Lutron Electronics 0017 Car Visor Control User Manual JPZ0017

Download:
Mirror Download [FCC.gov]
Document ID	170760
Application ID	JN7Vf5jZxbbJ3/stdicUGA==
Document Description	JPZ0017 User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	48.33kB (604118 bits)
Date Submitted	2001-09-21 00:00:00
Date Available	2001-09-21 00:00:00
Creation Date	2001-09-19 09:22:02
Producing Software	Acrobat PDFWriter 4.05 for Windows NT
Document Lastmod	0000-00-00 00:00:00
Document Title	Car Visor Operation and Installation Manual 9-17.PDF
Document Creator	Microsoft Word - Car Visor Operation and Installation Manual 9-17.doc
Document Author:	emcbackup

Preliminary RadioRA Car Visor Control Instructions
09/19/01
Adding a Car Visor Control
The Car Visor Control is a special type of Master Control. The System can have a maximum of
12 Master Controls. For every 1 Master Control NOT used, a Car Visor Control may be used in
its place.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures: Reorient or relocate the receiving antenna. Increase the separation between the
equipment and receiver. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by Lutron Electronics could void the
user’s authority to operate this equipment.
Step 1
Begin Control Activation
Press and hold the ACTIVATE CONTROLS
button on any Repeater until the green
ACTIVATE CONTROLS LED turns ON
(approximately 3 seconds).
Middle row of LEDs will turn ON when the
Master Control has been activated.
Car Visor Receive r
Step 3 Complete Car Visor
Control Activation
Step 2 Activate Controls
Press and hold the ACTIVATE CONTROLS
button on any Repeater until the green
ACTIVATE CONTROLS LED turns OFF
(approximately 3 seconds).
To add a Car Visor Control
Press any button.
• All LEDs will flash, then
• Top and bottom row will flash alternately
The green ACTIVATE CONTROLS LED on
ALL Repeaters will turn OFF. The MAIN or
AUXILIARY LED will remain on.
Page 1 of 10
Preliminary RadioRA Car Visor Instructions
09/19/01
Programming Preparations
Assigning the Lights Column of Buttons as
ROOMS or SCENES on your Car Visor Control
The right most column of buttons on a Car Visor Control can be programmed to be either ROOM
or SCENE buttons.
Step 1 Begin ROOM/SCENE
Step 2 Changing ROOM/SCENE
Assignment
Assignments
Simultaneously press and hold the 3rd,5th,
and ALL OFF buttons in the right most
column until an LED in the right most
column of the Car Visor Control which you
are programming begins to flash
(approximately 3 seconds).
Press the 1st button in a column to make
that column a ROOM column, or press the
2nd button to make it a SCENE column.
Step 3
Changing the closure
type for the Input buttons
Both CCI’s can be independently selected
as Momentary or Maintained closures.
Continued on next page.
Page 2 of 10
Preliminary RadioRA Car Visor Instructions
09/19/01
Step 3
Step 5 Label columns
Changing the closure
type for the Input buttons
(continued)
If a CCI is set as Momentary (default
setting), its LED will be OFF. If a CCI is set
as Maintained, its LEDs will be ON.
Apply the supplied ROOMS or SCENES
labels to the space provided over the right
most button column.
To change the setting to Maintained, press
and hold the CCI button until the LED turns
ON.
To change the setting to Momentary, press
and hold the CCI button until the LED turns
off.
Step 4 Complete ROOM/SCENE
Assignment
Simultaneously press and hold the 3rd, 5th,
and ALL OFF buttons in the right most
column until the LEDs stop flashing
(approximately 3 seconds).
Page 3 of 10
Preliminary RadioRA Car Visor Instructions
09/19/01
Assigning Dimmers, Switches, or GRAFIK Eye
Control Units to Car Visor Control Buttons
Step 1 Begin assigning
Step 2 Select a Button
Dimmers, Switches, or GRAFIK
Eye® Control Units to buttons
Press the button that you want to program.
Its LED will begin to flash.
Simultaneously press and hold the 2nd and
4th buttons in the right most column until the
upper right LED begins to flash
(approximately 3 seconds).
Valid Car Visor buttons that can to be
programmed are the right most column
buttons, ALL ON, ALL OFF, Inputs, or
Security FULL and FLASH buttons.
Upper right LED flashes.
Page 4 of 10
Preliminary RadioRA Car Visor Instructions
Step 3 Assign a Dimmer,
Switch, or GRAFIK Eye Control
Unit to the button.
Notes:
• Multiple Dimmers, Switches, or GRAFIK
Eye ® Control Units can be assigned to a
button.
09/19/01
If you assign the wrong Dimmer, Switch, or
GRAFIK Eye ® Control Unit to the Car Visor
Control button, turn the Dimmer, Switch, or
GRAFIK Eye ® Control Unit OFF to unassign
it.
Note: GRAFIK Eye ® Control Units will
automatically turn on to scene 1 once
assigned.
• Controls must be assigned to a Car Visor
Control button while its LED is flashing.
Step 4 Select a Button
Assign Dimmers or Switches to the Car
Visor Control button by turning the Controls
ON.
2-3 until all buttons are programmed. When
finished, proceed to Step 5.
Assign a GRAFIK Eye ® Control Unit to the
Car Visor Control button by changing the
selected GRAFIK Eye ® scene.
Step 5 Complete assigning
Dimmers, Switches, or GRAFIK
Eye® Control Units to buttons
Simultaneously press and hold the 2nd and
4th buttons in the right most column until all
LEDs begin to flutter (approximately 3
seconds).
Page 5 of 10
Preliminary RadioRA Car Visor Instructions
09/19/01
Setting Light Levels/Grafik Eye Scene Selection
for ROOM Buttons
Setting Light Levels/ Levels/Grafik Eye Scene for
SCENE Buttons
This section is not complete yet…
For this option, refer to the “Setting Light Levels” section of the
RadioRA Setup Guide
- Use Pages 1-11 and 1-12 for ROOM Buttons
- Use Pages 1-15 and 1-16 for SCENE Buttons
Page 6 of 10
Preliminary RadioRA Car Visor Instructions
09/19/01
Programming a Car Visor Transmitter
The Car Visor Control can learn a maximum of 7 Car Visor Transmitters.
Step 1 Begin Learning a
Step 2 Select the Receiver
Transmitter to the Receiver
Button to be learned to the
Transmitter Button
Press and hold the LEARN button
(approximately 3 seconds) on the Car Visor
Receiver until the LED turns on.
Press and hold the Receiver button
(approximately 3 seconds) that the
Transmitter button will be learned to until the
corresponding LED turns on. If the ALL ON
button is pressed, the right most column of
LEDs will flash upward. If the ALL OFF
button is pressed, the right most column of
LEDs will flash downward.
Page 7 of 10
Preliminary RadioRA Car Visor Instructions
Step 3 Learn the Transmitter
Button to the Receiver
09/19/01
The receiver button turns off indicating that
the transmitter button has been learned to
the receiver button.
Press and hold the Transmitter button
(approximately 3 seconds) until the LED of
the selected Receiver button flashes for 3
seconds. If the transmitter is learned to the
ALL ON button, the LEDs in the right most
column will rapidly flash upward for 3
seconds. If the transmitter is learned to the
ALL OFF button, the LEDs in the right most
column will rapidly flash downward for 3
seconds.
The Transmitter button may be learned to
any one of the ROOM/SCENE, ALL ON,
ALL OFF, Input, Output, or both FULL ON
and FLASH buttons.
To verify that the Transmitter Button has
been learned to the Receiver Button, press
the Transmitter button again. The
corresponding Receiver button LED will
begin to flutter indicating that the Transmitter
button is learned to the Receiver button.
To unlearn a Transmitter button, repeat
Steps 2 and 3 for the desired button(s).
Step 4 Select and learn the next
Transmitter Button to the Receiver
Button
Repeat Steps 2 and 3 for any remaining
Transmitter buttons to be learned to
Receiver Buttons. Proceed to Step 5 when
all Transmitter buttons have been learned.
Step 5 Select the next
Transmitter
Repeat Steps 2-4 for any remaining
Transmitters. Proceed to Step 6 when all
Transmitters have been activated.
The learned receiver button flashes for 3
seconds before turning off.
Page 8 of 10
Preliminary RadioRA Car Visor Instructions
09/19/01
Step 6 Complete Transmitter
Activation
Press and hold the LEARN button on the
Car Visor Receiver (approximately 3
seconds) until the LED turns off.
Page 9 of 10
Preliminary RadioRA Car Visor Instructions
09/19/01
Returning the Car Visor Control to Default Factory
Settings
Step 1 Begin returning to
Step 2 Complete returning to
default factory settings
default factory settings
st
rd
th
Press and hold the 1 3 and 5 buttons in
the right most column until the
corresponding LEDs begin to flash
(approximately 3 seconds).
st
rd
th
While the 1 , 3 , and 5 LEDs are flashing,
nd
th
press and hold the 2 and 4 buttons in the
right most column until all LEDs flash.
All LEDs will turn OFF, indicating that the
Car Visor Receiver has been returned to
Default Factory Settings
LEDs will flash for only 3 seconds.
Page 10 of 10

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 10
Creator                         : Microsoft Word - Car Visor Operation and Installation Manual 9-17.doc
Create Date                     : 2001:09:19 09:22:02
Title                           : Car Visor Operation and Installation Manual 9-17.PDF
Author                          : emcbackup
Producer                        : Acrobat PDFWriter 4.05 for Windows NT

EXIF Metadata provided by EXIF.tools