Laird Connectivity RATESAVER Wireless Electric Meter Monitor User Manual Manual

LS Research, LLC Wireless Electric Meter Monitor Manual

UserManual.wiki >

Laird Connectivity >

RATESAVER User Manual

Manual

LS RESEARCH WIRELESS PRODUCT DEVELOPMENT Rate$aver IHD 3 | Page Rate$aver Datasheet (rev. 1.0) LSR -DS 6) Supported Zigbee Cluster attributes and commands: CLUSTER Attributes (provided by RateSaver if a server cluster, required from ESP if a client cluster) Commands Accepted Commands Generated Basic Server ZCL version Application Version Stack Version HW Version Manufacturers Name Model Identifier Date Code Power Source Reset to Factory Defaults Identify Server Identify Time Identify Identify Query Identify Query Response Key Establishment Client Key Establishment Server Time Client Time Time Status Local Time Simple Meter Client Current Summation Delivered Current Tier 1 Summation Del Current Tier 2 Summation Del Current Tier 3 Summation Del Current Tier 4 Summation Del Current Tier 5 Summation Del Current Tier 6 Summation Del Summation Formatting Instantaneous Demand Unit of Measure Metering Device Type Status (Service Disconnect, Leak detect, Power Qual, Power Fail, Tamper Detect, Low Battery, Check Meter) Others TBD Price Client Publish Price Get Current Price Get Scheduled Prices Message Client Display Message Cancel Message Get Last Message Message Confirmation Manufacturer Specific Client tbd • Mandatory features o Join network, pair devices (ZDP bind and unbind), end device announce o Factory defaults restore

LS RESEARCH WIRELESS PRODUCT DEVELOPMENT Rate$aver IHD 4 | Page Rate$aver Datasheet (rev. 1.0) LSR -DS o Enable Identify Mode by user o Service Discovery (Match descriptor request) 7) Enclosure • Dimensions o 100mm x 64mm x 26mm • ABS Plastic • Non-glare Lens • Integrated Magnet for mounting • Front Panel Label: customizable Mylar graphical overlay 8) Power supply • Power Source o 2 AA alkaline batteries o USB connector power • External Connector (for firmware upgrade) o USB Mini-B Receptacle • Battery Life: 1 year with 60 second update interval • Reverse Battery Protection 9) Test and Programming Interface • Firmware Updates: UART interface via mini-B USB connector. External adapter required to convert USB/RS232 to UART level signals (provided by LSR). • Test & Debug: via JTAG Interface with access points in battery compartment. Supports both DIP and ZIF connector interface cables (provided by LSR). 10) Screens • Screens included as needed for particular customers. Examples include: o Current tier, current tier rate, total consumption, total monthly bill, standard header o o o Tier breakdown screen: for each tier –horizontal bar graphs or numeric table

LS RESEARCH WIRELESS PRODUCT DEVELOPMENT Rate$aver IHD 5 | Page Rate$aver Datasheet (rev. 1.0) LSR -DS   o o User Messaging Screen / Alarm Display – inverted colors-.  o Inst power screen – numeric kWatts and bar  o User Setup and Initialization  Network ID and Channel  Join Network button  Celsius/Fahrenheit  Time Zone o Low Power: Screen Display “Replace Battery” • Screen Operation o Cycle through info screens on SCROLL button press o Poll and refresh current screen on any button press o Go to setup screen on SELECT / MENU button held for 5 seconds. o Automatically switch to message screen when new message received. 11) Information present on all screens (header) • Date / Time Display o Poll ESP no more than once per 24 hours (per SE spec) o Accuracy within +/-1minute relative to ESP (per SE spec) • Battery/Power Indicator o V>= 2.0v no battery indication o 1.6v <V<2.0v low battery icon- broken battery o V< 1.6v unit shut down. hollow broken battery icon, no link icon, unit off screen “Replace Battery” • Indoor temperature o ⁰C/⁰F user selectable • Wireless link indicator o Cell phone standard 4 bar antenna signal strength graphic 12) Commissioning

LS RESEARCH WIRELESS PRODUCT DEVELOPMENT Rate$aver IHD 7 | Page Rate$aver Datasheet (rev. 1.0) LSR -DS o 5g-peak acceleration o 10-150 Hz o Five cycles per axis in three orthogonal axis • ESD o Per CE approval limits specified in ETS 301-489 and EN 61000-4-2 testing methods

LS RESEARCH WIRELESS PRODUCT DEVELOPMENT Rate$aver IHD 8 | Page Rate$aver Datasheet (rev. 1.0) LSR -DS Absolute Maximum Ratings Rating Value Unit Power Supply Voltage Input 3.5 Vdc Voltage on any digital pin Max 3.6 Vdc RF Input Power +10 dBm Storage Temperature Range -45 to 125 ºC Note: Under no circumstances exceeding the maximum ratings in Table can be allowed. Such a stress may cause permanent damage to the devices Operating Conditions Characteristic Min Typ Max Unit Power Supply Voltage (Vdd) 2.1 3.5 V Input Frequency 2405 2480 MHz Ambient Temperature Range 10 25 70 ºC Logic Input Low Voltage 0 0.7 V Logic Input High Voltage 2.8 3.6 V Radio Electrical Specifications At 25ºC, Vdd = 3.3V for both APEX and APEX LT unless stated otherwise. General Parameter Min Typ Max Unit RF Frequency Range 2400 2483.5 MHz RF Data Rate 250 kbps Microcontroller Operating Frequency 12 MHz Flash Memory 128 kB RAM 5 kB Power Consumption Parameter Min Typ Max Unit Transmit Mode (100mW output) Receive Mode Standby Mode Boost mode is an optional higher performance radio mode that is software selectable to boost receiver sensitivity. Transmitter Parameter Min Typ Max Unit Nominal Output Power 20 dBm

LS RESEARCH WIRELESS PRODUCT DEVELOPMENT Rate$aver IHD 9 | Page Rate$aver Datasheet (rev. 1.0) LSR -DS Programmable Output Power range 32 dB Error Vector Magnitude 15 35 % Receiver Parameter Min Typ Max Unit Receiver Sensitivity (1% PER) – normal mode -92 -96 dBm Receiver Sensitivity (1% PER) – boost mode -93 -97 dBm Saturation (Maximum Input Level) (1% PER) 0 dBm 802.15.4 Adjacent Channel Rejection APEX 35 dB 802.15.4 Alternate Channel Rejection 40 dB 802.11g Rejection (±10 MHz) APEX 40 dB Control DC characteristics Parameter Min Typ Max Unit Logic Input Low 0 0.2VDD V Logic Input High 0.8VDD VDD V Logic Output Low 0 0.18VDD V Logic Output High 0.82VDD VDD V Output source current 4 mA Output sink current 4 mA Output source current 8 mA Output sink current 8 mA I/O pin pull-up and pull-down resistor 30 kΩ Figure 1

LS RESEARCH WIRELESS PRODUCT DEVELOPMENT Rate$aver IHD 10 | Page Rate$aver Datasheet (rev. 1.0) LSR -DS Mechanical Drawing

LS RESEARCH WIRELESS PRODUCT DEVELOPMENT Rate$aver IHD 11 | Page Rate$aver Datasheet (rev. 1.0) LSR -DS Disclaimer LS Research, LLC believes the information in this document is correct and accurate at the time of release. However, LS Research, LLC reserves the right to make changes to this product without notice. Statements Compliance Statement (Part 15.19) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Warning (Part 15.21) Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC Interference Statement (Part 15.105 (b)) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.

LS RESEARCH WIRELESS PRODUCT DEVELOPMENT Rate$aver IHD 12 | Page Rate$aver Datasheet (rev. 1.0) LSR -DS RF Exposure (OET Bulletin 65) To comply with FCC’s and IC’s RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Section 7.1.5 of RSS-GEN Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.

Navigation menu