LifePrint LP001 Lifeprint Photo Printer User Manual manual LP 160816 2

LifePrint Products Inc. Lifeprint Photo Printer manual LP 160816 2

User Manual

555045403530CHECKDRAWN DESIGNNO CODEDWG NOUNIT m/mQ'TYNAMEDATEAPPROTOLSCALEMATERIAL+-TREATMENT MODEL REMARK102520155510 15 20 25 30NO2D3ANEM135 40 45 50 55 60 65DATE CBA50~500~~15015~~5+0.500.30+0.10+0.550.90-+--+0.18-+--0.30+-+-0.90-+1.500.200.10-+-+0.07--+0.05+-+-0.35+0.25CONTENT70 75SIGNA1SIZEDS Global. co., ltd.Description of LED Status IndicatorsDetailsCharging status indicatorOperating statusindicatorCurrentstatusOff Turn on the power to print.Standby/OnWait for print command. Turn off automatically afterthe set time.Charging in progressThe battery is being charged.The battery is fully charged.Charging incompletedOperating/FlashingNo paper, paper jam, cancel operation, cover open, low battery, image not supported, update failure, etc. Power off, image transmission, image processing, printing, cooling standbyError/FlashingCharge indicator LED Status indicator LEDMATERIALPROCESSCMYKCOLOROffset Printing62784391116 1712 131418 19MANUAL USER (Japan) GK07X00001002016.08.08User’s manual症状Safety PrecautionsReorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio, TV technical for help. Only shielded interface cable should be used. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of this device.Safety PrecautionsKeep out of direct sunlight and away from a heat source.Do not place heavy objects on the product.Do not place containers of liquid on the product.Do not spray water directly onto the product when cleaning.Do not place the product in very low temperatures.Do not attempt to disassemble, repair and remodel it for yourself.Do not drop or give it impact. Comply with rated (5V1A) voltage and current.A violation of labeling regulations can cause serious injury or deathWARNINGAny changes or modifications in construction of this device which are not expressly approved by the partyresponsible for compliance could void the user's authority to operate the equipment. Changes and modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.CAUTIONCE WARNINGETSI EN 300 328 V1.9.1ETSI EN 301 489-1 V1.9.2 ETSI EN 301 489-17 V2.2.1EN 60950-1:2006+A11: 2009+A1:2010+A12:2011+A2:2013FCC ID : 2AJH8LP001EN Test Regulations22001 Avoid contact with leaking or a damaged battery.2 Do not short battery teminals.3 Adult supervision is recommended when product is used by young children.4 Avoid areas of excessive heat or moisture.5 Do not disassemble the battery.This product contains electrical or electronicmaterials. The presence of these materialsmay. if not disposed of properly, have potential adverse effects on the environmentand human health. Presence of this label on the product means it should not be disposed of as unsorted waste and must be collected separately. As a consumer, you are responsible for ensuring that this product is disposed of properly. BATTERY WARNINGS It is desirable that it be installed and operated with at least 20cm or more between the radiator and person’s body(excluding extremities:hand,wrists,feet, and ankles) Product specificationsTypeSizePaper size 50 x 76 (mm)Type of supported image file/sizePNG(2550x3300)JPEG(baseline)Within a maximum of 10M ByteProgressive JPEG not supportedPaper used ZINK Paper (for Pomini only)Paper storage conditionsTemperature : 20 ~ 25°CHumidity : 40 ~ 55% RHProduct operating conditionsTemperature : 5 ~ 40°CHumidity : Less than 70% (35°C)Optimal print conditionsTemperature : 15 ~ 32°CHumidity : Less than 70%(32°C)LED display Power on/Standby/Communication/Charge/Error/Print/UpdateCommunication Bluetooth 4.0External connection terminal Micro USB port (charging only)USB power supply Rated DC 5V / 1.0A adapter (optional)Normal operatingvoltageBuilt-in battery 500mAh lithium ion (rechargeable)DC 8V※ Product design and specifications are subject to change without notice.Android : 4.0 or higheriOS : 5.1 or higher(Support may not be provided depending on the user’s Smartphone version and environment.)Support App versionProper image resolution More than 1280 x 2448 pixel Weight 186g Items to check before reporting a malfunctionThe power does not turn on.Check to see if the battery is charged.Problems ChecklistBluetooth connection is not established.Reboot the Bluetooth of the phone, or connect directly from the Settings menu.Try connecting in about 5 minutes after turning on the power to the device.Printing paper seems to be jammed.Stopped during printing operation.The paper is automatically ejected if you turn on the power after turning it off. Print it after printing out the Smart Sheet 2 to 3 times. The printing paper should be stored in an environment with low temperature/humidity. Do not fold or crumble the paper.The power turns off automatically after a certain period of time.Check the Auto Time Off value within “Settings” -> “see more” of the App.(None, 3 minutes, 5 minutes, 10 minutes)The operating status LED flickering Red indicates there is no power remaining on the battery. In this case, charge the battery with a dedicated adapter. The printed photo shows a line.A slash mark appears in the middle of the photo.Print it again after printing out the Smart Sheet 2 to 3 times. (A line may appear in case an impact is applied to the printer during the printing operation.)Problems ChecklistWhite LED flashes and printed paper does not come out.This device requires the proper temperature of (15~32°C) to facilitate smooth printing operation. Thus, a greater warm-up time is required in temperatures that are lower than ideal, and cooling times are greater when the temperature is higher than ideal. Please wait a moment to reach the proper temperature.Printed paper comes out too late.The printed image quality differs greatly from the original image quality.The image quality is somewhat degraded when editing the image using Pomini App’s Edit menu.Print it again after printing out the Smart Sheet 2 to 3 times. The Smart Sheet within the same pack with printing paper should be used.Check to see if the image has the proper resolution (1280x2448) or higher.The printed image quality cannot be guaranteed in case you use printing paper of other companies.Use the original printing paper.Turn on the power after pressing the Reset Hole with a pointed object.The above methods do not resolve the problems.Do not place the product in a hot or humid place.Keep out of the reach of children. Keep away from magnetic interference.Do not place the product in a place with humidity, dust and soot.Wipe it with a dry cloth when cleaning.NOTICEA violation of labeling regulations causes minor injury or damage to theproductDirect CurrentSTAND-BYComponents checkPrintZink photo paperManualUSB CableRerulator sheetCharging the batteryThis device has a built-in battery. Make sure that the battery is charged fully before use.Average charging time: About 1 hour and 30 minutesCharging status indicator Description of statusCharging in progressCharging completedThe use of a non-standard charger can cause malfunction and exception from the subjects of warranty service.Do not give abnormal impacts.NoticeChecking charging status indicatorThere may be the risk of electric shock during the process of charging, so please use with care.Cover Open methodInserting printing paperPrepare the blue Smart Sheet and white printing paper after unpacking the photo printing paper pack.Open the top cover and insert the Smart Sheet and printing paper as shown in the figure.PushOpenApplication Connection and Printing<APP Connection>- Android Connection 1. Select the exclusive APP and execute it after turn on the printer.2. Select the printing menu on the top of the left main screen of APP.3. Press the Connect button.4. Connect the “Lifeprint (XX:XX)” from the searched lists.5. It will be connected with paired printer.6. Be moved main screen automatically after press the printing button on the top of the left screen.7. Press the PRINT QUEUE at the bottom of line.8. Select the image for printing, the image will be saved on waiting list after send the image.- ios Connection 1. Turn on the power of the device.2. For Bluetooth connection, change the mode to “Turn on” [Bluetooth] from [Settings] of the device.3. Connect “Lifeprinter (XX:XX)” in the searched list. (MAC Address can be checked in the label inside the device.) <Printing (both for Android & iOS)>1. Execute the Lifeprint App.2. Select the designed photo on main screen.3. Press the PRINT IMAGE button.4. Press the completed printing button on the top of the right screen after edit on Photo-editor mode.5. Press the SEND button at the bottom of line. ZINK Smartsheet®W888-0134BMust Load! Barcode facing www.ZINK.com装纸时需将此纸放于底部 読み込み時は用紙の１番下に入れてください バーコードを下にして必ず読み込ませてください ! FROM ZINK IMAGINGZink Smart SheetFeaturesProvide optimum image quality correction suitable for each printing paper packRemove foreign objects from printer head.How to useEject automatically before printing out the paper in initial output.Poor quality and occurrence of horizontal lines can be improved by repeatedly printing 2 to 3 times.Recycle until the printing paper of each printing paper pack is exhausted.NoticeOptimum image quality cannot be guaranteed when the Smart Sheet of each printing paper pack is not used, or the bar code is damaged.Long-term storage after opening the printing paper pack can have a bad effect on printing quality due to a discoloration or distortion of printing paper.Function Description connect Setting with Print Battery Battery Gauge indication PRINT COUNT Accumulated total printed images with using printer VERSION Firmware Version indication UPDATE Available or not for Updating LIFEPRINT STORE Move to STORE PRINT QUEUE Waiting list for Printing image <Setting (both for Android & iOS)><Description for Setting>1. Select the Print button on the top of the left screen on Main2. Do setting and checking for each functions on Devices screen.disconnect connectNames of partsTop coverMicro USB Port (only for charging)Push the power buttonReset buttonKesnsington lockCharging IndicatorStatus IndicatorPaper exitTable of ContentsNames of partsPower on/offCharging the batteryCover Open methodInserting printing paperDescription of LED Status IndicatorsComponents checkZink Smart SheetApplication Connection and Printing- APP Connection Android Connection ios Connection - Printing (both for Android & iOS)- Setting (both for Android & iOS)Power on/offONPress the power button for about 3 to 5 seconds.OFFPress the power button for about 2 seconds. NoteWhen you turn on the power, the operating status LED indicator blinks for about 5 seconds. You can print it out when the blinking ends, and the LED is turned on white.67899101112131819Product specificationsItems to check before reporting a malfunction

Navigation menu