blinks) amber (5 blinks) green (5 blinks) green/amber (5 blinks) red/amber (5 blinks) solid green 2. It calibrates the sensor and measures the label length and prints internal settings then enter the dump mode. Note: Please select gap or black mark sensor by Diagnostic tool or by GAP or BLINE command prior to calibrate the sensor. For more information about GAP and BLINE command, please refer to TSPL2 programming manual. 31 Self-test Printer will print the printer configuration after gap/black mark sensor calibration. Self-test printout can be used to check if there is any dot damage on the heater element, printer configurations and available memory space. Self-test printout Print head check pattern Model name and F/W version Printed mileage (meter) Firmware checksum Serial port configuration Code page Country code Print speed (inch/sec) Print darkness Label size (inch) Gap distance (inch) Gap/black mark sensor sensitivity Numbers of download files Total & available memory space Self-test printout (with printer firmware V7.0 and later version) Model name F/W version Firmware checksum Printer S/N TSC configuration file System date System time Printed mileage (meter) Cutting counter 32 Print speed (inch/sec) Print darkness Label size (inch) Gap distance (inch) Gap/black mark sensor intension Code page Country code ZPL setting information Print darkness Print speed (inch/sec) Label size Control prefix Format prefix Delimiter prefix Printer power up motion Printer head close motion Note: ® ZPL is emulating for Zebra language. RS232 serial port configuration Numbers of download files Total & available memory space Print head check pattern 33 Dump mode Printer will enter dump mode after printing printer configuration. In the dump mode, all characters will be printed in 2 columns as following. The left side characters are received from your system and right side data are the corresponding hexadecimal value of the characters. It allows users or engineers to verify and debug the program. ASCII Data Hex decimal data related to left column of ASCII data Fig. 30 Dump mode printout Note: Turn off / on the power to resume printer for normal printing. 34 4.3 Printer Initialization Printer initialization is used to clear DRAM and restore printer settings to defaults. The only one exception is ribbon sensitivity, which will note be restored to default. Printer initialization is activated by the following procedures. 1. Turn off the power switch. 2. Hold on the button then turn on the power switch. 3. Release the button when LED turns green after 5 amber blinks. (Any green will do during the 5 blinks). The LED color will be changed as following: Amber red (5 blinks) amber (5 blinks) green (5 blinks) green/amber (5 blinks) red/amber (5 blinks) solid green Printer configuration will be restore to defaults as below after initialization. Parameter Default setting Speed 203DPI :127 mm/sec (5 ips) 300DPI: 76 mm/sec (3 ips) Density 8 Label Width 4” (101.6 mm) Label Height 4” (101.6 mm) Sensor Type Gap sensor Gap Setting 0.12” (3.0 mm) Print Direction 0 Reference Point 0,0 (upper left corner) Offset 0 Tear Mode On Peel off Mode Off Cutter Mode Off Serial Port Settings 9600 bps, none parity, 8 data bits, 1 stop bit Code Page 850 Country Code 001 Clear Flash Memory No IP Address DHCP Note： Always do gap/black mark sensor calibration after printer initialization. 35 4.4 Set Black Mark Sensor as Media Sensor and Calibrate the Black Mark Sensor Please follow the steps as below. 1. Turn off the power switch. 2. Hold on the button then turn on the power switch. 3. Release the button when LED turns green/amber after 5 green blinks. (Any green/amber will do during the 5 blinks). The LED color will be changed as following: Amber red (5 blinks) amber (5 blinks) green (5 blinks) green/amber (5 blinks) red/amber (5 blinks) solid green 4.5 Set Gap Sensor as Media Sensor and Calibrate the Gap Sensor Please follow the steps as below. 1. Turn off the power switch. 2. Hold on the button then turn on the power switch. 3. Release the button when LED turns red/amber after 5 green/amber blinks. (Any red/amber will do during the 5 blinks). The LED color will be changed as following: Amber red (5 blinks) amber (5 blinks) green (5 blinks) green/amber (5 blinks) red/amber (5 blinks) solid green 4.6 Skip AUTO.BAS TSPL2 programming language allows user to download an auto execution file to flash memory. Printer will run the AUTO.BAS program immediately when turning on printer power. The AUTO.BAS program can be interrupted without running the program by the power-on utility. Please follow the procedures below to skip an AUTO.BAS program. 36 1. Turn off printer power. 2. Press the FEED button and then turn on power. 3. Release the FEED button when LED becomes solid green. The LED color will be changed as following: Amber red (5 blinks) amber (5 blinks) green (5 blinks) green/amber (5 blinks) red/amber (5 blinks) solid green 4. Printer will be interrupted to run the AUTO.BAS program. 37 5. Maintenance 5.1 Cleaning This session presents the clean tools and methods to maintain your printer. 3. Please use one of following material to clean the printer. Cotton swab (Head cleaner pen) Lint-free cloth Vacuum / Blower brush 100% ethanol 4. The cleaning process is described as following Printer Part Method Interval 1. Always turn off the printer Clean the print head when before cleaning the print head. changing a new label roll 2. Allow the print head to cool for a minimum of one minute. 3. Use a cotton swab (Head cleaner pen) and 100% ethanol to clean the print head surface. Print Head 1. Turn the power off. 2. Rotate the platen roller and wipe it thoroughly with 100% Platen Roller ethanol and a cotton swab, or lint-free cloth. Clean the platen roller when changing a new label roll Tear Bar/Peel Use the lint-free cloth with 100% As needed ethanol to wipe it. Bar Sensor Compressed air or vacuum Monthly Exterior Wipe it with water-dampened As needed 38 cloth Interior Brush or vacuum As needed Note: Do not touch printer head by hand. If you touch it careless, please use ethanol to clean it. Please use 100% Ethenol. DO NOT use medical alcohol, which may damage the printer head. Regularly clean the print head and supply sensors once change a new ribbon to keep printer performance and extend printer life. 39 6. Troubleshooting The following guide lists the most common problems that may be encountered when operating this bar code printer. If the printer still does not function after all suggested solutions have been invoked, please contact the Customer Service Department of your purchased reseller or distributor for assistance. 6.1 LED Status This section lists the common problems that according to the LED status and other problems you may encounter when operating the printer. Also, it provides solutions. LED Printer Possible Status / Color Status Cause OFF No response No power Recovery Procedure * Turn on the power switch. * Check if the green LED is lit on power supply. If it is not lit on, power supply is broken. * Check both power connections from the power cord to the power supply and from the power supply to the printer power jack if they are connected securely. Solid Green ON The printer is * No action necessary. ready to use Green with Pause blinking Red with blinking Error The printer is * Press the FEED button to resume for paused printing. The out of label or 1. Out of label or ribbon ribbon or the * Load a roll of label and follow the printer setting is instructions in loading the media then not correct press the FEED button to resume for printing. * Load a roll of ribbon and follow the instructions in loading the ribbon then press the FEED button to resume for printing. 2. Printer setting is not correct * Initialize the printer by instructions in “Power on Utility” or “Diagnostic Tool”. 40 Note: Printer status can be easily shown on the Diagnostic Tool. For more information about the Diagnostic Tool, please refer to the instruction in the software CD disk. 6.2 Print Quality Problem Possible Cause Check if interface cable is well Recovery Procedure Re-connect cable to interface. connected to the interface connector. The serial port cable pin configuration is not pin to pin connected. Not Printing Please replace the cable with pin to pin connected. The serial port setting is not Please reset the serial port consistent between host and setting. printer. The port specified in the Windows Select the correct printer port in driver is not correct. the driver. The Ethernet IP, subnet mask, gateway is not configured properly. No print on the label Continuous feeding labels Configure the IP, subnet mask and gateway. Label or ribbon loaded not Follow the instructions in loading correctly. the media or loading the ribbon. Ribbon run out. Loading the ribbon. The printer setting may go wrong. Please do the initialization and gap/black mark calibration. Gap/black mark sensor sensitivity Calibrate the gap/black mark sensor. is not set properly (sensor sensitivity is not enough) Paper Jam Make sure label size is set properly. Labels may be stuck inside the Set label size exactly as installed paper in the labeling software or program. Remove the stuck label. printer mechanism near the sensor area. Poor Print Quality Top cover is not closed properly. Close the top cover completely and make sure the right side and left side levers are latched properly 41 Check if supply is loaded correctly. Reload the supply. Change the ribbon or label combination. Ribbon and media are incompatible. Check if dust or adhesives are Clean the print head. accumulated on the print head. Check if print density is set Adjust the print density and print speed. properly. Check print head test pattern if head element is damaged. 42 Run printer self-test and check the print head test pattern if there is dot missing in the pattern. 7. LED and Button Operation 7.1 LED LED Color Description Green/ Solid This illuminates that the power is on and the device is ready to use. Green/ Flash This illuminates that the system is downloading data from PC to memory and the printer is paused. Amber This illuminates that the system is clearing data from printer. Red / Solid This illuminates printer head open, cutter error. Red / Flash This illuminates a printing error, such as head open, paper empty, paper jam, ribbon empty, or memory error etc. 8.2 Button Operation Feed Press the button when the LED is green. It feeds the label to the beginning of the next label. Pause Press the feed button during printing The printing job is suspended. Ribbon Sensor and 1. Turn off the power switch. Gap/Black Mark 2. Hold on the button then turn on the power switch. Sensor Calibration 3 Release the button when LED becomes red and blinking. (Any red will do during the 5 blinks). It will calibrate the ribbon sensor and gap/black mark sensor sensitivity. The LED color will be changed as following order： Amber red (5 blinks) amber (5 blinks) green (5 blinks) green/amber (5 blinks) red/amber (5 blinks) solid green Note: Please select gap or black mark sensor by GAP or BLINE command prior to calibrate the sensor. For more information about GAP and BLINE command, please refer to TSPL2 programming manual. 43 Gap/Black Mark 1.Turn off the power switch. Sensor Calibratio, 2. Hold on the button then turn on the power switch. Label Length 3. Release the button when LED becomes amber and blinking. (Any amber will do during the 5 blinks). Measurement, The LED color will be changed as following order. Self Test and enter Dump Mode Amber red (5 blinks) amber (5 blinks) green (5 blinks) green/amber (5 blinks) red/amber (5 blinks) solid green It calibrates the sensor and measures the label length and prints internal settings then enter the dump mode. Note: Please select gap or black mark sensor by GAP or BLINE command prior to calibrate the sensor. For more information about GAP and BLINE command, please refer to TSPL2 programming manual. Printer Initialization 1. Turn off the power switch. 2. Hold on the button then turn on the power switch. 3. Release the button when LED turns green after 5 amber blinks. (Any green will do during the 5 blinks). The LED color will be changed as following: Amber red (5 blinks) amber (5 blinks) green (5 blinks) green/amber (5 blinks) red/amber (5 blinks) solid green Note: Always do gap/black mark sensor calibration after printer initialization. Set Black Mark 1. Turn off the power switch. Sensor as Media 2. Hold on the button then turn on the power switch. Sensor and 3. Release the button when LED turns green/amber after 5 Calibrate the Black green blinks. (Any green/amber will do during the 5 blinks). The LED color will be changed as following: Mark Sensor Amber red (5 blinks) amber (5 blinks) green (5 blinks) green/amber (5 blinks) red/amber (5 blinks) solid green 44 Set Gap Sensor as 1. Turn off the power switch. Media Sensor and 2. Hold on the button then turn on the power switch. Calibrate the Gap 3. Release the button when LED turns red/amber after 5 green/amber blinks. (Any red/amber will do during the 5 Sensor blinks). The LED color will be changed as following: Amber red (5 blinks) amber (5 blinks) green (5 blinks) green/amber (5 blinks) red/amber (5 blinks) solid green Skip AUTO.BAS 1. Turn off printer power. 2. Press the FEED button and then turn on power. 3. Release the FEED button when LED becomes solid green. The LED color will be changed as following: Amber red (5 blinks) amber (5 blinks) green (5 blinks) green/amber (5 blinks) red/amber (5 blinks) solid green 4. Printer will be interrupted to run the AUTO.BAS program. 45 Revise History Date 2008/2/29 2008/3/6 2008/3/7 Content *Add section 3.8: Diagnostic Tool Editor Camille *Add the IP Address default setting *Revise section 2.2 Camille *Add section 3.9: Install memory card *Revise the printer default setting Camille *Revise section 3.6, 4.2 and 5.1 2008/3/10 Revise the section 6 Camille 2009/3/11 Revise section 3.9 (Recommended SD card specification) Camille 2009/6/16 *Add TTP-247/345 model name Camille *Revise section 4.2 *Add caution to compliances section 2009/10/14 *Revise section 3.8 Camille *Add section 3.9 2010/11/23 * Revise compliances section Camille * Revise section 2.3 and 3.1 2011/1/25 Modify TSC address Camille 2013/4/2 Modify section 2.2(cutter spec) and 4.2(V7.0 F/W self test) Camille Add TSC YouTube web address 2014/11/11 Modify section 2.2 (Add peel-off module spec) 46 Camille TSC Auto ID Technology Co., Ltd. Corporate Headquarters 9F., No.95, Minquan Rd., Xindian Dist., New Taipei City 23141, Taiwan (R.O.C.) TEL: +886-2-2218-6789 FAX: +886-2-2218-5678 Web site: www.tscprinters.com E-mail: printer_sales@tscprinters.com tech_support@tscprinters.com 47 Li Ze Plant No.35, Sec. 2, Ligong 1st Rd., Wujie Township, Yilan County 26841, Taiwan (R.O.C.) TEL: +886-3-990-6677 FAX: +886-3-990-5577
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 52 Language : zh-TW Producer : Microsoft® Word 2010 Creator : Microsoft® Word 2010 Create Date : 2015:10:15 14:50:26+08:00 Modify Date : 2015:10:15 14:50:26+08:00EXIF Metadata provided by EXIF.tools