LigoWave 27016G Broadband Digital Transmission System with WIFI User Manual

LigoWave Inc. Limited Broadband Digital Transmission System with WIFI

Contents

User Manual

LigoPTP 6-N RapidFireinstallationPackage contents AC/DC power adapterMounting bracket (3 pc.)802.3af PoE injector M8 bolts (7 pc.)x2x4x1Hardware overview N connectorsLEDsMultifunction buttonMounting bracketGrounding studETH1 PoE INETH2 PoE OUTLigoPTP 6-N RapidFire installationAntena cable connectionGrounding cable connectionETH1 PoE INIMPORTANT: make sure antennas are connected before powering up the device to avoid possible damage.PoE connectionData InDIN rail mountingGroundingData and power Out44-57 VDCPower cord is region dependentLigoPTP 6-N Rapidre
Multifunction buttonClick once the multifunction button to switch LEDs for displaying RSSI level.Each RSSI Signal LED changes color depending on the LigoPTP link’s signal strength from the lowest (am-ber) to the highest (green):Signal LED3 dBm 3 dBm 3 dBmThe stronger signal of the LigoPTP link is, more LEDs are on:-43 to -41 (dBm) -40 to -38 (dBm) -37 to -35 (dBm)-79 to -77 (dBm) -76 to -74 (dBm) -73 to -71 (dBm)-70 to -68 (dBm) -67 to -65 (dBm) -64 to -62 (dBm)-61 to -59 (dBm) -58 to -56 (dBm) -55 to -53 (dBm)-52 to -50 (dBm) -49 to -47 (dBm) -46 to -44 (dBm)≥ -34 dBm (too high)≤ -89 dBm (too low)-88 to -86 (dBm) -85 to -83 (dBm) -82 to -80 (dBm)RSSI Signal level (antenna alignment) indicationLEDsThe Multifunction button, located on the back panel of the LigoPTP RapidFire 6-N (refer to the Hardware overview picture) is able to perform following functions:Activate LED indication Switch to RSSI or Status indication Enable WiFi management radio Reset device to factory defaultsThe LigoPTP 6-N RapidFire has 6 LEDs located on the back panel, which can indicate either main device operation status or RSSI level.After the LigoPTP 6-N RapidFire is powered up, the LEDs display status indications.Switchto RSSI orStatus indication Click Click Hold until 3 Blue LEDs are on Hold until all Blue LEDs start to blinkReset devicetofactacttacorydefaultsHold until all Blue LEDs startrttrtoblinkConnection optionsRemote wireless accessThis is the easiest way to access the web management interface of the newly installed LigoPTP RapidFire device.1. Power off and power on again the LigoPTP RapidFire unit to switch it to a remote wireless management mode. The mode will be switched off automatically in 10 minutes of wireless inactivity.2. Scan for the wireless devices using your phone/tablet and choose the LigoPTP RapidFire wireless network name, which is LigoWave-mng-AABBCC (where AABBCC are the last three bytes of the particular RapidFire MAC address)3. 4. Ethernet accessBy default LigoPTP RapidFire obtains the IP address from the DHCP server thus follow the steps to access device using Windows OS (for information how to access via other OS, refer to http://www.ligowave.com/wiki/faq/):1. Connect your PC to the LigoPTP RapidFire via Ethernet.2. Open Windows Explorer, click on Network drive, and turn on Network discovery:LigoPTP 6-N RapidFire Important informationCopyright © 2018 LigoWaveThis guide and the software described in it are copyrighted with all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permission of LigoWave.Product size and shape are subject to change without prior notice, and actual product appearance may differ from that depicted in the user guide.While the information in this guide has been compiled with great care, it may not be deemed an assurance of The reproduction and distribution of the documentation and software supplied with this product and the use of its contents is subject to written authorization from LigoWave.LigoWave logo is trademark of LigoWave.All other registered and unregistered trademarks in this document are the sole property of their respective owners.4. Double-click on LigoPTP RapidFire icon – you will be redirected to the LigoPTP RapidFire webpage. The 3. Find the required LigoPTP RapidFire icon:If the LigoPTP RapidFire is unable to obtain IP address from a DHCP server, it fallback to the default static IP 192.168.2.66. LigoPTP 6-N RapidFireLigoPTP 6-N RapidFire-Antenna Type External AntennaMax. Tx power (dBm) Up to 30 dBm (country dependent)Max. EIRP (dBm) Connected antenna gain dependentSupported frequencies range 5.900-6.400 GHzPower supply PoE 802.3at, isolated 42 - 57 VDCPower consumption (max) 8.6WLigowave 138 Mountain Brook Drive Canton, GA 30115 United States of America For support: support@ligowave.com For sales enquiries: sales@ligowave.comZalgirio st. 92, Entrance 1, Floor III Vilnius, LT-09303, Lithuania support@ligowave.comManufacturer: LigoWave Inc. Limited, UnitD, 16/F., MG Tower, 133 Hoi Bun Road, Kwun Tong, Kowloon, Hong KongContact informationTechnical support If you encounter problems when installing or using this product, please consult the LigoWave website at www.LigoWave.com for:• Direct contact to the LigoWave support centers.• Frequently Asked Questions (FAQ).• Download area for the latest software, user documentation and product updates.192.168.111.1This device requires a professional installation.Please refer to the “0.9m5GHz dual polarization(N-type)professional installation instructions” for specific installation steps.
FCC Warning: If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID:2AR4D-27016G”, when the module is installed inside another device, the user manual of this device must contain below warning statements; 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This modular complies with FCC RF radiation exposure limits for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 400 cm between the radiator and user body. The device outdoor use only for 5935MHz~6390MHz. And antenna request need to follow Part 101.115 of the FCC antenna standard Rules as below picture .

Navigation menu