Lutron Electronics 0020 HRD-5KP User Manual RF KP Instr
Lutron Electronics Company Inc HRD-5KP RF KP Instr
USERS MANUAL FOR HRD TRANCEIVER
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 285199 |
| Application ID | SoPXmNI7pp+7o268BXXxMA== |
| Document Description | USERS MANUAL FOR HRD TRANCEIVER |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 41.87kB (523326 bits) |
| Date Submitted | 2002-11-22 00:00:00 |
| Date Available | 2002-11-18 00:00:00 |
| Creation Date | 2002-11-14 11:50:14 |
| Producing Software | Acrobat Distiller 5.0.5 (Windows) |
| Document Lastmod | 2002-11-14 11:50:14 |
| Document Title | RF KP Instr.qxd |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | rlau |
Installation Instructions RF Designer-Style Keypads Please Read Before Installing HRD-5KP, -5RL, -10KP, -10RL 120/127VAC, 50/60Hz Overview HRD-5KP HRD-5RL HRD-10KP HRD-10RL The HRD-5KP, -5RL and HRD-10KP, -10RL keypads are for use with HomeWorks systems. The keypad buttons are programmed with a personal computer using the HomeWorks Utility. Up to 32 keypads, each with a unique address, can be assigned to each HomeWorks RF Processor. Important Notes Codes: Install in accordance with all local and national electrical codes. Environment: Ambient operating temperature: 0-40°C, 32-104°F, 0-90% humidity, non-condensing. Indoor use only. Wallplates: Lutron Claro® and Satin ColorsTM wallplates are recommended for best color match and clean aesthetic appearance. Do not paint controls or wallplates. Cleaning: Clean with a soft damp cloth only. Do not use any chemical or abrasive cleaners. Wallboxes: Lutron recommends using 3.5" (89mm) deep wallboxes for easier installation. RF Device Placement: RF Keypads must be located within 30 feet (9m) of an RF Signal Repeater or an RF Processor. RF Keypads will not function until they are addressed and programmed. See the HomeWorks Utility online help. Installation 5. Attach Lutron Claro® or Satin ColorsTM wallplate adapter and wallplate. Danger - Locate and remove fuse or lock circuit breaker in the OFF position before proceeding. Wiring with power ON may result in personal injury. a. Loosely install keypad mounting screws. b. Tighten adapter mounting screws snug. 1. Turn power OFF at fusebox or circuit breaker. c. Tighten keypad mounting screws until keypad is flush to wall (do not over-tighten). 2. Prepare wires. When making wire connections, fol- d. Snap wallplate onto adapter. low the recommended strip lengths and combinations for the supplied wire connectors. Note: Wire connectors provided are suitable for copper wire only. 6. Restore power. Small: Strip insulation .375" (10mm) for 14AWG (2.5mm2). Strip insulation .5" (13mm) for 16AWG (2.5mm2). Use to join one 14AWG supply wire with one 16 or 18AWG (1.0mm2) control wire. Small 3. Wiring: See Wiring Diagram (page 3) 4. Push all wires back into the wallbox and loosely fasten the control to the wallbox using the screws provided. Do not pinch the wires. Mounting Diagram Keypad Mounting Screws Adapter Mounting Screws Wallbox Keypad Included: Wallplate Adapter* Wallplate* Wire Connectors (3) * Wallplate and Adapter are purchased separately. Mounting Screws (2) Wiring Diagram Hot/Live Black Neutral White 120/127V 50/60Hz Green Earth/Ground Troubleshooting Guide RF Keypads will not function until they are addressed and programmed. See the HomeWorks Utility online help. Keypad is working properly when LEDs light up and loads respond as buttons are pressed. Symptom LEDs don't light up. Cause and Action Power not present at keypad • Circuit breaker OFF. Turn ON breaker. • Wiring error. Check wiring to be sure it agrees with installation instructions and wiring diagram. LEDs cycle from top to bottom sequentially. Keypad is properly powered but... • Keypad has not been addressed. See the HWI Utility online help for addressing details. LEDs blink twice while cycling from top to bottom sequentially. Keypad is properly powered but... • Keypad has not been programmed. See the HWI Utility online help for programming details. Keypad cannot be addressed. Keypad is out of RF communications range. • Move RF Repeater or RF Processor to within 30 feet of keypad. LEDs light when pressed, but the system response is not correct. Improper programming • Check programming in HWI Utility. FCC Information Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the seperation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could void the user’s authority to operate this equipment. Industry Canada Information The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met. Technical and Sales Assistance If you need assistance, call the toll-free Lutron Technical Support Center. Please provide exact model number when calling. (800) 523-9466 (U.S.A., Canada and the Caribbean) Other countries call: Tel: (610) 282-3800 Fax: (610) 282-3090 Visit our Web site at www.lutron.com Lutron Electronics Co., Inc. 7200 Suter Road Coopersburg, PA 18036-1299 Made and printed in the U.S.A. 11/02 P/N 043-111 Rev. A LIMITED WARRANTY Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within two years after purchase. For warranty service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid. Telephone the Lutron Technical Support Center toll free at 800-523-9466. After the two year period, a pro-rated warranty applies to this product until eight years after the purchase. For more information regarding this warranty contact your Lutron representative. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO TWO YEARS FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION, REMOVAL OR REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, OR IMPROPER OR INCORRECT REPAIR, OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUENTIAL DAMAGES. LUTRON’S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.This product may be covered by one or more of the following U.S. patents: 4,835,343; 4,889,999; 5,170,068; 5,237,207; D378,814; D436,579 and corresponding foreign patents. U.S. and foreign patents pending. Lutron, Claro, and HomeWorks are registered trademarks and Satin Colors is a trademark of Lutron Electronics Co., Inc. © 2002 Lutron Electronics Co., Inc.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Create Date : 2002:11:14 11:50:14-05:00 Modify Date : 2002:11:14 11:50:14-05:00 Page Count : 4 Creation Date : 2002:11:14 16:50:14Z Mod Date : 2002:11:14 16:50:14Z Producer : Acrobat Distiller 5.0.5 (Windows) Author : rlau Metadata Date : 2002:11:14 16:50:14Z Creator : rlau Title : RF KP Instr.qxdEXIF Metadata provided by EXIF.tools