Lotek Wireless SRX600 Telmetry Receiver User Manual Guide to Keypad and LCD display

Lotek Wireless, Inc Telmetry Receiver Guide to Keypad and LCD display

Contents

Guide to Keypad and LCD display

1 of 20Revision D, #10055, March 16th, 2005Guide to the SRX 600 Keypad and LCD Display
2 of 20Revision D, #10055, March 16th, 2005UNDERSTANDING THE LCD/KEYPAD LAYOUT The keypad and LCD display define the interface through which the receiver is programmed. The program is designed like a hierarchy. All aspects of the program are accessed through keys on the keypad. Keys labelled Setup, Log On, Info, Manual, Codelog and Set Delta provide access to menus (note that in most cases there are also sub-menus). Three of these keys are referred to as modes: Setup, Manual and Codelog. Through these modes, specific aspects of the receiver’s functionality can be enabled, disabled or amended. The keypad is used to enter or select operating parameters, input data and for navigate through menus and pages. Every key, except Light, has two functions. Which function is accessible depends on the state of the receiver.The LCD display is a two line display that is used to request input, either in the form of a menu selection or the entry of a numeric value. It is necessary to spread out the information, therefore the display shows what is referred to as a page, whereby a menu item can link to more than one page. Scroll through pages using the right and left arrow keys or the END/ESC key. The LCD display also provides current setting information. This information depends on whether the receiver is Online or Offline. • If the receiver is Online then the display shows current settings within brackets after the title of a page (e.g. Scan Options) and still allows a new value to be entered. • If the receiver is Offline then the display shows current settings after the title of a page, but there is no provision for a new value to be entered. STARTING THE RECEIVER After turning on the receiver the sequence of messages on the LCD screen will be similar to the following: The last page shows if there is a user logged onto the receiver (Online) or not (Offline) and it also displays the mode that the receiver was in (e.g. Setup). SRX600 BOOT CODE V2.5 LOTEK WIRELESS INC. SRX600 BOOT CODE V2.5 SYSTEM STARTUP (1) ... USER: NONE (OFFLINE) MODE: SETUP
3 of 20Revision D, #10055, March 16th, 2005Log OnILogging on to the receiver provides the ability to change the state of the receiver. When a log on password is provided the receiver is considered Online. If no password is provided (logged off) then the receiver is Offline. The differences between Online and Offline are described below:• Offline: the receiver allows only read access, which means that most inputs are not allowed unless a log on password is provided. The only input allowed is the Reset Password function. • Online: the receiver allows full write access, which means that all functionality and input capability are available.Log on to the receiver via Log On > 1)Log On or Log On > 2)Log On via Factory Password. Wait a few seconds for the changes to be accepted and then the receiver returns to the last state that was active (e.g. scan) or the start page.The log on password is always 123456 unless it is changed via Setup > 3)Change Password. Logging on via the factory password provides the ability to log on quickly, as long as the factory password (123456) is being used. This feature is convenient for people who do not need or want to have a specific confidential password.Logging on can be done at any time during the operation if the receiver, except while using the Info key and its menu items. LOGGING OFF Logging off can be done at any time during the operation of the receiver, which means that data collection can continue while limiting access to settings via a password. Logging off means the receiver is Offline.Log off from the receiver via Log On > 2)Log Off or Log On > 3)Temporarily Log Off. Wait a few seconds for the changes to be accepted and then the receiver returns to the start page (first information shown after receiver turns on).Temporarily logging off creates a restriction, whereby logging on is only accessible from the keypad and no longer accessible from the SRX Host software, except via the Host’s Keypad Simulator.
4 of 20Revision D, #10055, March 16th, 2005Setup mode SETUP: 1)COMM 2)TIME 3) RESET/CHANGE PASSWORD CONFIGURE COMM: 1)SERIAL I 2) SERIAL II1) Configure2) Factory Settings SET TO FACTORY SETTINGS: (SERIAL, 115200, 8, N, 1) 1) SERIAL I 2) SERIAL II1) Serial I2) Serial II SERIAL ##: 1)BAUD RATE 2) PARITY 3) DATA BITS 4) STOP BITS 5)MODEM1) Baud Rate2) Parity3) Data Bits4) Stop Bits SERIAL BAUD RATE (1): 1)115200 2)57600 3)38400 4)19200 5)9600 6)4800 7) 2400 8)1200 9) 600 SERIAL PARITY(1): 1)NONE 2)ODD 3)EVEN SERIAL DATA BITS(2): 1) 7 BITS 2) 8 BITS SERIAL STOP BITS(1): 1) 1 BIT 2) 2 BITS1) COMM COMM (CYCLE POWER OFF/ON) 1)CONFIGURE 2)FACTORY SETTINGS MODEM 1) HAS MODEM 2) VIEW CMDS 3) INITIALIZE 5) Modem2) Time - see page 53) Reset/Change Password - see page 5 SERIAL I HAS MODEM (9) 7) YES 9) NO MODEM INIT CMD1: ATZ0 NO MODEM, PLEASE SELECT IT VIA ‘SETUP/COMM’1) Has Modem2) View CMDS3) Initialize
5 of 20Revision D, #10055, March 16th, 2005 TIME (11:24:33 17/06/04): 1)GMT CORRECTION 2)LOCAL DATE 3)LOCAL TIME1) GMT Correction2) Time GMT CORRECTION (-05:00): (HH:MM) > --2) Local Date LOCAL DATE (17/06/04): (DD/MM/YY)>3) Local Time LOCAL TIME (11:24:33): (24HH:MM:SS)>3) Reset/Change Password RESET PASSWORD (630387): (XXXXXX)> CHANGE PASSWORD (******): (OLD/NEW)> OR LOCAL DATE (17/06/04): (DD/MM/YY)>
6 of 20Revision D, #10055, March 16th, 2005Manual mode MANUAL: 1)CODE SET 2)SEARCH 3)SIGNAL 1) Code Set CODE SET(1): 1)LOTEK 2 2)LOTEK3 3) LOTEK42) Search ... see page 73) Signal ... see page 8 CODE SET: LOTEK 2 OR
7 of 20Revision D, #10055, March 16th, 2005 SEARCH (FROM 148.516MHZ): 1)START 2)GAIN 3)MIN FREQ 4)MAX FREQ 5)FREQ STEP 6)SCAN TIME 7)NOISE THRESHOLD1) Start SEARCH 148.220MHZ ID AH0=40 0) PAUSE SCAN 1) CODE SET 2)SHOW BEEP/ID/SENSOR 3)SET 4)GPS 5) INC. FREQ. 6)DEC. FREQ. 7)EN/DIS NOISE BLANK 8) INC. GAIN 9)DEC. GAIN GAIN (87): (00-99) >2)Gain FOUND: I184 S121 10:54:21 148.220MHZ CODE GAIN =33 0) PAUSE SCAN 1) CODE SET 2)SHOW BEEP/ID/SENSOR 3)SET DELTA 4)GPS 5) INC. FREQ. 6)DEC. FREQ. 7)EN/DIS NOISE BLANK 8) INC. GAIN 9)DEC. GAIN MIN FREQ (148.000MHZ): (148-152.000MHZ) > MAX FREQ (152.000MHZ): (148-152.000MHZ) > FREQ STEP (002KHZ): (001-999KHZ) >3)Min Freq4)Max Freq5)Freq Step NOISE THRESHOLD (40): (00-99) >7)Noise Threshold SCAN TIME (2.2S): (0.1-9.9SEC) >6)Scan Time PAUSE: I999 S102 11:13:46 148.220MHZ AH0=40 0) RESUME SCAN 1) CODE SET 2)SHOW BEEP/ID/SENSOR 3)SET DELTA 4)GPS 5) INC. FREQ. 6)DEC. FREQ. 7)EN/DIS NOISE BLANK 8) INC. GAIN 9)DEC. GAIN0)Pause ScanManual Mode > 2) Search
8 of 20Revision D, #10055, March 16th, 2005 SIGNAL: 1)START 2)GAIN 3)ANT 4)FREQ 5)NOISE THRESHOLDManual Mode > 3) Signal SIGNL: I999 S102 11:13:46 148.220MHZ ID AH0=40 1) CODE SET 2)SHOW BEEP/ID/SENSOR 3)SET DELTA 4)GPS 5) INC. FREQ. 6)DEC. FREQ. 7)EN/DIS NOISE BLANK 8) INC. GAIN 9)DEC. GAIN5)Noise Threshold1)Start3)Ant2)Gain4)Freq ANT(0): (AH0=0, ASP8=1-8)> GAIN(87): (00-99)> FREQ(149.010MHZ): 1)RADIO 2)ACOUSTIC NOISE THRESHOLD(40): (00-99)> 1)Radio2)Acoustic RADIO FREQ(149.010MHZ): (148-152.000MHZ)> ACOUSTIC FREQ(NONE): (000-999KHZ)>
9 of 20Revision D, #10055, March 16th, 2005Codelog Mode CODELOG: 1)CONFIG# 2)SCAN 3)MASTER FTABLE1)Config(#1) ... see page 102)Scan ... see page 163) Master FTable ... see page 17
10 of 20Revision D, #10055, March 16th, 2005 CONFIG(#3): 1)NEW CFG# 2)SCAN SETTINGS 3)FREQ/CH 4)ANT/HYDR 5)FILTERS 6)SENSORS 1)New Cfg# NEW CFG#(3): (1-8)> FREQ/CH (10): 1)ADD 2)VIEW/MODIFY 3)VIEW/MODIFY ALL3)Freq/CH4)Ant/Hydr ... see page 125)Filters ... see page 13 ADD FREQ/CH: 1)RADIO 2)ACOUSTIC1)Add2)View/Modify ADD RADIO FERQ(#11): (148-152.000MHZ)> ADD ACOUSTIC FREQ(#11) (000-999KHZ)>1)Radio2)Acoustic2)Scan Settings ... see page 116)Sensors ... see page 151)Config(#1)2)View/Modify All 149.891MHZ CH456 EN ID: 1)DEL 2)EN/DIS 3)ID/SEN ALL FREQ/CH(2, 4): 1)DEL 2)EN 3)DIS 4)ID 5)SEN Codelog Mode > 1)Config#1
11 of 20Revision D, #10055, March 16th, 20052)Scan Settings SCAN SETTINGS: 1)CODE SET 2)PARAM 3)OPTIONS 4)SITE NUMBER2) Param3) Options 4) Site Number1) Code Set PARAM: 1)SCAN TIME 2)TOTAL SCAN TIME 1) Scan Time2)Total Scan Time SCAN TIME(18.1S): (00.1-99.9SEC)> TOTAL SCAN TIME(47:59): (MM:SS)> SCAN OPTIONS: 1)TOA 2)CRTO 3)AGC 4)GPS CRTO(2): DIS 1)EN/DIS 2)TIMEOUT GPS: DIS CLK, DIS POS 1)EN/DIS CLK 2)EN/DIS POSITION AGC(1): 1)ENABLE 2)DISABLE2) CRTO4) GPS 3) AGC CODE SET(1): 1)LOTEK2 2)LOTEK3 3)LOTEK4 SITE NUMBER(1234): (0000-9999)>1) TOA TOA(2): 1)ENABLE 2)DISABLECodelog Mode > 1)Config#1 > 2)Scan Settings
12 of 20Revision D, #10055, March 16th, 20054)Ant/Hydr ANT/HYDR: 1)USE ASP8 2)GAIN 3)ANT 4)HYDR 5) PRIORITY1)Use ASP83)Ant4)Hydr2)Gain USE ASP8 1)YES 2)NO ANT: 1)RADIO ANT GRP 2)RADIO MASTER ANT HYDR:1)ACOUSTIC HYDR GRP 2)ACOUSTIC MASTER HYDR GAIN: 1)ASP8 GAIN 2)AH0 ANT GAIN 3)RADIO MASTER GAIN 4)ACOUSTIC MASTER GAIN RADIO ANT GRP(123): (1-8)> HYDR GRP(567): (1-8)> ACOUSTIC MASTER HYDR(0): (GRP=0 ASP8=1-8 NO=9)> ASP8 GAIN (40,21,33,54,22, 36,47,18): PORT #(1-8)> AH0 ANT GAIN(33): (00-99)>1)ASP8 Gain 2) AH0 ANT Gain3)Radio Master Gain4)Acoustic Master Gain RADIO AMG GAIN(40): (00-99)> ACOUSTIC HM3 GAIN(60): (00-99)>5)Priority PRIORITY: FREQ, DIS MPVIEW 1)FREQ/ANT 2)EN/DIS MASTER PREVIEWCodelog Mode > 1)Config#1 > 4) Ant/Hydr RADIO MASTER ANT(9): (GRP=0 ASP8=1-8 NO=9)>
13 of 20Revision D, #10055, March 16th, 20055) Filters FILTER: 1)FILTER TYPE 2)SET REJECT CH/ID 3)SET ACCPET CH/ID 4)SET REJECT ID 5)SET ACCEPT ID1) Filter Type FILTER TYPE (3): 1)NO FILTER 2)REJECT CH/ID 3)ACCEPT CH/ID 4)REJECT ID 5)ACCEPT ID2) Set Reject CH/Id3) Set Accept CH/Id4) Set Reject Id5) Set Accept Id SET REJECT CH/ID (32): 1)ADD 2)VIEW/DEL SET ACCEPT CH/ID (20): 1)ADD 2)VIEW/DEL SET REJECT ID (29): 1)ADD 2)VIEW/DEL SET ACCEPT ID (10): 1)ADD 2)VIEW/DEL1) Add2) View/Del1) Add1) Add1) Add2) View/Del2) View/Del2) View/Del ADD REJECT CH/ID (#33): (XXX/XXX)> REJECT CH880 ID110 (#20): 1)DEL ADD ACCEPT CH/ID (#21): (XXX/XXX)> ACCEPT CH240 ID211 (#11): 1)DEL ADD ACCEPTID (#11): (XXX)> ACCEPT ID211 (#03): 1)DEL REJECT ID450 (#25): 1)DEL ADD REJECT ID (#30): (XXX)> FILTERS: 1)ID FILTER 2)PULSE FILTER1) ID Filter2) Pulse Filter ... see page 14Codelog Mode > 1)Config#1 > 5)Filters SET REJECT ID (29): 1)ADD 2)VIEW/DEL
14 of 20Revision D, #10055, March 16th, 2005 PULSE FILTER: 1)ECHO 2)NOISE THRESHOLD 3)PULSE WIDTH 4)SIGNAL STRENGTH DEV2) Pulse Filter ECHO FILTER (020MS): (000-255)> NOISE THRESHOLD (30): (00-99)> MIN 2.0MS PULSE WIDTH (1): 1)ENABLE 2)DISABLE MAX 18 SIGNAL S DEV (2): 1)ENABLE 2)DISABLE1) Echo 2) Noise Threshold 3) Pulse Width 4) Signal Strength Dev Codelog Mode > 1)Config#1 > 5)Filters > 2)Pulse Filter
15 of 20Revision D, #10055, March 16th, 20056) Sensors SENSORS: 1)CLASS 2)TYPE 3)PARAM SENSOR CLASS(0): (0-9)> SENSOR TYPES(123): (1=C 2=PSI 3=ACT 4=EMG)> SENSOR PARAM: 1)C 2)PSI 3)ACT 4)EMG1) Class 2) Type 3) Param C[-6.0, 34.0]/50): 1)MIN 2)MAX 3)LEVEL PSI[0.0, 50.0]/51): 1)MIN 2)MAX 3)LEVEL ACT ([0, 1]/2): 1)MIN 2)MAX 3)LEVEL EMG ([0.0, 50.0]/51): 1)MIN 2)MAX 3)LEVEL1) C 2) psi 3) ACT 4) EMG MIN(-0006.0 C): >-- MAX(+0034.0 C): >+ C LEVEL(050): (001-255)> MIN(+0000.0 PSI): >+ MAX(+0050.0 PSI): >+ PSI LEVEL(050): (001-255)> ACT MIN (0): > ACT MAX (1): > ACT LEVEL(2): (1-9)>Codelog Mode > 1)Config#1 > 6)Sensors MIN(+0000.0 EMG): >+ MAX(+0050.0 EMG): >+ EMG LEVEL (051): (001-255)>
16 of 20Revision D, #10055, March 16th, 2005 SCAN(3712 KBYTES FREE): 1)CONTINUE TO LOG DATA 2)DEL ALL DATA (PASSWORD)1) Continue to Log Data SCAN: I243 S100 14:22:33 148.220MHZ CH800 AMG=33 0)PAUSE SCAN 2)VIEW 3)SET DELTA 4)GPS 7)EN/DIS NOISE BLANK 8)INC. GAIN 9)DEC. GAIN DEL ALL DATA (PASSWORD): (XXXXXX)>2)Del All Data (password) DISPLAY SCROLL: 0 OF 64 DETECTION 0) Pause Scan2) ViewCodelog Mode > 2)Scan2) Scan PAUSE: I243 S100 14:22:33 148.220MHZ CH800 AMG=33 0)RESUME SCAN 1)FILTERS 2)VIEW 3)SET DELTA 4)GPS 5)INC. FREQ 6)DEC.FREQ 7)EN/DIS NOISE BLANK 8)INC. GAIN 9)DEC. GAIN VIEW: 1)DISPLAY SCROLL 2) TEMP, PRESSURE UNITS TEMP, PRESSURE (C, PSI): 1)C/F 2)PSI/M 3) Set SET DELTA : 1)FREQ 2)GAIN DELTA FREQ(001 KHZ): (001-999)> DELTA GAIN(02): (01-99)> 4) GPS GPS(OFF) : NOT ENABLED1)Filters ... refer to page 13
17 of 20Revision D, #10055, March 16th, 2005Codelog Mode > 3)Master Ftable MASTER FTABLE: 1)UUC FREQ 2)VIEW MASTER FTABLE1)UUC Freq UUC FREQ(150.000MHZ): (148-152.000)>2) Master F Table 148.000MHZ CH001 #1 IS IN CFG: #1,2,43) Master FTable
18 of 20Revision D, #10055, March 16th, 2005SET Delta SET DELTA : 1)FREQ 2)GAIN DELTA FREQ(001 KHZ): (001-999)> DELTA GAIN(02): (01-99)>
19 of 20Revision D, #10055, March 16th, 2005GPS Before GPS fix ...After GPS fix ...Other possible message ... TEST GPS: TIME + POSITION TEST GPS: 15:34:27 (GMT) -44.0627687 79.4467891 TEST GPS: TIME + POSITION ANTENNA OPEN DETECTED
20 of 20Revision D, #10055, March 16th, 2005

Navigation menu