LigoWave 27016G Broadband Digital Transmission System with WIFI User Manual 0

LigoWave Inc. Limited Broadband Digital Transmission System with WIFI 0

Contents

user manual

1 Installation Instructions 0.9m 5GHz Standard Performance Dual Polarization Antenna Description This antenna consists of a 0.9m reflector,feed and mounting bracket. The mounting bracket is designed to attach the antenna to a vertical tower pipe of diameterφ60 toφ114mm(2.36”to 4.5”). The mount also provides adjustment ranges of ±30°(±15°fine)elevation and ±180°(±15°fine)azimuth. Notice  The installation instruction must be read before installing the antenna systems.  The installation, maintenance, or removal of antenna systems requires qualified, experienced personnel.  Please verify that the polarization of antenna is required by system after having finished installation. 0.9m Standard Performance Antenna application
2 1. Installing the feed assembly We should install the feed assembly in the reflector, and make the notch of feed locking plate align to the the notch ,then lock it for hex screws M4×12 (4 pieces), as shown in Fig.1. Fig.1 Installing Feed assembly Hex screws M4×12（4件） V-Polarization Notch to notch H-Polarization Feed assembly Notch to notch H-Polarization V-Polarization 2 Feed locking plate
3 2. Installing the mounting bracket At first, we should remove the nut , flat washer, spring washer ,then insert bolts in hole and lock the nut (as show in Fig.2). 3. Installing the support band assembly To ensure safety during mounting bracket and adjustment of the antenna, we should install the support band assembly on pipe at the approximate location, and lock then by bolts M10×130, spring washers and nuts (as show in Fig. 3). Fig.3 Install support band assembly Nut M10 Spring washer10 Bolts M10×130 Pipeφ60mm～φ114mm (Supply by customers) Support band assembly 4 Mounting bracket Fig.2 Install Mount assembly 0.9m Reflector assembly 1 Nut M10 Spring washer 10 Flat washer 10 Bolt M10×30 3 Spring washer 10 Nut M10 Flat washer 10 Nut M10 Bolt M10×40
4 4. Installation of the antenna Lifting and Installing the antenna on pipe, and have the antenna approximately aim at the direction of communication, then tighten the mounting bracket by using boltM10(4sets) as shown in Fig.4. Finally drill one holes (Φ13mm) on the proper position on the tower, connect one side of the strengthening strut assembly to the hole by bolt M12, and connect the other side to reflector by bolt M12. If it is not convenient to have the hole, one can reinforce the antenna by the reinforce assembly and the U-bolt M12 to tower member (See Fig.4). Note: Tighten all strut attachment hardware . U-boltM12 Attach to tower member Fig.6 Install antenna tower pipe Φ60～Φ114mm （supplied by customer） Strengthening strut assembly Bolt M12 Reinforce assembly 5 6 7 Tower member Bolt M12 connect to hole(Φ13mm) Or connect to reinforce assembly Locking the nutM10 （4pieces）
5 5. Adjusting the azimuth and the elevation of antenna After installed antenna and equipment, one can begin to adjust antenna. Loosen the nuts on the orientation adjustment. Adjust the elevation and azimuth again and again, until the optimum orientation of antenna is found. Re-tighten all the loosened bolt and nuts (See Fig.5). Note: Tighten all strut attachment hardware after finishing all adjustment. Loosen bolt to adjust azimuth Loosen and rotate the nuts to adjust azimuth Loosen and rotate the nuts to adjust elevation Loosen the nut to adjust elevation Loosen the nut to adjust elevation Loosen the nuts to adjust azimuth Loosen nuts to adjust azimuth Fig.5 Adjust antenna Loosen nuts to adjust azimuth
6 0.9m 5GHz Standard Performance Dual Polarization Antenna Packing List Item Description Qty Remark 1 0.9m Reflector assembly 1 Include: Feed assembly, Reflector, etc. 2 Feed assembly 1 Include:Feed locking plate,Hex screws M4×12 3 Mounting bracket 1 Include: Bolt M10,nut, flat & spring washer 4 Support band assembly 1 Include: Bolt M10×130,nut, & spring washer 5 Strengthening strut assembly 1 Include: accessories ,boltM12, nut, washer 6 Reinforce assembly 1 7 U-bolt M12 1 Include: nut, washer 8 3mm hexagon ring spanner 1 Used to installing feed assembly 9 Installation instruction 1

Navigation menu