Linksys Wet54G Quick Start Guide UK EU LA_V2 QIG Rev_NC
Wet54G-Eu V2 Qi,0 WET54G-EU_v2_qi,0 WET54G-EU_v2_qi,0 s s.linksys.com 3:
Wet54G-Eu V2 Qi WET54G-EU_v2_qi WET54G-EU_v2_qi 1224640138371 quickinstall s s.linksys.com 3:
2014-07-06
: Linksys Linksys-Wet54G-Quick-Start-Guide linksys-wet54g-quick-start-guide linksys pdf
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
® A Division of Cisco Systems, Inc. Package Contents • • • • • • • • Wireless-G Ethernet Bridge Setup CD-ROM User’s Guide on CD Quick Installation Guide Detachable Antenna RJ-45 Network Cable One Pair of Bridge Stands Power Adapter 2,4GHz Wireless-G 802.11g Ethernet Bridge Wireless Model WET54GNo. (UK/EU/LA) v2 Model No. Quick Installation Guide 1 1 A B C D 2 Connect the Wireless-G Ethernet Bridge for Setup Attach the detachable antenna. Plug the included Ethernet network cable into the LAN port on the back panel of the Bridge. Plug the other end of the Ethernet network cable into the RJ-45 port of the hub, switch, or PC you wish to use to configure the Bridge. Plug the supplied power adapter into the Power port on the back panel of the Bridge. Then plug the other end into an electrical outlet. B D 2 A B C D Set up the Wireless-G Ethernet Bridge Insert the Setup CD-ROM into your PC’s CD-ROM drive. The Setup Utility should run automatically, and the Welcome screen should appear. If it does not appear, click the Start button and choose Run. In the field that appears, enter D:\setup.exe (if “D” is the letter of your CD-ROM drive). A Click Setup to begin the setup process. Make sure the Bridge is correctly connected to your wired network. Click Next. The screen displays a list of Wireless-G Ethernet Bridges on your network, along with their status information. Select the Bridge you are currently installing by clicking its name in the Selection box. Click Yes. C D 3 E F A Password screen will appear. In lowercase letters, enter admin in the Password field. Then click Enter. The Mode Settings screen will appear. Select Infrastructure if you want your wireless computers to communicate with computers on your wired network using a wireless access point. Select Ad-Hoc if you want wireless computers to communicate directly with each other. In the WB Name field, enter a unique name for the Bridge. Click Next. G F On the Wireless Settings screen, enter your wireless network’s SSID. If you chose AdHoc mode, select the channel that your network uses. If you have Wireless-G (802.11g) and Wireless-B (802.11b) devices in your network, then keep the default Network Mode setting, Mixed. If you have only Wireless-G devices, select G-Only. Then click Next. 4 E G H The IP Settings screen will appear. If your network has a DHCP server, select Automatically obtain an IP address (DHCP). Click Next and proceed to step I. If your network does not have a DHCP server, select Set IP configuration manually. Enter an IP Address, IP Mask (also known as Subnet Mask), and Gateway. H NOTE: The default IP address of the Bridge is 192.168.1.226. You must specify an IP address. If you are unsure about the IP Mask and Gateway, leave these two fields blank. Click Next. 5 I On the Security Settings screen, set the level of encryption you want for your network, and select the Passphrase(s) and/or encryption keys. With WPA PSK, or Pre-Shared Keys, you have two encryption options, TKIP and AES, with dynamic encryption keys. Select the type of algorithm, TKIP or AES. Enter a WPA Shared Key of 8-32 characters. The WEP key can consist of the letters “A” through “F” and the numbers “0” through “9” and should be 10 characters in length for 64-bit encryption or 26 characters in length for 128bit encryption. If you entered a Passphrase, the WEP key will be generated automatically. Click the Next button to continue. 6 I J K Review your settings on the Confirmation screen. Write down the Bridge’s IP Address if you want to access the Bridge’s Web-based Utility. Click Yes to save these settings. On the Congratulations screen, click Exit. J K 7 43 A B C Connect the Wireless-G Ethernet Bridge for Network Use After configuration, unplug the power adapter from the electrical outlet, and unplug the Ethernet network cable from the PC. Plug the Ethernet network cable into the RJ-45 port on the Ethernet-ready network device you wish to add to the wireless network. Plug the power adapter into a local electrical outlet. NOTE: The Bridge features Power over Ethernet (PoE) support. PoE technology allows a PoE adapter (also known as a power injector, power hub, or inline power device) to supply data and power to an Ethernet device using a single Ethernet network cable. To use the Bridge’s PoE feature, follow the instructions for your specific PoE device. Congratulations! The installation of the Wireless-G Ethernet Bridge is complete. For additional information or troubleshooting help, refer to the User Guide on the CD-ROM or the Technical Support Insert. You can also e-mail for further support. Website http://www.linksys.com/international Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2004 Cisco Systems, Inc. All rights reserved. WET54G-UK-EU-LA_V2-QIG-40219NC JL 8
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Modify Date : 2004:02:20 16:11:24Z Create Date : 2003:10:02 13:43:30Z Page Count : 8 Creation Date : 2003:10:02 13:43:30Z Mod Date : 2004:02:20 16:11:24Z Producer : Acrobat Distiller 5.0.5 (Windows) Author : junelee Metadata Date : 2004:02:20 16:11:24Z Creator : junelee Title : WET54G-UK-EU-LA_V2-QIG-Rev_NC.fm Page Mode : UseNoneEXIF Metadata provided by EXIF.tools